Search
Filters
total: 1962
displaying 1000 best results Help
Search results for: ROAD VEHICLE NOISE
-
Comparing the Effectiveness of ANNs and SVMs in Forecasting the Impact of Traffic-Induced Vibrations on Building
PublicationTraffic - induced vibrations may cause damage to structural elements and may even lead to structural collapse. The aim of the article is to compare the effectiveness of algorithms in forecasting the impact of vibrations on buildings using the Machine Learning (ML) methods. The paper presents two alternative approaches by using Artificial Neural Networks (ANNs) and Support Vector Machines (SVMs). Factors that may affect traffic-induced...
-
The Idea of Using Bayesian Networks in Forecasting Impact of Traffic-Induced Vibrations Transmitted through the Ground on Residential Buildings
PublicationTraffic–induced vibrations may constitute a considerable load to buildings. In this paper, vibrations transmitted through the ground caused by wheeled vehicles are considered. This phenomenon may cause cracking of plaster, cracks in load-bearing elements or even, in extreme cases, collapse of the whole structure. Measurements of vibrations of real structures are costly and laborious. Therefore, the aim of the present paper is to...
-
Design of poroelastic wearing course with the use of direct shear test
PublicationPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
VEHICLE DYNAMICS (2024)
e-Learning Courses(W) Vehicle dynamics (W-Lecture) - DAPE - WIMiO The course entitled "Vehicle dynamcs" (VD) is conducted for the DAPE WIMiO Students. The VD course is to discuss the following problems: - major problems of vehicle dynamics from the application point of view, - definition of working environment, - types of vehicles, - parameters and characteristics of vehicles, - assessment of performance of vehicles towards design, -...
-
Marek Pszczoła dr hab. inż.
PeopleI am a Faculty member (Department of Highway and Transportation Engineering) at the Faculty of Civil and Environmental Engineering, Gdansk University of Technology, Poland). My main research interests include: low-temperature properties of asphalt mixtures, low temperature cracking assessment of pavement structures, road materials properties, thermal stress analysis, design of pavement structures, airfield design and analysis....
-
Impact of different car-following models on estimating safety and emissions on signal-controlled intersections using microscopic simulations
PublicationThis paper examines the influence of two selected car-following models on the outcomes of microscopic traffic simu-lations. The authors begin by reviewing the literature on the various traffic models, methods for estimating energy consumption, fuel use, and emissions. The authors discuss using surrogate safety measures derived from analysing vehicle trajectories in a microscopic traffic model to estimate safety levels. This paper...
-
ANALYSIS OF ROLLING RESISTANCE OF TIRES WITH RUN FLAT INSERT APPLYING DRUM METHOD AND RADIAL CHARACTERISTIC
PublicationThis paper presents analysis of rolling resistance of tires with RUN FLAT insert applying drum method and radial characteristic. The conducted studies indicated changes in operational properties of wheel, occurring as a result of inflation pressure drop in the wheel. As regards radial elasticity, such changes result in significant drop of radial rigidity and increase of static deflection and increase of tire rolling resistance....
-
Research on operational characteristics of tyres with run flat insert
PublicationThe paper describes results of research on heavy vehicle tyre with Run Flat VFI insert. The experiment has included the determination of heat generation, rolling resistanceand radial stifnessof two different tyre designes (textile and steel carcass). The results have been used for the purpose of ewalution of tyre operating characteristics. The study included research on non-inflated tyre properties. The purpose of the paper is...
-
Recent advances in traffic optimisation: systematic literature review of modern models, methods and algorithms
PublicationOver the past few decades, the increasing number of vehicles and imperfect road traffic management have been sources of congestion in cities and reasons for deteriorating health of its inhabitants. With the help of computer simulations, transport engineers optimise and improve the capacity of city streets. However, with an enormous number of possible simulation types, it is difficult to grasp valuable, innovative solutions which...
-
Finite Element Analysis of Occupant Risk in Vehicular Impacts into Cluster Mailboxes
PublicationThe deployment of cluster mailboxes (CMs) in the U.S. has raised safety concerns for passengers in potential vehicular crashes involving CMs. This study investigated the crashworthiness of two types of CMs through nonlinear finite element simulations. Two configurations of CM arrangements were considered: a single- and a dual-unit setup. These CM designs were tested on flat-road conditions with and without a curb. A 2010 Toyota...
-
Investigation of Acoustic Properties of Poroelastic Asphalt Mixtures in Laboratory and Field Conditions
PublicationMeasures for the improvement of acoustic conditions in the vicinity of roads include the construction of pavement structures with low-noise surfaces with optimal macrotexture and the highest possible sound absorption coefficient. Laboratory evaluation of acoustic properties of a designed asphalt mixture before its placement in the pavement is a good solution. Currently, the most popular method for the determination of the sound...
