Search results for: VULNERABILITY TO FLOODING
-
Dynamic analysis of lightweight structure of the Viaduct Millau in France subjected to the wind fluctuations described by Karman’s and Davenport’s spectrum
PublicationThe article presents numerical simulations for wind impact modelling on the Millau Viaduct structure in France performed with two independent spectrum generation methods. The viaduct's construction in affected by strong forces, as it is situated in the Tarn river's valley. Thus, the loading coming from the wind cannot be modelled, the way it is in case of simple structures as static loading, but as a loading in a form of a spectrum...
-
Fatigue fracture surface metrology of thin-walled tubular austenitic steel specimens after asynchronous loadings
PublicationThis paper aims to study the effect of asynchronous axial-torsional strain-controlled loading histories on fracture surface behavior of thin-walled tubular X5CrNi18-10 (304/304L) austenitic steel specimens. Tests under pure axial loading and pure torsional loading are also conducted to better segregate the effect of multiaxiality. The fractures surface topographies were examined through the profiles over the entire surface with...
-
Fault Diagnostics in PEMFC Stacks by Evaluation of Local Performance and Cell Impedance Analysis
PublicationStarvation, flooding, and dry‐out phenomena occur in polymer electrolyte membrane fuel cells (PEMFCs), due to heterogeneous local conditions, material inhomogeneity, and uneven flow distribution across the single cell active area and in between the individual cells. The impact of the load level and air feed conditions on the performance was identified for individual single cells within a 10‐cell stack. Analysis of the current density...
-
Introduction to advanced numerical methods in engineering
e-Learning Courses -
Magnetism from fundamentals to spintronics 22/23
e-Learning Courses1. Basic magnetic quantities2. Magnetism of atoms and molecules, atoms in external magnetic fields3. Solid state magnetism, types of magnetic materials (dia-, para-, and ferromagnetism)4. Ferromagnetism and domain structures5. Magnetism of small particles, single domain particles (StonerWohlfarth model), thin films6. Experimental techniques of magnetic properties and magnetisation state determination. Domain structurevisualisation...
-
Zdolni z Pomorza 2017/18 - Wyrzuć to!
e-Learning CoursesCel kursu: Celem kursu jest zapoznanie uczniów z pojęciem rzutu oraz jego przykładami. Opis kursu: Co szybciej spadnie, kilogram pierza czy kilogram gwoździ? Jak daleko doleci kopnięta piłka? Między innymi na te pytania będziemy szukali odpowiedzi analizując kinematykę i dynamikę rzutów. W pierwszej części kursu zostaną przypomniane podstawowe zagadnienia związane z kinematyką ruchu jednostajnego i jednostajnie przyspieszonego....
-
How to learn better at Polish university?
e-Learning Courses -
Introduction to Ship Design O:114009 20232024
e-Learning Courses -
PLANNING AND ANALYSIS OF EARTHQUAKE DISASTER RELIEF WORK IN ETHIOPIA
PublicationThis paper addresses dynamic planning and analysis of earthquake disaster relief work by analysis the disaster throughout the technical and procedural method. And combine this analysis as continues assessment for better input to investigating planning disaster for discontinuous economic growth. This implemented, considering the vulnerability and hazard analysis as a procedural analysis disaster to estimating acceptance risk leveling...
-
Nanocrystalline diamond sheets as protective coatings for fiber-optic measurement head
PublicationFiber-optic sensors find numerous applications in science and industry, but their full potential is limited because of the risk of damaging the measurement head, in particular, due to the vulnerability of unprotected tips of the fiber to mechanical damage and aggressive chemical agents. In this paper, we report the first use of a new nanocrystalline diamond structure in a fiber-optic measurement head as a protective coating of...
-
Functional Safety and Cybersecurity Analysis and Management in Smart Manufacturing Systems
PublicationThis chapter addresses some of the issues of the integrated functional safety and cybersecurity analysis and management with regard to selected references and the functional safety standards: IEC 61508, IEC 61511, ISO 13849-1 and IEC 62061, and a cybersecurity standard IEC 62443 that concerns the industrial automation and control systems. The objective is to mitigate the vulnerability of industrial systems that include the information...
-
Mode shapes of a beam and plate with defects, obtained by experimental modal analysis
Open Research DataThe DataSet contains the experimental results of the first mode shape for a beam and a plate.
-
Assessing Highway Travel Time Reliability using Probe Vehicle Data
PublicationProbe vehicle data (also known as “floating car data”) can be used to analyze travel time reliability of an existing road corridor in order to determine where, when, and how often traffic congestion occurs at particular road segments. The aim of the study is to find the best reliability performance measures for assessing congestion frequency and severity based on probe data. Pilot surveys conducted on A2 motorway in Poland confirm...
