Filtry
wszystkich: 1242
wybranych: 940
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: HARMONIC ANALYSIS , CONTROL SYSTEMS , STATORS , VOLTAGE CONTROL , ELECTROMAGNETICS , TORQUE , ROTORS
-
Open-transistor fault diagnostics in voltage-source inverters by analyzing the load current
PublikacjaA novel method is presented for the detection andisolation of open-transistor faults in voltage-source invertersfeeding low-power AC motors. The method is based onmonitoring two diagnostic signals, one indicating sustained nearzerovalues of output current and thus permitting fault detection,the other permitting the isolation of the particular transistorwhich went faulty. The latter signal is the ratio of the averagephase current...
-
Remote current measurement with FPGA digital processing
PublikacjaThe work presents an implementation of a modular measurement and control systemthat controls variants of mains supply of 230V electrical equipment. The system allowsto supervise power consumption in the office electronic equipment. The system detectsthe instant of the reduced power consumption by a device and makes possible itsswitch-off in order to reduce energy cost. The current is measured with integratedcurrent/voltage converters....
-
A pilot study to assess manufacturing processes using selected point measures of vibroacoustic signals generated on a multitasking machine
PublikacjaThe article presents the method for the evaluation of selected manufacturing processes using the analysis of vibration and sound signals. This method is based on the use of sensors installed outside the machining zone, allowing to be used quickly and reliably in real production conditions. The article contains a developed measurement methodology based on the specific location of microphones and vibration transducers mounted on...
-
Innovative Bidirectional Isolated High-Power Density On-Board Charge for Vehicle-to-Grid
PublikacjaThis paper deals with developing and implementing a bidirectional galvanically isolated on-board charger of a high-power density. The power density of the new charger was 4 kW/kg and 2.46 kW/dm3, and the maximum efficiency was 96.4% at 3.4 kW. Due to the requirement to achieve a high-power density, a single-stage inverter topology was used. Regarding switching losses, due to the topology of the circuit with so-called hard switching,...
-
Redundantly Actuated 3RRR Parallel Planar Manipulator - Numerical Analyses of its Dynamics Sensitivity on Modifications of its Platform’s Inertia Parameters
PublikacjaIn the paper, numerical analyses, as well as dynamics of a complex mechanism, are presented. Two objectives are crucial for the paper: inverse dynamic model is needed (dedicated to be use in the model predictive controller); an identification method is searched (some trajectory parameters are controlled, when specific trajectory is tracked under an open-loop model-based control), as selected parameters must be identified for the...
-
The Simulation of Activated Sludge System for Optimization of Predictive Aeration at Large WWTP
PublikacjaEffective use of biodegradable substrates as an internal carbon sources (ICS) for denitrification and EBPR and predicting performance of aeration systems during nitrification in activated sludge bioreactors, may be useful in realization the sustainable development by potentially saving energy consumption at WWTPs. A large number of WWTPs use activated sludge systems with an integrated removal of carbon, nitrogen and phosphorus...
-
Regulacja napięcia w sieci nN z rozproszonymi źródłami energii
PublikacjaPodłączanie rozproszonych źródeł energii do sieci energetycznych niskiego napięcia powoduje powstawanie problemów zmienności i niesymetrii napięcia, zwłaszcza w przypadku dużych odległości od transformatora zasilającego. W skrajnych przypadkach zachodzi konieczność redukcji mocy generowanej przez źródło podczas oddawaniu energii do sieci. Rozwiązaniem tego problemu jest zastosowanie energoelektronicznego regulatora napięcia składającego...
-
Comparison of Two Nonlinear Predictive Control Algorithms for Dissolved Oxygen Tracking Problem at WWTP
PublikacjaThe wastewater treatment plant is classified as a complex system, due to its nonlinear dynamics, large uncertainty of disturbance inputs, multiple time scales in the internal process dynamics, and multivariable structure. The aeration process, in turn, is an important and expensive part of wastewater treatment plant operation. All operating parameters of the aeration in biological processes are to be precisely controlled to provide...
