Search
Filters
total: 3337
filtered: 2791
displaying 1000 best results Help
Search results for: forced vibrations
-
EXPERIMENTAL STUDY OF A TEMPORARY STEEL GRANDSTAND UNDER CROWD LOAD
PublicationTemporary structures, such as grandstands, are commonly used during different types of mass events, especially sport and music concerts. In this paper, the results of the experimental study on temporary steel grandstand are presented. The aim of the investigation was to determine modal characteristics of such structures. Modes of free vibrations and corresponding natural frequencies have been obtained for empty and occupied grandstand....
-
Stability of Discrete Fractional Order State-space Systems
Publication -
Modelling of wave propagation in composite plates using the time domain spectral element method
PublicationW pracy przedstawiono wyniki obliczeń propagacji fali sprężystej w płycie kompozytowej modelowanej z wykorzystaniem czasowego sformułowania metody elementów spektralnych
-
Assessment of rod behavior theories used in spectral finite element modeling
PublicationW pracy przedstawiono teorie prętów i przedstawiono ich przydatnośc w analizie propagacji fal sprężystych z wykorzystaniem metody spektralnych elementów skończonych.
-
Experimental and numerical study on damage detection in an L-joint using guided wave propagation
PublicationW pracy zaprezentowano metodę wykrywania i lokalizacji uszkodzeń w konstrukcji ramowej za pomocą podłużnych i poprzecznych fal sprężystych. Przeprowadzono badania numerczyne i eksperymentalne na modelu bez uszkodzenia oraz na modelu z wsprowadzonym nacięciem. Do modelowania zastosowano metodę elementów spektralnych. W pracy przedstawiono sformułowanie nowego element spektralnego dla ram płaskich bazującego na teorii pręta Mindlina...
-
Experimental and numerical study on damage detection in an L-joint using guided wave propagation
Publication -
Fast bubble dynamics and sizing
PublicationSingle bubble sizing is usually performed by measuring the resonant bubble response using the Dual Frequency Ultrasound Method. However, in practice, the use of millisecond-duration chirp-like waves yields nonlinear distortions of the bubble oscillations. In comparison with the resonant curve obtained under harmonic excitation, it was observed that the bubble dynamic response shifted by up to 20 percent of the resonant frequency...
-
Performance Characteristics of a Micro-Turbine
PublicationIn the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:heat output:...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublicationThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
Longitudinal wave propagation. Part II, Analysis of crack influence
PublicationW pracy analizowano wpływ pęknięć zmęczeniowych na propagacje fali wzdłużnej w prętach. Opracowano nowe typy element ów spektralnych oparte na teorii elementarnej, Love'a, Mindlina i trójpostaciowej.
-
Longitudinal wave propagation. Part I - Comparison of rod theories
PublicationW pracy przedstawiono modele spektralnych elementów skończonych do analizy propagacji fali wzdłuznej w pretach. Opracowano modele wykorzystujace teorię elementarną, teorie Love'a, teorie Mindlina oraz teorię trójpostaciową.
-
Considerations about the applicability of the Reynolds equation for analyzing high-speed near field levitation phenomena
Publicationequation for analyzing near field levitation (NFL) phenomena. Two separate approaches were developed, experimentally verified, and applied to meet the research objective. One was based on the Reynolds equation and the other was based on general conservation equations for fluid flow solved using computational fluid dynamic (CFD). Comparing the calculation results revealed that, for certain operating conditions, differences in the...
-
The dynamic analysisi of cracked Thimoshenko beam by the spectral element method.
PublicationW pracy przedstawiono model belli Timoshenko z pęknięciem poprzecznym oparty o metodę elementów spektralnych. Przedstawiono wyniki propagacji fali sprężystej i jej interakcję z pęknięciem.
-
The dynamic analysis of a cracked Timoshenko beam by the spectral element method
Publication -
Longitudinal wave propagation. Part I—Comparison of rod theories
Publication -
Wave propagation in a sensor/actuator diffusion bond model
Publication -
Longitudinal wave propagation. Part II—Analysis of crack influence
Publication -
Wave propagation modelling in 1D structures using spectral finite elements
PublicationW artykule omówiono modele propagacji fal wzdłużnych i poprzecznych w prętach oparte na dwóch sformułowaniach (w dziedzinie częstości i w dziedzinie czasu) metody elemntów spektralnych. Porównano otrzymane wyniki z wynikami eksperymentu.