-
AFM (atomic force microscopy) images of borophene flakes obtained during ball milling at different operating parameters
Open Research DataThis dataset contains atomic force microscopy (AFM) images of representative borophene flakes obtained during ball milling. The operational parameters of the ball-milling process included rotation speed (250, 450, and 650 rpm), time of ball-milling (1, 3, 6, and 12 h), and the mass loading of starting bulk boron (1, 2, 3 g).
-
Strain sequence effect on fatigue life and fracture surface topography of 7075-T651 aluminium alloy
PublicationThe paper studies the effect of strain-loading sequence on fatigue lifetime and fracture surface topographies in 7075-T651 aluminum alloy specimens. Fatigue tests were performed in two ways: (i) constant-amplitude loading and (ii) two series of variable amplitude loading with non-zero mean strain values. The topography of the fatigue fractures was measured over their entire surfaces with the help of an optical confocal measurement...
-
Numerical Analysis of Recharge Rates and Contaminant Travel Time in Layered Unsaturated Soils
PublicationThis study focused on the estimation of groundwater recharge rates and travel time of conservative contaminants between ground surface and aquifer. Numerical simulations of transient water flow and solute transport were performed using the SWAP computer program for 10 layered soil profiles, composed of materials ranging from gravel to clay. In particular, sensitivity of the results to the thickness and position of weakly permeable...
-
Wyzwania bezpieczeństwa nowoczesnych platform nauczania zdalnego
PublicationW artykule zaprezentowano aspekty bezpieczeństwa nowoczesnych platform nauczania zdalnego. Przedstawiono ich charakterystykę i wyzwania technologiczne. Zdefiniowano bezpieczeństwo i istniejące w tym obszarze zagrożenia. Przybliżono metody oceny poziomu bezpieczeństwa. Na bazie wdrożonej na Politechnice Gdańskiej platformy eNauczanie PG omówiono sposoby zapewniania zakładanego poziomu bezpieczeństwa takich systemów.
-
Agnieszka Potęga dr inż.
People -
Correlation between Fractal Dimension and Areal Surface Parameters for Fracture Analysis after Bending-Torsion Fatigue
PublicationThis paper investigates the fracture surface topography of two steel and aluminum alloys subject to bending-torsion fatigue loadings, as well as their susceptibility to fatigue performance and failure mechanisms. Using fracture surface topography data analysis, elements with different geometries were elaborated. A correlation between the fractal dimension, other selected parameters of surface topography such as areal Sx, and...
-
Measure small currents without adding resistive insertion loss
PublicationFloating current to voltage converter can be inserted in-line with no voltage drop and no need for a ground reference.
-
Effects of deviations from thermo-rheologically simple behavior of asphalt mixes in creep on developing of master curves of their stiffness modulus
PublicationThe paper presents the deviations from the thermo-rheologically simple behavior of asphalt mixes and their effects on the developing of master curves of stiffness modulus. Eleven different mixes were tested in three point bending test under constant load at temperatures –20°C, –10 °C and 0 °C, and in some cases at +10 °C. The test method was developed at the Gdansk University of Technology, Poland. The applied stress level was...
-
[AEiE] Introduction to advanced numerical methods in engineering
e-Learning Courses{mlang pl} Dyscyplina: automatyka, elektronika i elektrotechnika Zajęcia obowiązkowe dla doktorantów II roku Prowadzący: dr hab. inż. Robert Bogdanowicz, prof. PG, dr inż. Grzegorz Fotyga, dr hab. inż. Piotr Kowalczyk, prof. PG, dr hab. inż. Rafał Lech, prof. PG, dr hab. inż. Paweł Wierzba, prof. PG Liczba godzin: 15 Forma zajęć: wykład Kurs realizowany w zakładce WETI: https://enauczanie.pg.edu.pl/moodle/course/view.php?id=10126 Na...
-
Introduction to Sustainability and Sustainable Management - TOO4TO Project
e-Learning Courses -
Density functional approaches to the many-body problem
e-Learning Courses -
PKM I (lato 2023/2024) TO TEN kurs!
e-Learning Courses -
Nicole Nawrot dr inż.
PeopleDr. Eng. Nicole Nawrot has been employed at the Department of Sanitary Engineering since 2016. In 2021, she obtained a PhD in the field of engineering and technical sciences in the discipline of environmental engineering, mining and energy. Doctoral thesis entitled "Heavy metals in urban retention tanks bottom sediments: distribution, source tracking, and evaluation of phytostabilization adaptability and performance of P. australis...
-
Mobile Laser Scanning Calibration on a Marine Platform
PublicationThe article describes the method of calibration of the Riegl VMZ-400 mobile scanning system on a floating platform and an experiment aimed at conducting measurements from a previously calibrated instrument. The issue of factors affecting the quality of measurements was discussed. Mobile laser scanning is an increasingly popular measurement solution, but it is still innovative on a European scale. The use of a floating platform...
