Search
Filters
total: 997
-
Catalog
Search results for: CLOUD MANUFACTURING
-
Integrated production technology of cylindrical surfaces by turning and burnishing
PublicationThe method is based on a combination of previously used two separate operations namely machining and burnishing in a one complex operation implemented on a lathe.In the case of machining shafts and hydraulic cylinders of steel C45 is possible to obtain a surface roughness Ra=0,16 - 0,32 micrometers, dimensional accuracy class 7-8 according to ISO standards, and increase in the hardness of the surface up to 40%.
-
Sliding burnishing technology of holes in hardened steel
PublicationNew technology with sliding burnishing of holes with cylindrical surface, made of hardened steel /60 HRC/, is presented in the paper.After burnishing operation on hole diameter 30 mm in satellite gear wheel the surface roughness parameter Ra=0,02-0,04 micrometers was obtained. The method and results of research as technological conclusion are presented.
-
The preferable ways of decision-making in IT teams
PublicationSoftware development team collaboration requires various decisions regarding essential aspects of a project’s progress. General and particular decision-making models are considered, and their main aspects such as team types, problem solving categories, and decision-making ways are analyzed. The research concerns representative groups of IT specialists and their preferences in decision-making are investigated. Four possible cases were...
-
Modeling of Surface Roughness in Honing Processes by UsingFuzzy Artificial Neural Networks
PublicationHoning processes are abrasive machining processes which are commonly employed to improve the surface of manufactured parts such as hydraulic or combustion engine cylinders. These processes can be employed to obtain a cross-hatched pattern on the internal surfaces of cylinders. In this present study, fuzzy artificial neural networks are employed for modeling surface roughness parameters obtained in finishing honing operations. As...
-
METODY DOSKONALENIA SYSTEMU ZARZĄDZANIA ŚRODOWISKOWGO ISO14001 W PRZEDSIĘBIORSTWACH PRODUKCYJNYCH
PublicationOpracowanie ma na celu przedstawienie problematyki doskonalenia zarządzania środowiskowego w przedsiębiorstwach produkcyjnych. W opracowaniu przedstawiono główne wymagania w obszarze doskonalenia systemu zarządzania środowiskowego zgodnego z wymaganiami ISO14001. Zaprezentowano wybrane metody oraz mechanizmy doskonalenia systemów zarządzania środowiskowego ISO14001 stosowane w praktyce. Dokonano prezentacji autorskiej metody doskonalenia...
-
Selected aspects of logistics management of the production process in an enterprise
PublicationThe following article presents selected aspects of management of production logistics process in enterprise. Companies treat this part of business as a way to empower market position. In the first part author explained the idea of process. The next part describes the definition of logistics production management, which is crucial for manufacturing enterprises. However, author described lots of tools related to production management...
-
ARTIFICIAL MODEL IN THE ASSESSMENT OF THE ALGORITHM OF OBJECTS RECORDED BY LASER SCANNING SHAPE DETECTION (ALS/TLS)
PublicationBrief description of the study and used methods. Brief description of the study and used As part of the preparatory work aimed to create the application solution allowing for the automation of searching objects in data, obtained in the scanning process using ALS (Airborne Laser Scanning) or TLS (Terrestrial Laser Scanning), the authors prepared a artificial (synthetic, theoretical) model of space, used for the verification of operation...
-
Artur Sitko dr inż.
People -
Piotr Sender dr inż.
People -
Joanna Sypniewska mgr inż.
PeoplePhD student in the field of materials engineering at Gdansk University of Technology. Working on laser surface modification of titanium alloys for biomedical applications
-
Monitoring of single-side lap grinding with electroplated tools
PublicationThe results presented in the paper show that utilising microphones as audible sound sensors is a suitable approach for monitoring a single-side lap grinding process due to the low levels of noise generated by the drives of a machine tool. The results confirm that sound signal analysis is a feasible and relatively simple method to monitor a lap grinding process with the use of an audible sound sensor. Proposed method can be used...
-
Influence of the laser remelting parameters on the thickness of surface layers created on the stainless steel X5CrNi18-10
PublicationIn this work the surface of austenitic stainless steel type X5CrNi18-10 was treated by using laser. Laser remelting was done by means of laser MLT 2500 CO2 with different parameters of treatment: P - power beam (800 [W], 1000 [W], 1100 [W], 1200 [W]); v - scanning velocity (6 [mm/s], 7 [mm/s], 8 [mm/s]); diameter of laser beam (1.4 [mm], 1.6 [mm]). The influence of these parameters on the thickness and shape of layers in manufacturing...
-
A High-Efficient Low-Voltage Rectifier for CMOS Technology
PublicationA new configuration of rectifier suiting CMOS technology is presented. The rectifier consists of only two nchannel MOS transistors, two capacitors and two resistors; for this reason it is very favourable in manufacturing in CMOS technology. With these features the rectifier is easy to design and cheap in production. Despite its simplicity, the rectifier has relatively good characteristics, the voltage and power efficiency, and...
