Filters
total: 806
filtered: 556
-
Catalog
Chosen catalog filters
Search results for: KOLUMNA ŻWIROWA
-
Column base fixity in steel moment frames: Observations from instrumented buildings
PublicationThe rotational fixity of column base connections in Steel Moment Resisting Frames (SMRFs) strongly influences their seismic response. However, approaches for estimating base fixity have been validated only against laboratory test data. These approaches are examined based on strong motion recordings from four instrumented SMRF buildings in California to informbest practices for seismic response simulation. These buildings represent...
-
Effects of Column Base Flexibility on Seismic Response of Steel Moment-Frame Buildings
PublicationSteel Moment Resisting Frames (SMRFs) are very popular lateral load resisting systems in many seismically active regions. However, their seismic response is strongly dependent on the rotational fixity of column base connections. Despite many studies (both experimental and numerical) in this particular area, available approaches for estimating column base flexibility have been validated only against laboratory test data. In the...
-
Analysis of the Hydrodynamic Properties of the 3-Column Spar Platform for Offshore Wind Turbines
PublicationThe article presents a design of a floating platform for offshore wind turbines. The concept is a modification of the Spar design and consists of three variable section columns connected to each other by a ballast tank in the lower part of the platform. This solution makes it possible to influence the position of the centre of buoyancy and the centre of mass of the structure. Compared to the classic Spar platform structure, the...
-
Ekspertyza techniczna dotycząca wpływu drgań na kolumny betonowe wykonywane w ramach budowy drogi ekspresowej S19 Lubartów-Kraśnik
PublicationCelem ekspertyzy było określenie wpływu drgań generowanych w trakcie wytwarzania nowej kolumny betonowej na już istniejące, które zostały wykonane wcześniej.
-
Comparison of RP-HPLC columns used for determination of nucleoside metabolic patterns in urine of cancer patients
Publication -
Application of PCR-HRM method for microsatellite polymorphism genotyping in the LDHA gene of pigeons (Columba livia)
Publication -
Uproszczona metoda wyznaczania współczynnika dyspersji wzdłużnej dla cieczy we współprądowej kolumnie barbotażowej
PublicationZastosowano uproszczoną metodę Aoyama do wyznaczania współczynników dyspersji wzdłużnej dla cieczy w kolumnie barbotażowej z ciągłym współprądowym przepływem gazu i cieczy. Wartości współczynników dyspersji wyznaczono eksperymentalnie stosując metodę znacznikową.
-
Zaangażowanie i rozwój pracowników każdego szczebla. Kolejna z fundamentalnych zasad doskonalenia jakości
PublicationW niniejszym oracowaniu poddano analizie zaangażowwanie i rozwój pracowników jako podstawę funcjonowania podmiotów dążących do zwiększenia swojej dojrzałości projakościowej. Autor wskazał odniesienia do tego obszaru w teorii Kompleksowego Zarządzania Jakością wraz z podstawowymi uwarunkowaniami zaangażowania proacowników.
-
Comparison of buckling resistance of columns modelled by beam and shell elements using non-linear analysis
PublicationThe aim of the paper is to investigate the stability process in the axially compressed columns modelled by beam and shell elements using static and dynamic finite element analysis by taking both the geometric and material non-linearity into account. The perfect columns and columns with geometric imperfections were analysed. The differences between the results of static and dynamic analyses in shell and beam models were discussed.
-
Study on 19th-century cast iron columns from the former financial office building in Kwidzyn
PublicationThe article presents the results for cast iron columns used as floor supports in the former financial office building in Kwidzyn (Poland).The stocktaking drawings provided the general and detailed data about the 19th century designer’s decisions. During the research, architectural and structural analysis was carried out. The graphics were used as a starting material for preparing 3D calculation models. The FEM-based numerical simulations...
-
Pore Water Pressure Development in Soft Soil due to Installation and Loading of Controlled Modulus Columns
PublicationExcess pore water pressure (EPWP) development and decay due to the installation and static loading tests of controlled modulus columns (CMC) in soft soil was measured with piezometers equipped with low air entry (LAE) filters and a piezocone (CPTU) equipped with a high air entry (HAE) filter. The HAE filter allows for detailed detection of EPWP in short time intervals during construction of CMC. The influence zone due to the installation...
