Filters
total: 1322
filtered: 1132
displaying 1000 best results Help
Search results for: STEEL GRANDSTAND
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublicationThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Safety of erection and repair of steel tanks with geometric imperfections using heavylift jack-up system
PublicationSafety analysis is performed of cylindrical vertical steel tanks during erection using heavylift jack up system. During an assembly or repair process a set of hydraulic supports is used. It allows to use the in-place lifting of heavy steel constructions on the required height. Wind can strongly influence stability of the lifted tank. Any geometric imperfections can reduce the critical or limit load. In the work failures of the...
-
Cyclic deformation and fracture behaviour of additive manufactured maraging steel under variable-amplitude loading
PublicationThe cyclic deformation and fracture behaviour of 18Ni300 maraging steel produced by laser beam powder bed fusion is studied under variable-amplitude loading. The tests were conducted under fully-reversed strain-controlled conditions with a loading sequence comprising three ascending cycles and three descending cycles repeated sequentially until failure. After the tests, fracture surfaces were examined using height and volume surface...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublicationThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
Corrosion behavior of vacuum sintered duplex stainless steels
Publication -
The corrosion resistance of laser surface alloyed stainless steels
Publication -
Environmental degradation of the Cr-Mo steels in liquid hydrocarbons
PublicationPrzedstawiono podatność stali stopwych 26H2MF i 34HNM do naprężeniowego pękania korozyjnego. Środowiskiem do badań było paliwo ciężkie i zużyty olej mineralny.
-
Hydrogen degradation of structural steels in technical hydrocarbon liquids
PublicationDla stali stopowych przeprowadzono badania absorpcji wodoru, mechaniczno-korozyjne przy stałej małej prędkości odkształcania, przy stałym obciążeniu i przy obciążeniu cyklicznie-zmiennym. Środowiskiem było paliwo kotłowe, przepracowany olej mineralny oraz gliceryna. Stwierdzono, iż pochłonięty wodór nie powoduje przedwczesnego zniszczenia stali poddanych działaniu stałego obciążenia ponizej granicy plastyczności oraz, że zaabsorbowany...
-
Hydrogen degradation of high strength low alloyed steels.
PublicationBadano wpływ polaryzacji katodowej na własności stali węglowej, stali o podwyższonej i wysokiej wytrzymałości metodą stałego powolnego odkształcania.Stwierdzono, że stopień kruchości wodorowej każdej z badanych stali zależał od stężenia wodoru dyfuzyjnego.
-
Investigations of welded joints of dissimilar heat resistant steels.
PublicationPrzeprowadzono badania metalograficzne połączeń spawanych różnorodnych stali żarowytrzymałych rur o przekroju 31,8x7,1 mm ze stali 10H2M z blachą ze stali 20H23N18. Badania makro- i mikrostruktury złączy spawanych wykazały, że istotnym czynnikiem wpływającym na właściwości mechaniczne złącza jest obecność wad takich jak pory lub wtrącenia żużla. Te nieciągłości w materiale powodują koncentrację naprężeń i powstawanie mikropęknięć.
-
Hydrogen degradation of high-strength weldable steels in seawater
PublicationOceniono podatność na niszczenie wodorowe stali spawalnych o wysokiej wytrzymałości przy obciążeniach monotonicznie rosnących. Badano dwa gatunki stali ulepszonych cieplnie i ich złącza spawane. Przeprowadzono próby rozciągania z małą prędkością odkształcania w wodzie morskiej przy polaryzacji katodowej. Wykonano próby przenikania wodoru metodą Devanathana-Stachurskiego.
-
Hydrogen delayed cracking of high-strength weldable steels
PublicationOceniano podatność na niszczenie wodorowe stali 14HNMBCu o wysokiej wytrzymałości i jej połączeń spawanych przy obciążeniu stałym w wodzie morskiej. Badania przeprowadzono w powietrzu, oraz w środowisku wody morskiej przy potencjale korozyjnym i przy polaryzacji katodowej. Obecność lub brak opóźnionych pęknięć próbek z karbem przyjęto za miarę odporności na niszczenie wodorowe przy stałym obciążeniu.
