Search results for: experimental study
-
Pilot Testing of Developed Multimodal Biometric Identity Verification System
PublicationThe bank client identity verification system developed in the course of the IDENT project is presented. The total number of five biometric modalities including: dynamic signature proofing, voice recognition, face image verification, face contour extraction and hand blood vessels distribution comparison have been developed and studied. The experimental data were acquired employing multiple biometric sensors installed at engineered...
-
Dissociative ionization dynamics of dielectric gas C3F7CN
PublicationFluoronitrile C3F7CN is a promising candidate for the replacement of SF6 dielectric gas in high-voltage insulation. We present a combined experimental and theoretical study on its ionization dynamics probed in the 0-100 eV energy range. We exploited the total ion collection technique to determine the absolute ionization cross section, mass spectrometry to determine the fragment branching ratios and ab initio nonadiabatic molecular...
-
Validation of Services Supporting Healthcare Standards Conformance
PublicationThe paper presents the results of experimental validation of a set of innovative software services supporting processes of achieving, assessing and maintaining conformance with standards and regulations. The study involved several hospitals implementing the Accreditation Standard promoted by the Polish Ministry of Health. First we introduce NOR-STA services that implement the TRUST-IT methodology of argument management. Then we...
-
VIBRATION PROBLEMS OF AN EXAMPLE OF TEMPORARY STEEL GRANDSTAND UNDER HUMAN-INDUCED EXCITATION
PublicationLighter and slender structural members of a typical grandstand leads to a significant reduction in the frequencies, that is why such structures are more easily induced to vibrations. The aim of the present paper is to show the results of our experimental studies and the numerical analyses, focused on the behaviour of a part of a typical temporary steel grandstand under dynamic loads. The peak values of accelerations of a steel...
-
Wavelet Transform Analysis of Temperature Modulated Gas Sensor Response
PublicationThe aim of the study was to evaluate whether it is possible to extract the information about the gas concentration despite the influence of humidity. Commercial semiconductor sensor response was examined under the application of a periodic temperature change. The data was collected using measurement protocol for different concentrations of ammonia at specified levels of relative humidity. In this work we focused on the evaluation...
-
Application of Headspace Solid-phase Microextraction with Poly(1-vinyl-3- Hexylimidazolium Chloride) Polymeric Ionic Liquid Coating using GC - MS to Determine Volatile Fatty Acids in Dairy Wastewater
PublicationVolatile fatty acids were determined in this study using headspace solid-phase microextraction (HS-SPME) with a poly(1-vinyl-3-hexylimidazolium chloride) polymeric ionic liquid coated fiber followed by gas chromatography - mass spectrometry. Experimental parameters such as extraction time and temperature, sample volume as well as desorption time and temperature were optimized. Detection limits of the method were in the range of...
-
Investigations on mixture preparation for two phase adiabatic pressure drop of R134a flowing in 5 mm diameter channel
PublicationThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a. Study cases have been set for a mass flux varying from 200 to 400 kg/m2 s, at the saturation temperature of 19.4 ◦C. Obtained experimental data was compared with the available correlations from the literature for the frictional pressure drop during adiabatic flow. Influence of mixture preparation on pressure drop was investigated, for...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena, however their description with a single correlation has yet to be suggested. In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the bubble generation is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such...
-
Experiment-Based Study of Heat Dissipation from the Power Cable in a Casing Pipe
PublicationThe paper deals with the important challenges in terms of electricity transmission by means of underground cable lines. The power cable’s performance is characterized by an ampacity that represents its maximum electric current-carrying capacity. The ampacity of power cables depends on their ability to diffuse the heat generated by the current flow into the environment. In the performed research, the analysis of the efficiency of...
-
Influence of windsurfing fin stiffness distribution on the lift-drag characteristics
PublicationThis article addresses the problem of determining the hydromechanical loads generated by flexible hydrofoils. The research was done on the example of the composite windsurfing fin for the RS:X monotype class. Despite the assumption of fins identity, everyday practice showed that variations of mechanical properties occur and strongly affect their performance. Therefore, we decided to study the differences between the windsurfing...
