Filtry
wszystkich: 2947
wybranych: 2190
-
Katalog
- Publikacje 2190 wyników po odfiltrowaniu
- Konferencje 1 wyników po odfiltrowaniu
- Osoby 113 wyników po odfiltrowaniu
- Wynalazki 2 wyników po odfiltrowaniu
- Projekty 7 wyników po odfiltrowaniu
- Kursy Online 80 wyników po odfiltrowaniu
- Wydarzenia 7 wyników po odfiltrowaniu
- Dane Badawcze 547 wyników po odfiltrowaniu
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: START/STOP TESTS
-
Influence of low-temperature physical hardening on stiffness and tensile strength of asphalt concrete and stone mastic asphalt
PublikacjaThis paper presents laboratory testing of stiffness modulus and indirect tensile strength of three asphalt concrete (AC) and three stone mastic asphalt (SMA) mixes after isothermal storage at temperature of -20oC, at different time intervals up to 16 days. The tests under repeated dynamic loading showed physical hardening of all tested mixes which was manifested by an evident increase of their stiffness moduli after isothermal...
-
Optical flow method for measuring deformation of soil specimen subjected to torsional shearing
PublikacjaIn this study optical flow method was used for soil small deformation measurement in laboratory tests. The main objective was to observe how the deformation distributes along the whole height of cylindrical soil specimen subjected to torsional shearing (TS test). The experiments were conducted on dry non-cohesive soil specimens under two values of isotropic pressure. Specimens were loaded with low-amplitude cyclic torque to analyze...
-
Effectiveness of a dual surface modification of metallic interconnects for application in energy conversion devices
PublikacjaA dual surface modification of an SOFC metallic interconnect with a Gd2O3 layer and an MnCo2O4 coating was evaluated. The tested samples were oxidized for 7000 h in air at 1073 K. Oxidation products were characterized using XRD, SEM-EDS, and confocal Raman imaging, and ASR was measured. The effect of gadolinium segregation at grain boundaries in Cr2O3 was evaluated using S/TEM-EDS. Area specific-resistance was measured and fuel...
-
Friction-Induced Oscillations of a Non-Asbestos Organic Pin Sliding on a Steel Disc
PublikacjaFriction-induced oscillations result in deterioration of performance of disc brakes and are generally undesired. We conduct experimental study of friction-induced oscillations in a non-asbestos organic material / steel pair used in disc brakes of motor vehicles. The tests are done by use of a pin-on-disc machine which has the pin sample supported on a deformable beam. The adjustable friction parameters are the disc velocity, contact...
-
The effects of vehicle restraint systems on road safety
PublikacjaKey to understanding the needs and tools of road infrastructure management for preventing run-off-road crashes or minimising their consequences, is to identify the hazads and sources of hazards caused by wrong or improper use of road safety devices and identify errors in the desifn, structure, construction and operation of road safety devices. Studying such an extended scope of the problem required fieldwork and surveys with road...
-
STABILITY AND LOAD BEARING CAPACITY OF A BARS WITH BUILT UP CROSS SECTION AND ELASTIC SUPPORTS
PublikacjaThe present paper is devoted to the numerical analysis and experimental tests of compressed bars with built–up cross section which are commonly used as a top chord of the roof trusses. The significant impact on carrying capacity for that kind of elements in case of out-of-plane buckling is appropriate choice of battens which are used to provide interaction between separate members. Linear buckling analysis results and nonlinear static...
-
SUBJECTIVE PERCEPTION OF MUSIC GENRES IN THE FIELD OF MUSIC INFORMATION RETRIEVAL SYSTEMS
PublikacjaThe aim of this paper is to evaluate the relationship between perception of music genres and subjective features of music that can be assigned to them. For this purpose a group of subjective features such as loudness, melody, rhythm, volume, instrumentation was chosen to describe music genres. A group of 30 listeners with normal hearing, ranging from 20 to 40, was created. Each sub-ject participating in listening tests was asked...
