Filters
total: 2887
filtered: 2219
displaying 1000 best results Help
Search results for: POROELASTIC LAYER
-
Engineering Au nanoparticle arrays on SiO2 glass by pulsed UV laser irradiation
PublicationWe study semi-regular arrays of Au nanoparticles (NP) obtained via UV laser irradiation of thin Au films on glass substrate. The NP structures are prepared from films of a thickness up to 60 nm produced by discharge sputtering or pulsed laser deposition, and annealed by nanosecond laser pulses at 266 or 308 nm, respectively, at fluencies in the range of 60-410 mJ/cm2. For the rare- and close-packed NP structures, consistent description...
-
Comparision of mechanical properties of nitrided cases and remelted layers of austenitic stainless steel
Publication -
Preparation of porous TiO2 films by means of pulsed laser deposition for photocatalytic applications
PublicationIn this work the preparation and structure properties of porous thin films of TiO2 were investigated. The films were produced by means of the pulsed laser deposition technique using laser pulses at 266nm (10Hz) and at fluencies of 1-3.5J/cm2. The process was performed in vacuum using O2 buffer gas and films were deposited on the SiO2 glass or Si substrate. X-ray diffraction (XRD) and Raman analysis of the structure and chemical...
-
Measurement of sub-nanometer molecular layers with ISFET without a reference electrode dependency
PublicationA new method of detection and measurement with sub-nanometer resolution of layers adsorbed or bonded to the ISFET's gate dielectric was presented. The sensitivity of this method is high enough to detect even partial mono-layer covering. The transconductance measurement of the ISFET provides independence of the output signal from pH changes and the driving electrode electrochemical potential instabilities. The stable reference electrode...
-
Chemical, thermal and laser processes in recycling of photovoltaic silicon solar cells and modules
PublicationIn recent years, photovoltaic power generation systems have been gaining unprecedented attention as an environmentally beneficial method to solve the energy problem. From the economic point of view the pure silicon, which can be recapture from the used cells, is the most important material due to its cost and shortage. In the paper selected methods of used or damaged module and cells recycling and experimental results are presented....
-
Laser Investigations of Flow Patterns in Electrostatic Precipitators and Non Thermal Plasma Reactors
Publication -
Problems of analysis of axially loaded steel behavior under laser welded panel
PublicationWprowadzanie do praktyki nowych rozwiązań konstrukcyjnych wymaga posiadania danych wejściowych do procesu modelowania ich zachowania. Takim nowym elementem jest stalowy, spawany laserowo panel typu sandwich. W pracy pokazano wy-brane problemy towarzyszące modelowaniu zachowań takiej struktury. Pokazano podstawy teoretyczne wyznaczania sztyw-ności panelu a następnie omówiono wyniki badań wyboczenio-wych serii modeli o zmiennej geometrii.
-
Prosthetic Elements Made of the Ti-13Zr-13Nb Alloy by Selective Laser Melting
PublicationThe fabrication of the prosthetic foundations and bridges from the Ti-13Zr-13Nb alloy is described. The process was started from CAD/CAM design of 3D models of the foundations based on scanning of patient`s mouth. Next, 3D models were transformed into *.stl files for the manufacturing stage and then the manufacturing process by means of the selective laser melting with the SLM Realizer 100 equipment was made. The intrinsic structure...
-
Assessing Acute Toxicity of Selected Packages Internal Layers Extracts using Microtox®
PublicationIn the scientific literature related to the widely understood issue of packaging materials designed to have contact with food (food contact materials), there is much information on raw materials used for their production, as well as their physiochemical properties, types and parameters. Unfortunately, not much attention is given to the issues concerning migration of toxic substances from packaging and its actual influence on the...
-
Influence of Laser Modification on the Surface Character of Biomaterials: Titanium and Its Alloys—A Review
PublicationLaser surface modification is a widely available and simple technique that can be applied to different types of materials. It has been shown that by using a laser heat source, reproducible surfaces can be obtained, which is particularly important when developing materials for medical applications. The laser modification of titanium and its alloys is advantageous due to the possibility of controlling selected parameters and properties...
-
The interaction of the pulsed laser irradiation with titania nanotubes - Theoretical studies on the thermal effect
PublicationThis paper reports temperature dispersion simulations of titania nanotubes irradiated by the 355 nm, pulsed, nanosecond laser. The modelling with the use of Finite Elements Method concerns titania nanotubes of the length and the wall thickness in the range of 0.5–2 μm and 5–20 nm, respectively. The uniqueness of the morphology was preserved by ensuring the wall thickness variation along the height of the tube, which was determined...