-
Planning a Cost-Effective Delay-Constrained Passive Optical Network for 5G Fronthaul
PublicationWith the rapid growth in the telecommunications industry moving towards 5G and beyond (5GB) and the emergence of data-hungry and time-sensitive applications, Mobile Network Operators (MNOs) are faced with a considerable challenge to keep up with these new demands. Cloud radio access network (CRAN) has emerged as a cost-effective architecture that improves 5GB performance. The fronthaul segment of the CRAN necessitates a high-capacity...
-
Framework for extracting rails and setting-out railway line axis based on UAV photogrammetric measurements
PublicationTechnical diagnostics enables assessing the current technical condition of a railway line and adjacent infrastructure, and forecasting its changes over a specific time horizon. One of its elements is the periodic monitoring of rail position and their geometry. This article presents a new framework for the setting-out of a railway track axis. The process presented in the manuscript is based on the specific filtration and extraction...
-
PBDEs in environmental samples: Sampling and analysis
PublicationThe paper reviews the subject literature concerning analytical procedures routinely sed for monitoring polybrominated diphenyl ethers (PBDE) in environmental samples. It describes and summarizes subsequent stages of analytical procedure including sample collection and preparation, extraction, clean-up and final determination. Different approaches with their advantages and limitations are presented. Special attention is drawn to...
-
Review of the Complexity of Managing Big Data of the Internet of Things
PublicationTere is a growing awareness that the complexity of managing Big Data is one of the main challenges in the developing feld of the Internet of Tings (IoT). Complexity arises from several aspects of the Big Data life cycle, such as gathering data, storing them onto cloud servers, cleaning and integrating the data, a process involving the last advances in ontologies, such as Extensible Markup Language (XML) and Resource Description...
-
Photogrammetry image-based approach for imperfect structure modelling and FE analysis
PublicationThis study aims to model and analyse imperfect tructures using real measurements, employing photogrammetry technique commonly used in the geodesy. The study highlights the capability of the photogrammetry in aiding the structural analysis of imperfect engineering objects. Firstly, the photogrammetry measurements of a stiffened plate are carried out using a specially designed for the purpose experimental stand. Then, the plate surface...
-
ZARZADZANIE ORGANIZACJĄ TYPU SMART
PublicationZaprezentowano organizacji, w której charakterystykę wpisano następujące cechy: strategiczne uwarunkowanie, maksymalną innowacyjność, atrakcyjność dla interesariuszy, rozwijanie osobowości pracowników oraz twórczość w działaniu. Te atrybuty, tworzą koncepcję organizacji SMART (akronim od pierwszych liter powyższych cech), która wyróżnia się dodatkowo strukturą opartą o dynamicznie kreowane zespoły oraz skutecznym wspomaganiem...
-
Reduction in Errors in Roughness Evaluation with an Accurate Definition of the S-L Surface
PublicationCharacterization of surface topography, roughly divided into measurement and data analysis, can be valuable in the process of validation of the tribological performance of machined parts. Surface topography, especially the roughness, can respond straightly to the machining process and, in some cases, is defined as a fingerprint of the manufacturing. When considering the high precision of surface topography studies, the definition...
-
Rotational Molding of Linear Low-Density Polyethylene Composites Filled with Wheat Bran
PublicationApplication of lignocellulosic fillers in the manufacturing of wood polymer composites (WPCs) is a very popular trend of research, however it is still rarely observed in the case of rotational molding. The present study aimed to analyze the impact of wheat bran content (from 2.5 wt.% to 20 wt.%) on the performance of rotationally-molded composites based on a linear low-density polyethylene (LLDPE) matrix. Microscopic structure...
-
Selected Aspects of 3D Printing for Emergency Replacement of Structural Elements
PublicationThe paper presents a synthetic characterization of modern methods of manufacturing or regenerating machine elements. Considered methods are machining and additive methods, in particular 3D printing in the FDM/FFF technique. For the study, the authors made samples of the holder bracket using selected methods. Samples made by machining operations, 3D printing with various filling were tested. The paper contains a technical and economic...
-
Recent Advances in Loop Heat Pipes with Flat Evaporator
PublicationThe focus of this review is to present the current advances in Loop Heat Pipes (LHP) with flat evaporators, which address the current challenges to the wide implementation of the technology. A recent advance in LHP is the design of flat-shaped evaporators, which is better suited to the geometry of discretely mounted electronics components (microprocessors) and therefore negate the need for an additional transfer surface (saddle)...
