Filters
total: 1109
displaying 1000 best results Help
Search results for: REQUIRMENTS SPECIFICATION
-
Test loading of the longest span arch bridge in Poland
PublicationBridge structures undergo thorough examination during test loading before they come into use. The aim of the examination is to check the correctness of the working structure and construction design assumptions. Test loading on the bridge is preceded by examination specification. This paper describes computational model and test loading results carried out during examibation of the bridge over the Vistula within the bypass of Puławy...
-
Two-dimensional gas chromatography – principles and application in fruits analysis
PublicationTwo-dimensional gas chromatography is a rapidly developing analytical technique. One of the major uses of this technique is its use for food analysis. The paper presents the principle of operation and history of this analytical technique. The specification of the two-dimensional gas chromatography technique has been discussed. The principles of separation of ingredients and application of the method, particularly in the analysis...
-
Dynamic fracture of brittle shells in a space-time adaptive isogeometric phase field framework
PublicationPhase field models for fracture prediction gained popularity as the formulation does not require the specification of ad-hoc criteria and no discontinuities are inserted in the body. This work focuses on dynamic crack evolution of brittle shell structures considering large deformations. The energy contributions from in-plane and out-of-plane deformations are separately split into tensile and compressive components and the resulting...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Sterowanie optyczną siecią wielodomenową z hierarchiczną strukturą płaszczyzn sterowania
PublicationW artykule przedstawiono problem sterowania wielodomenową siecią optyczną z hierarchiczną strukturą płaszczyzn sterowania. Autorzy proponują wykorzystanie koncepcji sieci ASON/GMPLS, która spełnia wymagania nowoczesnych sieci optycznych, a jednocześnie umożliwia sterowanie wielodomenową siecią z gwarancją jakości usług. W artykule zaproponowano algorytm sterowania z gwarancją jakości, którego efektywność zweryfikowano metodą symulacji...
-
Toward Safe and Efficient Recovery of Gas Munitions Dumped at Sea
PublicationThe proposal of a system for the safe recovery of unexploded ordnance (UXO), chemical weapons (CW) and chemicalwarfare agents (CWA) dumped at sea mainly after WWI and WWII is described in this work. The proposed solutionaddresses the tasks required to neutralise thousands of tons of dumped material and the currently available solutionsand proposed ideas. Requirements concerning the features of a recovery system are defined and...
-
Test Design Patterns for Embedded Systems,
PublicationTest suites for embedded systems are typically created from scratch using dif- ferent, often inadequate methods. In consequence, industry branches dealing with software-intensive embedded systems have to cope with quality problems, even though test processes are particularly time-consuming and costly. Based on an evolving model-based testing methodology we introduce test design patterns for simplifying and accelerating...
-
Accurate simulation-driven modeling and design optimization of compact microwave structures
PublicationCost efficient design optimization of microwave structures requires availability of fast yet reliable replacement models so that multiple evaluations of the structure at hand can be executed in reasonable timeframe. Direct utilization of full-wave electromagnetic (EM) simulations is often prohibitive. On the other hand, accurate data-driven modeling normally requires a very large number of training points and it is virtually infeasible...
-
Load introduction to composite columns revisited—Significance of force allocation and shear connection stiffness
PublicationThe AISC 360-16 Specification recommends that the design shear force between parts of a composite column in the load introduction area shall be calculated based on the force allocation at ultimate limit state. Applicability of this straightforward method to the load levels that usually arise in slender composite columns is questionable, as this capacity-based force allocation is only true when the axial force is equal to the plastic...
-
Method of selecting programming practices for the safety-critical software development projects
PublicationIn recent years a plan-driven approach traditionally used in safety-critical software development has been put to a test by rapidly changing technologies, more diverse group of clients and volatile market requirements. The need to deliver good quality systems, faster and at lower cost in comparison to competitors encouraged companies to look for more efficient solutions. Agile methodologies are known to successfully address these...
-
Small Antenna Design Using Surrogate-Based Optimization
PublicationIn this work, design of small antennas using efficient numerical optimization is investigated. We exploit variable-fidelity electromagnetic (EM) simulations and the adaptively adjusted design specifications (AADS) technique. Combination of these methods allows us to simultaneously adjust multiple geometry parameters of the antenna structure of interest in a computationally feasible manner, leading to substantial reduction of the...
