displaying 1000 best results Help
Search results for: THE COMPRESIVE STRENGTH
-
Hyperbranched polyethylenimine functionalized silica/polysulfone nanocomposite membranes for water purification
PublicationHyperbranched polyethyleneimine functionalized silica (PEI-SiO2) nanoparticles with considerable hydrophilicity were synthesized and incorporated into a polysulfone (PSF)/dimethylacetamide (DMA)/polyvinylpyrrolidone (PVP) membrane casting solution in five different ratios to fabricate PEI-SiO2/PSF nanocomposite membranes using nonsolvent-induced phase separation. The hydrophilic PEI-SiO2 nanoparticles were characterized by TEM,...
-
Should Polish banks be domesticated?
PublicationThe financial crisis revealed vulnerabilities in the regulation and supervision of the banking system. The overarching goal of the proposal (Bazylea III and CRD IV) is to strengthen the resilience of the EU banking sector. The effects of these regulations will be detrimental to the Polish banking system and economy. This follows from the fact that listed banks in Poland are subsidiaries of international banking groups. The article...
-
Influence of laser processing of the low alloy medium carbon structural steel on the development of the fatigue crack
PublicationThe paper contains the results of the structural analysis, hardness tests and fatigue tests conducted for the medium carbon structural steel with low content of Cr and Ni after its processing with CO2 laser beam. Pre-cracks were made in the round compact tension (RCT) specimen used for fatigue test. Next, four paths, parallel to each other, were melted on both sides of the samples using a laser beam. The paths were perpendicular...
-
The influence of a change in the meniscus cross-sectional shape on the medio-lateral translation of the knee joint and meniscal extrusion
PublicationObjective The purpose of this study was to evaluate the influence of a change in the meniscus cross sectional shape on its position and on the biomechanics of a knee joint. Methods One main finite element model of a left knee joint was created on the basis of MRI images. The model consisted of bones, articular cartilages, menisci and ligaments. Eight variants of this model with an increased or decreased meniscus height were then...
-
Old Problems - New Solutions: Conversion of Capitals as a Tool for Shaping the Competitive Position in the Economic Field
PublicationThe acts and operations any social actor effectuates in each of the logically distinguished spheres of reality are conditioned by many factors, among which a reliable analysis of the strengths and weaknesses of an agent should be considered of utmost importance. The concept of capitals presented in this article divides the quantity of resources available to all acting agents into four main categories (which allows for determining...
-
Old Problems - New Solutions: Conversion of Capitals as a Tool for Shaping the Competitive Position in the Economic Field
PublicationThe acts and operations any social actor effectuates in each of the logically distinguished spheres of reality are conditioned by many factors, among which a reliable analysis of the strengths and weaknesses of an agent should be considered of utmost importance. The concept of capitals presented in this article divides the quantity of resources available to all acting agents into four main categories (which allows for determining...
-
Modelling of laminated glass PVB walls of buildings exposed to vehicle impact with different speeds
PublicationThis paper presents an analytical model, developed for laminated glass subjected to a low-velocity impact. It has the ability to capture glass cracks as well as large non-linear deformations. It is based mathematically on the firstorder deformation concept, which considers the effect of membrane and transverse shear as well as bending. This theory uses damage mechanics to capture the glass cracking. For this purpose, several experiments...
-
The evidence for the impact of policy on physical activity outcomes within the school setting: A systematic review
PublicationPurpose Despite the well-established health benefits of physical activity (PA) for young people (aged 4–19 years), most do not meet PA guidelines. Policies that support PA in schools may be promising, but their impact on PA behavior is poorly understood. The aim of this systematic review is to ascertain the level and type of evidence reported in the international scientific literature for policies within the school setting that...
-
State-of-the-art framework for high-speed camera and photogrammetric use in geometry evaluation of prestressed concrete failure process
PublicationPrestressed structures are a key to the realization of the boldest architectural ideas, regardless of shape complexity, great height and large span. A characteristic feature of the prestressed structure is the better use of concrete material properties by insertion of internal forces. The internal forces are opposed to external loads effects (forces and deformations of structure). Prestressed reinforced concrete beams are characterized...
