Filtry
wszystkich: 1569
wybranych: 1462
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: multi-criterion rating
-
Impact of rotor geometry optimization on the off-design ORC turbine performance
PublikacjaThe paper describes the method of CFD based Nelder-Mead optimization of a 10 kW single-stage axial turbine operating in an ORC system working on R7100. The total-to-static isentropic efficiency is defined as an objective function. Multi-point linear regression is carried out to determine the significance of the objective function arguments and to pick up the set of particular variables and characteristic quantities (e.g. flow angles)...
-
Effect of power frequency on the stress state of disc actuator
PublikacjaThe paper presents the concept of determinig the optimum frequency of coil supply in inductive-dynamic drive. As a criterion to obtain the sought frequency, the smallest value of reduced stress in the disc was assumed while maintaining the desired dynamics.
-
Nierówności pionowe toru kolejowego
PublikacjaOcena jakości geometrycznej toru kolejowego wymaga od zarządców infrastruktury stosowania jednolitych metod pomiarów, obliczania i interpretacji wyników. W tym zakresie należy stosować się do norm europejskich i technicznych specyfikacje interoperacyjności. W artykule przedstawiono podstawowe zagadnienia związane z pomiarem i oceną nierówności pionowych toru kolejowego. Zapisano odchyłki dopuszczalne nierówności pionowych według...
-
Inseparability criteria based on matrices of moments
PublikacjaInseparability criteria for continuous and discrete bipartite quantum states based on moments of annihilationand creation operators are studied by developing the idea of Shchukin-Vogel criterion Phys. Rev. Lett. 95,230502 2005. If a state is separable, then the corresponding matrix of moments is separable too. Thus, wederive generalized criteria based on the separability properties of the matrix of moments. In particular, acriterion...
-
Performance of isotropic constitutive laws in simulating failure mechanisms in scaled RC beams
PublikacjaResults of numerical calculations of reinforced concrete (RC) beams are presented. Based on experimental results on longitudinally reinforced specimens of different sizes and shapes are investigated. Four different continuum constitutive laws with isotropic softening are used: one defined within continuum damage mechanics, an elasto-plastic with the Rankine criterion in tension and the Drucker-Prager criterion in compression, a...
-
Turning maneuver as a potential cause of the next stability failure mode for a ship in operation
PublikacjaThe only formal stability-related requirement referring to a turning maneuver of a ship results from the IS Codeand its application is limited to passenger ships only. The goal of the adopted criterion is to prevent an excessiveangle of heel in turn. Likewise, the remaining prescriptive criteria, this one is simply based on the concept ofa threshold that must not be exceeded. In this case, the angle of heel...
-
The use of fast molecular descriptors and artificial neural networks approach in organochlorine compounds electron ionization mass spectra classification
PublikacjaDeveloping of theoretical tools can be very helpful for supporting new pollutant detection. Nowadays, a combination of mass spectrometry and chromatographic techniques are the most basic environmental monitoring methods. In this paper, two organochlorine compound mass spectra classification systems were proposed. The classification models were developed within the framework of artificial neural networks (ANNs) and fast 1D and...
-
STUDY ON THE RELATIONSHIP BETWEEN VEHICLE MAINTENANCE AND FUEL CONSUMPTION
PublikacjaA contemporary road vehicle (RV) is a rather complex system, consisting of a large number of subsystems, assemblies, units, and elements (parts). While operating, an RV interacts with the environment, and its elements interact with each other. Consequently, the properties (parameters) of these elements change in the process - hardness, roughness, size, relative position, gapping, etc. A partial solution to the presented problems...
-
The external walls of a passive building: A classification anddescription of their thermal and optical properties
PublikacjaThis paper attempts a new classification of insulating materials from the perspective of their utility in thepro-ecological passive construction industry. The main criterion is the conductivity of thermal and solarenergy. Based on their ability to conduct or block fluxes of thermal and solar energy, six types of insulatingwalls are proposed. On the basis of this criterion there are traditional dividing walls (typical walls, wallinsulating...
-
Optimization of hybrid parallel application execution in heterogeneous high performance computing systems considering execution time and power consumption
PublikacjaMany important computational problems require utilization of high performance computing (HPC) systems that consist of multi-level structures combining higher and higher numbers of devices with various characteristics. Utilizing full power of such systems requires programming parallel applications that are hybrid in two meanings: they can utilize parallelism on multiple levels at the same time and combine together programming interfaces...