-
Wpływ właściwości cieczy hydraulicznej na wartość skoków ciśnienia w komorach pomp tłoczkowych osiowych
PublicationPublikacja dotyczy badań skoków ciśnienia w komorach roboczych pomp tłoczkowych osiowych. Skupiono się w nim na wpływie właściwości cieczy hydraulicznej na wartość skoków ciśnienia. Przeanalizowano wpływ takich parametrów jak: -gęstość, -lepkość, -ściśliwość, -zapowietrzenie. Do określenia wpływu właściwości cieczy na skoki ciśnienia wykorzystano badania laboratoryjne i symulacje komputerowe.
-
Methods of Network Resource Provisioning for the Future Internet IIP Initiative
PublicationIn this paper, we present specification, design and implementation aspects of a network resource provisioning module introduced for the Polish Initiative of Future Internet called System IIP. In particular, we propose a set of novel LP optimization models of network resource provisioning designed to minimize the network resource consumption, either bandwidth or node’s computational power, as well as to maximize the residual capacity....
-
Retrieval of Heterogeneus Sevices in C2NIWA Repository
PublicationThe paper reviews the methods used for retrieval of information and services. The selected approaches presented in the review inspired us to build retrieval mechanisms in a system for searching the resources stored in the C2NIWA repository. We describe the architecture of the system, its functions and the surrounding subsystems to which it is related. For retrieval of C2NIWA sevices we propos three approaches based on: keyword...
-
Data from the survey on Gdańsk University of Technology graduates’ competencies assessment by entrepreneurs
Open Research DataThe dataset includes data from the survey on the Gdańsk University of Technology (GUT) graduates’ competencies assessment by entrepreneurs. The survey was conducted in 2017. The research sample included 102 respondents representing various firms from Pomeranian Voivodship. The study concerned i.a. assessment of GUT graduates' preparation for the requirements...
-
Production of certified reference materials - homogeneity and stability study based on the determination of total mercury and methylmercury
PublicationReference materials (RMs) play an important role in all elements of the quality assurance system of measurements. In this work, ``package'' 4 new CRMs (bottom sediment, herring tissue, cod tissue, cormorant tissue) were prepared and characterised to carry out the quality control in monitoring analysis of mercury and methylmercury in environmental samples. Materials - candidates were collected in Poland and south part of the Czech...
-
Adaptive filtering approach to dynamic weighing: a checkweigher case study
PublicationDynamic weighing, i.e., weighing of objects in motion, with out stopping them on the weighing platform, allows one to increase the rate of operation of automatic weighing systems used in industrial production processes without compromising their accuracy. The paper extends and compares two approaches to dynamic weighing, based on system identification and variable-bandwidth filtering, respectively. Experiments, carried on a conveyor...
-
A Clustering-Based Methodology for Selection of Fault Tolerance Techniques
PublicationDevelopment of dependable applications requires selection of appropriate fault tolerance techniques that balance efficiency in fault handling and resulting consequences, such as increased development cost or performance degradation. This paper describes an advisory system that recommends fault tolerance techniques considering specified development and runtime application attributes. In the selection process, we use the K-means...
-
Contextual Knowledge to Enhance Workplace Hazard Recognition and Interpretation in a Cognitive Vision Platform
PublicationThe combination of vision and sensor data together with the resulting necessity for formal representations builds a central component of an autonomous Cyber Physical System for detection and tracking of laborers in workplaces environments. This system must be adaptable and perceive the environment as automatically as possible, performing in a variety of plants and scenes without the necessity of recoding the application for each...
-
Wzrost gospodarczy a zapotrzebowanie na prace - teoria i rzeczywistość gospodarcza Polski w latach 1995-2014
PublicationW części teoretycznej artykułu w pierwszej kolejności przedstawiono makroekonomiczne podstawy zapotrzebowania na pracę w warunkach postępu technicznego oraz zmian kapitału rzeczowego. W następnej kolejności sformułowano założenia dla modelu opisującego zależności pomiędzy stopami wzrostu produktu krajowego i zatrudnienia. W części empirycznej artykułu rozważano wybrane wersje oszacowanego modelu opisujące gospodarkę Polski. Do...
