displaying 1000 best results Help
Search results for: comparison
-
Nonlinear viscoelasticity in Three Dimensional filler reinforced rubber composites and nanocomposites
PublicationThis chapter describes the influence of three-dimensional nanofillers used in elastomers on the nonlinear viscoelastic properties. In particular, this part focuses and investigates the most important three-dimensional nanoparticles, which are used to produce rubber nanocomposites. The rheological and the dynamic mechanical properties of elastomeric polymers, reinforced with spherical nanoparticles, like POSS, titanium dioxide and...
-
Modeling of event trees for the rapid scenario development
PublicationThe paper concerns the safety of ships in abnormal/damage conditions. Some conclusions following from the research associated with development of a method for safety assessment of ships in abnormal/damage conditions is presented in the paper. The method called SSAMADC (Ship Safety Assessment Method in Abnormal/Damage Conditions) is a risk-based method and is connected with application of the quantitative risk assessment QRA approach....
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublicationThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublicationThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
GRAPHICAL REPRESENTATION OF MUSIC SET BASED ON MOOD OF MUSIC. GRAFICZNA PREZENTACJA ZBIORU MUZYCZNEGO OPARTA NA ANOTACJI NASTROJU MUZYKI
PublicationOne of the features for music recommendation, which is useful and intuitive for music listen-ers, is “mood”. The paper presents an approach to graphical representation of mood of music pieces. Subjective evaluation based on listening tests is performed for assigning mood labels of 150 pieces of music and placing them on the 2D mood plane. As a result, a map of songs is created, where music excerpts with similar mood are organized...
-
The ranks of Japanese industrial sectors: 2005-2011
PublicationThe purpose of the current study is to expand the previous study which analyzes the industrial sectors ranks of specific countries. More specifically, the study aims to conduct a comparison in terms of the ranks of Japanese industrial sectors on the specific analysis period. The analysis period of the study is 2005-2011. Using the previous study as a reference, the study employs the Input-Output (IO) approach as an analysis instrument....
-
Observation Value Analysis – Integral Part of Bayesian Diagnostics
PublicationThe decision making process, in general, is understood as a process of selecting one of the available solutions to the problem. One of possible approaches supporting the process is Bayesian statistical decision theory providing a mathematical model to make decisions of a technical nature in conditions of uncertainty. Regarding above, a detailed subject of the research is to analyze the value of the observation, which is a part...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements Dataset
PublicationThe dataset titled EH36 steel for shipbuilding (plate thickness 50 mm) – CMOD – force record, a0/W=0.6 contains a CMOD (Crack Mouth Opening Displacement) – Force record which is the base for evaluation of the fracture toughness of structural steel. Bend specimens with a Bx2B section (B = 50 mm), and relative initial crack length a0/W=0.60 were used. The test was carried out at ambient temperature in accordance with the ISO 12135...
-
Measurement of temperature at sliding polymer surface by grindable thermocouples
PublicationThis paper is devoted to experimental study of capabilities and limitations of grindable thermocouples as applied to polymer materials sliding on metal. Chromel–alumel and chromel–copel grindable thermocouples have been developed and tested for wide ranges of contact pressure and sliding velocity. The background temperature of the sliding surface can be determined as the lower envelope of the signal from the grindable thermocouple....
-
The Impact of Contemporary Technology on Shell Structures: Material and Light Solutions
PublicationWith the development of technology and the materials used, shell structures have developed into more complex forms. This article is a comparison between contemporary and historical shell structures. The change is an effect of the evolution in the design process that is the result of parametric design thinking. The study aims to investigate the impact of new technologies on the architectural form of shell structures. Was there any...
-
Experimental Study of Polish Sausage Drying Kinetics and Contraction by Image Data Analysis
PublicationThe goal of this paper has been to add an experimental data set for drying a meat product and provide a comparison with well-established thin-layer drying models. This article presented experimental investigations on the convective drying of Polish sausage slices at a temperature of 40°C. Slices have been in the thickness of 3 to 8mm. Measurements of mass loss and size change were performed. The data have been presented in the...
-
Experimental study of the multi-disc negative brake for a hydraulic motor
PublicationThis paper describes the methodology for experimental testing of a multi-disc brake. The construction of this brake was also present. The brake is dedicated to hydraulic motors with a small working volume. Experimental tests were carried out on a brake with plates immersed in oil and, for comparison, tests were carried out on a dry brake. As a result of the tests, the permissible torque (load) that is able to transfer the brake...