-
Weldability of high strength steels in wet welding conditions
PublicationIn this paper are characterized problems of high strength steel weldability in underwater wet welding conditions. Water as a welding environment intensifies action of unfavourable factors which influence susceptibility to cold cracking of welded steel joints. The susceptibility to cold cracking of S355J2G3 steel and S500M steel in wet conditions was experimentally estimated (by using Tekken test). It was concluded that the steels...
-
The Application of Cluster Analysis in the Assessment of the Weldability of Unalloyed Steels
PublicationNon-alloy steels constitute a large group of steels characterised by diversified chemical composition, structural morphology and a wide range of mechanical properties (determining weldability). The paper presents results of multidimensional analyses (based on cluster analysis) of 110 selected unalloyed steel grades. Properties adopted as diagnostic features included the chemical composition, mechanical properties (yield point)...
-
Influence of process of straightening ship hull structure made of 316L stainless steel on corrosion resistance and mechanical properties
PublicationThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries, for architectural elements, and many others. The chemical composition of corrosion-resistant...
-
Strengthening mechanism and precipitate evolution of a multi-application special engineering steel designed based on a hybrid idea
Publication -
Fatigue Damage Development in 14MoV6-3 Steel for Power Plant Pipes Monitored by Digital Image Correlation
Publication -
The effect of long-term service at elevated temperatures on structure and mechanical properties of Cr-Mo-V steel
PublicationPurpose: of this paper is to reveal the microstructural changes in 13HMF steel exposed to long-term service at elevated temperatures. The degradation of bainite structure was determined and carbides morphology has been examined. The influence of carbides evolution was discussed in dependence of creep rupture strength and mechanical properties of the steel.
-
Complex Corrosion Properties of AISI 316L Steel Prepared by 3D Printing Technology for Possible Implant Applications
Publication -
Surface Layer Properties of Sintered Ferritic Stainless Steel Remelted and Alloyed with FeNi and Ni by HPDL Laser
Publication -
Laser Thermal Oxidation by Ytterbium-Doped Fibre Laser of the Hot and Cold-Rolled Stainless Steel Surface
Publication -
Wear of carbide inserts during turning of C45 steel in dry cutting conditions and in presence of emulsion mist
Publication -
Formation of Surface Topography During Turning of AISI 1045 Steel Considering the Type of Cutting Edge Coating
Publication -
Niszczenie wodorowe złączy spawanych ze stali S355 = Hydrogen degradation of welded joints of S355 steel
PublicationW artykule przedstawiono ocenę podatności na niszczenie wodorowe złączy spawanych ze stali S355. Jako parametry niszczenia wodorowego wybrano względne wartości energii zniszczenia, wydłużenia, przewężenia i wytrzymałości na rozciąganie. Parametry te wyznaczono w próbie odkształcania z małą prędkością na próbkach okrągłych, gładkich. Stwierdzono, że stal S355w środowisku kwaśnym podczas polaryzacji katodowej, jest bardziej skłonna...
-
Numerical analysis of influence of intermediate stiffeners setting on the stability behaviour of thin-walled steel tank shell
Publication -
Evaluation of cavitation erosion-corrosion degradation of mild steel by means of Dynamic Impedance Spectroscopy in galvanostatic mode
PublicationPrzedstawiono wyniki badań degradacji stali węglowych na skutek oddziaływania erozji-korozji kawitacyjnej. Do analizy wykorzystano technikę Dynamicznej Elektrochemicznej Spektroskopii Impedancyjnej w trybie galwanostatycznym, bliżej odwzrorowującym warunki naturalne. Do oceny stopnia degradacji posłużyły również funkcja ubytku masy MDPR oraz obrazy mikroskopowe SEM. Potwierdzono wpływ łączonej degradacji erozyjno-korozyjnej na...
-
The Influence of Gas Mixture in the Glow-Discharge Nitriding Process of Austenitic Stainless Steel on Characteristic of Nitrided Cases
PublicationAustenitic stainless steels characterize with excellent corrosion resistance, although low mechanical properties. In many cases that limits their exploitation in industrial applications. Moreover, austenitic stainless steel is susceptible to local corrosion in the presence of halide ions. In present works, it was emphasized that the nitriding of austenitic stainless steels gives some potential abilities to obtain beneficial effect...