-
Wieloobszarowa regulacja systemu turbogeneratora elektrowni jądrowej =Multiregional control of nuclear power plant turbogenerator system
PublikacjaW artykule przedstawiono propozycję zaawansowanej struktury sterowania układem turbogeneratora w szerokim zakresie zmian zapotrzebowania na moc czynną. Dla potrzeb syntezy tej struktury wykorzystano nieliniowe, dynamiczne modele turbiny parowej i generatora synchronicznego współpracującego z systemem elektroenergetycznym. Zaproponowane algorytmy sterowania oparte są odpowiednio o wieloobszarowe regulatory rozmyte, z lokalnymi regulatorami...
-
MultiRegional PCA for leakage detection and localisation in DWDS - approach
PublikacjaMonitoring is one of the most important parts in advanced control of complex dynamic systems. Information about systems behavior, including failures indicating, enables for efficient control. The chapter describes an approach to detection and localisation of pipe leakage in Drinking Water Distribution Systems (DWDS) representing complex and distributed dynamic system of large scale. Proposed MultiRegional Principal Component Analysis...
-
Analysis of volatile fraction of hybrid fruit pulp using Proton Transfer Reaction - Time-Of-Flight Mass Spectrometry
PublikacjaFruits and vegetables are important ingredients in human diet. Because of this, it is very important to know their exact composition and to control their quality. Based on the aroma of food products, it is possible to pre-evaluate their quality and freshness. The aim of this work was to characterize the volatile fraction of the hybrid fruit ‘sweetie’ using the modern analytical device PTR-TOFMS. Hybrid fruit samples are human-made...
-
Quantitative assessment
PublikacjaThe main trends in the development of analytical chemistry are the determination of increasingly lower concentrations of analytes in samples with complex matrix composition (trace analysis). While the obtained analytical results must be reliable, which means that they must accurately (truly and precisely) reflect the actual content of analytes in a representative sample of the material object under study. However, it is an extremely...
-
Knowledge-based functional safety management using ProSIL software
PublikacjaIn the article the ProSIL software for computer aided functional safety management is presented. The software consists of three modules for the determination of the required SIL level (ProSILen) and verification of the SIL level (ProSILver). In the ProSIL the calibrated knowledge-based risk graph method for determining the required safety integrity level (SIL) of the safety functions identified in hazard analysis is implemented....
-
Improving Output Performance of the Ultrasonic Multicell Piezoelectric Motor by Development the Multi-Rotor Structure
PublikacjaIn recent years, many researches have been carried out on piezoelectric multi-rotor structures. This paper describes the analysis, development and experimental process of an ultrasonic multi-cell piezoelectric motor using a multi-rotor structure. In this design, three independent cells have been integrated into a mechatronic system. Analytical model and finite element method are used for modal and dynamic analysis of the proposed...
-
Rozprzestrzenianie się w podtorzu skutków katastrof kolejowych z udziałem materiałów niebezpiecznych
PublikacjaDuża część przewozów materiałów niebezpiecznych prowadzona jest koleją. W związku z tym bezpieczeństwo tych przewozów nabiera coraz większego znaczenia. Każda katastrofa z udziałem materiałów niebezpiecznych ma negatywny wpływ na uczestników tego zdarzenia oraz na otaczające środowisko, bowiem jej zasięg na ogół nie jest lokalny. Z tego wynika, że w przypadku zaistnienia katastrofy należy minimalizować jej skutki oraz w dalszych...
-
Power System Stabilizer as a Part of a Generator MPC Adaptive Predictive Control System
PublikacjaIn this paper, a model predictive controller based on a generator model for prediction purposes is proposed to replace a standard generator controller with a stabilizer of a power system. Such a local controller utilizes an input-output model of the system taking into consideration not only a generator voltage Ug but also an additional, auxiliary signal (e.g., α, Pg, or ωg). This additional piece of information allows for taking...