-
Green and Sustainable Membranes: A review
PublicationMembranes are ubiquitous tools for modern water treatment technology that critically eliminate hazardous materials such as organic, inorganic, heavy metals, and biomedical pollutants. Nowadays, nano-membranes are of particular interest for myriad applications such as water treatment, desalination, ion exchange, ion concentration control, and several kinds of biomedical applications. However, this state-of-the-art technology suffers...
-
Multi-Criterial Design of Antennas with Tolerance Analysis Using Response-Feature Predictors
PublicationImperfect manufacturing is one of the factors affecting the performance of antenna systems. It is particularly important when design specifications are strict and leave a minimum leeway for a degradation caused by geometry or material parameter deviations from their nominal values. At the same time, conventional antenna design procedures routinely neglect to take the fabrication tolerances into account, which is mainly a result...
-
Wykorzystanie narzędzi pracy zdalnej w działaniach Koła Naukowego Konstruktorów Pojazdów
PublicationNiniejszy artykuł stanowi opis działalności Koła Naukowego Konstruktorów Pojazdów, w którego działaniach wykorzystywane są nowoczesne narzędzia pracy zdalnej. Dzięki takiemu podejściu, możliwe staje się wyeliminowanie niedogodnień, z którymi borykano się stosując standardowe, starsze podejście do realizacji zadań projektowych w jednostkach badawczo-rozwojowych. Podane przykłady ilustrują, w jaki sposób powszechny obecnie dostęp...
-
Anna Wałek dr
PeopleDr Anna Wałek, President of IATUL – International Association of University Libraries, director of the Gdańsk University of Technology Library. An experienced library manager, an expert in the field of Open Science, and organization and management of a scientific library. She conducts scientific research in data management in various scientific disciplines, metadata for research data, and data management support services - incl....
-
CEE Trade in Services: Value-Added Versus Gross Terms Approaches
PublicationThis article assesses the impact of the determinants of service exports in both value-added terms and gross terms for seven Central Eastern European economies in 1995–2011. The results confirm the importance of increasing labor productivity and highly skilled and medium-skilled workers in the growth of trade in services. Exports of services are also supported by linkages between domestic services, especially business services,...
-
Elements of six sigma methodoloygy in polish smes. the pomeranian region context
PublicationIn this article, it has been suggested that the effectiveness of the design and implementation of the process approach in the SMEs sector affects the effectiveness and efficiency of the application of elements of the Six Sigma ™ concept. The selected results of the research have been presented to answer the question to what extent small and medium-sized manufacturing, service and production - service companies in Pomeranian region...
-
Issues of Measuring the Course of Batch Production Processes
PublicationIn order to meet demands induced by development of manufacturing processes and production systems, new criteria and indicators that would allow a multiple aspect and realistic rating of batch production process courses are necessary. The objective of this paper is to present the correlation between production processes measurement, its rating and production control, basing on case study analysis from production enterprise. A new...
-
Quality 5.0: A Paradigm Shift Towards Proactive Quality Control in Industry 5.0
PublicationIndustry 5.0, the latest wave of industrial revolution, is redefining the traditional manufacturing and production landscapes by leveraging advanced technologies, promoting sustainability, and fostering a human-centric approach. An inevitable consequence of this progression is Quality 5.0, the next phase of quality control and assurance. Quality 5.0 aims to transcend the limitations of conventional quality control techniques, which...
-
Magda Rościszewska dr inż.
People -
Karol Kufel mgr inż.
PeopleKarol Kufel has been working at the Faculty of Management and Economics GUT since 2010. Since 2014, he has been an assistant in the Department of Management in Industry. He graduated from the Faculty of Mechanical Engineering GUT in the specialty of Robotics and the Faculty of Management and Economics GUT in the specialty of Production Systems Management. His scientific and research interests have been focused on the design and...
-
The circle object detection with the use of Msplit estimation
PublicationThe paper presents the use of Msplit(q) - estimation in the filtration and aggregation of point clouds containing a known number of elliptical shapes with preliminary unknown - locations and dimensions. These theoretical solutions may have practical relevance especially in the modelling of terrestrial laser scanning data of objects that have similar shape to circles. Mentioned shapes can be scanned of tree trunks, columns, gutters,...
-
Wymagania inżynierii systemów dla maszyn wirujących (PG-00060237)
e-Learning CoursesTurbiny wiatrowe, gazowe, mikroturbiny, silniki lotnicze, turbosprężarki i inne systemy mechaniczne to przykłady maszyn wirujących, które wymagają wysoko wykwalifikowanych inżynierów. Powinni oni zrozumieć złożoność procesów projektowania i produkcji, w tym wytwarzania przyrostowego, oraz konserwacji prognostycznej opartej na inżynierii cyfrowej dla bezawaryjnej pracy silnika. Kurs zapewnia fundamentalną wiedzę wymaganą w przemyśle...