-
Damage detection in a bolted lap joint using guided waves
PublikacjaThe paper presents the experimental investigation of guided waves application to the condition assessment of prestressed bolted connections and a concept of new quantitative indicator. The main goal of the research was the analysis of the influence of the contact conditions changes to the characteristics of a propagating disturbance. The experimental tests were carried out for a single bolted lap joint. The excitation and acquisition...
-
Accelerated large scale test set-up design in natural corrosion marine environment
PublikacjaThe standards for conducting small-scale specimen tests are well developed, but there is a lack of direct guidelines for conducting corrosion tests for large-scale specimens. The objective here is to develop a methodology which may be used in designing an accelerated corrosion test of large-scale structural components subjected to a natural corrosion marine environment. Different factors influencing corrosion degradation of steel...
-
Nondestructive corrosion degradation assessment based on asymmetry of guided wave propagation field
PublikacjaThe article presents the results of numerical and experimental investigation of guided wave propagation in steel plates subjected to corrosion degradation. The development of novel procedures allowing for the assessment of the corrosion degradation level is crucial in the effective diagnostics of offshore and ship structures that are especially subjected to aggressive environments. The study’s main aim is to investigate the influence...
-
Biological and antibacterial properties of chitosan-based coatings with AgNPs and CuNPs obtained on oxidized Ti13Zr13Nb titanium alloy
PublikacjaDespite numerous studies, the antibacterial efficiency and cytotoxicity of chitosan-based coatings with nanometals need further studies. The purpose of this research was to determine the biological properties of chitosan coatings implemented with either silver nanoparticles (AgNPs) or copper nanoparticles (CuNPs), that were electrophoretically deposited on electrochemically oxidized Ti13Zr13Nb alloy. The SEM tests were used to...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublikacjaThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
Influence of Added Water Mass on Ship Structure Vibration Parameters in Virtual and Real Conditions
PublikacjaModelling of ship structures in a virtual environment is now standard practice. Unfortunately, many engineers forget to consideri the influence of added water on the frequency values and the amplitude of natural vibrations. The article presents the effect of water damping on the frequency values of the individual natural vibration modes. The tests were carried out in two stages. First, the mentioned values were determined using...
-
Possibilities of using SVC compensators for synchronous generators rotors oscillations damping.
PublikacjaThe article presents the idea of using static var compensators (SVC) for damping generators rotors oscillations. A novel SVC controller structure is proposed to provide better dynamic performance of the power system. A tests results are shown for proposed controller structure, that was carried out in a three-machine power system model as well as in multi-machine model of Polish Power System.
-
Main Outlines of Lightning Research Development in Poland
PublikacjaThe paper deals with the historical development of lightning protection research, lightning protection ideas and investigations in Poland. The main achievements of lightning research performed at the technical universities in Gdansk, Warsaw and Rzeszow have been characterized. Exemplary main achievements related to natural lightning observations and measurements as well to those performed in laboratory scale tests have been shortly...
-
Active feedback noise control in the presence of impulsive disturbances
PublikacjaThe problem of active feedback control of a narrowband acoustic noise in the presence of impulsive disturbances is considered. It is shown that, when integrated with appropriately designed outlier detector, the proposed earlier feedback control algorithm called SONIC is capable of isolating and rejecting noise pulses. According to our tests this guarantees stable and reliable operation of the closed-loop noise cancelling...
-
Wideband Radio Direction Finder Implemented in Software Defined Radio Technology
PublikacjaIn the paper a wideband radio direction finder (RDF) implemented in software defined radio (SDR) technology and the results of hardware layer research, including developed antenna switching unit (ASU), are presented. The results of tests of the devices, which are the part of the software defined radio platform (SDRP), and antenna switching unit, confirmed the possibility of using selected components in the final solution.
-
The analysis of soil resistance during screw displacement pile installation
PublikacjaThe analysis of soil resistances during screw displacement pile installation based on model and field tests. The investigations were carried out as a part of research project, financed by the Polish Ministry of Science and Higher Education. A proposal of empirical method for prediction of rotation resistance (torque) during screw auger penetration in non-cohesive subsoil based on CPT result.