-
Road Materials and Pavement Design
Journals -
FLUCTUATION AND NOISE LETTERS
Journals -
Investigating the Effects of Ground-Transmitted Vibrations from Vehicles on Buildings and Their Occupants, with an Idea for Applying Machine Learning
PublicationVibrations observed as a result of moving vehicles can potentially affect both buildings and the people inside them. The impacts of these vibrations are complex, affected by a number of parameters, like amplitude, frequency, and duration, as well as by the properties of the soil beneath. These factors together lead to various effects, from slight disruptions to significant structural damage. Occupants inside affected buildings...
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublicationPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Investigation method of large-volume tire with mobile test rig
PublicationThe goal of this research is to develop the tire test method and mobile tire test rig. The test rig enables measurement of tire properties as stiffness and viscous damping in vertical direction, and tire–ground characteristics on the asphalt rigid surface. The tire-ground characteristics are measured by force and a torque measurement hub. The design, calibration and the algorithm for calculating the forces in the wheel center are...
-
Algorithm for Automatic Wear Estimation of Railway Contact Strips Based on 3D Scanning Results
PublicationElectric rail vehicles use current collection system which consists of overhead contact line and a current collector (pantograph) mounted on the roof of a vehicle. A pantograph is equipped with contact strips, which slide along the contact wire, ensuring steady electric contact. Contact strips are made of carbon layer, fixed to an aluminum carrier. The carbon layer wears down due to friction. Using overly worn contact strips increases...
-
Identification of Optocoupler Devices with RTS Noise
PublicationThe results of noise measurements in low frequency range for CNY 17 type optocouplers are presented. The research were carried out on devices with different values of Current Transfer Ratio (CTR). The methods for identification of Random Telegraph Signal (RTS) in noise signal of optocouplers were proposed. It was found that the Noise Scattering Pattern method (NSP method) enables to identify RTS noise as non-Gaussian component...
-
The innovative approach for using pavement as a fire prevention measure in tunnels
PublicationThe paper consists of two main parts: first presents study regarding the typically used pavement structures in tunnels and the second part: the first fire trials of the poroelastic SEPOR (Safe, Eco-friendly POroelastic Road Surface) mixture which was designed to be used among other uses in tunnels. In the first part of the paper different pavement materials, such as cement concrete, asphalt concrete, stone mastic asphalt and porous...
-
Impact evaluation of a cycling promotion campaign using daily bicycle counters data: The case of Cycling May in Poland
PublicationThe promotion of active and sustainable transport modes as an alternative to motorised individual transport has become a key policy priority in Europe, to reduce air pollution, road congestion, noise, traffic injuries, and the adverse health outcomes of sedentary lifestyles. Policymakers are implementing a wide range of measures to encourage this shift in attitudes and behaviours. These interventions are most valuable when targeting...
-
Energy Management for PV Powered Hybrid Storage System in Electric Vehicles Using Artificial Neural Network and Aquila Optimizer Algorithm
PublicationIn an electric vehicle (EV), using more than one energy source often provides a safe ride without concerns about range. EVs are powered by photovoltaic (PV), battery, and ultracapacitor (UC) systems. The overall results of this arrangement are an increase in travel distance; a reduction in battery size; improved reaction, especially under overload; and an extension of battery life. Improved results allow the energy to be used efficiently,...
-
Online urban acoustic noise monitoring system
PublicationConcepts and implementation of the Online Urban Noise Monitoring System are presented. Principles of proposed solution used for dynamic acoustical maps creating are discussed. The architecture of the system and the data acquisition scheme are described. The concept of noise mapping, based on noise source model and propagation simulations, was developed and employed in the system. Dynamic estimation of noise source parameters utilized...
-
Urban and Road Engineering - Smolnicki
e-Learning CoursesLectures about "Urban and Road Engineering", dedicated to sixth semester of the English-speaking group, will be conducted in a way that activates students. Lectures on Road Engineering cover a wide range of important issues related to the subject, starting from a discussion of the historical circumstances of the creation, development and domination of the contemporary conventional model, through identifying new approaches and...
-
Frequently updated noise threat maps created with use of supercomputing grid
PublicationAn innovative supercomputing grid services devoted to noise threat evaluation were presented. The services described in this paper concern two issues, first is related to the noise mapping, while the second one focuses on assessment of the noise dose and its influence on the human hearing system. The discussed services were developed within the PL-Grid Plus Infrastructure which accumulates Polish academic supercomputer centers....
-
Detection of the Incoming Sound Direction Employing MEMS Microphones and the DSP
PublicationA 3D acoustic vector sensor based on MEMS microphones and its application to road traffic monitoring is presented in the paper. The sensor is constructed from three pairs of digital MEMS microphones, mounted on the orthogonal axes. Signals obtained from the microphones are used to compute sound intensity vectors in each direction. With this data, it is possible to compute the horizontal and vertical angle of an incoming sound....