-
Opomiarowanie w nowoczesnej oczyszczalni ścieków
PublikacjaArtykuł jest kolejną publikacja cyklu prezentującego wyniki projektu 5. Programu Ramowego UE ''SMArt Control of wastewater systems - SMAC''. W ramach tego projektu zaproponowano nową koncepcję sterowania biologiczną oczyszczalnią ścieków (OŚ)oraz opracowano nową strukturę i algorytmy sterowania. Wyniki projektu zostały zaimplementowane w pilotażowej oczyszczalni w Kartuzach.
-
Stormwater runoff in the urbanized coastal basin of Gdańsk Urbanized basin of Gdańsk
PublikacjaAnthropopressure strongly affects the primal water cycle. Alternation of the natural basins imposes changes of drainage patterns, reduction of bioretention, infiltration and base flow. As a result the overland flow predominates and greater runoff rates flow into storm water collection systems and reservoirs. Moreover changing climatic conditions increase the frequency of rapid extreme weather events. Infrastructures of urban areas...
-
Systemy bezprzewodowej łączności i transmisji danych dla potrzeb bezpieczeństwa publicznego (studium stanu i rozwiązań)
PublikacjaW niniejszym rozdziale przedstawiono charakterystyki rozwiązań użytkowych zrealizowanych w Katedrze Systemów i Sieci Radiokomunikacyjnych Politechniki Gdańskiej. Autorzy scharakteryzowali opracowane przez zespół badawczy Katedry, systemy bezprzewodowego monitoringu zagrożeń bezpieczeństwa oraz zarządzania i sterowania infrastrukturami krytycznymi. W tym też kontekście omówiono następujące systemy i aplikacje użytkowe: − globalny...
-
Bezpieczeństwo funkcjonalne i ochrona informacji w obiektach i systemach infrastruktury krytycznej - analiza i ocena
PublikacjaW niniejszym rozdziale monografii przedstawiono bardzo aktualną problematykę związaną z analizą bezpieczeństwa funkcjonalnego rozproszonych systemów sterowania i automatyki zabezpieczeniowej w obiektach infrastruktury krytycznej, wykorzystujących przemysłową sieć komputerową, z uwzględnieniem zagadnień ochrony informacji. W obiektach tego typu systemy sterowania i automatyki zabezpieczeniowej są projektowane jako systemy rozproszone,...
-
Evaluation of Open Source SIEM for Situation Awareness Platform in the Smart Grid Environment
PublikacjaThe smart grid as a large-scale system of systems has an exceptionally large surface exposed to cyber-attacks, including highly evolved and sophisticated threats such as Advanced Persistent Threats (APT) or Botnets. When addressing this situation the usual cyber security technologies are prerequisite, but not sufficient. The smart grid requires developing and deploying an extensive ICT infrastructure that supports significantly...
-
Human Factors and Cognitive Engineering in Functional Safety Analysis
PublikacjaHuman factors and cognitive engineering are considered nowadays as important multidisciplinary domains that focus on improving the relations between humans, technology and systems to be supervised and operated. The industrial automation and control systems (IACS) in hazardous plants are increasingly computerized and perform various safety functions. These are usually designed and implemented according to the functional safety requirements....
-
Quality assurance of alcoholic beverages by electronic nose
PublikacjaQuality is very important attribute of every alcoholic beverage. It is very significant to satisfy consumers and assure food quality. Flavour, colour and taste constitute a great matter not only for connoisseurs. Due to these features, the whole manufacturing process need to be monitored. This paper presents a high-class devices useful in assessing of beverage quality. Electronic noses offer quick real-time analysis, which is very...