-
Rapid Design Centering of Multi-Band Antennas Using Knowledge-Based Inverse Models and Response Features
PublicationAccounting for manufacturing tolerances as well as uncertainties concerning operating conditions and material parameters is one of the important yet often neglected aspects of antenna development. Appropriate quantification of uncertainties allows for estimating the fabrication yield but also to carry out robust design (e.g., yield maximization). For reliability reasons, statistical analysis should be executed at the accuracy level...
-
Polish experience with cold in-place recycling
PublicationDeep cold in-place recycling using cement and asphalt emulsion has been used for reconstruction of existing roads since the beginning of the 1990s. This paper describes the first Polish requirements for mineral-cement-emulsion mixtures. As requirements stated for the strength of the mineral-cement-emulsion mixtures were quite high, most of the mixtures were designed using high amount of cement and aggregate added for the improvement...
-
The Principles of Model Building Concepts Which Are Applied to the Design Patterns for Smart Cities
PublicationThe involvement of citizens into decision-making processes is one of the main features of smart cities. Such commitment is reflected in the form of requirements towards the city, and the benefits which are expected from the city. Requirements and benefits are thus the primary language of communication between decision-makers and urban residents. To develop such a language, it becomes necessary to develop design patterns for Smart...
-
Voltage and frequency regulation of a standalone induction generator by reduced-rating power electronic compensators - comparative evaluation
PublicationIn this paper are considered two fundamental topologies of power electronic compensators for voltage and frequency control of a standalone self-excited induction generator (IG) system. These are voltage and current source inverter based shunt compensators with energy storage. The aim of this study is to assess main features of both topologies in dynamic and steady-state IG operation. The whole system is modelled with the aid of...
-
Szacowanie niepewności funkcji przetwarzania przetwornika LEM CT -5T metodą Monte Carlo
PublicationW referacie zaprezentowano metodologię szacowania niepewności funkcji przetwarzania przetwornika prądowego, na przykładzie przetwornika LEM CT-5T, przy zastosowaniu metody opartej na Przewodniku GUM z zastosowaniem prawa propagacji niepewności oraz metody numerycznej Monte Carlo. Przedstawiono szczegółową analizę doboru rozkładu wielkości wejściowej. W przypadku metody Monte Carlo dobór rozkładu wielkości wejściowych jest bardzo...
-
Szacowanie niepewności funkcji przetwarzania przetwornika LEM CT -5T metodą Monte Carlo
PublicationW referacie zaprezentowano metodologię szacowania niepewności funkcji przetwarzania przetwornika prądowego, na przykładzie przetwornika LEM CT-5T, przy zastosowaniu metody opartej na Przewodniku GUM, z zastosowaniem prawa propagacji niepewności oraz metody numerycznej Monte Carlo. Przedstawiono szczegółową analizę doboru rozkładu wielkości wejściowej. W przypadku metody Monte Carlo dobór rozkładu wielkości wejściowych jest bardzo...
-
Measurements of radiation emission of a portable power bank with a capacity of 10400 mAh
Open Research DataThe dataset contains the emission measurement results that are part of comprehensive tests carried out for portable power banks with different capacities. The measurements were performed in the frequency range from 30 MHz to 3 GHz using a Gigahertz Transverse Electromagnetic (GTEM) cell (Fig. 1). The test setup was configured to measure a portable power...
-
The scanning electron microscopy (SEM) studies of low voltage copper cables
Open Research DataThe dataset contains the scanning electron microscopy (SEM) images of the low voltage copper cables, which were studied in the article discussing the regulatory requirements for checking the electrical resistance of such cables. The cables were cut and studies in cross-section. The full results were published in:
-
Number of statements issued regarding the intention to entrust the performance of work in 2008-2018, broken down by country of origin of migrants
Open Research DataThe declaration of the intention to entrust work (applicable in the years 2007-2017) and the declaration of entrustment of work (applicable since 2018) are instruments for legalizing the work of foreigners in Poland, which by the ease of meeting the procedural requirements are by far the most popular among economic migrants and their employers.
-
Optimal Placement of Phasor Measurement Unit in Power System using Meta-Heuristic Algorithms
PublicationThe phasor measurement units (PMUs) play an important and vital role in power system monitoring and controlling, since they provide the power system phasors stamped with a common real time reference through a global positioning system (GPS). Indeed, from economical point of view it is not possible to set PMUs in all system buses due to the high cost and the requirement of more complex communication...