-
Evaluation of cavitation erosion–corrosion degradation of mild steel by means of dynamic impedance spectroscopy in galvanostatic mode
Publication -
Experimental validation of the use of energy transfer ratio (ETR) for damage diagnosis of steel-concrete composite beams
Publication -
Comparison of properties of magnetoacoustic emission and mechanical Barkhausen effects for P91 steel after plastic flow and creep
PublicationW artykule przedstawiono wyniki pogłębionej analizy sygnału szumowego efektu Barkhausena dla próbek ze stali krzemowej Fe-2%Si po deformacji plastycznej. Badane były próbki po walcowaniu na zimno powodującym odkształcenie względne w zakresie do 8%. Pierwsze podejście polegało na analizie w dziedzinie czasu widma badanego sygnału. Analiza ta została uzupełniona o analizę liczby zliczeń impulsów w funkcji napięcia progowego, zarówno...
-
Experiments and Numerical Simulations of the Annealing Temperature Influence on the Residual Stresses Level in S700MC Steel Welded Elements
Publication -
Appliance of High Speed Camera during Industrial Exploitation on the Example of Static and Dynamic Tests of Steel Probes
Publication -
Effect of high temperature exposure on the fatigue damage development of X10CrMoVNb9-1 steel for power plant pipes
Publication -
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. On the heat transfer surface of heat exchanger the metallic porous layer was created. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Impact of eddy currents on Barkhausen and magnetoacoustic emission intensity in a steel plate magnetized by a C-core electromagnet.
PublicationZbadano (zmierzono i modelowano metodą elementów skończonych) wpływ częstości magnesowania na przestrzenny i czasowy rozkład indukcji magnetycznej wewnątrz płyty stalowej. Wyznaczono i zmierzono natężenie polowego rozkładu Barkhausena (HEB) na powierzchni płyty oraz natężnie emisji magnetoakustycznej (EMA) z całej magnesowanej objętości. Wykazano, iż obserwowane zmiany w natężeniu HEB i EMA są wynikiem zmian w rozkładzie indukcji...
-
Chained machine learning model for predicting load capacity and ductility of steel fiber–reinforced concrete beams
PublicationOne of the main issues associated with steel fiber–reinforced concrete (SFRC) beams is the ability to anticipate their flexural response. With a comprehensive grid search, several stacked models (i.e., chained, parallel) consisting of various machine learning (ML) algorithms and artificial neural networks (ANNs) were developed to predict the flexural response of SFRC beams. The flexural performance of SFRC beams under bending was...
-
Application of the theory of energy transformation systems to fatigue assessment of steel elements under multiaxial periodic loading
PublicationPraca dotyczy symulacji odporności zmęczeniowej elementów stalowych poddanych wieloosiowym obciążeniom okresowym w zakresie wysokocyklowym. W tym celu zdefiniowano jednoosiowe naprężenie sinusoidalne, równoważne w sensie trwałości zmęczeniowej materiału naprężeniu aktualnemu gdy każda jego kartezjańska składowa jest dana w postaci szeregu Fouriera. Warunki równoważności wynikają z teorii systemów transformacji energii i wiążą się...
-
Development and experimental validation of a novel double-stage yield steel slit damper-buckling restrained brace
PublicationThis research is focused on the development and experimental validation of a novel double-stage yield steel slit damper-buckling restrained brace (SSD-DYB) system designed for seismic resistance of steel structures. The SSD-DYB integrates the energy dissipation capability of a steel slit damper (SSD) in its initial segment, enhancing performance in the case of lower seismic intensities levels while employing a larger segment for...
-
Wpływ obróbki cieplnej na strukturę stali krzemowej. The heat treatment influence on the silicon steel morphology
PublicationStal sprężynową 55S2 poddano obróbce cieplnej przy poprawnych i zawyżonych paramatrach temperaturowo-czasowych. Dla materiału o wadliwej strukturze wyjściowej, dobór wyższych temperatur i czasów obróbki pozwolił na otrzymanie bardziej poprawnych struktur i własności materiału.