-
Review on robust laser light interaction with titania – Patterning, crystallisation and ablation processes
PublicationTitanium dioxide is regarded as a very promising semiconducting material that is widely applied in many everyday-use products, devices, and processes. In general, those applications can be divided into energy or environmental categories, where a high conversion rate, and energy and power density are of particular interest. Therefore, many efforts are being put towards the elaboration of novel production routes, and improving the...
-
Microstructure and mechanical properties of laser surface-treated Ti13nb13zr alloy with MWCNTs coatings
PublicationLaser surface modification of titanium alloys is one of the main methods of improving the properties of titanium alloys used in implantology. This study investigates the microstructural morphology of a laser-modified surface layer on a Ti13Nb13Zr alloy with and without a carbon nanotube coating deposited by electrophoretic deposition. Laser modification was performed for samples with and without carbon nanotube coating for two...
-
Advancements in the Additive Manufacturing of Magnesium and Aluminum Alloys through Laser-Based Approach
PublicationComplex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives such as reduced part numbers, greater functionality, and lightweight, among others. Polymers, metals, and ceramics are the few materials that can be used in AM technology, but metallic materials (Magnesium and Aluminum) are attracting more attention from the research and industrial point of view. Understanding the role...
-
Impact of laser beam welding on mechanical behaviour of 2.25Cr–1Mo (P22) steel
PublicationThe use of welding processes in the manufacturing and repair of structures intended for the energy industry plays a key role in the guarantee of a continuous supply of fossil fuels, which is the basic condition for ensuring energy security. A square butt joint of 10 mm thick plate of 2.25Cr–1Mo (P22) steel was fabricated by autogenous laser beam welding process and then post-weld heat treatment (PWHT) for two sets of process parameters...
-
Capacity of Surface Production of Band Sawing in Manufacture of Oak Floor Upper Layers
PublicationThin lamellae, corresponding to the layer components of structural glued members, i.e., 2-ply or 3-ply glued flooring, can be manufactured in re-sawing operations of kiln-dried wood blocks or in wet technologies, which currently seem to be more common because of the shorter drying time. The re-sawing process in wet technology is conducted on dedicated thin-cutting band sawing machines with stellite-tipped band saws. The goal of...
-
Effect of Laser Treatment on Intrinsic Mechanical Stresses in Titanium and Some of Its Alloys
PublicationLaser surface treatment conducted at different power levels is an option to modify titanium bone implants to produce nano- and microtopography. However, such processing can lead to excess mechanical stress within the surface layer. This research aims to calculate the level of such residual stresses after the surface processing of Ti grade IV, Ti15Mo, and Ti6Al7Nb alloys with an Nd:YAG laser. Light and scanning electron microscopies...
-
Relationship between microstructure of laser alloyed C45 steel and its cavitation resistance.
PublicationW pracy przedstawiono badania wpływu laserowo kształtowanej mikrostruktury na stali C45 po stopowniu różnymi kompozycjami proszków metali na własności kawitacyjne warstwy wierzchniej. Badania prowadzono w początkowym stadium erozji kawitacyjnej. Stwierdzono, że lepszą odporność kawitacyjną osiąga się gdy mikrostruktura jest podatna do umacniania odkształceniowego np. w obecności pewnej ilości austenitu w strukturze.
-
Cavitation erosion of some laser-produced iron-base corrosion-resistance alloys
PublicationW pracy przedstawiono badania kawitacyjne stali C45, X20Cr13 oraz X5CrNi18-10 po laserowym stopowaniu ich warstwy wierzchniej proszkami Mn, Cr, Ni, Si, Ti, Co, Al, Mo, B. Badania kawitacyjne prowadzono na stanowisku z wirującą tarczą. Zniszczenia powierzchni w okresie inkubacji oceniano metodą optyczną. Przedstawiono związek pomiędzy uzyskaną mikrostrukturą obrabianej warstwy i jej odpornością kawitacyjną.
-
Relationship between microstructure of laser alloyed of C45 steel and its cavitation resistance.
PublicationPrzedstawiono badania odporności kawitacyjnej stali C45 po laserowym stopowaniu jej powierzchni proszkami Mn., Ni, Cr, Nb, Mo, Co. Stwierdzono, że warstwa wierzchnia posiada wyższą odporność kawitacyjną jeśli w jej mikrostrukturze występuje pewna ilość austenitu zwiększająca podatność do wzmacniania odkształceniowego.