-
Rospuda - czy wszędzie budować mosty?
PublicationStreszczenie - SummaryThe article presents the problem of planning transport system in the areas of high natural and landscape values. Bridges and roads crossing valuable areas undergo Environmental Impact Assessment (EIA) Procedure. This procedure in Poland is often treated only as formal requirement, not as an instrument helping to solve conflicts and to minimise negative environmental and landscape effects. The potential of...
-
METODA WIELOKRYTERIALNEJ OCENY PRZEBUDOWY UKŁADÓW TOROWYCH NA SZLAKACH
PublicationRozprawa doktorska dotyczy zagadnienia projektowania układów geometrycznych toru kolejowego w procesie modernizacji linii kolejowych. Scharakteryzowano główne cechy dotyczące tej tematyki w oparciu o literaturę polską i zagraniczną, w tym przepisy branżowe. Przedstawiono czynniki wpływające na projektowanie modernizacji linii kolejowych. Określono wartości dopuszczalne parametrów kinematycznych i geometrycznych. Specyfika omawianego...
-
Toolchain Modeling: Comprehensive Engineering Plans for Industry 4.0
PublicationThe fourth industrial revolution (Industry 4.0) elevates the complexity and autonomy of industrial systems and engineering environments to levels not seen before. The novel challenges involve not only the software running on the partaking autonomous devices, but also architectural considerations and the technological infrastructure around the entire engineering process. In this paper, complementing the trends in industrial systems...
-
Artificial intelligence and productivity: global evidence from AI patent and bibliometric data
PublicationIn this paper we analyse the relationship between technological innovation in the artificial intelligence (AI) domain and macroeconomic productivity. We embed recently released data on patents and publications related to AI in an augmented model of productivity growth, which we estimate for the OECD countries and compare to an extended sample including non-OECD countries. Our estimates provide evidence in favour of the modern productivity...
-
R&D of satellite pumps and motors with small geometrical displacement supplied with oil and non-flammable liquids
PublicationThe newest construction of satellite motors and self-suction satellite pumps with small geometrical displacement have been described in this article. The characteristics of volumetric and total efficiency of one satellite motor, selected from the series, supplied with oil have been presented. These characteristics have been compared with the orbital motors' characteristics. The remaining specifications of these motors were also...
-
Hazard Control in Industrial Environments: A Knowledge-Vision-Based Approach
PublicationThis paper proposes the integration of image processing techniques (such as image segmentation, feature extraction and selection) and a knowledge representation approach in a framework for the development of an automatic system able to identify, in real time, unsafe activities in industrial environments. In this framework, the visual information (feature extraction) acquired from video-camera images and other context based gathered...
-
Rengel Cane Sia Doctoral Candidate
PeopleI’m Rengel, born and raised in the Philippines. As an undergraduate I did kinetic modeling on Copper-catalyzed atom transfer radical addition (ATRA). Then I was inspired to do both theoretical and experimental studies, which led me to propose my master’s thesis on Synthesis, Computational, Electrochemical, and Photoconductivity Studies on Naphthalene and its derivatives. This led to a master’s degree in Chemistry in the Mindanao...
-
Complex modulus of Cement Bitumen Treated Material Mixture (28 days of curing at 20C)
Open Research DataDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with 3 combinations of binding agents: 2% cement, 6% emulsion (C2E6), 6% cement, 6% emulsion (C6E6), 6% cement, 2% emulsion (C6E2). Mixture was designed according to Polish requirements for the base course of pavement. Mixture contains...
-
Fast and reliable knowledge-based design closure of antennas by means of iterative prediction-correction scheme
PublicationA novel framework for expedited antenna optimization with an iterative prediction-correction scheme is proposed. The methodology is comprehensively validated using three real-world antenna structures: narrow-band, dual-band and wideband, optimized under various design scenarios. The keystone of the proposed approach is to reuse designs pre-optimized for various sets of performance specifications and to encode them into metamodels...
-
Artificial intelligence and productivity: global evidence from AI patent and bibliometric data .
PublicationIn this paper we analyse the relationship between technological innovation in the artificial intelligence (AI) domain and macroeconomic productivity. We embed recently released data on patents and publications related to AI in an augmented model of productivity growth, which we estimate for the OECD countries and compare to an extended sample including non-OECD countries. Our estimates provide evidence in favour of the modern...
