Filters
total: 1025
displaying 1000 best results Help
Search results for: cable bentonite
-
The effect of cable duct diameter on the ampacity of high-voltage power cables
PublicationThe ampacity of power cables depends, among others, on the conditions of heat dissipation from the cable to the environment. Cables are usually laid directly in the ground, but in some sections, they may be placed in ducts, which adversely affects the ampacity of the cable line. The paper presents heat transfer phenomena for cables installed in pipe-type ducts filled with air. The effect of cable duct diameter on this ampacity...
-
Application of Structural Control Systems for the Cables of Cable-Stayed Bridges: State-of-the-Art and State-of-the-Practice
PublicationStay cables are one of the key elements of cable-stayed bridges and are characterized by lightweight, low inherent damping, and high flexibility. They are continuously subjected to small-to large-amplitude vibrations due to various types of dynamic loads that may, in the long term, cause fatigue and fracture problems for the cable system, and may eventually compromise the safety of cable-stayed bridges. Thus, several countermeasures...
-
The investigation of polyester composites filled by modified bentonite
PublicationPraca dotyczy zagospodarowania odpadów poliestrowo-szklanych przez wytworzenie kompozytów z ich użyciem oraz żywicy poliestrowej, mączki dolomitowej i nanonapełniacza. Wykazano, ze dodatek 2% nanonapełniacza do do kompozytów poliestrowych zawierających 15% masowych odpadów pozwala na uzyskanie materiału wykazującego korzystne właściwości wytrzymałościowe. Proponowany sposób modyfikacji kompozytów poliestrowych jest nowym rozwiązaniem...
-
Influence of salinity on the consistency and swelling characteristics of bentonite
PublicationRaport z badań eksperymentalnych odnośnie konsystencji bentonitu (wskaźniki plastyczności, stopień plastyczności) i zjawiska pęcznienia (ciśnienie pęcznienia) przedstawiono w zależności od różnych poziomów zasolenia wody.
-
Round Table
Journals -
Numerical crash analysis of the cable barrier
PublicationSafety barriers are used to increase road safety. Their basic task is to prevent the errant vehicle from getting off the road in places which are potentially dangerous for vehicle passengers. Barriers, which are used on European roads, must fulfill the requirements of EN 1317 standards by passing appropriate crash tests. Because of their high cost, numerical simulations are increasingly used to evaluate the properties of safety...
-
Modelling of MV and HV Cable Lines
PublicationOverhead and cable lines are fundamental elements of power systems. Participation of cable lines is smaller and their percentage decreases as voltage is increased. HV cable lines are often built with the use of cables which are composed of coaxial metallic sheaths. Such cables are also often used in MV networks. The sheath may operate in different confgurations. In the case of Polish MV network the sheaths are earthed at both ends....
-
Conducting composites as cable anodes in cathodic protection
PublicationOpisano zasadę działania oraz podstawowe parametry charakteryzujące układ anodowy z wykorzystaniem anod kablowych w systemie ochrony katodowej podziemnych konstrukcji. W tej metodzie ochrony jako materiał anodowy wykorzystywany jest kompozyt przewodzący, którego właściwości mechaniczne umożliwiają budowę anody w formie kabla biegnącego wzdłuż trasy konstrukcji podziemnej. Wykazano, że zawartość grafitu w elektrodzie kompozytowej...
-
Cable-stayed bridges. Basic static schemes
PublicationThe paper presents an overview of shaping of cable-stayed bridges. Historical background, basic static sketches and overview of selected bridges are included. Selected natural solutions and interesting unrealized projects were presented. Basic ideas and most important principals are discussed. The examples and sketches were given an author's comment. Static diagrams of two pylon structures with three variants of the arrangement...
-
Dynamic Response of the Suspended on a Single Cable Footbridge
PublicationThe article presents numerical simulations, dynamic in situ load tests and a structural health monitoring (SHM) system installed in a suspended on a single cable footbridge. Numerical simulations performed prior to construction indicated the possibility of structural dynamics problems, finally confirmed in the course of dynamic test loading. In the dynamic load course the bridge deck developed vibrations displaying accelerations...
-
Wpływ zasolenia wody na konsystencję i pęcznienie bentonitu
PublicationBentonit ma szerokie zastosowanie w przemyśle budowlanym jako ochrona fundamentów i tuneli przed szkodliwym efektem niekorzystnego ruchu wody gruntowej. Geotechniczne zachowanie się bentonitu, a w szczególności aktywowanego granulatu, wynika przede wszystkim z oddziaływania wodą. Rozszerzając swoją objętość zmienia się w tiksotropowy żel, uniemożliwiając przepływ filtracyjny, jednocześnie wydłużając czas konsolidacji.
-
Wpływ bentonitu na właściwości samoprzylepne silikonowych klejów samoprzylepnych
Publication -
Introducing Bentonite into the Environment in the Construction Stage of Linear Underground Investment Using the HDD Method
Publication -
S-scheme heterojunction Bi2O3-ZnO/Bentonite clay composite with enhanced photocatalytic performance
PublicationThe industrial waste water is always a bottleneck problem in the modern civilization of the present era. In a quest to develop effective methods for the elimination of lethal pollutants from the waste water and water remediation, this work is focused on the development of a rapid and proficient approach for preparing supported binary metal oxide catalyst for photocatalytic advance oxidation process used in waste water treatment...