-
Estimation of Conservative Contaminant Travel Time through Vadose Zone Based on Transient and Steady Flow Approaches
PublicationEstimation of contaminant travel time through the vadose zone is needed for assessing groundwater vulnerability to pollution, planning monitoring and remediation activities or predicting the effect of land use change or climate change on groundwater quality. The travel time can be obtained from numerical simulations of transient flow and transport in the unsaturated soil profile, which typically require a large amount of data and...
-
Investigation of Continuous Wave Jamming in an IEEE 802.15.4 Network
PublicationThis paper presents how continuous wave jamming affects IEEE 802.15.4 network. To this end, an office-based measurement setup has been proposed. Within the measurement area, 25 nodes have been set up in order to create a IEEE 802.15.4 tree-based test network structure. A dedicated jamming device that generates and transmits a continuous wave signal has been developed. Several tests have been conducted and presented to demonstrate...
-
Greencoin information system empowering urban adaptability and eco living choices.
PublicationThere are many gamification projects focused on mitigating climate changes which has been tested or implemented worldwide. However, the gap which remains is the limited number of solutions dedicated for central European countries where the urban polices in terms of climate vulnerability are bounded. On the other hand, cities, when implementing climate-oriented policies, are focused on urban resilience, while the opportunities...
-
Device-independent quantum key distribution based on measurement inputs
PublicationWe provide an analysis of a family of device-independent quantum key distribution (QKD) protocols that has the following features. (a) The bits used for the secret key do not come from the results of the measurements on an entangled state but from the choices of settings. (b) Instead of a single security parameter (a violation of some Bell inequality) a set of them is used to estimate the level of trust in the secrecy of the key....
-
How pesticides affect neonates? - Exposure, health implications and determination of metabolites
PublicationThis review covers key information related to the effects of pesticides on fetal and child health. All humans are exposed to environmental toxicants, however child's health, due to their high vulnerability, should be of special concern. They are continuously exposed to environmental xenobiotics including a wide variety of pesticides, and other pollutants. These compounds can enter the child's body through various routes, both during...
-
Resource constrained neural network training
PublicationModern applications of neural-network-based AI solutions tend to move from datacenter backends to low-power edge devices. Environmental, computational, and power constraints are inevitable consequences of such a shift. Limiting the bit count of neural network parameters proved to be a valid technique for speeding up and increasing efficiency of the inference process. Hence, it is understandable that a similar approach is gaining...
-
Application of different building representation techniques in HEC-RAS 2-D for urban flood modeling using the Toce River experimental case
PublicationThis paper presents the impact of the choice of building representation techniques and hydrodynamic models on urban flood simulations using HEC-RAS 2-D for the Toce River physical model. To this end, eight numerical models based on previous laboratory experiments were prepared to simulate unsteady urban flooding on each side of building units. Two simplified building layouts (aligned and staggered) were examined, where models were...
-
Chemical and Mechanical Properties of 70-Year-Old Concrete
PublicationThe aim of this research is to determine the durability and strength of concrete continuous footing based on the chosen mechanical, physical, and chemical properties of the concrete. The presented investigations constitute some opinions from experts on the bearing capacity of concrete continuous footing and the possibilities of carrying additional loads and extended working life. The cylindrical specimens were taken from continuous...
-
Technical fabrics in costruction of large scale roofs - numerical and experimental aspects
PublicationDesigning and construction of textile hanging roofs is the challenging subject for engineers. This type of structure needs geometrically and very often also physically non-linear calculations. Due to different behaviour of two families of threads (warp and weft), which during deformation can change the angle between their directions, they require special constitutive modelling. Also the loading of hanging roofs is very special....
-
Aravind Ayyolath
PeopleI am interested in the biology of bacterial stress response and its growth under stress conditions. Our lab focuses on two aspects; protein folding and lipopolysaccharide biosynthesis and we address them with Escherichia coli models. Our recent studies have provided more evidence regarding several genes involved in the survival of bacteria under stress. I am also interested in disease biology and also in identifying proper therapeutic...
-
Investigation on water infiltration and water content changes in a large-scale experimental test dike
PublicationThe paper presents result of series of experiments made within the DREDGDIKES project, performed on a test dike built from composite soil. The composite is produced by mixing fly ash (by-product of energetics) with dredged material (sand) taken from the mouth of The Vistula river. The test dike, located near Gdansk in Poland, was subjected to hydraulic load in several flooding time scenarios and the unsaturated unsteady flow was...