-
Evaluation of hydrogen degradation susceptibility of high-strength weldable steel subjected to cathodic polarization in sea-water
PublicationOcenę podatności stali spawalnych o wysokiej wytrzymałości ich złączy spawanych na kruchość wodorową przeprowadzono z wykorzystaniem próby rozciągania ze stałą, niską szybkością odkształcenia w środowisku wody morskiej przy polaryzacji katodowej. Wykonano próby elektrochemiczne przenikania wodoru w wodzie morskiej dla oceny dyfuzji i pułapkowania wodoru. Badano wpływ bakterii redukujących siarczany na absorpcję wodoru w środowisku...
-
Instantaneous Impedance Analysis of Non-Stationary Corrosion Process: a Case Study of Carbon Steel in 1M HCl
PublicationThe paper concerns the problem of evaluation of stationarity of carbon steel corrosion in 1M HCl. Comparison of corrosion rate with addition of corrosion inhibitor to the reference measurement is the most often used way of evaluating inhibitor efficiency. Such an approach is valid only if corrosion rate is a stationary process. Two complementary techniques were used simultaneously: volumetric analysis of evolved hydrogen and instantaneous...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Effect of Thermal Shock During Legionella Bacteria Removal on the Corrosion Properties of Zinc-Coated Steel Pipes
PublicationThe purpose of this investigation was to conduct the failure analysis of a water-supply system made from zinc-coated steel. The observed corrosion process had an intense and complex character. The brownish deposits and perforations were present after 2-3 years of exploitation. The electrochemical study based on the Tafel polarization, corrosion potential monitoring, and electrochemical impedance spectroscopy together with microscopic...
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublicationCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Qualification of brazing procedure for furnace brazing of austenitic steel according to requirements of the ASME BPVC section IX
PublicationThe article presents the procedure for qualifying brazing technology in a vacuum furnace on the example of stainless steel elements joined with copper filler material from the F-No group. 105, in accordance with the ASME Sec. IX, part QB (ASME Boiler and Pressure Vessel Code. Qualification Standard for Welding, Brazing and Fusing; Procedures; Welders; Brazers; and Welding, Brazing and Fusing Operators). The essential variables...
-
Finite element method simulations of various cases of crash tests with N2/W4/A steel road barrier
PublicationThe subject of this study is performance of N2/W4/A steel road safety barrier investigated in numerical simulations. System was checked under several types of initial conditions, which were assumed basing on the TB11 and TB32 normative crash tests. The main goal of present study is to investigate the relationship between initial conditions (angle and velocity) of the impact and the severity indices (associated to the vehicle occupant) during...
-
Influence of nonlinearities on the efficiency and accuracy of FEM calculations on the example of a steel build-up thin-walled column
PublicationDue to the increase of computing capabilities of standard processing units, it is possible to perform complex analyses, considering a number of nonlinearities, such as geometric, material and boundary (contact) even on personal computers. In the paper, the authors have analysed the efficiency and accuracy of standard PC’s FEM calculations performed in Abaqus CAE 2017 software on the example of a critical load assessment of a thin-walled...
-
Load-carrying capacity of axially loaded concrete-filled steel tubular columns made of thin tubes
PublicationAn experimental investigation was conducted on 30 CFST columns. An influence of the following factors on load-carrying capacity of the investigated columns was analyzed: the column slenderness (l1 = 42, l2 = 27 and l3 = 15), the tube thickness (the reinforcement ratio was equal to 4% or 6%), the way of applying the load to CFST columns (through the concrete core or through the entire cross-section), the bond strength between a...
-
Analysis of load carrying capacity and destruction mechanism of an intermediate anchorage steel plate for pillar jib crane
PublicationPillar jib cranes are often mounted to existing floors with the use of an intermediate anchorage steel plate instead of using independent foundations, what is shown in the figure. Standards for steel design provide only basic rules for the design of such an intermediate plate. This study presents a simple design approach by using a numerical model in order to analyze different parameters that have significant influence in the anchorage...
-
Influence of PWHT Parameters on the Mechanical Properties and Microstructural Behavior of Multi-Pass GTAW Joints of P92 Steel
PublicationThe 9% Cr steels were developed for ultra-supercritical (USC) power plants to meet the requirements of high operating temperature and pressure. These steels are produced to operate at high temperatures where impact toughness is not a concern; however, it becomes important for the welded joints to have good impact toughness at room temperature for manufacturing. The present work investigates the effect of the post-weld heat treatment...