-
A study of nighttime vehicle detection algorithms
Open Research DataThis dataset is from my master's thesis "A study of nighttime vehicle detection algorithms". It contains both raw data and preprocessed dataset ready to use. In the pictures below you can see how images were annotated.
-
Tire camber angle influence on tire-pavement noise
PublicationTaking into account tire-pavement noise and tires classification with respect to noise emission special measurement methods are usually used. When two of them are applied (the Laboratory Drum Method (DR) and the Close-Proximity Method (CPX)) the investigator has to be sure that the position of the tire is correct. The authors of this paper thought about tire position as tire (wheel) alignment in particular tire camber angle. They...
-
Sensors and System for Vehicle Navigation
PublicationIn recent years, vehicle navigation, in particular autonomous navigation, has been at the center of several major developments, both in civilian and defense applications. New technologies, such as multisensory data fusion, big data processing, or deep learning, are changing the quality of areas of applications, improving the sensors and systems used. Recently, the influence of artificial intelligence on sensor data processing and...
-
Evaluation of excessive noise effects on hearing employing psychoacoustic dosimetry
PublicationResearch results regarding the noise impact on hearing applying the concept of the Psychoacoustic Noise Dosimetry (PND) are presented. The general characteristics of the PND algorithm are discussed. Additionally, the results of hearing examinations conducted in the laboratory conditions are shown. The main objective of the research was to determine the time needed for the Temporary Threshold Shift to reverse. The results were used...
-
Old-timer Vehicle - Braking Efficiency Measurement at Vehicle Inspection Stations and Roadworthiness Validity Certificate.
PublicationObtaining the Roadworthiness Validity Certificate for an old-timer vehicle involves an appropriate test performance, namely, "Old-timer Vehicle Technical Specification Compliance Test". It seems obvious that this kind of test should include a considerable checklist, however, the current legal regulations connected with this test are not specific enough. One of the certificates issued on this test results is "Old-timer Vehicle Technical...
-
MONITORING SYSTEM OF THE ROAD EMBANKMENT
PublicationThe paper presents the analysis of the monitoring system of the embankment supported on concrete columns and overlaid by a load transfer platform with the embedded steel grid. This field investigation was to study the complex interaction among the columns, the load transfer platform layer, and steel grid via in situ measurements during erection and live loading of the embankment. The study was focused on the behaviour of steel...
-
Determining the noise impact on hearing using psychoacoustical noise dosimeter
PublicationThis research study presents the designed noise dosimeter based on psychoacoustical properties of the human hearing system and, at the same time. evaluation of time and frequency characteristics of noise. The designed noise dosimeter enables assessing temporary threshold shift (TTS) in critical hands in real time. In this way it is possible monitoring the hearing threshold shift continuously for people who stay in the harmful noise...
-
Road safety inspection as a tool for road safety management – the polish experience
PublicationIn Poland, road inspections were implemented in June 2014 on all national roads. Previously conducted traffic surveys mainly related to the technical condition of roads, signs and markings; other safety issues were overlooked. The main problem that occurs during inspection is an inspector’s subjective qualitative assessment which affects the classification of the sources of hazard on the road.. The paper presents an analysis of...
-
Noise & Health
Journals -
A Simplified Method of Trend Removal to Determine Noise Observed During a Supercapacitor’s Discharging
PublicationIn this paper, new method of trend removal is proposed. This is a simplified method based on Empirical Mode Decomposition (EMD). The method was applied for voltage time series observed during supercapacitor discharging process. It assured the determination of an additive noise component after subtracting the identified trend component. We analyzed voltage time series observed between the terminals of the supercapacitor when discharged...
-
Baltic Journal of Road and Bridge Engineering
Journals -
Vehicle classification based on soft computing algorithms
PublicationExperiments and results regarding vehicle type classification are presented. Three classes of vehicles are recognized: sedans, vans and trucks. The system uses a non-calibrated traffic camera, therefore no direct vehicle dimensions are used. Various vehicle descriptors are tested, including those based on vehicle mask only and those based on vehicle images. The latter ones employ Speeded Up Robust Features (SURF) and gradient images...
-
A method of RTS noise identification in noise signals of semiconductor devices in the time domain
PublicationIn the paper a new method of Random Telegraph Signal (RTS) noise identification is presented. The method is based on a standardized histogram of instantaneous noise values and processing by Gram-Charlier series. To find a device generating RTS noise by the presented method one should count the number of significant coefficients of the Gram-Charlier series. This would allow to recognize the type of noise. There is always one (first)...