-
Extended Reflexive Ontologies for the Generation of Clinical Recommendations
PublicationDecision recommendations are a set of alternative options for clinical decisions (e.g., diagnosis, prognosis, treatment selection, follow-up, and prevention) that are provided to decision makers by knowledge-based Clinical Decision Support Systems (k-CDSS) as aids. We propose to follow a ‘‘reasoning over domain’’ approach for the generation of decision recommendations by gathering and inferring conclusions from production rules....
-
A Taxonomy of Model-Based Testing for Embedded Systems from Multiple Industry Domains
PublicationThis chapter provides a taxonomy of Model-Based Testing (MBT) based on the approaches that are presented throughout this book as well as in the related literature. The techniques for testing are categorized using a number of dimensions to familiarize the reader with the terminology used throughout the chapters that follow. In this chapter, after a brief introduction, a general definition of MBT and related work on available MBT...
-
IDENTIFICATION OF THE INTERFECE OF LATERAL SLIDE BEARINGS
PublicationIn the paper, the model of slide bearings of motor engine, the metodology of research on this type of bearings and its results are presented measurement standpoint consisting of main elements of Briggs & Stratton 550 serie 10 T 802 model piston motor engine driven by three phase elektric engine is introduced . On the measurement standpoint are measurements were done, needed for specification...
-
Modelling of the Heat Flux Density Distribution for Laser Beam Welding
PublicationGreat interest of the laser beam welding in industry is a new theoretical task, making planning the welding procedure specification and the quality control of welded joints easier. Estimating and calculating the dimensions of a weld pool and temperature distribution near weld mainly concern heat source modelling. In the presented work calculations of welding pool shape and thermal field for cylindrical-powered-normally model of...
-
Deflated Preconditioned Solvers for Parametrized Local Model Order Reduction
PublicationOne of steps in the design of microwave filters is numerical tuning using full-wave simulators. Typically, it is a time-consuming process as it uses advanced computational methods, e.g. the finite-element method (FEM) and it usually requires multiple optimization steps before the specification goals are met. FEM involves solving a large sparse system of equations at many frequency points and therefore its computational cost is...
-
Software-Defined NB-IoT Uplink Framework - The Design, Implementation and Use Cases
PublicationIn the radiocommunication area, we may observe a rapid growth of new technology, such as 5G. Moreover, all the newly introduced radio interfaces, e.g., narrowband Internet of Things (NB-IoT), are strongly dependent on the software. Hence, the radiocommunication software development and optimization, as well as the 3GPP technical specification, should be introduced at the academic level of education. In this paper, a software-defined...
-
Production and Properties of the Porous Layer Obtained by the Electrochemical Method on the Surface of Austenitic Steel
Publication: The growing demand for implants has seen increasing interest in the introduction of new technologies and surface modification methods of metal biomaterials. This research aimed to produce and characterize a porous layer grown on austenitic stainless steel 316L, obtained via the anodization process near the micro-arc oxidation, i.e., low voltage micro-arc oxidation (LVMAO). The discussed layer significantly influences the properties...
-
Complex modulus of Cement Bitumen Treated Material Mixture C3E4 laboratory mixed/laboratory compacted (7-365 days of curing at 20C)
Open Research DataDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement, 4% emulsion (C3E4). Mixture was designed according to Polish requirements for the base course of pavement. Mixture was mixed in laboratory conditions on the basis of materials obtained from...
-
Complex modulus of Cement Bitumen Treated Material Mixture C3E4 field mixed/laboratory compacted (7-365 days of curing at 20C)
Open Research DataDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement, 4% emulsion (C3E4). Mixture was designed according to Polish requirements for the base course of pavement. Mixture was mixed in the field conditions and later compacted in laboratory. Mixture...
-
Deformation Sweep Test of Cement Bitumen Treated Material Mixture C3E5.5 (field obtained material; over 28 days of curing at 20C)
Open Research DataDataset presents data of results of deformation sweep test determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement and 5.5% emulsion (C3E5.5). Mixture was designed according to Polish requirements for the base course of pavement. Mixture contains 60% of RAP material. Specimen size: f=100...