-
Evaluation of the usefulness and optimization of the separation conditions in Empty Column Gas Chromatography (EC-GC)
PublicationDotychczasowe badania wykazały, że możliwe jest rozdzielanie wysokowrzących mieszanin techniką chromatografii gazowej z zastosowaniem pustej rurki kapilarnej z topionej krzemionki, zamiast kolumn zawierających fazę stacjonarną. Operacja rozdzielania chromatograficznego ma miejsce jedynie na zasadzie różnicy temperatur wrzenia rozdzielanych substancji. Wysoki stopień podobieństwa warunków rozdzielania, osiąganych w ten sposób, z...
-
The buckling analysis of a cold-formed steel C-sectional column resting on an elastic foundation
PublicationThe paper is focused on stability analysis of different models of steel cold-formed C-section column. The analysed element may be applied as a primary load-bearing member in steel trusses or silo columns. The column can be used as a support for a wall of roof plates made of corrugated sheets. The wall sheeting that restrains the column against buckling may be considered as an elastic foundation. Due to the design solutions the...
-
Influence of a Lighting Column in the Working Width of a W-Beam Barrier on TB51 Crash Test
PublicationRoad equipment, such as, e.g., road safety barriers and lighting columns, are subject to certification according to the EN1317 standard to be allowed for use on European roads. In engineering practice, due to the terrain conditions, there are cases where other road equipment is installed within the working width of road safety barriers. Such situations are not considered during the certification process. Hence, the aim of this...
-
The effect of nonlinear restraint on torsional buckling and post-buckling behaviour of a thin-walled column
PublicationW pracy rozważa się wyboczenie skrętne i zachowanie pokrytyczne osiowo ściskanego swobodnie podpartego pręta cienkosciennego o przekroju otwartym ze sprężytą nieliniową podporą w środku rozpietości. Rozwiązanie problemu wyznaczono za pomocą metody małego parametru. W przykładzie numerycznym wyznaczono siłę krytyczną i ścieżkę początkowego zachowania pokrytycznego dwuteowego pręta z podporą sprężystą o charakterystyce składającej...
-
Powierzchnia międzyfazowa gaz - ciecz w roztworach białka serwatkowego napowietrzanych we współprądowej kolumnie barbotażowej
PublicationBadano rozkłady wielkości pęcherzy oraz stopień zatrzymania gazu podczas ciągłej separacji pianowej białka serwatkowego we współprądowej kolumnie barbotażowej. Średnice pęcherzy wyznaczano metodą fotograficzną. posługując się przecietną powierzchniowo-objętościową średnicą pęcherzy oraz wartością stopnia zatrzymania gazu wyznaczano wielkość generowanej powierzchni międzyfazowej.
-
Load-carrying capacity of axially loaded concrete-filled steel tubular columns made of thin tubes
PublicationAn experimental investigation was conducted on 30 CFST columns. An influence of the following factors on load-carrying capacity of the investigated columns was analyzed: the column slenderness (l1 = 42, l2 = 27 and l3 = 15), the tube thickness (the reinforcement ratio was equal to 4% or 6%), the way of applying the load to CFST columns (through the concrete core or through the entire cross-section), the bond strength between a...
-
Failure of cylindrical steel silos composed of corrugated sheets and columns and repair methods using a sensitivity analysis
PublicationW artykule omówiono przypadek awarii metalowego silosu z blachy walcowej i pionowych słupów. Wykonano analizę wyboczeniową MES z uwzględnieniem imperfekcji geometrycznych. Omówiono metody naprawcze i ich optymalizację w oparciu o analizę wrażliwości.
-
Determination of pesticides in water using new solid phase extraction technique - speedisk and speedisk column.
PublicationW publikacji opisano zastosowanie nowych narzędzi do ekstrakcji do fazy stałej: szybkie dyski i szybkie kolumienki (speedisk i speedisk column). Zaprezentowano ich zastosowanie do ekstrakcji pestycydów z próbek wody, przy zastosowaniu różnych rozpuszczalników.
-
Normal stress distribution in built‑up cold‑formed column in relation to interconnecting bolt spacing
PublicationIn order to increase a stiffness of cold-formed steel (CFS) elements it is practised to built-up the cross-section. In the analysed case, a main element is strengthened by adding extra chord in contact partially along the column. This additional chord acts as a longitudinal stiffener connected with the main section by series of bolts. Authors check whether rules applied over the years, for hot-rolled elements, can be indiscriminately...
-
Uncertainty of antioxidant profiling in complex mixtures using liquid chromatography involving post-column derivatisation
PublicationThe main goal of this paper is to discuss the problems associated with antioxidant profiling in complex samples using a high-throughput HPLC system coupled with post-column derivatisation reactor. Based on the experimental data reported in the literature, we demonstrated that improper optimisation of temperature and/or pH assay conditions performed using an on-line derivatisation reactor may substantially change the antioxidant...