-
A Single-Carrier-Based Pulse-Width Modulation Template for Cascaded H-Bridge Multilevel Inverters
PublikacjaMultiplicity of the triangular carrier signals is a criterion for the extension of sinusoidal pulsewidth modulation, SPWM, to a number of output voltage levels per phase-leg in cascaded H-bridge (CHB) multilevel inverter (MLI). Considering medium and high voltage applications where appreciable number of output voltage levels from CHB MLI is needed, commensurate high number of carrier signals in either classical level- or phase-shifted...
-
Experimental verification and comparison of mode shape-based damage detection methods
PublikacjaThis paper presents experimental verification and comparison of damage detection methods based on changes in mode shapes such as: mode shape curvature (MSC), modal assurance criterion (MAC), strain energy (SE), modified Laplacian operator (MLO), generalized fractal dimension (GFD) and Wavelet Transform (WT).
-
A Control Theoretical Approach to Spectral Factorization is Unstable
PublikacjaLocal stability analysis of a recently proposed recursive feedback-based approach to spectral factorization is performed. The method is found not to give stability guarantees. Interestingly enough, its global behavior often allows one to obtain reasonable approximations of spectral factorizations if a suitable stopping criterion is employed.
-
The experimental and numerical investigation of fracture behaviour in PMMA notched specimens under biaxial loading conditions – Tension with torsion
PublikacjaThis paper presents the results of experimental fracture test of flat PMMA specimens under biaxial loading condition tension with torsion (proportional). The specimens were made in two thicknesses: 5 and 15 mm and were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. Thanks to the ARAMIS 3D 4 M non-contact vision system, measurement of the elongation and twist angle were recorded. During experimental...
-
On Noncausal Identification of Nonstationary Multivariate Autoregressive Processes
PublikacjaThe problem of identification of nonstationary multivariate autoregressive processes using noncausal local estimation schemes is considered and a new approach to joint selection of the model order and the estimation bandwidth is proposed. The new selection rule, based on evaluation of pseudoprediction errors, is compared with the previously proposed one, based on the modified Akaike’s final prediction error criterion.
-
Fusion-based Representation Learning Model for Multimode User-generated Social Network Content
PublikacjaAs mobile networks and APPs are developed, user-generated content (UGC), which includes multi-source heterogeneous data like user reviews, tags, scores, images, and videos, has become an essential basis for improving the quality of personalized services. Due to the multi-source heterogeneous nature of the data, big data fusion offers both promise and drawbacks. With the rise of mobile networks and applications, UGC, which includes...
-
Reliability assessment of an OVH HV power line truss transmission tower subjected to seismic loading
PublikacjaThe study focuses on the reliability of a transmission tower OS24 ON150 + 10, an element of an OVH HV power line, under seismic loading. In order to describe the seismic force, the real-life recording of the horizontal component of the El Centro earthquake was adopted. The amplitude and the period of this excitation are assumed random, their variation is described by Weibull distribution. The possible space state of the phenomenon...
-
Settlement of a historic building due to seepage-induced soil deformation
PublikacjaThe research paper reviews issues associated with the impact of groundwater flow on soil characteristics and parameters, hence, the entire structure of a building set on it. Water seepage through the ground, building subsoil or structural elements of buildings made of soil affects the soil skeleton and may lead to changes in the arrangement of individual grains relative to each other, i.e., a modified soil structure. Soil solid...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublikacjaThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
Design of Jack-up Platform for 6 MW Wind Turbine: Parametric Analysis Based Dimensioning of Platform Legs
PublikacjaThe article presents the results of the research conducted within the framework of the project entitled WIND-TU-PLA (ERA-NET, MARTEC II), the general aim of which was to design and analyse supporting structures for wind turbines intended for operation on the South Baltic area. The research part described in the article aimed at developing a preliminary design for a jack-up platform which can operate on water areas with depth of...