-
A new method of presosns identification based on comparative analysis of 3D face models
PublicationThe article presents the use of modern close range photogrammetry for possessing highly accurate 3D models of the human face (including the ears). Modern methods used to obtain precise data describing the construction of a human face, and even the whole human body, should allow to get finished measurement material in a very short time. Those features belong to the optical scanning technology. Comparative analysis of models of the...
-
Weighted Clustering for Bees Detection on Video Images
PublicationThis work describes a bee detection system to monitor bee colony conditions. The detection process on video images has been divided into 3 stages: determining the regions of interest (ROI) for a given frame, scanning the frame in ROI areas using the DNN-CNN classifier, in order to obtain a confidence of bee occurrence in each window in any position and any scale, and form one detection window from a cloud of windows provided by...
-
Paintings
PublicationThe painting as a curtain (...) A contradiction is therefore what constitutes a painting, and ambiguity is its right. As a young artist, I intuitively defined the work of art as a boundary. Over the years that intuition changed into a conviction that the particular form of art which is painting at the same time reveals and hides; it exists at this intersection of functions as a see-through curtain. We don’t know why there are some...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublicationSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Ocena zastosowania wybranych reguł wymiany narzędzi w systemie produkcyjnym
PublicationIn this paper, an integrated analytical and simulation modelling framework has been developed with the objective to explore total system planning and operational issues. It enables in particular structuring the alternative process flow in manufacturing systems and their extended investigation under different tool exchange rules with limited number of tool inventory. Simulation studies performed with the proposed rules in the environment...
-
Diffusible hydrogen content in deposited metal of multilayer welded joints
PublicationThe article describes manufacturing technology of multilayer joints in terms of control the diffusible hydrogen content. Diffusible hydrogen content in deposited metal for multilayer welded joints made of covered rutile electrodes or covered cellulosic and basic electrodes was determined. It was found that after four beads, the diffusible hydrogen content decreases in the case of the first technology from 36 ml/100 g to 18 ml/100...
-
Decisional DNA based framework for representing Virtual Engineering Objects
PublicationIn this paper, we propose a frame-work to represent the Virtual Engineering Objects (VEO) utilizing Set of Knowledge Experience Structure (SOEKS) and Decisional DNA. A VEO will enable the discovery of new knowledge in a manufacturing unit and the generation of new rules that drive reasoning. The proposed VEO framework will not only be knowledge based representation but it will also have its associated experience embedded within...
-
Smart Innovation Engineering System - A Tool for Facilitating Product Innovation Process
PublicationFor the survival and prosperity of the manufacturing unit, entrepreneurs need to find out new ideas that can be implemented in the products leading to innovation. The current study employs a systematic approach for product innovation. In this approach past experiences based on innovation decisions are stored and recalled during the innovation problem solving process. Implementing this system in the process of product innovation...
-
THE MELT FLOWABILITY AND TENSILE PERFORMANCE OF POLY (-CAPROLACTONE)/BREWERS’ SPENT GRAIN COMPOSITES AS A FUNCTION OF FILLER MODIFICATION
PublicationNowadays, it is essential to reduce the environmental impact of products and technologies. Such an approach should be highlighted in all research activities. In the case of polymer composites, it can be realized by introducing by-products or waste materials as fillers. An auspicious example of such material is the brewers’ spent grain, the major byproduct of the beer production. Its chemical composition, relatively similar to conventional...
-
Manufacturing Techniques 1, W, L, Energy Tech., sem.02, letni22/23
e-Learning Courses -
Manufacturing Techniques 2, WL, Energy Technologies, sem. 3, zimowy, 2023/24
e-Learning CoursesLectures and Laboratories
-
Manufacturing Techniques 1, WL, Energy Technologies, sem. 2, letni, 2023/24
e-Learning CoursesLectures and Laboratories
-
Computer Aided Manufacturing Systems (M:320417W0) (PG_00063000) 2023-24 Summer Semester
e-Learning Courses -
Aleksander Mroziński dr inż.
PeopleAleksander Mroziński is a PhD student at the Faculty of Electronics, Telecommunications and Informatics of the Gdańsk University of Technology. From June 2019 is employed as a metadata editor in the project THE BRIDGE OF DATA. He also participates in three other projects implemented at the Gdańsk University of Technology: InterPhD II, OPUS 13 and PROM. His desire to discover the world motivates him to acquire multidisciplinary...
-
An electric ring thruster as auxiliary manoeuvring propulsion system for watercraft - construction analysis
PublicationThe reported project aimed at examining properties and purposefulness of use of modern electromagneticbearings for a screw propeller in a prototype version of a synchronous ring motor with rare earths magnets.Bearings of this type generate electromagnetic forces which keep the rotor in a state of levitation. Therotating machine with magnetic bearings can work in any environment which reveals diamagnetic properties(air, vacuum,...