-
High frequency dynamics of an isotropic Timoshenko periodic beam by the use of the Time-domain Spectral Finite Element Method
PublicationIn this work results of numerical simulations and experimental measurements related to the high frequency dynamics of an aluminium Timoshenko periodic beam are presented. It was assumed by the authors that the source of beam structural periodicity comes from periodical alterations to its geometry due to the presence of appropriately arranged drill-holes. As a consequence of these alterations dynamic characteristics of the beam...
-
Assessment of flexural beam behaviour theories used for dynamics and wave propagation problems
PublicationW pracy przedstawiono i porównano teorie belek zginanych począwszych od teorii elementarnych, aż do teorii wyższych rzędów. Przedstawiono krzywe dyspersi dla poszczególnych teorii i na ich podstawione oszacowano zakres stosowalności danej teorii.
-
Pressure Pulsations in Turbine Blade Seal
PublicationThe paper presents the results of experimental investigations into pressure forces generated in a turbine labyrinth seal. The experiments were performed on a single-stage air model turbine of the impulse type. The performed experimental research proved that in a shroud clearance the pressure pulsates and the effects of the nozzle trailing edge thickness as well as the influence of the rotor blades are observed. The exemplary results...
-
Nanostructure and dielectric behavior of vanadate glasses containing BaTiO3
PublicationThe ac and dc electrical conductivity of barium titanate doped bismuth-vanadate as-quenched and heat-treated materials was measured in the frequency range from 1 mHz to 1 MHz and in the temperature range from 153 K to 423 K with the impedance spectroscopy method. The microstructure was investigated by means of XRD, scanning electron microscopy (SEM), atomic force microscopy (AFM) and confocal microscopy. The obtained results showed...
-
Analysis of the effect of the seismic gap on the response of buildings experiencing pounding during earthquakes
PublicationThe aim of this paper is to investigate the effect of the seismic gap on the dynamic response of buildings experiencing earthquake-induced pounding. Three buildings have been analysed, which are 5-storey, 7-storey and 9-storey structures. Three possible pounding scenarios have been considered, which are pounding between 5-storey and 7-storey buildings, pounding between 5-storey and 9-storey buildings and pounding between 7-storey...
-
Thermal Instability of Gold Thin Films
PublicationThe disintegration of a continuous metallic thin film leads to the formation of isolated islands, which can be used for the preparation of plasmonic structures. The transformation mechanism is driven by a thermally accelerated diffusion that leads to the minimalization of surface free energy in the system. In this paper, we report the results of our study on the disintegration of gold thin film and the formation of nanoislands...
-
Effect of surface on the flexomagnetic response of ferroic composite nanostructures; nonlinear bending analysis
PublicationOur analysis incorporates the geometrically nonlinear bending of the Euler-Bernoulli ferromagnetic nanobeam accounting for a size-dependent model through assuming surface effects. In the framework of the flexomagnetic phenomenon, the large deflections are investigated referring to von-Kármán nonlinearity. Employing the nonlocal effects of stress coupled to the gradient of strain generates a scale-dependent Hookean stress-strain...
-
Hybrid quantum-classical approach for atomistic simulation of metallic systems
PublicationThe learn-on-the-fly (LOTF) method [G. Csanyi et al., Phys. Rev. Lett. 93, 175503 (2004)] serves to seamlessly embed quantum-mechanical computations within a molecular-dynamics framework by continual local retuning of the potential's parameters so that it reproduces the quantum-mechanical forces. In its current formulation, it is suitable for systems where the interaction is short-ranged, such as covalently bonded semiconductors....
-
New Trends in Sample Preparation Techniques for the Analysis of the Residues of Pharmaceuticals in Environmental Samples
PublicationPharmaceutical residues in the environment is a field of special interest due to the adverse effects to either human health or aquatic and soil environment. Pharmaceuticals have been already detected in underground, surface and wastewaters, soils, manure and sediments. The growing awareness of environmental pollution arising from human activity forces the need for their comprehensive determination. Environmental samples are complex...
-
Novel digitally controlled drive for the vibratory conveyors
PublicationThe presented vibratory conveyors is used in the industry for continuous transportation of loose substances over short distances (2-10 m). The conveyor is applied for transportation in aseptic conditions. To obtain high efficiency for granulatedmass with different size of grain and different physical properties it is necessary to set the appropriate vibration amplitudeindependently of vibration frequency. This is not possible with...