-
Regularized Identification of Time-Varying FIR Systems Based on Generalized Cross-Validation
PublikacjaA new regularization method is proposed and applied to identification of time-varying finite impulse response systems. We show, that by a careful design of the regularization constraint, one can improve estimation results, especially in the presence of strong measurement noise. We also show that the the most appropriate regularization gain can be found by direct optimization of the generalized cross-validation criterion.
-
Simulations of Shear Zones and Cracks in Engineering Materials Using eXtended Finite Element Method
PublikacjaNumerical simulations of cracks and shear zones in quasi-brittle materials are presented. Extended Finite Element Method is used to describe both cracks and shear zones. In a description of tensile cracks, a Rankine criterion is assumed. A discrete Mohr-Coulomb law is adopted for simulations of shear zones. Results of simple numerical tests: unixial tension, bending and biaxial compression are demonstrated.
-
Recognition, understanding and aestheticization of freehand drawing flowcharts
PublikacjaIn this paper a concept of FCA, a system for recognizing, understanding and aestheticization of freehand drawing flow charts is described. The system is based on a proposed by the author FlowGram graph grammar describing flow charts drawing. An open format FlowChartML for flow charts description is also proposed. The aestheticization criterion is formulated that allows for automatic beautification of flow charts. First experiments...
-
Direct detection of quantum entanglement
PublikacjaBasing on positive maps separability criterion we propose the experimentally viable, direct detection of quantum entanglement. It is efficient and does not require any a priori knowledge about the state. For two qubits it provides a sharp (i.e., “if and only if”) separability test and estimation of amount of entanglement. We view this method as a new form of quantum computation, namely, as a decision problem with quantum data structure.
-
On a Method of Efficiency Increasing in Kaplan Turbine
PublikacjaThis paper presents a method of increasing efficiency in Kaplan-type turbine. The method is based on blade profile optimisation together with modelling the interaction between rotor and stator blades. Loss coefficient was chosen as the optimisation criterion, which is related directly to efficiency. Global optimum was found by means of Genetic Algorithms, and Artificial Neural Networks were utilised for approximations to reduce...
-
The passive operating mode of the linear optical gesture sensor
PublikacjaThe study evaluates the influence of natural light conditions on the effectiveness of the linear optical gesture sensor, working in the presence of ambient light only (passive mode). The orientations of the device in reference to the light source were modified in order to verify the sensitivity of the sensor. A criterion for the differentiation between two states - "possible gesture" and "no gesture" - was proposed. Additionally,...
-
Numerical analyses of novel prefabricated structural wall panels in residential buildings based on laboratory tests in scale 1:1
PublikacjaThe paper presents experimental and numerical investigations on novel prefabricated composite building wall panels for residential building constructions. The wall panels were composed of reinforced concrete ribbed elements with the core from the EPS foam as the thermal insulation. The wall panels in the full-scale 1:1 were subjected to vertical loads. In the first step, the experiments were analysed with simple usual static methods....
-
Compensation of Voltage Drops in Trolleybus Supply System Using Battery-Based Buffer Station
PublikacjaThis paper analyzes the results of a trial operation of a battery-based buffer station supporting a selected section of trolleybus power supply systems in Pilsen, Czech Republic. The buffer station aims to prevent the catenary from excessive voltage drops in a part of the route that is most remote from the traction substation. Compensation of voltage drops is carried out by continuously measuring the catenary voltage and injecting...
-
Modeling and Designing Acoustical Conditions of the Interior – Case Study
PublikacjaThe primary aim of this research study was to model acoustic conditions of the Courtyard of the Gdańsk University of Technology Main Building, and then to design a sound reinforcement system for this interior. First, results of measurements of the parameters of the acoustic field are presented. Then, the comparison between measured and predicted values using the ODEON program is shown. Collected data indicate a long reverberation...
-
Semantic Integration of Heterogeneous Recognition Systems
PublikacjaComputer perception of real-life situations is performed using a variety of recognition techniques, including video-based computer vision, biometric systems, RFID devices and others. The proliferation of recognition modules enables development of complex systems by integration of existing components, analogously to the Service Oriented Architecture technology. In the paper, we propose a method that enables integration of information...