-
MSRL 2.0. as a new method for research education on urban issues
PublicationThe MSRL 2.0. research is focused on the Baltic Sea Region (BSR) as a multidimensional urban phenomenon with Gdansk acting as a hub for the research teams. The idea of the MSRL 2.0. is to promote the collaboration of professionals and graduate and PhD students by bringing together the mentor(s) with a local research team sharing experiences and proposing strategic recommendations to strengthen sustainable urban development initiatives...
-
Analysis of the Possibilities of Applying 3D Print Methods for the Needs of Ship-Building Industry
PublicationArticle presents the analysis of applying additive and hybrid manufacturing methods and its impact on dynamic stiffness of prepared samples. Dynamic analysis of the handle bracket specimens consisted in plotting the resonance curves and using these curves to estimate the dynamic stiffness of elements produced with additive manufacturing technology. Authors focused especially on 3D print in Fused Deposiotion Modeling/Fused Filament...
-
Direct reduction of pellets through hydrogen: Experimental and model behaviour
PublicationThis paper presents the hydrogen reduction behaviour of industrial pellets designed for the efficient hydrogen based direct reduction. The pellets were provided with very low non ferrous oxides percentage (0.52 of basicity index) and with the absence on TiO2 oxides. The pellets measured diameters in the range 1.14–1.72 cm and were characterized in terms of porosity, pores size, tortuosity and compression strength. The pellets were...
-
Dispersive Micro‐Solid Phase Extraction of Selected Metals in Water and Food Samples Followed by ICP‐OES Analysis: Method Development, Analysis of Real Samples and Greenness Evaluation
PublicationMultiwalled carbon nanotubes (MWCNTs) are well-known adsorbents because of their high surface area, layered and hollow architecture, hydrophobicity, and multiple and easily accessible adsorption sites. In this study, MWCNTs were used for dispersive micro-solid-phase extraction of various metal chelates in environmental and food samples. Different parameters such as concentration of the chelating reagent, the sorbent dosage, the...
-
Biomedical engineering of polysaccharide-based tissue adhesives: Recent advances and future direction
PublicationTissue adhesives have been widely used for preventing wound leaks, sever bleeding, as well as for enhancing drug delivery and biosensing. However, only a few among suggested platforms cover the circumstances required for high-adhesion strength and biocompatibility, without toxicity. Antibacterial properties, controllable degradation, encapsulation capacity, detectability by image-guided procedures and affordable price are also...
-
Numerical analysis on axial capacity of steel built-up battened columns
PublicationThis paper deals with the numerical analysis aimed at study the bearing capacity of pinended steel built-up columns under axial compression. Finite element (FE) models were performed for the columns presented in the literature. The main problem discussed in the article is the shape and magnitude of geometric imperfections introduced into the numerical FE model, necessary to obtain the load capacity consistent with the experimental...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublicationThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
By-Products from Food Industry as a Promising Alternative for the Conventional Fillers for Wood–Polymer Composites
PublicationThe present paper describes the application of two types of food-industry by-products, brewers’ spent grain (BSG), and coffee silverskin (ŁK) as promising alternatives for the conventional beech wood flour (WF) for wood–polymer composites. The main goal was to investigate the impact of partial and complete WF substitution by BSG and ŁK on the processing, structure, physicochemical, mechanical, and thermal properties of resulting...
-
MANDARIN PEEL AS AN AUSPICIOUS FUNCTIONAL FILLER FOR POLYMER COMPOSITES
PublicationThis work describes the application of mandarin peel (MP) as a waste filler for high-density polyethylene (HDPE) composites. The main goal was to investigate the impact of the filler's essential oils, which include multiple terpenes and terpenoids, on the processing, physicochemical, mechanical, and thermal properties of the composites as a function of different filler content (1 – 10 wt%), as well as its effect on the color and...
-
Insights into Compatibilization of Poly(ε-caprolactone)-based Biocomposites with Diisocyanates as Modifiers of Cellulose Fillers
PublicationThis study aimed to analyze the impact of cellulose fillers’ modification with diisocyanates on the performance of composites based on the poly(ε-caprolactone) (PCL) matrix. Four most commonly used diisocyantes (isophorone, hexamethylene, toluene, and methylene diphenyl) were applied as modifiers of cellulose fillers (5 and 15 wt% per mass of filler). Modified fillers were introduced in the amount of 30 wt% into the PCL matrix....