-
Branża IT – wyzwania związane z zarządzaniem kapitałem ludzkim
PublicationArtykuł dotyczy procesów zarządzania kapitałem ludzkim w firmach IT, w których największe wyzwania wiążą się z dwoma obszarami: zatrudniania i zatrzymywania specjalistów IT w organizacji. Działy HR prześcigają się w stosowaniu coraz to nowszych rozwiązań, aby pozyskać oraz motywować kompetentnych informatyków do pracy na rzecz firmy. Głównym celem artykułu jest prezentacja działań dotyczących rekrutacji oraz motywowania pracowników...
-
Proces wytwarzania e-kursu. Studium przypadku.
PublicationArtykuł definiuje proces wytwarzania e-kursu i e-lekcji oraz kolejne jego etapy, zaczynając od okre - ślania celu i odbiorcy, a kończąc na udostępnieniu treści. Na podstawie opisanego procesu przedstawiane jest stu - dium przypadku dla e-kursu prowadzonego na studiach zaocznych na Wydziale ETI Politechniki Gdańskiej na przedmiocie Strategie informatyzacji. Artykuł pokazuje też ewaluację studium przypadku, zarówno na poziomie oceny...
-
Zróżnicowanie zadłużenia w zależności od wielkości przedsiębiorstwa
PublicationW artykule przedstawiono różnice w sposobie kształtowania wartości wskaźników z obszaru zadłużenia pomiędzy małymi, średnimi i dużymi przedsiębiorstwami. W trakcie przeprowadzonych badań uwzględniono 97 471 sprawozdań finansowych przedsiębiorstw, prowadzących działalność gospodarczą w 12 różnych działach polskiej gospodarki narodowej. Do potwierdzenia zróżnicowania zadłużenia w zależności od wielkości przedsiębiorstwa wykorzystano...
-
ZARZĄDZANIE ZESPOŁEM WIRTUALNYM JAKO WYZWANIE DLA LIDERA ZESPOŁU
PublicationRozdział dotyczy zarządzania zespołem wirtualnym, który charakteryzuje się rozproszeniem członków zespołu oraz współpracą za pośrednictwem technologii informacyjnej. Tak funkcjonujące zespoły nakładają na lidera dodatkowe wyzwania związane z koniecznością kompensowania braku bezpośredniego kontaktu oraz samodzielnością poszczególnych osób w zespole. Przedstawiono najważniejsze zadania, które podnoszą efektywność zarządzania zespołem...
-
ZRÓŻNICOWANIE PŁYNNOŚCI FINANSOWEJ W ZALEŻNOŚCI OD WIELKOŚCI PRZEDSIĘBIORSTWA
PublicationW artykule przedstawiono różnice w sposobie kształtowania wartości wskaźników z obszaru płynności finansowej pomiędzy małymi, średnimi i dużymi przedsiębiorstwami. W trakcie przeprowadzonych badań uwzględniono 97 471 sprawozdań finansowych przedsiębiorstw, prowadzących działalność gospodarczą w 12 różnych działach polskiej gospodarki narodowej. Do potwierdzenia zróżnicowania płynności finansowej w zależności od wielkości przedsiębiorstwa...
-
An Aqueous Exfoliation of WO3 as a Route for Counterions Fabrication—Improved Photocatalytic and Capacitive Properties of Polyaniline/WO3Composite
PublicationIn this paper, we demonstrate a novel, electrochemical route of polyaniline/tungsten oxide (PANI)/WO3) film preparation. Polyaniline composite film was electrodeposited on the FTO (fluorine-doped tin oxide) substrate from the aqueous electrolyte that contained aniline (monomer) and exfoliated WO3 as a source of counter ions. The chemical nature of WO3 incorporated in the polyaniline matrix was investigated using X-ray photoelectron...
-
The future of the logistician education in Poland and Ukraine: comparative analysis of the student’s opinion
PublicationBackground: A professional future is the next logical step after a student completes their chosen degree course. More frequently, even during their studies, young people seek opportunities to participate in various conferences, training courses, internships, work placements, and to travel abroad, etc. All of this has one main goal - to increase the student's attractiveness as a potential employee on the labour market. Thus, it...
-
Production of fuel briquette from solid waste biomass using natural resin as a binder
PublicationBackground: This research aimed to evaluate the use of natural resin as a binder for the production of fuel briquette from solid waste biomass.Methods: Proximate analyses were made for fuel briquette prepared from solid waste biomass using natural resin as a binder in comparison with using starch as a binder.Results: The results for density, percent content of moisture, percent content of volatile matter, percent...