-
Micro‑ and nano‑ bentonite to improve the strength of clayey sand as a nano soil‑improvement technique
PublicationNano-additives results in the formation of nano-cementation (NC). This process is recently used to improve the durability of various building materials. NC used to improve the strength of untreated soil materials, also known as nano soil-improvement (NSI). In few years, the role of nano-additives in various types of soils were developed. In this research, the role of micro- and nano- size of bentonite as soil stabilizer was evaluated...
-
Heat Dissipation from the Power Cable in the Casing Pipe
PublicationThe current carrying capacity of a power cable determines its ability to carry a specific current and is related to the efficiency of dissipation of heat generated in the cable laid in a specific environment. The studies were conducted in order to determine how the characteristics of the medium around the cable affected its temperature, and thus the ability of the cable to transmit electricity. The experimentation in the lab and...
-
Shape and force control of cable structures with minimal actuators and actuation
Publication -
AC motor feeding cable consequences on EMC performance of ASD
PublicationHigh level of conducted EMI emissions of adjustable speed drives (ASD) is one of the most difficult problems in contemporary applications. Many investigations are carried out in order to find more effective methods allowing to predict this emission at early stage of design, and therefore to predict adequate countermeasures. This paper deals with the method which allows to estimate by simulation the influence of motor feeding cable...
-
Conducting composites as cable anodes in cathodic protection: a literature summary
PublicationPrzedstawiono podstawową charakterystykę systemu ochrony katodowej z wykorzystaniem anod kablowych. Anody kablowe różnią się od klasycznych systemów anodowych sposobem instalacji anod. System anodowy oparty na anodach kablowych nie jest instalowany punktowo; anoda umieszczana jest w niewielkiej odległości od chronionej konstrukcji i biegnie wzdłuż trasy konstrukcji. Materiałem anodowym proponowanego rozwiązania jest elastyczny...
-
A new approach to cross-bonding in medium voltage cable lines
PublicationThe medium voltage underground cable sheaths are usually bonded and earthed in every substation on the cable route. This results in additional power losses in the sheaths. The paper presents an idea of reducing power losses caused by sheaths cross-bonding. The idea of sheaths cross-connecting only in selected MV/LV substations is given instead of a typical solution, where sheaths cross-bonding requires installing additional joints...
-
Characterization of Defects Inside the Cable Dielectric With Partial Discharge Modeling
PublicationThe continuous monitoring of power system devices is an important step toward keeping such capital assets safe. Partial discharge (PD)-based measurement tools provide a reliable and accurate condition assessment of power system insulations. It is very common that voids or cavities exist in every solid dielectric insulation medium. In this article, different voids are modeled and analyzed using an advanced finite element (FE)-based...
-
Shape and force control of cable structures with minimal actuators and actuation
PublicationShape adjustment and stress control can be considered as one of the effective parameters in prestressed cable structures since such structures are widely constructed nowadays due to their characteristics. The assembly errors and applied loads hugely affect the cables’ nodal positions and stress due to their delicacy. The former could disturb the shape, which affects the appearance and the function of the structure. In contrast,...
-
Modeling and Evaluation of Electric Treeing Phenomena in Polymeric Cable Insulation
PublicationThis paper investigates the treeing phenomenon in polymeric materials such as crosslinked polyethylene (XLPE) that is widely used in medium and high voltage power cables as primary insulation. The modeling of electrical tree growth in the insulation from its initiation to breakdown is significant research work that illustrates the discharge dynamics and its impact on aging process in polymeric insulation. This study utilizes pulse...
-
Cross-Bonding of MV Cable Lines for Energy Losses Decrease
PublicationCurrently, almost all medium voltage cable lines (MV) operate with the return wires earthed at both ends of the cable. Such a way of operation causes that during normal states of operation as well as during disturbances, e.g. short-circuits, in the return wires induce currents whose values mainly depend on the currents flowing in the phase wires. These currents in normal operating states are a source of additional energy losses...
-
Reference FEM model for SHM system of cable-stayed bridge in Rzeszów
PublicationThe paper presents the references model for structural health monitoring system (SHM) of cable-stayed bridge recently constructed in Rzeszów over Wisłok River. The SHM system is design to provide on-line information on the structure state and facilitate its maintenance procedures. The main feature of the SHM system is permanent observation of the dynamic behavior of the bridge with focus on cable vibrations. The paper discusses...
-
Pylon foundation of a cable stayed bridge at the motorway ring road of Wrocław
PublicationThe largest bridge of the motorway ring road of Wroclaw is a cable stayed bridge over the Odra river near Rędzin. Due to hydrogeological conditions of the ground it was not convenient to use standard bored piles of high length. Instead shorter piles were applied with additional improvement by cement injections at the pile toes. This decision was possible by extending ground investigation program and application of numerical modeling...
-
The influence of position of the post or its absence on the performance of the cable barrier system
PublicationRoad safety barriers are used to increase safety in potentially dangerous places on the roads. They are designed and installed on the roads to prevent any vehicle from getting outside the travelled way or from entering the opposite lane of the road. Barriers, which are used on European roads, have to undergo full scale crash tests according to the EN 1317 standards. Nowadays as a supplement to real crash tests, numerical simulations...