-
Arm EMG Wavelet-Based Denoising System
PublikacjaThese paper presents research results of muscle EMG signal denoising. In the same time two muscles were examined - an adductor muscle (biceps brachii) and an abductor muscle (tricpeps brachii). The EMG signal was filtered using the wavelet transform technique, having selected the crucial parameters as: wavelet basis function (Daubechies 4), 10 th decomposition level, threshold selection algorithm (Heurestic) and a sln rescaling...
-
Robust Parameter Estimation and Output Prediction for Reactive Carrier-Load Nonlinear Dynamic Networks
PublikacjaIn this paper an extension of on-line model simplification technique for a class of networked systems, namely reactive carrier-load nonlinear dynamic networked system (RCLNDNS), kept within point-parametric model (PPM) framework is addressed. The PPM is utilised to acquire a piece wise constant time-varying parameter linear structure for the RCLNDNS suitable for the on-line one step ahead prediction that may be applied to monitoring...
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
Patch size setup and performance/cost trade-offs in multi-objective EM-driven antenna optimization using sequential domain patching
PublikacjaPurpose This paper aims to assess control parameter setup and its effect on computational cost and performance of deterministic procedures for multi-objective design optimization of expensive simulation models of antenna structures. Design/methodology/approach A deterministic algorithm for cost-efficient multi-objective optimization of antenna structures has been assessed. The algorithm constructs a patch connecting extreme Pareto-optimal...
-
ECU calibration for gaseous dual fuel supply system in compression ignition engines
PublikacjaThe dual fuel (DF) combustion mode is proven solution that allows to improve or get at the same level engine performance and reduce toxic compounds in exhaust gases which is confirmed by researchers and end-users. DF combustion mode uses two fuels gaseous fuel as a primary energy source and a pilot quantity of diesel fuel as ignition source. However, in order, to fully take advantage of the potential of the dual fuel mode, DF system...
-
Incomplete Cross-Bonding in the MV Line. Experience from the Operation of MV Single Cable Lines
PublikacjaCable lines are one of the basic components of power systems. Medium and high voltage cables mainly comprise a metallic sheath, which is concentric to the main core conductor. There are several operating schemes of such cable lines, which differ in the place of earthing of sheaths and the possible use of the sheaths and/or conductors crossing. The sheaths cross-bonding is typically done in two places of one cable line section,...
-
Sensing Direction of Human Motion Using Single-Input-Single-Output (SISO) Channel Model and Neural Networks
PublikacjaObject detection Through-the-Walls enables localization and identification of hidden objects behind the walls. While numerous studies have exploited Channel State Information of Multiple Input Multiple Output (MIMO) WiFi and radar devices in association with Artificial Intelligence based algorithms (AI) to detect and localize objects behind walls, this study proposes a novel non-invasive Through-the-Walls human motion direction...
-
System SCADA w nowoczesnym monitorowaniu i sterowaniu oczyszczalnią ścieków
PublikacjaArtykuł jest kolejną publikacją z cyklu prezentującego wyniki projektu 5. Programu Ramowego UE ''SMART Control of wastewater systems - SMAC''. W ramach tego projektu zaproponowana została nowa koncepcja sterowania biologiczną oczyszczalnią ścieków (OŚ) oraz opracowana została nowa struktura i algorytmy sterowania. Wyniki projektu zostały zaimplimentowane w pilotażowej oczyszczalni w Kartuzach.
-
Koncepcja analizy stanów emocjonalnych użytkowników w kontekście systemów zabezpieczeń transportowych
PublikacjaAutorzy, przywołując własne i światowe badania nad rozpoznawaniem emocji ludzkich z obrazu twarzy, wskazują na możliwość zastosowania algorytmów komputerowych i ich implementacji w komputerach osobistych (i innych urządzeniach personalnych wyposażonych w dostatecznie silny procesor obliczeniowy). Zastosowanie takiego rozwiązania może poprawić bezpieczeństwo użytkowania urządzeń, maszyn i pojazdów, których operatorzy muszą gwarantować...