-
A research on the optimal conditions for separation and identyfication of the components from the Droseraceae extracts by column liquid chromatography
PublicationThe isolation of the components with anticipated biological properties i.e. antimicrobial, fungicidal, antioxidant and perhaps anticancer activity is for many years a one of the biggest issues of modern separation science. Their obtaining based on the isolation of the components with the biological activity from in vitro cultured plants by extraction techniques is often more difficult than their production by the chemical synthesis.The...
-
Experimental and analytical analysis of punching shear in flat slabs supported on column topped with concrete head
PublicationAn experimental laboraatory test of the two series of slab-column elements topped with drop panels of varying sizes is described in this paper. The scope of the paper is to investigate the influence of the drop panel size and stiffness on the behaviour of the connection between the flat slab and the column topped by the concrete head. The impact of the head size and stiffness is analysed analytically and experimentally. The experimental...
-
Precipitation of Spherical Vaterite Particles via Carbonation Route in the Bubble Column and the Gas-Lift Reactor
PublicationSpherical vaterite particles were produced by carbonation of calcium chloride solution with addition of ammonia to facilitate CO2 absorption. Synthesis of calcium carbonate was carried out in a bubble column or gas-lift reactor. The course of the reaction was monitored by pH measurements. Precipitated solids were analyzed by Fourier-transformed infrared spectroscopy, x-ray powder diffraction and scanning electron microscopy, and...
-
Application of the ‘CPT 2012’model of AFNOR standard for column design in Poland–Jazowa case study
Publicationhis paper presents the ‘CPT 2012’ model incorporated into the AFNOR NF P94-262:2012-07, French standard for pile design fully compatible with Eurocode 7, to the wider Polish audience. The bearing capacity of three reference columns for Vistula Marshlands have been calculated according to ‘CPT 2012’ model and AFNOR recommendations. Then, the design resistances have been compared with ultimate column bearing capacity measured during...
-
Bifurcation of equilibrium forms of a gas column rotating with constant speed around its axis of symmetry
PublicationWe will be concerned with the problem of deformation of the lateral surface of a column that rotates with constant speed around its axis of symmetry. The column is filled by a gas and our goal is to investigate the deformation of the lateral surface depending on the pressure of the gas.
-
Buckling resistance of a metal column in a corrugated sheet silo - experiments and non-linear stability calculations
PublicationThe results of experimental and numerical tests of a single corrugated sheet silo column’s buckling resistance are presented in this study. The experiments were performed in a real silo with and without bulk solid (wheat). A very positive impact of the bulk solid on the column buckling resistance occurred. The experimental results were first compared to the buckling resistance calculated by Eurocode 3 formulae. The comparison revealed that...
-
Study on deformed steel columns subjected to impact load due to soft-storey failure in buildings during earthquakes
PublicationThe so called soft-storey failure is one of the most typical types of damage induced in buildings as the result of earthquake excitation. It has been observed during ground motions that the failure of an upper soft storey of a structure results in large vertical impact load acting on the lower floors. If the resistance of the structural members of the lower storeys is not sufficient it may further lead to progressive collapse of...
-
TS-based RSM-aided design of cold-formed steel stiffened C-sectional columns susceptible to buckling
PublicationThe paper focuses on joint-performance analysis of a built-up cold-formed thin-walled C-sectional column with a fillister (stiffener) of the same type, interconnected with a series of bolts located along the length of the compressed members in specific spacing. The quantity of bolts and the non-connected starting distance of the fillister are considered random variables of the problem. Optimal distribution of joints on the stiffener...
-
Application of linear buckling sensitivity analysis to economic design of cylindrical steel silos composed of corrugated sheets and columns
PublicationThe paper deals with global stability of steel cylindrical silos composed of corrugated walls and vertical columns with loads imposed by a bulk solid following Eurocode 1. The optimum silo design with respect to the steel weight was based on a sensitivity analysis method. The changes of silo column profiles at each design step were performed by means of influence lines for the buckling load factor due to the unit column bending...
-
Ammonium removal from aqueous solution by natural zeolite, Transcarpathian mordenite, kinetics, equilibrium and column tests.