-
Behaviour of steel columns under impact
PublicationOne of import issues related to the idea of sustainable society is the safety of civil engineering structures. The safety and reliability of steel structures under impact loading is among a number of different aims during the design state. The aim of this paper is to present the results of investigation focused on dynamic behaviour of steel columns under impact loading. Modal and transient dynamic analyses using Finite Element...
-
Low frequency nois of supecapacitor
Open Research DataDataset contains noise measurement results on prototype electrochemical double layer capacitor. The measurement procedure is described in https://dx.doi.org/10.1515/mms-2017-0059.
-
Structural reliability of overhead power lines by means of Monte Carlo Method and RSM
PublicationThe article discusses the issue of reliability assessment of overhead power lines by means of both Monte Carlo Method and Response Surface Method. The suspension tower OS24 ON150+10 is considered, as the weakest element of the line. A comparison is made between deterministic and probabilistic approaches to wind and icing loading. The PDFs for wind and icing loads are proposed. Reliability is assessed for both critical atmospheric...
-
Raz jeszcze o obciążeniu hydrodynamicznym falochronu pionowościennego falą stojącą
PublicationPrzedstawienie istniejących modeli matematycznych opisujących rozkłady ciśnienia hydrodynamicznego na falochron pionowościenny w wyniku oddziaływania fali stojącej. Analiza nieciągłości ciśnienia. Jakościowe porównanie metod obliczeniowych dla wybranych warunków wodno-falowych.
-
Blanka Tundys dr hab.
PeopleBlanka Tundys is an Associate Professor at University of Szczecin, Poland. Her research interests span green supply chain, sustainable supply chain, close loop chain, eco-innovation, city logistics, logistics, transport systems, city economics, strategy in logistics, transportation, performance measurement in logistics and supply chain, efficiency in logistics, circular economy, smart city, risk management in the supply chain,...
-
FTIR in situ - ethylene decomposition on TiO2
Open Research DataThese data contain FTIR spectra recorded in FTIR spectrometer Nicolet iS50 coupled with High Temperature Chamber "The Praying Mantis". These spectra were measured for TiO2 irradiated by UV and under flowing of ethylene gas diluted in air. FTIR spectra were measured in situ during the photocatalytic process of ethylene decomposition. In order to identify...
-
Personalized nutrition in ageing society: redox control of major-age related diseases through the NutRedOx Network (COST Action CA16112)
PublicationA healthy ageing process is important when it is considered that one-third of the population of Europe is already over 50 years old, although there are regional variations. This proportion is likely to increase in the future, and maintenance of vitality at an older age is not only an important measure of the quality of life but also key to participation and productivity. So, the binomial “nutrition and ageing” has different aspects...
-
Fractal dimension for bending–torsion fatigue fracture characterisation
PublicationFracture surfaces after biaxial fatigue tests were compared using fractal dimension for three types of metallic materials in smooth and notched specimens made of S355J2 and 10HNAP steels and 2017-T4 aluminium alloy, considering both proportional and nonproportional cyclic loading. High-resolution optical 3D measurement studies were performed on the entire fracture surface. A direct correlation between fractal dimension and fatigue...
-
Fractographic-fractal dimension correlation with crack initiation and fatigue life for notched aluminium alloys under bending load
PublicationIn this study, fatigue fracture surfaces of aluminium alloy 2017-T4 notched specimens were investigated under cyclic bending to find an alternative failure loading index.. The surface topographies were measured on the entire fracture area with an optical profilometer for different loading conditions. Fatigue crack initiation life Ni and total fatigue life Nf were examined using standard surface topography parameters (such as, root...
-
Effect of geometric imperfections on aluminium silo capacities
PublicationAn aluminum silo with initial imperfections is analysed. Two types of imperfections are considered. The first one takes the form of local indentations in the shell; their size and range are adopted on the basis of the standard guidelines. The second type is a global imperfection described through the use of its eigenforms and by means of two-dimensional random fields. The calculations are limited to two cases of loading: negative...
-
Spatiotemporal dynamics of the active perirheic zone in a natural wetland floodplain
PublicationAbstract The ecologically and biogeochemically significant perirheic zone is a part of the floodplain where waters originating from both the river and adjacent floodplain are present. In this study, we investigate the spatiotemporal dynamics of the active perirheic zone, i.e. river and floodplain waters and their transient mixing extent. This is achieved by using the Hydraulic Mixing-Cell method, a complement to a fully integrated...
-
Mathematical Modeling of Ice Dynamics as a Decision Support Tool in River Engineering
PublicationThe prediction of winter flooding is a complicated task since it is affected by many meteorological and hydraulic factors. Typically, information on river ice conditions is based on historical observations, which are usually incomplete. Recently, data have been supplemented by information extracted from satellite images. All the above mentioned factors provide a good background of the characteristics of ice processes, but are not...