-
Theoretical analysis of the cable-stayed bridge over brda river in Bydgoszcz
PublicationThe topic of this article is the numerical analysis carried out for the cable-stayed tram (road) bridge over Brda river in Bydgoszcz. The goal of numerical studies was the verification of project assumptions and construction solutions elaborated by the autonomous team. The bridge calculations were conducted on three independent FEM models The internal forces and the elements effort under different loading schemes were examined....
-
Adjustment for shape restoration and force control of cable arch stayed bridges
Publication -
Displacements of Cable-Stayed Bridge Measured With The Use of Traditional And Modern Techniques
Publication -
Broadband Modeling of Motor Cable Impact on Common Mode Currents in VFD
PublicationExamination of conducted EMI generation and propagation in AC motor drives fed by frequency converter requires to consider parasitic capacitances in converters, motor windings and feeding cables to be taken into account. AC motor winding voltage transients and related common mode currents are significantly correlated with resonance effects occurring in converter's load circuits. Intensity levels of these phenomena depend...
-
Determination of the Bending Properties of Wire Rope Used in Cable Barrier Systems
PublicationThis paper presents research on the bending properties of 3 × 7 19-mm wire rope commonly used in road cable barriers. A total of 19 experimental tests were conducted. In addition, two nonlinear 3D numerical models of the wire rope using beam and solid finite elements were developed. Based on these models, four numerical simulations were carried out. The numerical results were validated against the experimental ones and a very good...
-
Energy losses reduction in the medium voltage cable line – case study
PublicationThe paper presents an analysis of energy losses in a power cable system, which is composed of two 30 kV cable lines. This cable system is located at the seaside holiday area, so the load profile during a year is specific. Energy losses related to reactive power transmission, as well as to currents induced in the sheaths of the cables, are subject to analysis. Measurements were made in the system in order to prepare a computer model...
-
Efektywność działania wapna hydratyzowanego w betonie asfaltowym
PublicationW artykule przedstawiono ocenę efektywności działania wapna hydratyzowanego w betonie asfaltowym na podstawie analizy wyników badań laboratoryjnych i terenowych z odcinka doświadczalnego. Wykonano badania odporności na działanie wody i mrozu, odporności na deformacje trwałe oraz oceny stanu nawierzchni, równości poprzecznej i szorstkości odcinka doświadczalnego, gdzie w dwóch sekcjach odpowiednio wbudowano beton asfaltowy z dodatkiem...
-
Plomba w betonie. Systemy do naprawy kanalizacji
PublicationNowoczesne rozwiazania stosowanych w kanalizacji systemów naprawczych.
-
Determining the Mechanical Properties of Solid Plates Obtained from the Recycling of Cable Waste
Publication -
Motor Cable Effect on the Converter Fed AC Motor Common Mode Current
PublicationAnaliza zaburzeń elektromagnetycznych przewodzonych w przekształtnikowych układach napędowych wymaga uwzględniania pojemności pasożytniczych występujących w przekształtniku, uzwojeniach silnika oraz kablu zasilającym silnik. Dynamiczne zmiany napięć na uzwojeniach silników zasilanych z przekształtników częstotliwości PWM oraz związane bezpośrednio z nimi składowe wspólne prądów zaburzeń przewodzonych są istotnie związane z zjawiskami...
-
The Laboratory Stand for the Evaluation of Heat Dissipation from the Power Cable in a Casing Pipe
PublicationThe current carrying capacity of a power cable determines its efficiency, which depends on its capability to dissipate heat produced inside the cable, as a result of current flow, into the surrounding. The studies were conducted to determine how the characteristics of the medium around the cable affected its temperature and, as a result, its ability to transport electricity. The experimentation in the lab and real measurements...
-
Experiment-Based Study of Heat Dissipation from the Power Cable in a Casing Pipe
PublicationThe paper deals with the important challenges in terms of electricity transmission by means of underground cable lines. The power cable’s performance is characterized by an ampacity that represents its maximum electric current-carrying capacity. The ampacity of power cables depends on their ability to diffuse the heat generated by the current flow into the environment. In the performed research, the analysis of the efficiency of...
-
Experimental and numerical analysis of the modified TB32 crash tests of the cable barrier system
PublicationRoad restraint systems, including safety barriers, are one of the means used to improve road safety. Currently, they can be allowed to general use after passing the specific crash tests. However, it is always important and desirable to evaluate their performance under various realistic conditions, which can happen on the roads. In this study, the behaviour of the cable barrier system in impact conditions different than assumed...
-
Analysis of Induced Voltages and Power Losses in High Voltage Power Cables for Selected Methods of Cables Sheaths Bonding
PublicationPower is increasingly supplied to city centres with 110 kV cable lines. This is a convenient way to supply power, and practically the only one possible in areas of dense urban development. A high-voltage cable contains a coaxial metallic sheath, in which in normal operation and in fault conditions (during short-circuits) significant line-to-earth voltages can be induced, which threatens electric shock and/or damage to the cable’s...