-
Weldability of Underwater Wet-Welded HSLA Steel: Effects of Electrode Hydrophobic Coatings
PublicationThe paper presents the effects of waterproof coatings use to cover electrodes on the weldability of high-strength, low-alloy (HSLA) steel in water. With the aim of improving the weldability of S460N HSLA steel in water, modifications of welding filler material were chosen. The surfaces of electrodes were covered by different hydrophobic substances. The aim of the controlled thermal severity (CTS) test was to check the influence...
-
An approach to evaluation of arguments in trust cases
PublicationTrustworthiness of IT systems can be justified using the concept of a trust case. A trust case is an argument structure which encompasses justification and evidence supporting claimed properties of a system. It represents explicitly an expert's way of assessing that a certain object has certain properties. Trust cases can be developed collaboratively on the basis of evidence and justification of varying quality. They can be complex...
-
Areas of Updraft Air Motion in an Idealised Weather Research and Forecasting Model Simulation of Atmospheric Boundary Layer Response to Different Floe Size Distributions
PublicationPresented dataset is part of a numerical modelling study focusing on the analysis of the influence of sea ice floe size distribution (FSD) on the horizontal and vertical structure of convection in the atmosphere. The total area and spatial arrangement of the up-drafts indicates that the FSD affects the total moisture content and the values of area averaged turbulent fluxes in the model domain. In fact, while convective updrafts...
-
Application of fracture mechanics for energetic effects predictions while wood sawing
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Cutting forces may be employed to determine not only toughness...
-
Degradation of polycaprolactone modified with TPS or CaCO3 in biotic/abiotic seawater
PublicationThis paper is an investigation of the polymer degradation process in two types of seawater (with and without microorganisms) sourced from the Baltic Sea. The chosen polymeric materials were polycaprolactone modified with either thermoplastic starch (PCL/TPS>85%) or calcium carbonate (60% PCL/40% CaCO3) compared directly against unmodified polycaprolactone. All samples were incubated for 28 weeks in seawater with and without microorganisms...
-
Morphology and mechanical properties of polyamide/clay nanocomposites toughened with NBR/NBR-g-GMA: A comparative study
PublicationThis work highlights the importance of nanoclay dispersion state in the nanocomposites containing polyamide 6 (PA6), nanoclay and elastomers as well as clay localization at the interface of thermoplastic/elastomer. Morphology and mechanical properties of a series of nanocomposites containing acrylonitrile butadiene rubber (NBR), glycidyl methacrylate-grafted NBR (NBR-g-GMA), and combined NBR/NBR-g-GMA were compared and discussed...
-
ReFlexeNN - the Wearable EMG Interface with Neural Network Based Gesture Classification
PublicationThe electromyographic activity of muscles was measured using a wireless biofeedback device. The aim of the study was to examine the possibility of creating an automatic muscle tension classifier. Several measurement series were conducted and the participant performed simple physical exercises - forcing the muscle to increase its activity accordingly to the selected scale. A small wireless device was attached to the electrodes placed...
-
RSS-Based DoA Estimation Using ESPAR Antenna Radiation Patterns Spline Interpolation
PublicationIn this paper, it is shown how power pattern crosscorrelation (PPCC) algorithm, which relies on received signal strength (RSS) values recorded at electronically steerable parasitic array radiator (ESPAR) antenna output port, used for direction-of-arrival (DoA) estimation, can easily be improved by applying spline interpolation to radiation patterns recorded in the calibration phase of the DoA estimation process. The proposed method...
-
A novel calibration method for RSS-based DoA estimation using ESPAR antennas
PublicationIn this paper, we introduce a new calibration method that can successfully be used in direction of arrival (DoA) estimation using electronically steerable parasitic array radiator (ESPAR) antennas and employing power-pattern cross-correlation (PPCC) algorithm, which relies on received signal strength (RSS) values recorded at the antenna output port. Instead of the commonly used two-step approach, during which ESPAR antenna calibration...
