Filters
total: 2807
-
Catalog
displaying 1000 best results Help
Search results for: ADAPTIVE NUMERICAL SCHEME
-
NUMERICAL MODELLING AND EXPERIMENTATION OF HISTORICAL CARPENTRY CORNER LOG JOINTS
PublicationThe main purpose of this research is to determine the stress distributions on the contact surfaces between the logs of the historical carpentry corner joints. The additional purpose is to compare the stress distribution for four different boundary conditions in the case of dry and wet pine wood. The paper presents the results of numerical analysis of the shortcorner dovetail connection and the saddle notch corner joint, which are...
-
Experimental and numerical analysis of wave propagation in ground anchors
PublicationThe article focuses on wave propagation phenomenon in ground anchors. The main aim of the investigation is the non-destructive diagnostics and the assessment of the state of ground anchors, using the guided wave propagation method. Laboratory models of anchors with different lengths of the anchor body were tested and voltage signals of propagating waves were registered at several locations. For all tested specimens corresponding...
-
Application of the numerical-analytic method for systems of differential equations with parameter
PublicationThe numerical-analytic method is applied to systems of differential equations with parameter under the assumption that the corresponding functions satisfy the Lipschitz conditions in matrix notation. We also obtain several existence results for problems with deviations of an argument
-
Numerical analysis of elastic wave propagation in unbounded structures
PublicationThe main objective of this paper is to show the effectiveness and usefulness of the concept of an absorbing layer with increasing damping (ALID) in numerical investigations of elastic wave propagation in unbounded engineering structures. This has been achieved by the authors by a careful investigation of three different types of structures characterised by gradually increasing geometrical and mathematical description complexities....
-
Balance error generated by numerical diffusion in the solution of Muskingum equation
PublicationIn the paper the conservative properties of the lumped hydrological models with variable parameters are discussed. It is shown that in the case of the non-linear Muskingum equation the mass balance is not satisfied. The study indicates that the mass balance errors are caused by the improper form of equation and by the numerical diffusion which is generated in the solution. It has been shown that the classical way of derivation...
-
Experimental and numerical analysis of an aluminum cantilevered beam with polymer adhesive
PublicationIn this paper, experimental and numerical investigation on a composite cantilevered aluminum beam has been conducted. The subject of the study consists of two plain aluminum elements bonded with polymer adhesive of different thickness. It has been proven in the previous study that this kind of material has high damping properties. During an experimental investigation, value of damping ratios have been obtained. The aim of a numerical...
-
Numerical and Clinical Analysis of an Eyeball Injuries under Direc Impact
PublicationObjectives: The objective of this study was to develop a numerical model of the eyeball and orbit to simulate a blunt injury to the eyeball leading to its rupture, as well as to conduct a comparative analysis of the results obtained using the finite element method against the clinical material concerning patients who had suffered an eyeball rupture due to a blunt force trauma. Material and Methods: Using available sclera biometric and...
-
A numerical and experimental analysis of multi-hole orifice in turbulent flow
PublicationIn this research study, the comprehensive metrological analysis is investigated for a 4-hole orifice with module m = 0.25 installed in the pipeline with an internal diameter of 50 mm. A detailed numerical simulation was performed for the turbulence models: k-ε-realizable and k-ω-BSL. The novelties of the research include model validation by comparing the results of numerical studies with the experiment conducted in the area of...
-
Numerical simulation of screw displacement pile interaction with non-cohesive soil
PublicationA trial numerical simulation of screw displacement pile interaction with non-cohesive subsoil during the transfer of compression load. The simulation was carried out in an axisymmetric system. The technological phases of pile installation in the ground were numerically modelled using equivalent processes which provided similar effects to real technical actions. The results of the numerical calculations were verified by comparing...
-
Optimization algorithm and filtration using the adaptive TIN model at the stage of initial processing of the ALS point cloud
PublicationAirborne laser scanning (ALS) provides survey results in the form of a point cloud. The ALS point cloud is a source of data used primarily for constructing a digital terrain model (DTM). To generate a DTM, the set of ALS observations must be first subjected to the point cloud processing methodology. A standard methodology is composed of the following stages: acquisition of the ALS data, initial processing (including filtration),...