-
Mathematical approach to design 3D scaffolds for the 3D printable bone implant
PublicationThis work demonstrates that an artificial scaffold structure can be designed to exhibit mechanical properties close to the ones of real bone tissue, thus highly reducing the stress-shielding phenomenon. In this study the scan of lumbar vertebra fragment was reproduced to create a numerical 3D model (this model was called the reference bone sample). New nine 3D scaffold samples were designed and their numerical models were created....
-
Paweł Możejko dr hab.
People -
Artificial neural network prophecy of ion exchange process for Cu (II) eradication from acid mine drainage
PublicationThe removal of heavy metal ions from wastewater was found to be significant when the cation exchange procedure was used effectively. The model of the cation exchange process was built using an artificial neural network (ANN). The acid mine drainage waste’s Cu(II) ion was removed using Indion 730 cation exchange resin. Experimental data from 252 cycles were recorded. In a column study, 252 experimental observations validated the...
-
Surface sliding in human abdominal wall numerical models: Comparison of single-surface and multi-surface composites
PublicationDetermining mechanical properties of abdominal soft tissues requires a coupled experimental-numerical study, but first an appropriate numerical model needs to be built. Precise modeling of human abdominal wall mechanics is difficult because of its complicated multi-layer composition and large variation between specimens. There are several approaches concerning simplification of numerical models, but it is unclear how far one could...
-
A novel in vivo approach to assess strains of the human abdominal wall under known intraabdominal pressure
PublicationThe study concerns mechanical behaviour of a living human abdominal wall. A better mechanical understanding of a human abdominal wall and recognition of its material properties is required to find mechanically compatible surgical meshes to significantly improve the treatment of ventral hernias. A non-invasive methodology, based on in vivo optical measurements is proposed to determine strains of abdominal wall corresponding to...
-
Eksperymentalne i numeryczne badania parametrów dynamicznych trybuny stalowej
PublicationTrybuny stalowe to konstrukcje, które odnajdują swoje zastosowanie głównie podczas wydarzeń sportowych, koncertów muzycznych oraz innych wydarzeń, którym towarzyszą rytmiczne aktywności widzów i głośna muzyka. Ze względu na smukłość oraz lekkość elementów z jakich wykonana jest konstrukcja trybuny jest ona bardzo łatwo wzbudzana przez ludzi do drgań. Z przeprowadzonej w pracy [4] analizy modalnej wynika, że masa ludzi prowadzi...
-
Elastic scattering of electrons by water: An ab initio study
PublicationIn this work we devise a theoretical and computational method to compute the elastic scattering of electrons from a non-spherical potential, such as in the case of molecules and molecular aggregates. Its main feature is represented by the ability of calculating accurate wave functions for continuum states of polycentric systems via the solution of the Lippmann-Schwinger equation, including both the correlation effects and multi-scattering...
-
Application of gaze tracking technology to quality of experience domain
PublicationA new methodological approach to study subjective assessment results employing gaze tracking technology is shown. Notions of Human-Computer Interaction (HCI) and Quality of Experience (QoE) are shortly introduced in the context of their common application. Then, the gaze tracking system developed at the Multimedia Systems Department (MSD) of Gdansk University of Technology (GUT) is presented. A series of audio-visual subjective...
-
A two dimensional approach for modelling of pennate muscle behaviour
PublicationThe purpose of this study was to elaborate a two-dimensional approach for unipennate and bipennate striated skeletal muscle modelling. Behavior of chosen flat pennate muscle is modelled as a rheological system composed of serially linked passive and active fragments having different mechanical properties. Each fragment is composed of three elements: mass element, elastic element and viscous element. Each active fragment furthermore...
-
Wave propagation in damage assessment of ground anchors
PublicationThe inspection possibilities of ground anchors are limited to destructive test such as pull-out test. Guided wave propagation gives an opportunity to develop an inspection system dedicated to determine the condition of inspected element without violation of their integrity. In this paper the experimental study on wave propagation in laboratory models of ground anchors are presented. Experiments were conducted for different bonding...