-
Verification of the new viscoelastic method of thermal stress calculation in asphalt layers of pavements
PublicationThe new viscoelastic method of thermal stress calculations in asphalt layers has been developed and published recently by the author. This paper presents verification of this method. The verification is based on the comparison of the results of calculations with results of testing of thermal stresses in Thermal Stress Restrained Specimen Test. The calculations of thermal stresses according to the new method were based on rheological...
-
Spray pyrolysis of doped-ceria barrier layers for solid oxide fuel cells
PublicationGadolinium doped ceria (Ce0.8Gd0.2O2 − x-CGO) layer fabricated by spray pyrolysis is investigated as the diffusion barrier for solid oxide fuel cell. It is deposited between the La0.6Sr0.4FeO3 − δ cathode and the yttria stabilized zirconia electrolyte to mitigate harmful interdiffusion of elements. The parameters of the fabrication process are linked to the measured area specific resistances of the symmetrical cells and the efficiency...
-
APPLYING RANSAC ALGORITHM FOR FITTING SCANNING STRIPS FROM AIRBORNE LASER SCANNING
PublicationDuring the development of the data acquired by airborne laser scanning the important issue is the fitting and georeferencing of ALS point clouds by means of the tie surfaces and the reference planes. The process of scanning strips adjustment is based on mutual integration of point clouds (scanning strips) and their adaptation to the reference planes.In simultaneous adjustment all strips are combined into one geometrically coherent...
-
Application of the laser diode with central wavelength 975 nm for the therapy of neurofibroma and hemangiomas
PublicationThis paper presents newly developed dermatological laser (with central wavelength 975 nm) for application in therapies requiring deep penetration of tissue, e.g. cutaneous (dermal) neurofibroma (Recklinghausen disease) and hemangiomas. This laser can work either in pulse or continues wave mode. Laser radiation is transmitted toward the application region by optical fiber with a diameter of 0.6 mm. The compact design of the laser...
-
STUDIES ON THE USE OF TERRESTRIAL LASER SCANNING IN THE MAINTENANCE OF BUILDINGS BELONGING TO THE CULTURAL HERITAGE
PublicationWithin the frames of the use of terrestrial laser scanning we find numerous examples of registration of building facilities, including also historical and valuable in their culture. In the case presented in this paper, at the root of the problem there is a preservation of the historic blacksmith’s forge located in Gdansk Orunia. The facility dating from the early nineteenth century was intended to repair involving the complete...
-
THE METHOD OF ANALYSIS OF DAMAGE REINFORCED CONCRETE BEAMS USING TERRESTRIAL LASER SCANNING
PublicationThe authors present an analysis of the possibility to assess deformations and mode of failure of R-C beams using terrestrial laser scanning. As part of experiments carried out at the Regional Laboratory of Construction (at Gdansk University of Technology), reinforced concrete beams were subjected to destruction by bending and by shear. The process of press impact on the reinforced concrete beam was recorded using terrestrial laser...
-
THE METHOD OF MEASURING THE MEMBRANE COVER GEOMETRY USING LASER SCANNING AND SYNCHRONOUS PHOTOGRAMMETRY
PublicationThe authors present the experience and results of field studies carried out at the technical acceptance of Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland). An unusual design of covering made in the form of “Sheerfill I” technical fabric membrane required spanned in the form of sails, required the use of terrestrial laser scanning. Such approach allowed for the fast and accurate record of the surface of individual panels...
-
Studies on the use of terrestrial laser scanning in the maintenance of buildings belonging to the cultural heritage
PublicationWithin the frames of the use of terrestrial laser scanning we find numerous examples of registration of building facilities, including also historical and valuable in their culture. In the case presented in this paper, at the root of the problem there is a preservation of the historic blacksmith's forge located in Gdansk Orunia. The facility dating from the early nineteenth century was intended to repair involving the complete...
-
Influence of laser beam machining on the cavitation resistance of Fe-Cr-Co clad.
PublicationW pracy przedstawiono wpływ laserowego nagrzewania bezzmiany stanu skupienia i laserowego przetapiania napoin ze stopu Fe-Cr-Co na ich odporność kawitacyjną. Badania kawitacyjne prowadzono na stanowisku z wirującą tarczą. Plastyczne odkształcenia powierzchni określano za pomocą analizy obrazów erodowanych powierzchni. Uzyskane rezultaty wskazują, że laserowo obrabiane powierzchnie miały różną podatność do plastycznego odkształcania...
-
Colorimetric study of the post-processing effect due to pulsed laser cleaning of paper.