-
COMMUNICATIONS IN NUMERICAL METHODS IN ENGINEERING
Journals -
Journal of Numerical and Applied Mathematics
Journals -
ELECTRONIC TRANSACTIONS ON NUMERICAL ANALYSIS
Journals -
IMA JOURNAL OF NUMERICAL ANALYSIS
Journals -
Numerical Algebra Control and Optimization
Journals -
NUMERICAL FUNCTIONAL ANALYSIS AND OPTIMIZATION
Journals -
Journal of Applied and Numerical Optimization
Journals -
NUMERICAL LINEAR ALGEBRA WITH APPLICATIONS
Journals -
SIAM JOURNAL ON NUMERICAL ANALYSIS
Journals -
Teaching Adaptive Control with DS1102 DSP Controller Board
Publication -
Adaptive selection of control parameters in differential evolution algorithms
PublicationW pracy przedstawiono metodę adaptacyjnej selekcji parametrów kontrolnych w różnicowych algorytmach ewolucyjnych. Wartości parametrów takich jak: stopień krzyżowania i współczynnik różnicowej mutacji są odpowiednio zmieniane. Funkcje testowe użyte do testowania proponowanej metody były zaczerpnięte z literatury. Rezultaty uzyskane przy użyciu opisanej metody zostały porównane z innymi metodami selekcji różnicowej. Wyniki te, uzyskane...
-
GaMRed – adaptive filtering of high-throughput biological data
Publication -
Adaptive resolution-constrained scalar multiple-description coding
Publication -
Tunable broadband integrated circuits for adaptive optical interconnects
Publication -
Gradient adaptive lattice filter in FPGAS-implementation issues
Publication -
Generalized adaptive notch filter with a self-optimization capability
PublicationW pracy przedstawiono samonastrajalny wariant tzw. uogólnionego adaptacyjnego filtru wycinającego. Automatycznym strojeniem objęte są dwa współczynniki wzmocnienia adaptacji, odpowiedzialne za śledzenie amplitud i częstotliwości parametrów identyfikowanego obiektu.
-
Adaptive neural voltage controller with tunable activation gain
PublicationW artykule przedstawiono model adaptacyjnego neuronowego regulatora napięcia dla turbogeneratora z nastrojonym współczynnikiem wzmocnienia funkcji przynależności. Ten model jest kombinacją klasycznego neuronowego modelu i neuronowego modelu z współczynnikiem wzmocnienia funkcji przynależności zależnym od warunków pracy obiektu.Przedstawiono, także wyniki symulacji mające na celu badania efektywności proponowanego regulatora dla...
-
Adaptive response of microbial communities to soluble microbial products.
PublicationBadano wpływ obecności ubocznych produktów mikroorganizmów na stężenie biomasy osadu czynnego oraz na efektywność obniżenia ładunku BZT5 i ChZT w ściekach syntetycznych. Doświadczenia prowadzono w obecności ubocznych produktów mikroorganizmów (Soluble Microbial Products) oraz w warunkach pozbawionych tych produktów.
-
Targed tracking with adaptive fusionof multiple sensor measurements.
PublicationW pracy przedstawiono metodę adaptacyjnej selekcji pomiarów z wielu radarów wykorzystywanych w procesie integracji pomiarów dla śledzenia obserwowanego obiektu. W przypadku dużego zróżnicowania dokładności pomiarów pochodzących z różnych radarów, rezultaty integracji pomiarów nie różnią się znacząco od wyników śledzenia opartego na pomiarach z najbardziej dokładnego źródła.
-
Adaptive acoustic crosstalk cancellation in mobile computer device
PublicationThe cancellation of acoustic crosstalk is employed to enhance the stereo image in mobile listening conditions. A practical setup employing a mobile computer is employed. The adaptation of the crosstalk cancellation filter to the position of the listener's head is featured. The measurement evaluating the possibility of practical application of the method are described. The head and torso simulator was used for measurements. The...
-
Semi-adaptive feedback active control of MRI noise
PublicationA feedback controller is proposed for cancellation of magnetic resonance imaging (MRI) noise. The design of the controller takes into account specific features of the MRI noise signal. Simulation results show that a considerable rejection rate of the MRI noise can be obtained.