-
HEAT TRANSFER CHARACTERISTICS OF ENHANCED SHELL AND COIL HEAT EXCHANGER
PublicationIn the paper authors presented their own constructions of shell and tube heat exchangers with intensified heat transfer. The shell and coils heat exchangers are in common use in heat ventilations and air conditioning systems. Those types of recuperators are quite simple constructions, the low value of pressure drops and good conditions of heat transfer. The present study shows an experimental investigation of the heat transfer...
-
UNDERWATER NOISE GENERATED BY A SMALL SHIP IN THE SHALLOW SEA
PublicationStudy of the sea noise has been a subject of interest for years. The first work of this scope were published at the turn of the twentieth century by Knudsen (KNUDSEN et al., 1948) and G. Wenz (WENZ, 1962). Disturbances called "shipping noise" are one of the important components of the sea noise. In this work the results of an experimental research of underwater noise produced by a small ship of a classic propulsion are...
-
Numerical Evaluation of Dynamic Response of a Steel Structure Model under Various Seismic Excitations
PublicationThe present paper reports the results of the study, which was designed to perform a numerical evaluation of dynamic response of a single-storey steel structure model. The experimental model was previously subjected to a number of different earthquake ground motions during an extensive shaking table investigation. The analyzed structure model was considered as a 1-DOF system with lumped parameters, which were determined by conducting...
-
Selected Aspects of Pavement Texture Influence on Tire Rolling Resistance
PublicationTire rolling resistance has a significant influence on fuel consumption in cars and trucks and on CO2 emissions. Rolling resistance depends on the tire construction, pavement texture and stiffness, as well as environmental and traffic conditions. This article presents a pilot study on the impact of pavement texture on the rolling resistance of passenger car tires. Reasons why Mean Profile Depth is not a good descriptor of pavement...
-
Numerical modeling of GPR field in damage detection of a reinforced concrete footbridge
PublicationThe paper presents a study on the use of the ground penetrating radar (GPR) method in diagnostics of a footbridge. It contains experimental investigations and numerical analyses of the electromagnetic field propagation using the finite difference time domain method (FDTD). The object of research was a reinforced concrete footbridge over a railway line. The calculations of the GPR field propagation were performed on a selected cross-section...
-
Energy requirements for methods improving gas detection by modulating physical properties of resistive gas sensors
PublicationAbstract. One of the most important disadvantage of resistive gas sensors is their limited gas selectivity. Therefore, various methods modulating their physical properties are used to improve gas detection. These methods are usually limited to temperature modulation or UV light irradiation for the layers exhibiting photocatalytic effect. These methods cause increased energy consumption. In our study we consider how much energy...
-
Study of the Performance of DSSS UAC System Depending on the System Bandwidth and the Spreading Sequence
PublicationA signal transmitted in an Underwater Acoustic Communication (UAC) system operating in a shallow-water channel suffers from strong time dispersion due to multipath propagation. This causes the Inter-Symbol Interference (ISI) observed in the received signal, which significantly limits the communication system’s reliability and transmission rate. In such propagation conditions, the Direct-Sequence Spread Spectrum (DSSS) method is...
-
Guided wave propagation in debonding detection in CFRP-reinforced steel plate-like structures
PublicationThe present study investigates the guided wave propagation in multilayered steel specimens reinforced with carbon fiber reinforced polymer (CFRP) through theoretical, numerical, and experimental means. The effectiveness of externally bonded reinforcement (EBR) relies heavily on the bonding quality between the CFRP and the substrate. Premature debonding, a prevalent and hazardous defect, can arise from suboptimal manufacturing processes,...
-
Non-destructive inspection of ground anchors using guided wave propagation
PublicationThis paper deals with numerical and experimental investigations of specific problems of guided wave propagation in ground anchors. The research focuses on recognizing the phenomenon of the energy transfer between anchor components. Particular attention is paid to characteristic features of guided waves propagating in free and embedded parts of the tendon, at the interface between the tendon and the surrounding anchor body as well...