-
Computer-aided Analysis of Induced Sheath Voltages in High Voltage Power Cable System
PublicationThis paper concerns the effect of configuration of high voltage power cables on induced voltages in their metallic sheaths. One, two or three cables per phase and phase sequence of the cables are considered. Computing of the voltages was performed for a normal operation and in case of earth fault. Various ways of the sheaths bonding are considered as well. Shock hazard and voltage stress of non-metallic outer sheath of cables are...
-
Cable stayed bridge over Vistula river in Plock. Dynamic analysis and site test
PublicationBudowę mostu przez rzekę Wisłę w Płocku ukończono w 2006 roku. Główne przęsło o długości 375 m zaprojektowano jako stalową konstrukcję podwieszoną. W celu weryfikacji konstrukcji zbudowano przestrzenny model MES. Badano zachowanie się konstrukcji mostu pod wpływem statycznego i dynamicznego obciążenia. W dalszym etapie przeprowadzono badania in - situ weryfikujące analizy numeryczne oraz założenia projektowe. Na bazie modelu MES...
-
Optimum number of actuators to minimize the cross-sectional area of prestressable cable and truss structures
PublicationThis paper describes a new computational method for determining the optimum number of actuators to design the optimal and economic cross-sectional area of pin-jointed assemblies based on the conventional force method. The most active members are selected to be prestressed to redistribute stress in the whole structure, resulting in regulating the internal force of bars that face high stress. Reducing stress in critical members allows...
-
Cerclage cable augmentation does not increase stability of the fixation of intertrochanteric fractures. A biomechanical study
PublicationBackground: Intertrochanteric fractures with a posteromedial intermediate fragment are unstable because of the loss of medial support. Additional fixation with a cerclage is used in subtrochanteric fractures, but not in intertrochanteric fractures. The aim of this biomechanical study is to evaluate whether cerclage fixation improves stability of intertrochanteric fractures. Hypothesis: Our hypothesis is that the cerclage fixation...
-
DETERMINATION OF ADDITIONAL TENSION IN TOWED STREAMER CABLE TRIGGERED BY COLLISION WITH UNDERWATER MOVING OBJECT
PublicationThe paper deals with issues connected with the behaviour of a streamer cable towed by a survey seismic vessel when the cable undergoes a strike triggered by collision with an underwater moving object. The consequences of such collisions may be both threat to the life of marine animals or damage to underwater units and large economic losses suffered by vessel owners. The risk of such collisions has increased over the last years...
-
Design of power cable lines partially exposed to direct solar radiation – special aspects
PublicationPower cable lines are usually buried in the ground. However, in some cases, their ending sections are mounted along the supports of overhead lines. This leads to a situation where the cables are exposed to direct solar radiation and, consequentially, overheat. The paper presents the advanced computer modelling of power cables’ heating, considering their insolation as well as the effect of wind. The temperature and current-carrying...
-
Overheating of underground power cable line due to its partial exposition to solar radiation
PublicationCurrent-carrying capacity of underground power cable lines depends, among others, on thermal resistivity of the soil and cables layout: trefoil formation, flat formation with or without spacing. If conditions for heat transfer in the ground are favorable, the current-carrying capacity is relatively high. Therefore, it generates risk of the power cables overheating, if part of the cable line is located vertically in the air, to...
-
Elektroenergetyczne kable hybrydowe z włóknami światłowodowymi.
PublicationPrzedstawiono opracowane konstrukcje kabli energetycznych z wbudowanymi włóknami światłowodowymi. Zaprezentowano i omówiono przeprowadzone badania wykonanego prototypu, oceniono możliwości zastosowań w sieci telekomunikacyjnej i pomiarowej oraz dla sterowania wyposażeniem budynków inteligentnych monitoringu obiektów chronionych i świadczenia telekomunikacyjnych usług szerokopasmowych, w tym usług multimedialnych. Omówiono...
-
Możliwość wykorzystania popiołów z osadów ściekowych w betonie
PublicationIlość popiołów lotnych ze spalania osadów ściekowych rośnie na całym świecie. Ich unieszkodliwianie jest poważnym problemem ekologicznym. W pracy przedstawiono ocenę możliwości wykorzystania popiołów lotnych z osadów ściekowych w betonie. Wykonano dwie serie badawcze dla dwóch współczynników (w/s) równych 0,49 oraz 0,55 z udziałem 10% i 20% popiołu lotnego (SSA), jako zamiennika cementu. Skład chemiczny wykazał, że popiół (SSA)...
-
Numerical studies on the influence of selected construction features and road conditions on the performance of road cable barriers
PublicationCable barriers are commonly used on Polish roads, including motorways and local roads. Their main elements are pre-stressed wire ropes, which are usually anchored at two ends in concrete blocks buried in the soil. In this work numerical studies concerning the influence of selected construction features and parameters of the vehicle motion on the performance of cable barriers were performed. Numerical simulations are a useful tool...
-
Modeling of Common Mode Currents Induced by Motor Cable in Converter Fed AC Motor Drives
PublicationInvestigation of conducted EMI generation in AC motor fed by pulse width modulated frequency converters requires to consider parasitic capacitances in converters, motor windings and feeding cables to be taken into account. Motor voltage transients and related common mode currents are significantly correlated with resonance effects occurring in load circuits. An analysis of frequency converter load impedance-frequency characteristics...