-
DEVELOPMENT OF A COUPLED NUMERICAL AND EXPERIMENTAL APPROACH TO HYDRODYNAMIC NOISE ESTIMATION
PublicationThe hydroacoustic signature of ships' propellers can be estimated experimentally through measurements of cavitation-induced pressure fluctuations and the corresponding noise distributions at model scale. These measurements need to be performed in a cavitation tunnel under the propellers operating conditions and are quite sensitive and challenging to perform with sufficient accuracy. In comparison, the numerical approach can be...
-
Experimental study and numerical simulation of the dynamic penetration into dry clay
PublicationTests of dry clay were carried out in a uniaxial stress state using the experimental setup which implements the split Hopkinson pressure bar method. Based on the results of these experiments, the compressive strength of clay was determined as an important element of S.S. Grigoryan’s model of the soil medium. In addition, the parameters of this model are determined from the results of experiments using the modified Kolsky method...
-
Numerical Analysis of TB32 Crash Tests for 4-cable Guardrail Barrier System Installed on the Horizontal Convex Curves of Road
PublicationHorizontal curves are one of the elements of road infrastructure where statistically a relatively high number of accidents have been reported. In the last ten years in Poland approx. 10% of all road accidents happened on horizontal curves of roads and was responsible for approx. 14% of all fatalities on Polish roads. Thus, this issue is important and requires extensive research and proper road safety treatments. One possible measure...
-
Robert Piotrowski dr hab. inż.
PeopleRobert Piotrowski jest absolwentem Wydziału Elektrotechniki i Automatyki (2001r., kierunek: Automatyka i Robotyka) oraz Wydziału Zarządzania i Ekonomii (2002r., kierunek: Organizacja Systemów Produkcyjnych) Politechniki Gdańskiej. Od 2005 roku jest zatrudniony na Wydziale Elektrotechniki i Automatyki, aktualnie w Katedrze Inteligentnych Systemów Sterowania i Wspomagania Decyzji. W 2005 roku obronił rozprawę doktorską (Automatyka...
-
Kinetic flux vector splitting scheme for solving non-reactive multi-component flows
Publication -
Capacity efficient shared protection and fast restoration scheme in self-configured optical networks
PublicationW artykule zaproponowano nową koncepcję optymalizacji rozdziału zasobów dla przeżywalnych sieci rozległych, która gwarantuje szybkie odtwarzanie usług po wystąpieniu awarii. Wykazano, iż proponowany algorytm, wykorzystujący ideę wierzchołkowego kolorowania grafów, nie powoduje wydłużania ścieżek zabezpieczających - zjawiska charakterystycznego dla powszechnie stosowanych algorytmów optymalizacji. Udowodniono, iż powyższa cecha...
-
A fast high-resolution 3-D Finite Difference Time-Domain scheme with macromodels.
PublicationZaprezentowano szybki trójwymiarowy wysokorozdzielczy algorytm różnic skończonych w dziedzinie czasu. Zwiększona rozdzielczość osiągnięta została poprzez połączenie standardowego schematu FDTD z makromodelami silnie zagęszczonych objętości stworzonych przez zastosowanie redukcji rzędu modelu. Nowy schemat FDTD z makromodelami jest wyprowadzony. Koszt numeryczny nowej metody jest wyestymowany. Doskonałe wyniki zostały zaobserwowane...
-
Numerical analysis on axial capacity of steel built-up battened columns
PublicationThis paper deals with the numerical analysis aimed at study the bearing capacity of pinended steel built-up columns under axial compression. Finite element (FE) models were performed for the columns presented in the literature. The main problem discussed in the article is the shape and magnitude of geometric imperfections introduced into the numerical FE model, necessary to obtain the load capacity consistent with the experimental...
-
Numerical Modelling of Forced Convection of Nanofluids in Smooth, Round Tubes: A Review
PublicationA comprehensive review of published works dealing with numerical modelling of forced convection heat transfer and hydrodynamics of nanofluids is presented. Due to the extensive literature, the review is limited to straight, smooth, circular tubes, as this is the basic geometry in shell-and-tube exchangers. Works on numerical modelling of forced convection in tubes are presented chronologically in the first part of the article....