PublicationW artykule przedstawiono wyniki badań procesu oczyszczania papieru implulsami laserowymi o różnej długości fali. Oceny dokonywano na podstawie pomierzonych wartości parametrów kolorymetrycznych. Badania obejmowały próbki papieru o różnym wieku.
-
Relationship between cavitation resistance of laser produced alloys and their ability to work hardening
PublicationBadano odporność kawitacyjną laserowo wytworzonych stopów na stalach konstrukcyjnych i ich związek ze zdolnością do umacniania się pod wpływem działania obciążeń kawitacyjnych. Wykazano, że mikrotwardość powierzchni wykazuje monotoniczną zależność z odpornością kawitacyjną i zdolnością do umacniania.
-
Morphology and corrosion characteristics of laser surface remelted Al-Sialloy at cryogenic conditions
PublicationPrzedstawiono koncepcję obróbki laserowej stopu Al-Si w warunkach kriogenicznych. Określono jej wpływ na lokalny skład chemiczny oraz mikrostrukturę i właściwości korozyjne wymienionego stopu. Stwierdzono znaczącą poprawę właściwości korozyjnych w 0,01 M H2SO4.
-
Cavitation erosion of chromium-manganese and chromium-cobalt coatings processed by laser beam
PublicationPrzedstawiono wyniki badań erozji kawitacyjnej napoin wykonanych za pomocą elektrod chromowo-manganowych i chromowo-niklowych oraz obrobionych wiązką lasera CO2 o mocy 1000 W. Próbki poddawano obciążeniom kawitacyjnym na stanowisku z wirującą tarczą. Zaobserwowano wzrost odporności kawitacyjnej napoin, w których dokonano przetopienia ich powierzchni promieniowaniem lasera.
-
Corrosion characteristics of the AL-Si alloy after laser treatment at cryogenic conditions
PublicationOmówiono wpływ laserowego powierzchniowego przetapiania stopu Al-Si w warunkach kriogenicznych na jego mikrostrukturę i właściwości użytkowe. W wyniku badań korozyjnych stwierdzono zwiększenie odporności na korozję stopu Al-Siw 0,01 M roztworze H2SO4.
-
Cavitation erosion of some alloys manufactured on steel and iron surfaces by laser beam.
PublicationPrzedstawiono badania odporności kawitacyjnej stali węglowej 45 odpornej na korozję 2H13 i technicznego żelaza po ich obróbce laserowej. Warstwę wierzchnią wybranych stali wzbogacono w różne pierwiastki stopowe i badano odporność kawitacyjną na stanowisku z wirującą tarczą. Stwierdzono niską odporność kawitacyjną dla warstw o obniżonej zdolności do utwardzania pod wpływem obciążeń kawitacyjnych oraz silną zależność odporności...
-
Tunable semiconductor laser application for interferometric optical fibersensors.Optical and Electronic Sensors V.
PublicationW pracy przedstawiono metody stabilizacji punktu pracy światłowodowych sensorów interferometrycznych. W metodach tych wykorzystuje się układy regulacji sterujące długością fali przestrajalnego lasera półprzewodnikowego. Przedstawiono tryby pracy układów regulacji oraz problemy związane z ich projektowaniem i realizacją. Przeanalizowano ograniczenia sensorów wykorzystujących powyższe układy. Dokonano weryfikacji eksperymentalnej...
-
BACTERIAL INACTIVATION VIA LASER-DRIVEN GOLD NANOPARTICLE HEATING: SIMULATION AND ANALYSIS
PublicationThis study utilizes CFD technique to simulate the inactivation of E. coli bacteria within a microfluidic chamber, employing gold nanoparticles irradiated by a laser beam. Employing a single-phase model, the presence of bacteria is considered by treating thermal properties in the governing equations as effective, combining those of water and bacteria using established correlations from scientific literature. The conversion of light...
-
Effects of preheating on laser beam–welded NSSC 2120 lean duplex steel
PublicationDuplex stainless steels show sustainable alternative for the conventional austenitic grades, with higher strength, higher resistance against stress corrosion cracking, and lower purchase cost. Thus, duplex stainless steel gains more attention in construction, oil and gas, and chemical industries. Among duplex stainless steels, low nickel and low molybdenum alloyed lean duplex stainless steel are a cost-efective substitution of...
-
Heat Transfer of the Multicolor-Laser-Sources-Irradiated Nanoparticles in Reference to Thermal Processes
PublicationUnlike the standard materials, metallic nanoparticles offer enhancing the heat convertion rate which implies the maximum and average temperature boost significantly in the considered system. The work’s purpose is to examine heat transfer in the metallic nanoparticles which have been deposited on a glassy substrate, enabling the nanostructures thermoablation. Furthermore, the functionalized substrate is irradiated with multicolor-laser-sources,...