-
Attempt to a Video-Transmission Capability in MV Mine Cable Network Using BPL-PLC Technology
PublicationThis article presents and discusses the attempt to transmit video content using the BPL-PLC (Broadband over Power Line - Power Line Communication) technology. It includes simulation results of a specially developed digital transmitter and receiver, dedicated to a given predefined 6 kV mining power cable. The effect of two different transmission modes (2-7 MHz and 3-7.5 MHz) and two types of coupling (capacitive-inductive and induction-inductive),...
-
Incomplete Cross-Bonding in the MV Line. Experience from the Operation of MV Single Cable Lines
PublicationCable lines are one of the basic components of power systems. Medium and high voltage cables mainly comprise a metallic sheath, which is concentric to the main core conductor. There are several operating schemes of such cable lines, which differ in the place of earthing of sheaths and the possible use of the sheaths and/or conductors crossing. The sheaths cross-bonding is typically done in two places of one cable line section,...
-
LS-DYNA simulations of the impacts of a 38-ton Heavy Goods Vehicle into a road cable barrier
PublicationNowadays, more and more attention is being paid to safety on roads and motorways. It is due to the continuous development of road and motorway network and a significant increase of the number of vehicles on roads. To meet the expectations of improving road safety in Poland, the Road Innovations Development (RID) research programme was implemented in 2016. The aim of the RID 3A - Road Safety Equipment (RoSE) project is a comprehensive...
-
Quality Evaluation of Voice Transmission Using BPL Communication System in MV Mine Cable Network
PublicationThis article presents results of a quality evaluation study, considering voice transmission in a 6 kV medium voltage cable network using the BPL (Broadband over Power Line) communication system. The tests are carried out under real mining conditions for the selected power cable without voltage, earthed at both sides. Such a method of monitoring work conditions is of great importance, especially during a disaster. Power cables are...
-
Włókna polimerowe jako alternatywa włókien stalowych stosowanych w betonie
PublicationBetony ze zbrojeniem strukturalnym należą do materiałów kompozytowych. Obecność włókien zwiększa wytrzymałość na rozciąganie i rozciąganie przy zginaniu, udarność, a także zapobiega powstawaniu mikrorys i spękań. W artykule omówiono podstawowe parametry włókien stalowych i makrowłókien polimerowych oraz ich wpływ na właściwości dojrzewającego i stwardniałego betonu. Szczególną uwagę zwrócono na zalety makrowłókien polimerowych...
-
Analysis of the design development of the sliding table saw spindles
PublicationProducers of sliding table saws constantly strive for improvement in sawing accuracy. One of the method is an upswing in a spindle behavior, since, it affects to a large degree sawing effects. The design development of sliding table saw spindles during the last quarter-century is presented. The spindle system of the modernized spindle of the sawing machine Fx550 is described.
-
Zasilanie urządzeń sieci Ethernet przez kable transmisyjne
PublicationW roku 2003 komitet IEEE zatwierdził standard 802.3af (PoE) specyfikujący zasady zasilania urządzeń końcowych przez standardowe kable ethernetowe. W roku 2008 ma zostać zatwierdzona nowa wersja PoE, tzw. PoE Plus (IEEE 802.3at). W pracy omówiono zasady zasilania urządzeń proponowane w standardzie PoE, wskazano na ograniczenia wprowadzone przez IEEE 802.3af, przedstawiono podstawowe rozszerzenia proponowane w nowym rozwiązaniu PoE...
-
Design of thermal cutting table - welding technology and construction
PublicationW referacie przedstawiono pionierską pracę dyplomową stopnia inżynierskiego, wykonaną przez dwoje studentów Wydziału Mechanicznego Politechniki Gdańskiej zgodnie z systemem CDIO (Conceive, Design, Implement, Operate). W ramach pracy studenci zaprojektowali stół do cięcia termicznego metali (rysunki i obliczenia wytrzymałościowe metodą elementów skończonych), opracowali technologię spawania stołu oraz samodzielnie go wykonali. Stół...
-
Semantic Driven Table Understanding in Born-Digital Documents
PublicationThis paper presents a new approach to table understanding, suitable for born-digital PDF documents. Advance beyond the current state of the art in table understanding is provided by the proposed reverse MVC method, which takes advantage of only partial logic structure loss (degradation) in born-digital PDF documents, as opposed to unrecoverable loss (deterioration) taking place in scan based PDF documents.
-
FE<sub>2</sub>(SO<sub>4</sub>)<sub>3</sub> and Bentonite Use to Reduce COD Indicators in Wastewater Containing Detergents
Publication -
Pounding mitigation of a short-span cable-stayed bridge using a new hybrid passive control system
PublicationThis paper investigates the effectiveness of a new hybrid passive control system on the seismic response of an existing steel cable-stayed bridge considering the pounding effect. The proposed hybrid passive control system comprises a seismic isolator and a metallic damper. The bridge is located in a high seismic zone and has suffered several damages including the earthquake-induced pounding damage during the 1988 earthquake....
-
Damage Analysis of Tensioning Cable Anchorage Zone of a Bridge Superstructure, Using CDP Abaqus Material Model
PublicationNumerical analysis of the tensioning cables anchorage zone of a bridge superstructure is presented in this paper. It aims to identify why severe concrete cracking occurs during the tensioning process in the vicinity of anchor heads. In order to simulate the tensioning, among others, a so-called local numerical model of a section of the bridge superstructure was created in the Abaqus Finite Element Method (FEM) environment. The...