-
Applicability of arrays of microjets heat transfer correlations to design compact heat exchangers
PublicationThe article presents experimental studies on a compact heat exchanger with heat transfer intensification by means of impinging microjets. The pursuit to provide high performance of heat exchangers is a response to the demand both in economics and in the universal tendency to miniaturization of industrial equipment. This paper presents the design and tests of a prototype, microjet heat exchanger. The modular design of the heat exchanger...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
Verification of selected calculation methods regarding shear strength in beams without web reinforcement
PublicationThe purpose of the article was to compare selected calculation methods regarding shear strength in reinforced concrete beams without web reinforcement. Several calculation methods were tested. This included codes: PN-EN 1992-1-1:2008, ACI 318-14 and fib Model Code for Concrete Structures 2010. The analysis also consists of authorial methods published in technical literature. Calculations of shear strengths were made based on experimental...
-
High load capacity spur gears with conchoidal path of contact
PublicationThe present study is devoted to investigation of spur gears with a conchoidal path of contact and a convex-convex contact between teeth. The load capacity and energy efficiency were evaluated using both theoretical and experimental approaches. The theoretical analysis showed that the conchoidal gear pairs are 5–21% stronger in terms of contact stress and have similar energy efficiency as compared to the involute gear pairs of the...
-
Analysis of ultimate compressive strength of cracked plates with the use of DOE techniques
PublicationThe objective of this work is to investigate the structural compressive response of plates with locked cracks accounting for all relevant factors and correlation between them. The nonlinear FE model considering both geometric and material nonlinearities is employed herein, and the FE model of the structural response of intact plates is validated with the available experimental data. In the common studies, based on One Factor at...
-
Experimental Verification of the CFD Model of the Squeeze Film Lifting Effect
PublicationAbstract: The presented study shows the results of the research into the squeeze film levitation phenomena. The system introduced in the investigation is composed of a vibrating surface, air squeeze film, and the surface of the body freely suspended over the film. The use of the CFD (Computational Fluid Dynamics) model used in the system allows us to determine the steady state, periodic behavior of the air film (described by Navier–Stokes,...
-
Design and experimental verification of multi-layer waveguide using pin/hole structure
PublicationThis study presents a novel technique for minimizing RF leakage in metallic hollow waveguides fabricated using the multilayer split-block method. By integrating a pin/hole wall into the split-block multilayers, a substantial reduction of RF leakage can be achieved while reducing the circuit size and mitigating the performance variations. To validate the proposed approach, a slot antenna fed by single ridge waveguide has been prototyped...
-
Observing uncertainty in music tagging by automatic gaze tracking
PublicationIn this paper, a new approach to observe music file tagging process by employing a gaze tracking system is proposed. The study was conducted with the participation of twenty subjects having different musical experience. For the purpose of the experiments a website survey based on a musical database was prepared. It allowed to gather information about music experience of subjects along with music characteristics such as genre, tempo,...
-
Visual Data Encryption for Privacy Enhancement in Surveillance Systems
PublicationIn this paper a methodology for employing reversible visual encryption of data is proposed. The developed algorithms are focused on privacy enhancement in distributed surveillance architectures. First, motivation of the study performed and a short review of preexisting methods of privacy enhancement are presented. The algorithmic background, system architecture along with a solution for anonymization of sensitive regions of interest...
-
Air journal bearing utilizing near-field acoustic levitation: stationary shaft case
PublicationResults of a study to examine a unique idea of self-levitating journal bearing are presented in this paper. the idea represents a radical departure from the current bearing technology. it utilisesacoustic levitation, which relies on the sound energy radiated by an object supporting a load. acoustic levitation has been demonstrated to support loads of up to 10 kg. in order to support a load theacoustic wave emitted by the radiating...