-
OPTIMISING RIG DESIGN FOR SAILING YACHTS WITH EVOLUTIONARY MULTIOBJECTIVE ALGORITHM
PublikacjaThe paper presents a framework for optimising a sailing yacht rig using Multi-objective Evolutionary Algorithms and for filtering obtained solutions by means of a Multi-criteria Decision Making method. A Bermuda sloop with discontinuous rig is taken under consideration as a model rig configuration. It has been decomposed into its elements and described by a set of control parameters to form a responsive model which can be used...
-
Effect of power frequency on the stress state of disc actuator
PublikacjaThis paper presents the concept of determining the optimum frequency of coil supply in inductive-dynamic drive. As a criterion to obtain the sought frequency, the smallest value of reduced stress in the disc was assumed while maintaining the desired dynamics. The disc stress is determined on the basis of solution of vibrating thin plate equation. Magnetic pressure acting on the disc is obtained from a hybrid circumferentially-field...
-
ON ESTIMATION OF OCCUPANT SAFETY IN VEHICULAR CRASHES INTO ROADSIDE OBSTACLES USING NON-LINEAR DYNAMIC ANALYSIS
PublikacjaThe article describes a comparison of two general methods of occupants safety estimation based on a numerical examples. The so-called direct method is mainly based on the Head Injury Criterion of a crash test dummy in a vehicle with passive safety system while the indirect method uses a European standards approach to estimate impact severity level. Numerical simulations in LS-DYNA have been conducted.
-
Project Team Management Supported by an Agent-Based Model
PublikacjaThis work is a continuation of a series of works about research into the use of multi-agent systems to support IT project management. Previous studies have shown the possibility of using a multi-agent in order to optimize management decisions concerning the selection of methods for project implementation. It was noted that the project manager's decisions are influenced by three fundamental parameters: the entropy of the project,...
-
High catalytic performance of laccase wired to naphthylated multiwall carbon nanotubes
PublikacjaThe direct electrical connection of laccase on the electrode surface is a key feature in the design of efficient and stable biocathodes. However, laccases can perform a direct electron transfer only when they are in the preferable orientation toward the electrode. Here we report the investigation of the orientation of Laccase from Amano on multi-walled carbon nanotube surface modified with naphthalene group. Naphthylated multi...
-
Application of MARKAL model to optimisation of electricity generation structure in Poland in the long-term time horizon Part I - concept of the model
PublikacjaIn this paper, which inaugurates a series of papers on this subject, a concept is proposed of a power system development model with regard to the technological structure of electricity generation in Poland, in the long-term time perspective – until 2060. The model is based on the mathematical structure of the MARKAL optimization package. The paper presents a brief description of the tool used in the model research. In addition,...
-
Software Agents for Computer Network Security
PublikacjaThe chapter presents applications of multi-agent technology for design and implementation of agent-based systems intended to cooperatively solve several critical tasks in the area of computer network security. These systems are Agent-based Generator of Computer Attacks (AGCA), Multi-agent Intrusion Detection and Protection System (MIDPS), Agent-based Environment for Simulation of DDoS Attacks and Defense (AESAD) and Mobile Agent...
-
The process of identification of the track's geometrical layout and the alignment project based on the of satellite measurements
PublikacjaIn the paper a methodology of restoring of railway track’s geometrical shape in a horizontal plane on the base of conducted mobile satellite surveying was presented. The authors proposed a calculating algorithm for designing the track sections placed in horizontal arcs. In the algorithm an analytical methodology with mathematical formulas is applied. The procedure has an universal character, i.e. provides the possibility of varying...
-
Satellite inventory of tram track geometrical layout
PublikacjaIn the paper a methodology of restoring of railway track’s geometrical shape in a horizontal plane on the base of conducted mobile satellite surveying was presented. The authors proposed a calculating algorithm for designing the track sections placed in horizontal arcs. In the algorithm an analytical methodology with mathematical formulas is applied. The procedure has an universal character, i.e. provides the possibility of varying...
-
Graph security testing
PublikacjaSet S ⊂ V is called secure set iff ∀ X ⊂ S | N [ X ] ∩ S | ≥ | N ( X ) \ S | [3]. That means that every subset of a secure set has at least as many friends (neighbour vertices in S) as enemies (neighbour vertices outside S) and will be defended in case of attack. Problem of determining if given set is secure is co −NP -complete, there is no efficient algorithm solving it [3]. Property testers are algorithms that distinguish inputs...