-
Business continuity management framework for Industry 4.0 companies regarding dependability and security of the ICT and ICS/SCADA system
PublikacjaThis chapter addresses a business continuity management (BCM) framework for the Industry 4.0 companies including the organizational and technical solutions, regarding the dependability and security of the information and telecommunication technology (ICT), and the industrial control system (ICS) / supervisory control and data acquisition (SCADA) system. These technologies and systems play nowadays important roles in modern advanced...
-
Approximation of Fractional Order Dynamic Systems Using Elman, GRU and LSTM Neural Networks
PublikacjaIn the paper, authors explore the possibility of using the recurrent neural networks (RNN) - Elman, GRU and LSTM - for an approximation of the solution of the fractional-orders differential equations. The RNN network parameters are estimated via optimisation with the second order L-BFGS algorithm. It is done based on data from four systems: simple first and second fractional order LTI systems, a system of fractional-order point...
-
Autoencoder application for anomaly detection in power consumption of lighting systems
PublikacjaDetecting energy consumption anomalies is a popular topic of industrial research, but there is a noticeable lack of research reported in the literature on energy consumption anomalies for road lighting systems. However, there is a need for such research because the lighting system, a key element of the Smart City concept, creates new monitoring opportunities and challenges. This paper examines algorithms based on the deep learning...
-
Structure and the space vector modulation for a medium-voltage power-electronic-transformer based on two seven-level cascade H-bridge inverters
PublikacjaThis study presents the structure and the space vector pulse-width modulation (SVPWM) for power electronic transformer (PET) based on two seven-level cascade H-bridge (CHB) inverters. The DC links of CHB inverters are coupled with nine dual-active bridge (DAB) converters with medium-frequency transformers. The DC-link voltages are equalised with two methods – through the control of DAB voltages...
-
Testing sensitivity of A-type residual current devices to earth fault currents with harmonics
PublikacjaIn many applications, modern current-using equipment utilizes power electronic converters to control the consumed power and to adjust the motor speed. Such equipment is used both in industrial and domestic installations. A characteristic feature of the converters is producing distorted earth fault currents, which contain a wide spectrum of harmonics, including high-order harmonics. Nowadays, protection against electric shock in...
-
A CONCEPT DESIGN OF DIESEL – HYDRAULIC PROPULSION SYSTEM FOR PASSENGER SHIP INTENDED FOR INLAND SHALLOW WATER NAVIGATION
PublikacjaThis paper presents an analysis of environmental and technical conditions necessary for working out a possibly most favourable propulsion system for a two – segment passenger ship intended for navigation between Berlin and Kaliningrad. There are presented various types of propulsion systems for small ships as well as analyzed their possible applications and consequences. In this work there were taken into account system’s reliability,...
-
DETERMINATION OF VERTICAL DISPLACEMENTS IN RELATIVE MONITORING NETWORKS
PublikacjaThe problem of determining displacements of objects is an important and current issue, in particular in terms of operational safety. This is a requirement that covers geodetic, periodic control measurements in order to determine horizontal and vertical displacements. The paper is focused on the analysis of vertical displacements. Geodetic measurements and their interpretation allow to reduce the risk of possible structural catastrophes....
-
Current risk analysis and management issues in technical systems.
PublikacjaDealing with the reliability and safety of industrial hazardous plants requires taking into account relevant interdisciplinary scientific knowledge and some existing approaches based on so-called good engineering practice, also those included in the international standards and guidelines. In this article an approach is proposed how to integrate the functional safety concept with information security aspects in the design and management...
-
Reliable EM-driven size reduction of antenna structures by means of adaptive penalty factors
PublikacjaMiniaturization has become of paramount importance in the design of modern antenna systems. In particular, compact size is essential for emerging application areas such as internet of things, wearable and implantable devices, 5G technology, or medical imaging. On the other hand, reduction of physical dimensions generally has a detrimental effect on antenna performance. From the perspective of numerical optimization, miniaturization...