-
Influence of compaction effectiveness on interlayer bonding of asphalt layers
PublicationThe paper presents the results of research on the interlayer bonding of asphalt layers compacted in the laboratory and in the field. To measure the interlayer bonding at a temperature of 20°C the Leutner test apparatus was used and load was applied at a rate of 50 mm/minute. Three types of interlayer interfaces were tested: no tack coat and tack coats made of two types of the pure bitumen emulsions. Four compaction techniques were...
-
STABILITY ANALYSIS OF A TRUSS WITH SLOPING ELASTIC BRACES
PublicationSteel trusses have a much greater strength and stiffness in their plane than out of their plane, and therefore should be braced against lateral deflection and twisting. Such elements like purlins apart from bearing vertical load are part of bracing that stabilize roof trusses against distortional buckling. The stability of trusses with elastic bracing was investigated in an experimental research. Braces situated at some angle measured...
-
The Influence of Modelling Material Zones on Strains and Stresses at Weld Toe Notch
PublicationThe latest development in the field of welding technology enabled prefabrication of thin-walled sandwich structures in an industrial scale. Sandwich structures fabricated of steel, or aluminium alloy plates and stiffeners are welded with the use of hi-power CO2 lasers. Strength analysis of such structures with the use of finite element method needs proper material modelling.In this paper the material model of steel sandwich panel...
-
RSS-based DoA Estimation Using ESPAR Antennas and Interpolated Radiation Patterns
PublicationIn this letter, it is shown how an algorithm, which employs received signal strength (RSS) values in order to estimate direction-of-arrival (DoA) of impinging signals in wireless sensor network (WSN) nodes equipped with electronically steerable parasitic array radiator (ESPAR) antennas, can easily be improved by applying an interpolation algorithm to radiation patterns recorded in the calibration phase of the DoA estimation process....
-
Simple 2-D Direction-of-Arrival Estimation Using an ESPAR Antenna
PublicationIn this letter, it has been shown how an electronically steerable parasitic array radiator (ESPAR) antenna can be used for 2-D direction-of-arrival (DoA) estimation employing received signal strength (RSS) values only. The proposed approach relies on changes in RSS values recorded at the antenna output port observed for different vertical and horizontal directions, while antenna’s main beam sweeps 360° area around the ESPAR antenna. Based...
-
Estimation of fracture toughness and shear yield stress of orthotropic materials in cutting with rotating tools
PublicationThe cutting force is an energetic effect of splitting material, and might be considered from a point of view of modern fracture mechanics. Forecasting of the shear plane angle in cutting broaden possibilities for modelling of the cutting process even for thin uncut chips. Such mathematical model has been developed here for description of the orthotropic materials’ cutting on the base of fracture theory, and includes work of separation...
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublicationOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Superconductivity in the intermetallic compound Zr5Al4
PublicationPolycrystalline Zr5Al4 was synthesized using the arc-melting method. Powder X-ray diffraction confirms the previously reported crystal structure of the Ti5Ga4-type P63/mcm with lattice parameters: a = 8.4312(6) A , and c = 5.7752(8) A . Electrical resistivity and low-temperature magnetic susceptibility measurements indicate that Zr5Al4 exhibits superconducting behavior below 2 K. The normalized heat capacity jump at Tc= 1.82 K...
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublicationHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
Textile reinforced concrete members subjected to tension, bending, and in-plane loads: Experimental study and numerical analyses
PublicationTextile reinforced concrete has raised increasing research interest during the last years, mainly due to its potential to be used for freeform shell structures involving complex load situations. Yet, most experimental work has focused on test setups with primarily uniaxial loading. In the current work, such setups are complemented with a novel test setup of deep beams, including in-plane bending and shear. Further, nonlinear finite...
-
Influence of friction stir welding technological parameters on the properties of the joints of selected aluminum alloys
PublicationThe purpose of this dissertation was to determine the effect of friction stir welding technological parameters on the properties of selected aluminum alloy joints, with consideration of the residual stresses and dislocation density in the joints. The goal of the present work was also to produce defect-free joints with high mechanical and electrochemical properties. In the dissertation, similar welds of AA6082 alloy and dissimilar...