PublicationOpisano wyniki badań procesu usuwania jonów amonowych z wodnych roztworów modelowych z wykorzystaniem mordenitu-naturalnego zeolitu (w postaci surowej i po odpowiedniej wstępnej obróbce) zarówno w warunkach statycznych jak i dynamicznych. Oszacowano pojemność jonowymienną w stosunku do jonów amonowych (1,64 meq/g) w przypadku, gdy stężenie początkowe analitu było na poziomie 1000 mg/l. Sprawdzono również wpływ na przebieg procesu...
-
Research on the separation properties of empty-column gas chromatography (EC-GC) and conditions for simulated distillation (SIMDIS)
PublicationThe paper presents the results of investigations on new procedures of determination of selected cleaning additives in diesel fuel. Two procedures: one-step analysis using gas chromatography with flame ionization detection (GC-FID) or mass spectrometry (GC-MS) and a two-step procedure in which normal-phase high-performance liquid chromatography (NP-HPLC) was used for preliminary separation of the additives, were compared. The additive...
-
HPLC-coupled post-column derivatization aims at characterization and monitoring of plant phytocomplexes, not at assessing their biological properties
PublicationTwo recent decades of research identified a number of environmental factors as well as mechanisms leading to pathogenic processes in the human organism. A common factor in pathogenesis of many diseases is oxidative stress, a condition in which the production of damaging reactive oxygen species (ROS), present in the body as an inevitable consequence of respiration and exacerbated by the inflammatory response and by exogenous factors...
-
The optimisation of analytical parameters for routine profiling of antioxidants in complex mixture by HPLC coupled post-column derivatisation
PublicationIntroduction: The wide application of natural and artificial antioxidants in food, cosmetic and pharmaceutical industry as well as the recognition of the importance of food antioxidants for supporting human health created demand for reliable and industrially applicable methods of determining antioxidative activity. This requirement can be fullfilled with the recently proposed HPLC-post-column derivatisation approach enabling the...
-
Influence of nonlinearities on the efficiency and accuracy of FEM calculations on the example of a steel build-up thin-walled column
PublicationDue to the increase of computing capabilities of standard processing units, it is possible to perform complex analyses, considering a number of nonlinearities, such as geometric, material and boundary (contact) even on personal computers. In the paper, the authors have analysed the efficiency and accuracy of standard PC’s FEM calculations performed in Abaqus CAE 2017 software on the example of a critical load assessment of a thin-walled...
-
Comparison of bacterial production in the water column between two Arctic fjords, Hornsund and Kongsfjorden (West Spitsbergen)
PublicationBacterial production and the accompanying environmental factors were measured in the water columns of two Arctic fjords during the cruise in July and August 2013. Water samples were collected at six stations located in the central part of Hornsund and Kongsfjorden. In Hornsund, where average water temperatures were 1.25-fold lower than in Kongsfjorden, the bacterial production was twice as high (0.116 ± 0.102 vs 0.05 ± 0.03 mg...
-
Investigations of local/global buckling of cylindrical metal silos with corrugated sheets and open-sectional column profiles
PublicationArtykuł zajmuje się problemem lokalnego/globalnego wyboczenia w cylindrycznych metalowych silosach z blachy falistej z otwartymi cienkościennymi profilami słupowymi. Obliczenia wykonano w ramach liniowej teorii bifurkacji stosując metodę elementów skończonych w programie ABAQUS. Zbadano obszernie wpływ różnych parametrów (średnica i wysokość silosów, grubość blachy falistej, wielkość fali blachy, rozstaw słupów, przekrój słupów)...
-
Wpływ parametrów procesowych na wielkość powierzchni międzyfazowej generowanej w kolumnie do współprądowej flotacji białek serwatkowych
PublicationPrzeprowadzono badania wpływu parametrów procesowych na wielkość pęcherzy powietrza i stopień zatrzymania gazu we współprądowej kolumnie barbotażowej do flotacji białek serwatkowych. Stwierdzono, że na wielkość powierzchni międzyfazowej gaz-ciecz można wpływać poprzez zmianę: prędkości przepływu gazu, pH roztworu oraz w wyniku wprowadzenia do roztworu substancji powierzchniowo czynnych palmitynianu sodu i cytrynianu trietylu.
-
Stability of cylindrical steel silos composed of corrugated sheets and columns based on FE analyses versus Eurocode 3 approach
PublicationComprehensive static and dynamic 3D stability finite element analyses of a cylindrical steel silo composed of corrugated sheets and open thin-walled vertical stiffener profiles were carried out by taking the geometric and material non-linearity into account. The silowas subjected to axisymmetric and non-axisymmetric loads imposed by a bulk solid following Eurocode 1. Theoretical and measured initial geometric imperfections were...