-
A method for evaluating durability of porous slide bearings
PublikacjaThe article presents the structures of porous bearings bushes and greasy lubricants, and the similarity criterion resulting from this structures. A phisical model is proposed which describes the operation of the porous slide bearing bush taking into account, via analogy, the phenomena taking place in the grease lubricant nodes instead of those observed in the bush structures.Included are the result of experimental tests of three...
-
Multicriteria decision analysis in ranking of analytical procedures for aldrin determination in water
PublikacjaThe study presents the possibility of multi-criteria decision analysis (MCDA) application when choosing analytical procedures with low environmental impact. A type of MCDA, Preference Ranking Organization Method for Enrichment Evaluations (PROMETHEE), was chosen as versatile tool that meets all the analytical chemists – decision makers requirements. Twenty five analytical procedures for aldrin determination in water samples (as...
-
Selection of effective cocrystals former for dissolution rate improvement of active pharmaceutical ingredients based on lipoaffinity index
PublikacjaNew theoretical screening procedure was proposed for appropriate selection of potential cocrystal formers possessing the ability of enhancing dissolution rates of drugs. The procedure relies on the training set comprising 102 positive and 17 negative cases of cocrystals found in the literature. Despite the fact that the only available data were of qualitative character, performed statistical analysis using binary classification...
-
4-Point beam tensile test on a soft adhesive
PublikacjaAn adhesive butt joint with a soft bondline has been studied. A series of experiments was conducted on test pieces constituted of aluminium adherends bonded with a low modulus epoxy adhesive, ScotchWeld™ 2216. The joint was subjected to four point bending, in tension/compression loading, under constant deflection rate, with the bondline being parallel to the applied load. The objective was to examine and evaluate crack nucleation...
-
Determining the leakage current resistive component by the orthogonal vector method
PublikacjaThe measurement of the metal – oxide surge arresters (MOSA) leakage current and the analysis of its components is a key diagnostic criterion according to technical standards. During on site MOSA condition assessment, the easy way is based on the measurement only leakage current, without the inconvenient live working measurements of supply voltage. Orthogonal vectors method of determination the resistive leakage current is presented....
-
GROUP COMPOSER - System for Modeling Agents’ Team Building for Tasks
PublikacjaMulti-agent systems consist of many autonomous units, called agents, that can interact when trying to achieve their goals. The selection of interaction partners is called team formation. Three basic approaches can be considered to match multi-agent system resources to the problem at hand. To research the properties of different approaches, a software for modeling team formation in multi-agent systems has been created and is presented...
-
New Applications of Multimodal Human-Computer Interfaces
PublikacjaMultimodal computer interfaces and examples of their applications to education software and for the disabled people are presented. The proposed interfaces include the interactive electronic whiteboard based on video image analysis, application for controlling computers with gestures and the audio interface for speech stretching for hearing impaired and stuttering people. Application of the eye-gaze tracking system to awareness...
-
Method of sacrificial anode transistor-driving in cathodic protection system
PublikacjaA magnesium anode driving system has been proposed. A PNP driving transistor has been used. Electrochemical testing in 3%NaCl, results and comparison of the driving system and classic direct anode to cathode connection are presented. The driving system reduced the protection current and stabilized the working conditions of the anode. Higher anode efficiency was achieved. Overprotection and hydrogen embrittlement threats were prevented...
-
Weldability of S460ML High Strength Low Alloy Steel in Underwater Conditions
PublikacjaThe paper presents experimental evaluation of susceptibility of the high strength S460ML steel to cold cracking in the conditions of wet welding with the use of covered electrodes. From the results of Tekken tests it was found out that the investigated steel was characterised, in the conditions of the carried out experiments (underwater wet welding and air welding with rutile electrodes), of high susceptibility to cold cracking....
-
Harmony Search to Self-Configuration of Fault-Tolerant Grids for Big Data
PublikacjaIn this paper, harmony search algorithms have been proposed to self-configuration of fault-tolerant grids for big data processing. Some tasks related to big data processing have been considered. Moreover, two criteria have been applied to evaluate quality of grids. The first criterion is a probability that all tasks meet their deadlines and the second one is grid reliability. Furthermore, some intelligent agents based on harmony...