-
Span's low damped vibrations and vibration's damping by modal disparity inducted by cable stays temporal addition
PublicationW pracy przedstawiono problem obecności słabo tłumionych drgań przęseł mostów wraz z metodą ich aktywnego tłumienia. Badania przeprowadzono korzystając z analizy numerycznej. Analizowany mechanizm zamodelowano korzystając z metody elementów skończonych. W praco przedstawiono zwarty opis wykorzystanej metody. Następnie, zbudowano dwa alternatywne modele, różniące się liczbą odciągów usztywniających przęsło. Wyznaczono postaci i...
-
Motor Cable Influence on the Conducted EMI Emission of the Converter Fed AC Motor Drive. - Vol. 1
PublicationInvestigation of conducted electromagnetic interference in AC motor drives fed by pulse width modulated voltage converters requires considering parasitic capacitances in converters, motor windings and feeding cables to be taken into account. Motor voltage transients and related conducted electromagnetic emission are significantly correlated with resonance effects occurring in load circuits. The levels of intensity of these phenomena...
-
Standardy zasilania urządzeń sieci ethernetowych przez kable transmisyjne
PublicationW pracy wskazano na problemy zasilania urzadzeń sieciowych, w szczególności konieczność budowania dedykowanych systemów zasilających. Przedstawiono standard IEEE 802.3af (komercyjna nazwa - Power over Ethernet (PoE))specyfikujący zasady zasilania urządzeń końcowych przez standardowe kable ethernetowe. Omówiono zasady zasilania urzdzeń proponowane w standardzie PoE, wskazano na ograniczenia wprowadzone przez IEEE 802.3af, zaprezentowano...
-
Shaking table experimental study on structural pounding during earthquakes
PublicationArtykuł przedstawia wyniki badań eksperymentalnych przeprowadzonych na stole wstrząsowym dotyczące zachowania się kolidujących ze sobą modeli konstrukcji podczas trzęsień ziemi. Wyniki te pokazują, iż zderzenia mogą prowadzić do znacznego wzrostu odpowiedzi konstrukcji, ale mogą mieć również pozytywny wpływ i częściowo wytłumić drgania. Ponadto, wyniki badań wskazują na istotny wpływ rodzaju materiału, z którego wykonane są elementy...
-
Estimation of Stresses in a Dry Sand Layer Tested on Shaking Table
PublicationTheoretical analysis of shaking table experiments, simulating earthquake response of a dry sand layer, is presented. The aim of such experiments is to study seismic-induced compaction of soil and resulting settlements. In order to determine the soil compaction, the cyclic stresses and strains should be calculated first. These stresses are caused by the cyclic horizontal acceleration at the base of soil layer, so it is important...
-
Simple model of rain wind induced vibrations of stayed cables.
PublicationAnalizowano prosty, liniowy model drgań kabli mostów wantowych pod obciążeniem wiatrem i deszczem. Zakłada się, iż częstotliwość ruchu górnej kropli po powierzchni kabla i częstotliwość kabla są równe oraz iż amplituda ruchu kropli dla danej prędkości wiatru są stałe. Otrzymane rezultaty są porównane z istniejącymi w literaturze wynikami badań eksperymentalnych. Podaje się analityczne związki służące do oszacowania tłumienia...
-
Problems of Connecting Wind Farms to the Power System with HV Cables
PublicationThis paper presents problems caused by connecting wind farms to a power system with high voltage cables. The author highlights possible problems with reactive power compensation, depending on the arrangement of the shunt reactor connection and settings of control systems for reactive power and voltage of the wind farm. The paper also discusses issues of increasing active power losses caused by a shunt reactor installation.
-
Position Estimation in Corridors Along the Coupled Mode of Radiating Cables
PublicationRadiating cables are mostly used to provide radio communication in tunnels or corridors, but they can also be used to estimate the position of a mobile terminal along the cable. In this paper, a measuring receiver’s position was estimated by measuring the difference in the direct signal’s reception time, which was generated by a transmitter connected to one end of the radiating cable, and the delayed signal retransmitted from another...
-
Waves in a short cable at low frequencies, or just hand-waving? What does physics say? (Invited paper)
PublicationWe address the question of low-frequency signals in a short cable, which are often considered as waves in engineering calculations. Such an assumption violates several laws of physics, but exact calculations can be carried out via linear network theory.
-
Fabrication and characterization of a TiBs@MCN cable-like photocatalyst with high photocatalytic performance under visible light irradiation
Publication -
Analiza możliwości wykorzystania trójosiowego stanu naprężenia w betonie ściskanych słupów żelbetowych.
PublicationW artykule przeprowadzono analizę możliwości wykorzystania trójosiowego stanu naprężeń ściskających w słupach uzwojonych i słupach CFST. Przeprowadzono także analizę możliwości zwiększenia efektywności uzwojenia i stalowego płaszcza przez zastosowanie betonu ekspansywnego. Przeprowadzone analizy opracowano na podstawie badań własnych autorów.