-
A Comparative Study of Fuzzy SMC with Adaptive Fuzzy PID for Sensorless Speed Control of Six-Phase Induction Motor
PublicationMulti-phase motors have recently replaced three-phase induction motors in a variety of applications due to the numerous benefits they provide, and the absence of speed sensors promotes induction motors with variable speed drives. Sensorless speed control minimizes unnecessary speed encoder cost, reduces maintenance, and improves the motor drive’s reliability. The performance comparison of the fuzzy sliding mode controller (FSMC)...
-
A Comparative Study of Fuzzy SMC with Adaptive Fuzzy PID for Sensorless Speed Control of Six-Phase Induction Motor
PublicationMulti-phase motors have recently replaced three-phase induction motors in a variety of applications due to the numerous benefits they provide, and the absence of speed sensors promotes induction motors with variable speed drives. Sensorless speed control minimizes unnecessary speed encoder cost, reduces maintenance, and improves the motor drive’s reliability. The performance comparison of the fuzzy sliding mode controller (FSMC)...
-
Production of fuel briquette from solid waste biomass using natural resin as a binder
PublicationAbstract Background: This research aimed to evaluate the use of natural resin as a binder for the production of fuel briquette from solid waste biomass. Methods: Proximate analyses were made for fuel briquette prepared from solid waste biomass using natural resin as a binder in comparison with using starch as a binder. Results: The results for density, percent content of moisture, percent content of volatile matter, percent content...
-
Dissociative electron attachment to benzoic acid (C7H6O2)
PublicationThe dissociative electron attachment (DEA) to benzoic acid (C6H5COOH) has been studied using an experimental crossed beam setup of a quadrupole mass spectrometer and a trochoidal electron monochromator. Relative partial cross sections for the DEA to produce negative ion fragments show the main channels for dissociation. The comparison of the present results with the ultraviolet photoelectron spectrum of benzoic acid [J. Meeks,...
-
Anti-plane surface waves in media with surface structure: Discrete vs. continuum model
PublicationWe present a comparison of the dispersion relations derived for anti-plane surface waves using the two distinct approaches of the surface elasticity vis-a-vis the lattice dynamics. We consider an elastic half-space with surface stresses described within the Gurtin–Murdoch model, and present a formulation of its discrete counterpart that is a square lattice half-plane with surface row of particles having mass and elastic bonds different...
-
Optical activity and electro-optic effect of l-arginine doped KDP single crystals
PublicationWe have used the modified polarimetric methods to study optical activity (OA) in the potassium dihydrogenphosphate (KDP) crystals doped with 0.7, 1.4 and 3.8 wt% L-arginine (L-arg) amino acid. Crystals were grown by the temperature reduction method. Small changes of the absolute eigen waves ellipticity and OA values in doped crystals were noted. We have experimentally determined the signs of OA in the [1 00] and [01 0] directions...
-
Promising Nanoparticle-Based Heat Transfer Fluids—Environmental and Techno-Economic Analysis Compared to Conventional Fluids
PublicationProviding optimal operating conditions is one of the major challenges for effective heating or cooling systems. Moreover, proper adjustment of the heat transfer fluid is also important from the viewpoint of the correct operation, maintenance, and cost efficiency of these systems. Therefore, in this paper, a detailed review of recent work on the subject of conventional and novel heat transfer fluid applications is presented. Particular...
-
DMI measurements impact on a position estimation with lack of GNSS signals during Mobile Mapping
PublicationNowadays, Mobile Laser Scanning is common in use in addition to geodesy measurements. The data which are provided by the system characterizes with high precision and flexibility. To precise mapping, the accuracy of the data should be maintained. In Poland, according to the minister’s dispositions, the accuracy of the data should not exceeded 10 cm. With fully operated system it is easy to uphold, but there is a situation when a...
-
Pylon foundation of a cable stayed bridge at the motorway ring road of Wrocław
PublicationThe largest bridge of the motorway ring road of Wroclaw is a cable stayed bridge over the Odra river near Rędzin. Due to hydrogeological conditions of the ground it was not convenient to use standard bored piles of high length. Instead shorter piles were applied with additional improvement by cement injections at the pile toes. This decision was possible by extending ground investigation program and application of numerical modeling...