-
Adaptive Dynamical Systems Modelling of Transformational Organizational Change with Focus on Organizational Culture and Organizational Learning
PublicationTransformative Organizational Change becomes more and more significant both practically and academically, especially in the context of organizational culture and learning. However computational modeling and a formalization of organizational change and learning processes are still largely unexplored. This paper aims to provide an adaptive network model of transformative organizational change and translate a selection of organizational...
-
Adaptive Dynamical Systems Modelling of Transformational Organizational Change: with Focus on Organizational Culture and Organizational Learning
PublicationTransformative Organizational Change becomes more and more significant both practically and academically, especially in the context of organizational culture and learning. However computational modeling and a formalization of organizational change and learning processes are still largely unexplored. This paper aims to provide an adaptive network model of transformative organizational change and translate a selection of organizational...
-
Numerical analysis of mechanical properties of an infill structure used in 3D printings
PublicationThe paper presents results of a numerical analysis focused on an identification of mechanical properties of an element created by using Fused Deposition Modelling additive manufacturing technique (FDM). There is presented a description of technology of the 3D printing, numerical model created by using the finite element method (FEM), as well as some problems referred to estimation of the mechanical properties of the printout. The...
-
Footbridges, numerical aproach
PublicationW artykule zamieszczono przegląd symulacji numerycznych kładek dla pieszych. Został on podzielony na trzy części(modele MES, obciążenie tłumem, odpowiedź mostu).
-
A numerical analysis of the thermal effects in the jet impingement stagnation zone
PublicationMost of the flows occurring in the engineering systems are turbulent and their accurate numerical analysis is still challenging, especially when combined with the heat transfer. One of the methods of heat transfer enhancement is utilization of the turbulent impinging jets, which were recently applied also in the heat exchangers. Their positive impact on the heat transfer performance was proven, but many questions related to its...
-
Experimental study and numerical optimization of tensegrity domes – A case study
PublicationThe paper deals with the design, experimental analysis and numerical optimization of tensegrity dome models. Two structures are analyzed – a Geiger system dome (preliminary dome), with PVC-U bars and PA6/PP/PET tendons and a Fuller system dome (target dome), with wooden bars and steel cables as tendons. All used materials are experimentally tested in terms of Young's modulus and yield stress values, the compressed bars are also...
-
Numerical Test for Stability Evaluation of Discrete-Time Systems
PublicationIn this paper, a new numerical test for stability evaluation of discrete-time systems is presented. It is based on modern root-finding techniques at the complex plane employing the Delaunay triangulation and Cauchy's Argument Principle. The method evaluates if a system is stable and returns possible values and multiplicities of unstable zeros of the characteristic equation. For state-space discrete-time models, the developed test...
-
Numerical modeling of GPR field in damage detection of a reinforced concrete footbridge
PublicationThe paper presents a study on the use of the ground penetrating radar (GPR) method in diagnostics of a footbridge. It contains experimental investigations and numerical analyses of the electromagnetic field propagation using the finite difference time domain method (FDTD). The object of research was a reinforced concrete footbridge over a railway line. The calculations of the GPR field propagation were performed on a selected cross-section...
-
Experimental and Numerical Investigations of the Effect of Curing Conditions on the Temperature Rise of Concrete
PublicationThis paper presents experimental and numerical studies investigating the impact of three curing conditions on temperature evolution in concrete cubes. The tests were performed on samples of the same volume (3.375 dm3) under different curing conditions: room temperature, insulation boxes, and adiabatic calorimeter. Various cements (Portland cement, Portland composite cement, and blast furnace slag cement) and aggregates (gravel...
-
Comparative Analysis of Numerical and Experimental Studies of the Airflow Around the Sample of Urban Development
PublicationIn this paper, on the background of a short overview of the recent advances in the field of Environmental Wind Engineering (EWE), a comparison of wind tunnel experiment and numerical simulation for some cases of airflow around an urban layout have been reported. The purpose of the study is quantitative and qualitative comparison of measurements in the wind tunnel as well as numerical simulation using Ansys Fluent software. The...