-
An Optimal Power Point Tracking Algorithm in a Solar PV Generation System
PublikacjaThe non-linearity in I-V characteristics of a PV panel requires to be operated at knee point to extract maximum power. In order to operate the panel at optimal point, maximum power point tracking (MPPT) algorithm is employed in the control structure. The main objective of MPP tracking is to keep the operation at knee point of I-V characteristics under varying condition of temperature and solar insolation. Under non uniform solar...
-
Direct modulation for conventional matrix converters using analytical signals and barycentric coordinates
PublikacjaThis paper proposes the generalized direct modulation for Conventional Matrix Converters (CMC) using the concept of analytical signals and barycentric coordinates. The paper proposes a novel approach to the Pulse Width Modulation (PWM) duty cycle computing, which allows faster prototyping of direct control algorithms. The explanation of the new idea using analytical considerations demonstrating the principles of direct voltage...
-
Application and modelling of Shape-Memory Alloys for structural vibration control: State-of-the-art review
PublikacjaOne of the most essential components of structural design for civil engineers is to build a system that is resistant to environmental conditions such as harsh chemical environments, and catastrophic disasters like earthquakes and hurricanes. Under these circumstances and disturbances, conventional building materials such as steel and concrete may demonstrate inadequate performance in the form of corrosion, deterioration, oxidizing,...
-
The Analysis of Patients' Airflow with Respect to Early Detection of Sleep Apnea
PublikacjaThe paper discusses the analysis of the respiratory events of sleep apnea patients. The analysis was carried out on the basis of the patient's airflow. As a result of the conducted analysis we proposed an algorithm which establishes an individual respiratory pattern for each subject. The algorithm could be implemented in the measurement - control system which manages the prosthetic device applying positive airway pressure. Its...
-
A nine-input 1.25 mW, 34 ns CMOS analog median filter for image processing in real time
PublikacjaIn this paper an analog voltage-mode median filter, which operates on a 3 × 3 kernel is presented. The filter is implemented in a 0.35 μm CMOS technology. The proposed solution is based on voltage comparators and a bubble sort configuration. As a result, a fast (34 ns) time response with low power consumption (1.25 mW for 3.3 V) is achieved. The key advantage of the configuration is relatively high accuracy of signal processing,...
-
Modelling of MV and HV Cable Lines
PublikacjaOverhead and cable lines are fundamental elements of power systems. Participation of cable lines is smaller and their percentage decreases as voltage is increased. HV cable lines are often built with the use of cables which are composed of coaxial metallic sheaths. Such cables are also often used in MV networks. The sheath may operate in different confgurations. In the case of Polish MV network the sheaths are earthed at both ends....
-
Robust identification of quadrocopter model for control purposes
PublikacjaThe paper addresses a problem of quadrotor unmanned aerial vehicle (so-called X4-flyer or quadrocopter) utility model identification for control design purposes. To that goal the quadrotor model is assumed to be composed of two abstracted subsystems, namely a rigid body (plant) and four motors equipped with blades (actuators). The model of the former is acquired based on a well-established dynamic equations of motion while the...
-
Static Shape and Stress Control of Trusses with Optimum Time, Actuators and Actuation
PublikacjaTraditional shape and stress control of structures use many actuators and require enormous time to find reasonable solutions that need designers to input specific target displacement and stress. This study employs a linear technique to static shape and stress control of pin-jointed assemblies as a theoretical advancement to prior works and provides a comparative analysis against previously established works. The study evaluates...
-
The Application of Vibration Recording and Analysis in Tribological Research on Sliding Friction
PublikacjaThe paper reports on a tribological research on the macroscopic manifestation and characteristics of sliding friction. The aim of the task was to measure friction in lubricated sliding contacts and test the interactions between the environment (the test rig) and the experimental friction contact. Friction-induced vibrations were observed and studied as a manifestation of the process. The typical set of velocity and force/torque...