-
Determination of buckling strength of silos composed of corrugated walls and thin-walled-columns using simplified wall segment models
PublicationW artykule przedstawiono wyniki obszernych analiz numerycznych wyboczenia i stateczności metalowych silosów z blachy falistej wzmocnionych cienkościennymi słupami. Wykonano analizy liniowe i nieliniowe. Do obliczeń zaproponowano proste modele segmentów ścian zamiast skomplikowanych modeli całych silosów. Otrzymano bardzo dobrą zgodność wyników numerycznych. Wyniki obliczeń numerycznych porównano dodatkowo z wynikami normowymi.
-
Kontrola procesu wytwarzania biowodoru z gliceryny podczas fermentacji beztlenowej
PublicationProdukcja wodoru z biomasy z wykorzystaniem procesów biologicznych jest korzystną ekonomicznie alternatywą w porównaniu do otrzymywania wodoru np. na drodze zgazowania, pirolizy, czy przez rozkład biomasy w warunkach nadkrytycznych. Wśród biologicznych procesów otrzymywania wodoru, za najbardziej obiecującą uważa się ciemną fermentację wodorową, w której substraty organiczne są przekształcane bez udziału światła przez bakterie...
-
Akumulacja tlenu w zawiesinie drożdży Saccharomyces cerevisiae w kolumnach barbotażowych i reaktorach airlift z cyrkulacją zewnetrzną
PublicationBadano wpływ prędkości powietrza oraz stężenia drożdży Saccharomyces cerevisiae w zawiesinie na mierzone metodą dynamiczną stężenie tlenu rozpuszczonego w cieczy w czasie napowietrzania. Wskazano na konieczność odróżniania szybkości akumulacji tlenu oraz szybkości wnikania tlenu gaz-ciecz mierzonego w ten sposób. Badania przeprowadzono w zawiesinach drożdży aktywnych oraz zdezaktywowanych.Stwierdzono, że objętościowy współczynnik...
-
Querelle Des Femmes. Male and Female Voices in Italy and Europe, Szczecin, Volumina Pl, ISBN 978-83-7867-2
Publication -
Reemission of inorganic pollution from permafrost? A freshwater hydrochemistry study in the lower Kolyma basin (North-East Siberia)
PublicationPermafrost regions are under particular pressure from climate change resulting in widespread landscape changes, which impact also freshwater chemistry. We investi- gated a snapshot of hydrochemistry in various freshwater environments in the lower Kolyma river basin (North-East Siberia, continuous permafrost zone) to explore the mobility of metals, metalloids and non-metals resulting from permafrost thaw. Partic- ular attention...
-
Production of tropane alkaloids in Hyoscyamus niger (black henbane) hairy roots grown in bubble-column and spray bioreactors
PublicationHairy root cultures of Hyoscyamus niger were cultivated in shake-flasks, a bubble-column bioreactor and a hybrid bubble-column/spray bioreactor and evaluated for alkaloid production.
-
Chemometric outlook on correlations between retention parameters of polar and semipolar HPLC columns and physicochemical characteristics of ampholytic substances of biological and pharmaceutical relevance
Publication -
Chemometric approach to correlations between retention parameters of non-polar HPLC columns and physicochemical characteristics for ampholytic substances of biological and pharmaceutical relevance
Publication -
Fixed-bed adsorption of chlorinated hydrocarbons from multicomponent aqueous solution onto activated carbon: Equilibrium column model
Publication -
Characteristics of calcium carbonate microparticles fabricated by the emulsion-emulsion technique in a large scale
PublicationReaktor zbudowany z dwóch współosiowych kolumn z mieszaniem w kolumnie wewnętrznej zastosowano do strącania cząstek węglanu wapnia metodą mieszania dwóch emulsji woda w oleju zawierających chlorek wapnia oraz węglan sodu jako reagenty. Zbadano wpływ częstości obrotów mieszadła, stężenia reagentów oraz czasu starzenia na wielkość cząstek stałych.
-
Characterization of 1,3-alternate calix[4]arene-silica bonded stationary phases and their comparison to selected commercial columns by using principal component analysis
PublicationTwelve calix[4]arene stationary phases in 1,3-alternate conformation, synthesized in the authors laboratory, were characterized in terms of their surface coverage, hydrophobic selectivity, aromatic selectivity, shape selectivity, hydrogen bonding capacity and ion-exchange capacity. The set of tests commonly used for evaluation of commercially available stationary phases was applied to assess fundamental chromatographic properties...