-
Investigations of Energy Conversion and Surface Effect for Laser-Illuminated Gold Nanorod Platforms
PublicationAchieving a quick temperature increase is a burning issue for biophysical applications, like germ inactivation and tumor ablation, and for energy performances, like solar collectors and steam generators. Based on the plasmon resonance phenomenon, noble metallic nanoparticles have emerged as promising weapons due to their very high biocompatibility, optical properties, and high surface-to-volume ratio, increasing energy conversion...
-
Photovoltaic properties of a sandwich cell consisting of bromophosphorus phthalocyanine and titanium dioxide layers
PublicationPraca omawia wyniki badań doświadczalnych właściwości fotowoltaicznych układu: ITO/bromofosforowa ftalocyjanina/dwutlenek tytanu/tetracen/Au.
-
Effect of plasma nitrided layers on low-alloy steel on its hydrogen degradation
PublicationPrzedstawiono badania wpływu warstw azotowanych jarzeniowo na stali 34CrAlNi7-10 na jej podatność na niszczenie wodorowe. Wytworzono warstwy azotowane w atmosferach technologicznych o różnym udziale wodoru. Próbki materiału rodzimego i z warstwami azotowanymi poddano próbie rozciągania z małą prędkością odkształcania w środowisku 0,01 N kwasu siarkowego przy polaryzcaji katodowej. Względny spadek plastyczności i charakter przełomu...
-
Effect of pulse laser treatment at different process variables on mechanical behavior of carbon nanotubes electrophoretically deposited on titanium alloy
PublicationPurpose: Titanium and its alloys are widely used as biomaterials for long-term implants, but they are usually surface-modified due to their weak bioactivity and wear resistance. Laser processing was used to modify the surface layer, and elemental carbon was a component of the deposited coatings. This research aims to use a combination of both methods based on preliminary electrophoretic deposition of multi-wall carbon nanotubes...
-
Properties of Barium Cerate-Zirconate Thin Films
PublicationIn this work, we review several experimental results showing the electrical properties of barium cerate-zirconate thin films and discuss them in view of the possible influence of various factors on their properties. Most of the presented Ba(Ce, Zr, Y)O3 thin films were formed by the pulsed laser deposition (PLD) technique, however thin films prepared using other methods, like RF magnetron sputtering, electron-beam deposition, powder...
-
Reversed-phase and normal-phase thin-layer chromatography and their application to the lipophilicity prediction of synthetic pyrethroids based on quantitative structure–retention relationships
Publication -
Experimental research on water lubricated three layer sliding bearing with lubrication grooves in the upper part of the bush and its comparison with a rubber bearing
Publicationcomposite. Eachofitslayershasanimportantfunction.Speciallypreparedslidingsurfaceensures minimum resistance.Followingrunning-initssmoothnessbecomesveryhighandthebearingmay continue workingunder fluid lubricationregime.NBRlayerensuresbearingelasticity,goodvibration damping propertiesandinsusceptibilitytoshaftaxismisalignment.Theexternalbrasslayermakes fitting thebearingeasier. Experiment resultsoftheconductedresearchwerecomparedwiththoseforarubberbearingof similar...
-
Method of identification of the slide tribological system top layer condition by assessment of the t-02 four-ball tester friction node operation
Publicationa method is proposed of the assessment of t-02 four-ball tester friction node operation during extreme unit loads on the tribological system for identification of the top layer condition in that system lubricated with the tested lubricating oil. by identification of the friction node with a thermodynamic system, that operation is treated as an energy generating process of the created servo-layer structure. the friction node operation...
-
Effect of Na doping on photoluminescence and laser stimulated nonlinear optical features of ZnO nanostructures
Publication -
Technology of laser deposition of narrow bead overlays using solid and flux-cored wires
Publication -
Variable Temperature Spectroscopic Ellipsometry as a Tool for Insight into the Optical Order in the P3HT:PC70BM and PC70BM Layers
PublicationTwo combined ellipsometric techniques—variable angle spectroscopic ellipsometry (VASE) and variable temperature spectroscopic ellipsometry (VTSE)—were used as tools to study the surface order and dielectric properties of thin films of a poly(3-hexylthiophene-2,5-diyl) (P3HT) mixture with a fullerene derivative (6,6-phenyl-C71-butyric acid methyl ester) (PC70BM). Under the influence of annealing, a layer of the ordered PC70BM...