-
Study on polymer elements for mitigation of earthquake-induced pounding between buildings in complex arrangements
PublicationPounding between neighbouring buildings during earthquakes has been identified as one of the reasons for substantial damage or even total collapse of colliding structures, so it has been the subject of numerous studies in the recent years. A major reason leading to interactions between adjacent, insufficiently separated structures results from the differences in their dynamic properties. The problem is much more complicated for...
-
Determination of stepped plate thickness distribution using guided waves and compressed sensing approach
PublicationGuided waves recently have attracted significant interest as a very promising research area. The signals registered by a specially designed sensor network are processed to assess the state of the tested structure. Despite the constant development of novel damage detection algorithms employing guided waves, the phenomenon of wave propagation still needs detailed recognizing and understanding for the further progress of non-destructive...
-
Point cloud based surface analysis of prestressed concrete element in exceeded state of serviceability
PublicationBy definition, serviceability state is characterized by the fact that despite meeting the requirements associated with carrying capacity, the object is not suitable for use. Serviceability limit state refers to factors, such as durability, overall stability, fire resistance, cracking, excessive vibration. Perfect examples of exceeded serviceability state are the improper vibration of a skyscraper, which inhabitants may suffer from...
-
STABILITY OF THE INNER SLOPE OF THE POLISH DREDGDIKES RESEARCH DIKE AT STATIONARY FLOW
PublicationFor long duration of the flood the water table can appear on the slope with a problem of out-wash in the case of sand type dike. If the dike corps is covered with less permeable layer some additional push-off forces and shearing can rise in the cover. In both cases the micro stability of the inner slope should be considered at normative high water for homogeneous sand type dike or sand type dike with less permeable covers. The...
-
Drewno w adoptowanym zabytku - studium przypadku. Budynek nr 2 w dawnych koszarach garnizonu we Wrzeszczu
PublicationThe current structure along with adapted listed buildings and surroundings will create "Garrison of Culture".This part of Gdańsk and Wrzeszcz has been reconnected after eight decades of isolation from the city by joining the square area formed by Grunwaldzka, Słowackiego, Chrzanowskiego, Szymanowskiego streets and the city center. It is a project whitch fits into an aspect of revitalisation related to the socio-economic and environmental...
-
Renewable and Sustainable Energy: Current State and Prospects
PublicationThe last two decades of the twentieth century represented a period of above-average, systematic growth of formal and informal interdependencies between economies of different countries and between world markets. The intensity, magnitude, and diversity of these interdependencies have never been recorded before in economic history, and the market transformations taking place have been referred to in the literature as the process...
-
Water-lubricated stern tube bearing - experimental and theoretical investigations of thermal effects
PublicationThe paper presents research results of thermal phenomena accompanying operation of a water-lubricated stern tube bearing with axial grooves. Experimental tests revealed, that intensity of forced axial flow has strong influence on bush temperature. Numerical simulations focused on investigation of the thermal phenomena under operation of water-lubricated journal bearing showed, that restricted axial flow promotes backflow of the...
-
Optical Emission Spectroscopy of Microwave (915 MHz) Plasma in Atmospheric Pressure Nitrogen with Addition of Ethanol Vapour
PublicationIn this paper results of optical emission spectroscopic study of microwave 915 MHz plasma in atmospheric pressure nitrogen with an addition of ethanol vapour are presented. The plasma was generated in waveguide- -supplied cylinder-type nozzleless microwave plasma source. The aim of research was to determine the rotational Trot and vibrational Tvib temperatures of CN and C2. A method called bubbling was employed to introduce alcohol (ethanol)...
-
Investigations of size effect in concrete at aggregate level - experiments and calculations results using discrete element method
PublicationSize effect is a fundamental phenomenon in concrete. It is characterised by decreasing strength and increasing brittleness of concrete with increasing size. The thesis includes experimental and theoretical elements. The main goal of the thesis were investigations of a size effect at the aggregate level by taking fracture into account with the discrete element method (DEM) for various failure modes. Comprehensive experiments on...