-
Microwave-assisted preparation of potato starch silicated with silicic acid
PublicationApplication of microwave irradiation for the silication of granular potato starch with silicic acid, and the properties of silicated starch were investigated. Potato starch was esterified on 20 min microwave irradiation of starch with silicic acid, applying the power of 450 or 800Wand, for comparison, on 120 min convectional heating of the reagent blend at 100 ◦C. The degree of esterification and the reaction efficiency did not...
-
A Substrate Integrated Waveguide (SIW) Bandpass Filter in A Box Configuration With Frequency-Dependent Coupling
PublicationThis letter presents the design of a microwave bandpass filter with frequency-dependent coupling implemented in substrate integrated waveguide (SIW) technology. The proposed filter implements a four-pole generalized Chebyshev filtering function with two transmission zeros. Resonators are arranged in an extended box configuration with dispersive coupling on a main signal path, which produces an extra zero in comparison to classical...
-
Traffic Type Influence on Performance of OSPF QoS Routing
PublicationFeasibility studies with QoS routing proved that the network traffic type has influence on routing performance. In this work influence of self-similar traffic for network with DiffServ architecture and OSPF QoS routing has been verified. Analysis has been done for three traffic classes. Multiplexed ON-OFF model was used for self-similar traffic generation. Comparison of simulation results were presented using both relative and...
-
Role of nitrogen in optical and electrical band gaps of hydrogenated/hydrogen free carbon nitride film
PublicationWe report the optical and electrical band gap energy of amorphous hydrogenated carbon nitride (a-HCNx) and carbon nitride (a-CNx) as a function of nitrogen concentration (N/C). The optical band gap of a-HCNx and a-CNx films has been determined by means of Ellipsometry and UV-VIS. Both optical and electrical band gaps increase with elevated nitrogen concentration. Experimentally obtained electrical band gap is compared with the...
-
Fracture mechanics model of cutting power versus widespread regression equations while wood sawing with circular saw blades
PublicationA comparison of the theoretical cutting power consumption results forecasted with the model (FM_CM model) which include work of separation (fracture toughness) in addition to plasticity and friction, and two widespread regression equations while wood sawing with circular saw blades has been described. in and cutting power consumption forecasted. In computations of the cutting power consumption during rip sawing of Scots pine wood...
-
Empirical verification in industrial conditions of fracture mechanics models of cutting power prediction
PublicationA comparison of experimental results obtained in the industrial conditions at a sawmill located in the Baltic Natural Forest Region (PL) and theoretical cutting power consumption forecasted with the models which include work of separation (fracture toughness) in addition to plasticity and friction has been described. In computations of cutting power consumption during rip sawing of Scots pine wood (Pinus sylvestris L.) values of...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublicationThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
High temperature drying of beech with content of tension wood
PublicationThe presented artcle is focused on comparison of tension and normal wood of beech (Fagus sylvatica L.) in a high-temperature drying process. Samples of 26 mm thickness were selected from sapwood zone with different angle of growth rings. The article evaluated properties of tension and normal wood before and after drying process. Properties which are monitored were moisture, moisture gradients, covering tests, colour changes and...
-
MEASUREMENT OF TEMPERATURE-DEPENDENT VISCOSITY AND THERMAL CONDUCTIVITY OF ALUMINA AND TITANIA THERMAL OIL NANOFLUIDS
PublicationIn this study results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublicationThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
Analysis of EN 1993-1-6 guidelines about determining amplitudes of equivalent imperfections of steel cylindrical shells subjected to uniform external pressure
PublicationCivil engineering structures should be designed with reference to relevant standards. One of them is a Eurocode 3 standard EN 1993-1-6:2007: Design of steel structures Part 1-6: Strength and Stability of Shell Structures. According to this standard, the value of buckling load can be determined using different approaches: classical hand calculations (stress design) and geometrical and material non-linear analysis of an imperfect...
-
A Convenient Way to Methylated 2-Imidazolines. Syntheses of Fluorene and Triazine Cyclic Diamidines
PublicationOne N-methyl- and 4-substituted 2-imidazolines are described. Fluorene bisimidazolines were obtained in good yield (64-92%), starting from 2,7-dicyanofluorene and ammonium sulfide. In a two-step procedure the crude bisthioamide was reacted with excess diaminoalkane-ethanol (1:1 mixt.) in an oil bath. This new procedure is superior over std. methods. For the sake of comparison, a new triazine bisimidazoline (I) was prepd. by...