-
Niewłaściwe proporcje ''wypełniacz - asfalt'' w betonie asfaltowym możliwą przyczyną uszkodzeń nawierzchni
PublicationMastyks asfaltowy złożony z wypełniacza, asfaltu i drobnych ziaren piasku spaja kruszywo w nawierzchni asfaltowej. Z badań amerykańskich wynika, że iloraz zawartości wypełniacza do asfaltu powinien wynosić 0,6-1,6. Badania polskich nawierzchni, które uległy uszkodzeniom, wykazują że iloraz ten jest znacznie wyższy.
-
Wpływ redukcji grubości elementu betonowego na nośność kotew metalowych w betonie
PublicationGrubość elementu betonowego przyjęta z warunków wykonawczych, bez negatywnego wpływu naroży i krawędzi, jest wystarczająca do osiągnięcia nośności charakterystycznej jak dla elementu o standardowej wysokości minimalnej. Nie ma tu obawy o przedwczesne zniszczenie betonu przez rozłupanie. Aby uzyskać wymaganą nośność z uwzględnieniem wzajemnego rozstawu łączników i wpływem obecności krawędzi elementu należy przeprowadzić dodatkowe...
-
Induced sheath voltages in 110 kV power cables – case study
PublicationThis paper considers electric shock hazard due to induced sheath voltages in 110 kV power cables. The purpose of this paper is to find an optimal configuration of the power cable system, taking into account electric shock hazard and ability of the system to transfer maximal power. A computer simulations on a computer model of the local power system, comprising high voltage power cables, were carried out. This model enables to analyse...
-
Experimental dynamic study on a timber-frame house using shaking table
PublicationThe aim of this paper is to show the results of the shaking table experimental study concerning the behaviour of the model of the timber-frame house under earthquake excitation and impact loading. In order to determine the basic dynamic properties of the undamaged structure, the free vibration and the sweep-sine tests were first conducted. Then, the model was excited using the time history record of the El Centro earthquake of...
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublicationThe aim of the present paper is to show the results of the shaking table experimental study concerning the diagnosis of damage in a model of cylindrical steel tank with self-supported roof which is filled with liquid. During the tests, the base of the structure was excited under the harmonic loading with variable frequency. The tests were repeated for different stages of damage, which was introduced in the model by easing the bolts...
-
Standardy zasilania sieci ethernetowych przez kable transmisyjne - rozwój PoE
PublicationW artykule przedstawiono rozwój koncepcji zasilania urzadzeń sieciowych przez standardowe kable ethernetowe, w szczególnosci opisano standard IEEE 802.3at. Zanalizowano również zastosowania i perspektywy rozwoju rozwišzań ethernetowych w domach prywatnych i przemyśle.
-
Induced Sheath Voltages In 110 Kv Power Cables – Case Study
PublicationThe paper considers shock hazard due to induced sheath voltages in 110 kV power cables. Various configurations of the metallic sheaths bonding and earthing (single-point bonding, both-ends bonding, cross-bonding) are analysed. Taking into account shock hazard and ability of the system to power transfer an optimal configuration is proposed.
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublicationDiagnosis of damage in civil engineering structures has recently become an important issue in the safety assessment procedure. Among a number of different approaches, a method of measuring the changes in natural frequencies is one of the most effective indicators of global damage. It has been successfully applied to relatively small. structures, however, the tests on large structures are very difficult and the practical application...
-
The Effect of Protrusions on the Initiation of Partial Discharges in XLPE High Voltage Cables
PublicationThis paper is focusing on 3D Finite Elements Analysis (FEA) based modelling of protrusions as defects or imperfections in the XLPE high voltage cable. This study is aiming to examine the impact protrusions have on the initiation of partial discharges. Spherical and ellipsoidal protrusions with different sizes at the conductor screen of the high voltage cable is an essential content of this paper. In addition, a spherical gas-filled...
-
Numerical Analysis of TB32 Crash Tests for 4-cable Guardrail Barrier System Installed on the Horizontal Convex Curves of Road
PublicationHorizontal curves are one of the elements of road infrastructure where statistically a relatively high number of accidents have been reported. In the last ten years in Poland approx. 10% of all road accidents happened on horizontal curves of roads and was responsible for approx. 14% of all fatalities on Polish roads. Thus, this issue is important and requires extensive research and proper road safety treatments. One possible measure...
-
Conventional and unconventional yeasts able to grow on rapeseed meal hydrolysates
Publication -
Impact of configuration of earth continuity conductor on induced sheath voltages in power cables
PublicationIn high voltage power cable systems a problem of induced sheath voltages exist. Due to these voltages electric shock and damage of non-metallic outer sheath of the cables may occur. Exposure to voltage of the outer sheath may be very high in case of earth fault with high value of earth current. In order to reduce induced sheath voltages an earth continuity conductor (conductors) along power cables is applied. Configuration of this...
-
Shaking table experimental study on the effectiveness of polymer bearings for seismic isolation of structures
PublicationSeismic isolation has been recognised to be a very effective way of protecting structures from damage during earthquakes. It allows us to extend the natural period of the structure and therefore avoid resonance with the ground motion. Moreover, by increasing damping in the isolation devices, more energy can be dissipated and thus the structural response can be further reduced. The aim of this paper is to show the results of the...