-
Effects of rapid heating on non-equilibrium microstructure evolution and strengthening mechanisms of titanium alloy
Publication -
Parametric analysis of Istanbul's Ring Road viaduct for three levels of seismic load
PublicationThe paper presents a parametric analysis of the Istanbul's ring road viaduct that is currently under construction within the Northern Marmara Highway project. The structure, due to its location on seismic prone areas is exposed to seismic loads of different strengths and different return periods. The study is focused on concrete bridge supports that are design to work in nonlinear range. The parametric study, conducted in MATLAB...
-
The magnetic field measurements in selected places of the industrial building
Open Research DataThe dataset is part of a comprehensive study on the assessment of the electromagnetic field intensity in a building of an operating industrial plant. Detailed results of magnetic field measurements, carried out in selected places of this building, are presented.
-
Electric field maps of an astable multivibrator in frequency range from 30 MHz to 3 GHz
Open Research DataThe data presents a result of near field measurements of electromagnetic emissions radiated from the PCB of a small electronic device. An efficient method of modelling the magnetic and electric field emissions is the measurements in the near field using electric and magnetic probes. The attached files contain electric field maps created on based measurements...
-
Impact of laser beam welding on mechanical behaviour of 2.25Cr–1Mo (P22) steel
PublicationThe use of welding processes in the manufacturing and repair of structures intended for the energy industry plays a key role in the guarantee of a continuous supply of fossil fuels, which is the basic condition for ensuring energy security. A square butt joint of 10 mm thick plate of 2.25Cr–1Mo (P22) steel was fabricated by autogenous laser beam welding process and then post-weld heat treatment (PWHT) for two sets of process parameters...
-
Improving Thermal Insulation Properties for Prefabricated Wall Components Made of Lightweight Aggregate Concrete with Open Structure
PublicationPorous concrete is commonly used in civil engineering due to its good thermal insulation properties in comparison with normal concrete and high compression strength in comparison with other building materials. An extremely porous concrete, called ‘lightweight aggregate concrete with open structure’ (LAC), is used in some German plants to produce prefabricated wall components. They are used mainly in hall buildings, e.g. supermarkets....
-
The concept of experience marketing - examples of practical application (PG_0005962), W, International Design Engineer, sem. 2, zimowy 2023/24
e-Learning CoursesCelem przedmiotu jest zaznajomienie studentów z koncepcją marketingu doświadczeń, będącego coraz częściej obligatoryjną podstawą innowacyjnych strategii marketingowych przedsiębiorstw oraz ukazanie praktycznego zastosowania niniejszej idei (zarządzanie doświadczeniami, strategiczne moduły doświadczeń, mapowanie podróży klienta i pracownika firmy). The aim of the course is to familiarize students with the concept of experience...
-
A review of design approaches for the implementation of low-frequency noise measurement systems
PublicationElectronic noise has its roots in the fundamental physical interactions between matter and charged particles, carrying information about the phenomena that occur at the microscopic level. Therefore, Low-Frequency Noise Measurements (LFNM) are a well-established technique for the characterization of electron devices and materials and, compared to other techniques, they offer the advantage of being non-destructive and of providing...
-
High-density Polyethylene - Expanded Perlite Composites: Structural Oriented Analysis of Mechanical and Thermomechanical Properties
PublicationAs part of this work, research was carried out on the effect of the addition of expanded perlite (PR) on the mechanical and thermomechanical properties of high-density polyethylene (PE) composites. Composites containing from 1 to 10 wt% of the inorganic filler were produced. Polyethylene-based composites manufactured by twin-screw extrusion and formed in the compression molding process were subjected to mechanical, thermomechanical,...
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublicationIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
Wireless Body Area Network for Preventing Self-Inoculation Transmission of Respiratory Viral Diseases
PublicationThis paper proposes an idea of Wireless Body Area Networks (WBANs) based on Bluetooth Low-Energy (BLE) standards to recognize and alarm a gesture of touching the face, and in effect, to prevent self-inoculation of respiratory viral diseases, such as COVID-19 or influenza A, B, or C. The proposed network comprises wireless modules placed in bracelets and a necklace. It relies on the received signal strength indicator (RSSI) measurements...