-
Quantitative assessment of the influence of tensile softening of concrete in beams under bending by numerical simulations with XFEM and cohesive cracks
PublicationResults of the numerical simulations of the size effect phenomenon for concrete in comparison with experimental data are presented. In-plane geometrically similar notched and unnotched beams under three-point bending are analyzed. EXtended Finite Element Method (XFEM) with a cohesive softening law is used. Comprehensive parametric study with the respect to the tensile strength and the initial fracture energy is performed. Sensitivity...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublicationTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
Wave Method for Structural Health Monitoring: Testing Using Full-Scale Shake Table Experiment Data
PublicationAn algorithm of the wave method for structural health monitoring (SHM) is tested and calibrated using shake table experiment data of a full-scale, seven-story, reinforced-concrete building slice. The method is based on monitoring changes in the velocity of waves propagating vertically through the structure, identified by least-squares (LSQ) fit of beam models. The experiment was conducted by a team from the University of California,...
-
RAPORT - EKSPERTYZA Z POMIARÓW DRGAŃ LINII WAŁÓW NA JEDNOSTCE ORP „DĄBIE”
PublicationEkspertyza diagnostyczna dotycząca stanu technicznego dwóch linii transmisji mocy (linii wałów) opracowana na podstawie przeprowadzonych pomiarów drgań w 26 punktach pomiarowych, przy jednoczesnej pracy silników napędowych L i PB (wspólnej pracy linii wałów obu burt), w II zakresach ustalonego obciążenia „pół-naprzód” i „cała-naprzód”. Pomiary prędkości i przyspieszeń drgań generowanych przez węzły konstrukcyjne okrętowego układu...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublicationThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
Physics-Based Coarse-Grained Modeling in Bio- and Nanochemistry
PublicationCoarse-grained approaches, in which groups of atoms are represented by single interaction sites, are very important in biological and materials sciences because they enable us to cover the size- and time-scales by several orders of magnitude larger than those available all-atom simulations, while largely keeping the details of the systems studied. The coarse-grained approaches differ by the scheme of reduction and by the origin...
-
Threshold photoelectron studies of isoxazole over the energy range 9.9-30 eV
PublicationThe threshold photoelectron spectrum of the isoxazole molecule, C3H3NO has been measured over the photon energy range 9.9-30 eV with the use of synchrotron radiation. In the 9.9-10.8 eV range, corresponding to photoionization from the highest occupied molecular orbital 3a"(π3), seven well resolved vibrational series have been observed and their modes are tentatively assigned. A strong adiabatic ionization, with an energy of 11.132...
-
Reference FEM model for SHM system of cable-stayed bridge in Rzeszów
PublicationThe paper presents the references model for structural health monitoring system (SHM) of cable-stayed bridge recently constructed in Rzeszów over Wisłok River. The SHM system is design to provide on-line information on the structure state and facilitate its maintenance procedures. The main feature of the SHM system is permanent observation of the dynamic behavior of the bridge with focus on cable vibrations. The paper discusses...
-
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublicationThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
Enhancing rheological muscle models with stochastic processes
PublicationPurpose: Biological musculoskeletal systems operate under variable conditions. Muscle stiffness, activation signals, and loads change during each movement. The presence of noise and different harmonic components in force production significantly influences the behaviour of the muscular system. Therefore, it is essential to consider these factors in numerical simulations. Methods: This study aims to develop a rheological mathematical...
-
Features of Nonlinear Sound Propagation in Vibrationally Excited Gases
PublicationWeakly nonlinear sound propagation in a gas where molecular vibrational relaxation takes place is studied. New equations which govern the sound in media where the irreversible relaxation may take place are derived and discussed. Their form depends on the regime of excitation of oscillatory degrees of freedom, equilibrium (reversible) or non-equilibrium (irreversible), and on the comparative frequency of the sound in relation to...
-
Study on Polymer Elements for Mitigation of Earthquake-Induced Pounding Between Buildings in Complex Arrangements
PublicationPounding between neighboring structures during seismic events has been revealed as one of the most commonly observed reasons for severe damage or even total collapse of the adjacent buildings. Therefore, pounding effects have recently become an issue of great interest of many numerical and experimental investigations in many earthquake-prone regions of the world. It has also been observed that the differences in dynamic characteristics...
-
Application a laboratory stand for multi-symptoms tests for high cyclic fatigue of constructional material
PublicationThis paper describes a need of diagnostics present ship plants according to current technical state. In order to reach competent physical quantity describing fatigue of materials by congregated energy. This paper describes using some diagnostics methods (acoustic emission AE, vibration, thermovision, deformation) in order to definition fatigue state of construction material. The author tries to find correlation between measured...