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublicationThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
Correlation between charge density waves and antiferromagnetism in Nd1−xGdxNiC2 solid solutions
PublicationWe report a study on the evolution of a charge density wave and antiferromagnetism in the series of the polycrystalline solid solution Nd1−xGdxNiC2 (0 _ x _ 1) by means of magnetic and transport properties measurements. The experimental results reveal the violation of the de Gennes law and a strong correlation between the Peierls, Néel, and Curie-Weiss temperatures, which strongly suggests a cooperative interaction between the...
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublicationThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
Failure characterisation of sandwich beams using integrated acoustic emission and digital image correlation techniques
PublicationThe paper presents the experimental study of the failure behaviour of sandwich beams subjected to bending. The samples examined are sandwich beams made of polyethylene terephthalate foam core and glass fibre-reinforced polymer laminate face sheets. In a series of experiments, it has been proposed to integrate diagnostic techniques with acoustic emission and digital image correlation to accurately track the cracking process on the...
-
Metoda diagnostyki łożysk na podstawie analizy przebiegów prądu i napięcia zasilającego silnik indukcyjny.
PublicationW niniejszej monografii przedstawiono oryginalne podejście i realizację diagnostyki łożysk silników indukcyjnych przy użyciu metody opartej na pomiarach i analizie iloczynu wartości chwilowych prądu i napięcia zasilającego maszyny. Uzyskane wyniki badań eksperymentalnych na obiektach rzeczywistych okazały się zbieżne z wynikami badań symulacyjnych i potwierdziły, że powstanie uszkodzeń łożysk w silniku skutkuje pojawieniem się...
-
Estimation and modeling hydrolysis of slowly biodegradable substrate based on the batch respirometric tests in activated sludge systems
PublicationNowadays, appropriate determination of chemical oxygen demand (COD) fractionation together with degradation kinetics of organic compounds have a prime importance on the design and operation of activated sludge systems. Batch respirometric tests based on the oxygen uptake rates (OUR) and corresponding COD is accepted method to reflect the consumption of biodegradable substrates. The influence of the readily biodegradable (Ss) fraction...
-
Application of a three‑dimensional (3D) breast cancer model to study macrophage polarization
Publication -
Experimental ultimate strength assessment of stiffened plates subjected to marine immersed corrosion
PublicationThis study experimentally analyses the impact of marine immersed corrosion degradation on the compressive strength of the stiffened plates where the lower degradation levels were considered. The corrosion degradation test was accelerated by controlling the natural corrosion environmental factors, avoiding applying an electric current. Different groups of corrosion degradation levels and initial plate thicknesses were investigated....
-
Mathematical modelling of gasification process of sewage sludge in reactor of negative CO2 emission power plant
PublicationSewage sludge is a residue of wastewater processing that is biologically active and consists of water,organic matter, including dead and alive pathogens, as well as organic and inorganic contaminants suchas polycyclic aromatic hydrocarbons (PAHs) and heavy metals. Due to the nature of sewage sludge and itspossible influence on human health and wellbeing, it is a subject of various regulations. Currently,sewage sludge is considered...
-
Combining X-ray tomogrpahy imaging and DEM simulations to investigate granular material flow during silo discharging
PublicationEven after few decades of research, the study of particle motion taking place during silo discharging hasn’t been fully addressed, both experimentally and numerically, because of nontrivial behaviors that occur during associated flow patterns. For instance, discrete element method (DEM) has shown good qualitative prediction potential of velocity profile, but, on the other hand, frequently failed to match quantitatively experimental...
-
Eksperymentalna analiza wpływu ruchu posuwisto-zwrotnego i obrotowego oraz miejscowych zmian geometrii na skuteczność wypierania cieczy wiertniczych z przestrzeni pierścieniowej
PublicationRozprawa przedstawia analizę wpływu ruchu kolumny rur stosowanego w wiertnictwie oraz miejscowych zmian geometrii przestrzeni pierścieniowej na skuteczność procesu wypierania się cieczy. Jest to pierwsze badanie w otwartej literaturze omawiające te czynniki, w którym opisano wyniki eksperymentów na dedykowanym stanowisku badawczym. W pracy omówiony został wpływ węglowodorów na współczesną cywilizację, jak również wpływ skuteczności...