-
Flexural buckling and post-buckling of columns made of aluminium alloy
PublicationThe paper concerns flexural buckling and initial post-buckling of axially compressed columns made of aluminium alloy described by the Ramberg-Osgood relationship. The non-linear differential equation of the problem is derived using the stationary total energy principle and the assumptions of classical beam theory within a finite range. The approximate analytical solution of the equation leading to the buckling loads and initial...
-
The distributed model predictive controller for the nuclear power plant turbo-generator set
PublicationTypically there are two main control loops with PI controllers operating at each turbo-generator set. In this paper a distributed model predictive controller DMPC, with local QDMC controllers for the turbine generator, is proposed instead of a typical PI controllers. The local QDMC controllers utilize step-response models for the controlled system components. These models parameters are determined based on the proposed black-box...
-
DYNAMIC POSITIONING CAPABILITY ASSESSMENT BASED ON OPTIMAL THRUST ALLOCATION
PublicationThe article presents an efficient method of optimal thrust allocation over the actuators in a dynamically positioned ship, according to the DNV-ST-0111 standard, Level 1. The optimisation task is approximated to a convex problem with linear constraints and mathematically formulated as quadratic programming. The case study is being used to illustrate the use of the proposed approach in assessing the DP capability of a rescue ship....
-
Multicriteria Evolutionary Weather Routing Algorithm in Practice
PublicationThe Multicriteria Evolutionary Weather Routing Algorithm (MEWRA) has already been introduced by the author on earlier TransNav 2009 and 2011 conferences with a focus on theoretical application to a hybrid-propulsion or motor-driven ship. This paper addresses the topic of possible practical weather routing applications of MEWRA. In the paper some practical advantages of utilizing Pareto front as a result of multicriteria optimization...
-
Wybrane aspekty modelowania uderzenia pojazdem dźwigara wiaduktu
PublicationW pracy przedstawiono różne zagadnienia związane z uderzeniem pojazdu w dźwigar wiaduktu. Omówiono wybór modelu obliczeniowego, na podstawie porównania wyników dla modelu dźwigara zespolonego, modelu dźwigara stalowego oraz modelu wiaduktu. Następnie opisano model dźwigara zespolonego zastosowany w analizie MES oraz metodę wyznaczania współczynników tłumienia Rayleigha. Symulację numeryczną uderzenia dźwigara wiaduktu przez koparkę...
-
Wykorzystanie klasyfikacji funkcjonalnej usług do efektywnego zarządzania zasobami chmurowymi
PublicationWykazano jak istotnym problemem jest zarzadzanie chmurą obliczeniową, w tym alokacja zasobów do wykonania usług (workloadów) zgłoszonych przez użytkownika. Przeanalizowano problem podziału usług wdrażanych w środowiskach chmurowych na klasy określające ich funkcjonalność. Zaproponowano oryginalną metodę alokacji workloadów wykorzystującą wprowadzoną klasyfikację funkcjonalną oraz identyfikację tych klas na podstawie wielkości generowanego...
-
Magdalena Szuflita-Żurawska
PeopleHead of the Scientific and Technical Information Services at the Gdansk University of Technology Library and the Leader of the Open Science Competence Center. She is also a Plenipotentiary of the Rector of the Gdańsk University of Technology for open science. She is a PhD Candidate. Her main areas of research and interests include research productivity, motivation, management of HEs, Open Access, Open Research Data, information...
-
On the Usefulness of the Generalised Additive Model for Mean Path Loss Estimation in Body Area Networks
PublicationIn this article, the usefulness of the Generalised Additive Model for mean path loss estimation in Body Area Networks is investigated. The research concerns a narrow-band indoor off-body network operating at 2.45 GHz, being based on measurements performed with four different users. The mean path loss is modelled as a sum of four components that depend on path length, antenna orientation angle, absolute difference between transmitting...
-
STRUCTURE AND MAGNETIC PROPERTIES OF Bi5Ti3FeO15 CERAMICS PREPARED BY SINTERING, MECHANICAL ACTIVATION AND EDAMM PROCESS. A COMPARATIVE STUDY
PublicationThree different methods were used to obtain Bi5Ti3FeO15 ceramics, i.e. solid-state sintering, mechanical activation (MA) with subsequent thermal treatment, and electrical discharge assisted mechanical milling (EDAMM). The structure and magnetic properties of produced Bi5Ti3FeO15 samples were characterized using X-ray diffraction and Mössbauer spectroscopy. The purest Bi5Ti3FeO15 ceramics was obtained by standard solid-state sintering...