-
Shaking table experimental study on diagnosis of damage and its evaluation in steel structure
PublicationCelem artykułu jest pokazanie wyników badań eksperymentalnych przeprowadzonych na stole sejsmicznym dotyczących identyfikacji uszkodzeń modelu dwukondygnacyjnej konstrukcji stalowej. Uszkodzenie zdefiniowano poprzez spadek sztywności i symulowano poprzez zamianę słupów modelu na elementy o mniejszym przekroju poprzecznym. Wyniki badań pokazują charakterystyczny spadek wartości naturalnych częstotliwości konstrukcji wraz ze wzrostem...
-
Shaking table experimental study on models of steel buildings with different types of joints
PublicationThe aim of this paper is to study the response of models of steel buildings with destroyed and non-destroyed joints. The study was conducted experimentally using the shaking table tests. Two steel models were considered. Several types of joints were taken into account: totally destroyed joints, partially destroyed joints, welded joints and joints stiffened with additional metal. Six ground motions were taken into account. The acceleration...
-
Inception and Propagation of Electrical Trees in the Presence of Space Charge in HVAC Extruded Cables
PublicationThis paper presents the space charge impact on the inception and propagation of electrical trees in cross-linked polyethylene (XLPE) insulation via simulations and experimentation. A 3D finite element analysis (FEA)-based modeling is proposed to simulate electrical trees via a needle embedded on the XLPE insulation. The proposed FEA model demonstrates the influence of the space charge magnitude and polarity on the initiation of...
-
The Design Development of the Sliding Table Saw Towards Improving Its Dynamic Properties
PublicationCutting wood with circular saws is a popular machining operation in the woodworking and furniture industries. In the latter sliding table saws (panel saws) are commonly used for cutting of medium density fiberboards (MDF), high density fiberboards (HDF), laminate veneer lumber (LVL), plywood and chipboards of different structures. The most demanded requirements for machine tools are accuracy and precision, which mainly depend on...
-
Optimization of thermal backfill configurations for desired high-voltage power cables ampacity
PublicationThe ampacity of high-voltage power cables depends, among others, on their core cross-sectional area as well as thermal resistivity of the thermal backfill surrounding the cables. The cross-sectional area of the power cables’ core is selected according to the expected power to be transferred via the cable system. Usually, the higher the power transfer required, the higher the cross-sectional area of the core. However, the cost of...
-
Effect of soil moisture on current-carrying capacity of low-voltage power cables
PublicationOne of the factors affecting current-carrying capacity of underground power cables is the thermal resistivity of soil. Its value in the close proximity of the cable is the most important, and for this reason, in some cases, the local soil is replaced with an another soil type or with a cement-sand mixture. The thermal resistivity of the soil is strongly affected by moisture, and in the case of a cement-sand mixture – as tested...
-
Risk of power cables insulation failure due to the thermal effect of solar radiation
PublicationLow-voltage, as well as high-voltage power cable lines, are usually buried in the ground. The ampacity of the power cables in the ground mainly depends on the thermal resistivity of the soil, which may vary in a wide range. A common practice in power cable systems performance is to supply them from a pole of an overhead line. If so, a section of the line is located in free air and can be directly exposed to solar radiation. In...
-
Analysis of passenger car crash with a cable barrier installed with anti-glare screens on a horizontal convex road curve with 400 m radius
PublicationHigh-tension cable barriers have been used on roads for a relatively short period compared with other types of road barriers. Hence, there remains a need for further research on various crash scenarios. An important issue is the performance of a cable barrier on a road curve, particularly when a vehicle impacts the convex side of the barrier. To address this issue, the analysis in this study considers a system of anti-glare screens...
-
CFD-based evaluation of current-carrying capacity of power cables installed in free air
PublicationEvaluation of current-carrying capacity of power cables and selection of cross-sectional area of their conductors are mainly performed in accordance with requirements of EN, IEC or IEEE standards. However, these standards do not provide all methods of cables installation and location which occur in practice. Thus, in some cases, performance of advanced modeling of various thermal phenomena, affecting power cables current-carrying...
-
Ampacity of power cables exposed to solar radiation – recommendations of standards vs. CFD simulations
PublicationThe aim of the paper is to evaluate the ampacity of a low-voltage single power cable according to: 1) recommendations of the standard IEC 60287, 2) a Computational Fluid Dynamics method, implemented in Ansys software; and comparison of the results obtained for these two cases. Moreover, limitations of recommendations of the above mentioned standard are indicated.
-
Shaking table experimental study on damage mechanism of the disconnecting switch under seismic excitation
PublicationThe efficiency of the energetic network is a very import safety issue in the region experienced by the earthquake. High voltage disconnecting switches are important elements of the energetic infrastructure used to separate electric circuits (i.e. during repairs), which should not be damaged remaining fully operational. The aim of the paper is to show the results of the shaking table experimental investigation focused on damage...
-
Impact of thermal backfill parameters on current-carrying capacity of power cables installed in the ground
PublicationProper design of power installations with the participation of power cables buried in homogeneous and thermally well-conductive ground does not constitute a major problem. The situation changes when the ground is non-homogeneous and thermally low-conductive. In such a situation, a thermal backfill near the cables is commonly used. The optimization of thermal backfill parameters to achieve the highest possible current-carrying capacity...