-
MEASUREMENT OF NOISE IN SUPERCAPACITORS
PublicationA developed method and measurement setup for measurement of noise generated in a supercapacitor is presented. The requirements for noise data recording are considered and correlated with working modes of supercapacitors. An example of results of low-frequency noise measurements in commercially available supercapacitors are presented. The ability of flicker noise measurements suggests that they can be used to assess quality of tested supercapacitors.
-
An automatic system for identification of random telegraph signal (RTS) noise in noise signals
PublicationIn the paper the automatic and universal system for identification of Random Telegraph Signal (RTS) noise as a non-Gaussian component of the inherent noise signal of semiconductor devices is presented. The system for data acquisition and processing is described. Histograms of the instantaneous values of the noise signals are calculated as the basis for analysis of the noise signal to determine the number of local maxima of histograms...
-
Performance Analysis of the "Intelligent" Kirchhoff- Law - Johnson-Noise Secure Key Exchange
PublicationThe Kirchhoff-law - Johnson-noise (KLJN) secure key distribution system provides a way of exchanging theoretically secure keys by measuring random voltage and current through the wire connecting two different resistors at Alice’s and Bob’s ends. Recently new advanced protocols for the KLJN method have been proposed with enhanced performance. In this paper, we analyze the KLJN system and compare with the „intelligent” KLJN (iKLJN)...
-
Noise measurements on low noise pavements - problems with inhomogeneity of wearing course
PublicationDuring the last several years, when performing numerous CPX noise measurements on low noise pavements,significant inhomogeneity of the wearing course was observed in numerous cases. Similar problems were almost not existing regarding to the dense pavements.In general three main reasons of inhomogeneity can be defined. The first one are imperfections in technology of production of a asphalt mix or/and errors made already during...
-
Modelling of performance of an AUV stealth vehicle. Design for operation.
PublicationIn the paper some results of research connected with modelling of performance and risk assessment of an AUV stealth vehicle are presented. A general approach to design of the stealth AUV autonomous underwater vehicle under consideration is introduced. The basic stealth characteristics of the AUV stealth vehicle are briefly described. The method of research is introduced. The AUV stealth vehicle concept is presented including the...
-
Modeling of performance of an AUV stealth vehicle. Design for operation.
PublicationIn the paper some results of research connected with modelling of performance and risk assessment of an AUV stealth vehicle are presented. A general approach to design of the stealth AUV autonomous underwater vehicle under consideration is introduced. The basic stealth characteristics of the AUV stealth vehicle are briefly described. The method of research is introduced. The AUV stealth vehicle concept is presented including the...
-
The noise macromodel of an optocoupler including 1/(f^alfa) noise source
PublicationThe course of design of an optocoupler's PSpice macromodel including noise sources is described. The PSpice macromodel is proposed for the low frequency range. The PSpice model of a MOSFET transistor was applied as the noise source type 1/(f^alfa) in an optocoupler PSpice macromodel. In the enhanced macromodel the value of an exponent α can be changed in the range of 0.8 - 1.25.
-
Assessing vehicle restraint systems on horizontal curves
PublicationHorizontal curves, an element of road infrastructure, have a statistically high number of accidents. Considering that horizontal curves in the last ten years have had app. 10% of all road accidents representing app. 14% of all fatalities on Polish roads, the issue is serious and requires more research and proper road safety treatments. Data for 2007 - 2016 show that in the case of accidents on horizontal curves app. 45% of the...
-
Influence of IED Explosion on Lateral Dynamics of a Vehicle
PublicationThe paper describes field test results of heavy vehicle tire blow-outs. Both civilian and military vehicles are subjected to sudden loss of inflation pressure in one or more wheels, often accompanied by serious tire damage. Selected results related to the lateral dynamic of vehicle during and just after explosive tire destruction are reported
-
Road Infrastructure Safety Management in Poland
PublicationThe objective of road safety infrastructure management is to ensure that when roads are planned, designed, built and used road risks can be identified, assessed and mitigated. Road transport safety is significantly less developed than that of rail, water and air transport. The average individual risk of being a fatality in relation to the distance covered is thirty times higher in road transport that in the other modes. This is...
-
The Methods for RTS Noise Identification
PublicationIn the paper authors present two methods, which allows to identify the RTS noise in noise signal of semiconductor devices. The first one was elaborated to identify the RTS noise and also to estimate the number of its levels. The second one can be used to estimate all of the parameters of Gaussian and non-Gaussian components in the noise signal in a frequency domain.
-
Modeling of Combined Phenomena Affecting an AUV Stealth Vehicle
PublicationIn the paper some results of research connected with modelling the basic stealth characteristics of an AUV vehicle are presented. First of all a general approach to design of the stealth AUV autonomous underwater vehicle under consideration is introduced. Then, the AUV stealth vehicle concept is briefly described. Next a method of modelling of the stealth characteristics is briefly described as well. As an example of the stealth...