-
Comparison of induction motor bearing diagnostic test results through vibration and stator current measurement
PublikacjaThe paper discusses results of tests performed by authors, related to the angine bearings diagnostic using vibration and stator current measurements. The paper contains the description of an automatic measurement system, developed for measurement of those harmonics and processing that to obtain bearing diagnostic information. System was tested on objects with intentionally made defects in bearings, results of this test was also...
-
Practical aspects of design and operation of amphibious craft for rescue purposes
PublikacjaThe paper presents the selected problems of design and operation of amphibious craft for rescue purposes. The result of research on the amphibious rescue units allowed formulating the general conclusions with respect to the proper selection of the main design parameters, program of model tests and full scale trials for the amphibious craft. The most important design problems related to the water characteristics are presents and...
-
UHF ESPAR antenna for simple Angle of Arrival estimation in UHF RFID applications
PublikacjaAn electronically switched beam antenna for localization of passive UHF RFID tags based on a simple Angle of Arrival (AoA) technique is proposed‥ Detailed antenna design and realization are presented together with corresponding simulations and measurement results. Experimental tests with passive UHF RFID tag show the validity of theoretical assumptions for application of the antenna in UHF RFID based localization systems.
-
Simulations of Shear Zones and Cracks in Engineering Materials Using eXtended Finite Element Method
PublikacjaNumerical simulations of cracks and shear zones in quasi-brittle materials are presented. Extended Finite Element Method is used to describe both cracks and shear zones. In a description of tensile cracks, a Rankine criterion is assumed. A discrete Mohr-Coulomb law is adopted for simulations of shear zones. Results of simple numerical tests: unixial tension, bending and biaxial compression are demonstrated.
-
Wybrane zagadnienia optymalizacji organizacji ruchu kolejowego w celu minimalizacji kosztów energii elektrycznej
PublikacjaW artykule przedstawiono podział kosztów w transporcie kolejowym z uwzględnieniem kosztów wewnętrznych przedsiębiorstwa, do których zaliczają się między innymi koszty dostępu do infrastruktury, czy koszty energii. Stwierdzono, że przy odpowiedniej organizacji ruchu pociągów na sieci kolejowej, bez ponoszenia dodatkowych nakładów na infrastrukturę i specjalistyczne urządzenia, można znacznie ograniczyć zużycie energii, a co za tym...
-
Analiza numeryczna wpływu długości zakotwienia pręta na zachowanie przyczepności w teście pull-out
PublikacjaW artykule przedstawiono symulacje numeryczne testu pull-out w programie ABAQUS. Symulacje miały na celu ocenienie wpływu długości zakotwienia pręta żebrowanego na przyczepność w tym teście, opierając się na wynikach przeprowadzonych eksperymentów. Interakcję pręta z betonem odwzorowano za pomocą kohezyjnej powierzchni kontaktu, wykorzystując skalibrowane krzywe przyczepność-poślizg, otrzymane z doświadczeń wykonanych w ramach...
-
Portable raman spectrometer with two excitation wavelengths
PublikacjaSelected problems of development of a portable Raman spectrometer having small size, reduced power consumption and robust construction are shown. The device dedicated for semiskilled personnel uses two lasers: 785nm and 355nm. Results of preliminary tests are presented. Also data processing procedures as well as problems referred to Raman signals acquisition through packages and influence of interfering signals are discussed.
-
Compact satellite hydraulic unit
PublikacjaThe article describes the design and operation of a prototype hydraulic unit. It is based on an inversed kinematics, satellite pump in which the body rotates around the shaft. The pump is placed inside the electric motor. Thanks to that the compact and low mass construction was achieved. Thanks to new commutation unit with enlarged channels, lower pressure losses were obtained. The article presents the construction and results...
-
THE INFLUENCE OF PHASE SHIFTERS ON THE VOLTAGE STABILITY OF CONNECTED POWER SYSTEMS
PublikacjaThe paper presents the results of simulation tests of connected power systems in which phase shifters were installed on cross-border links. The analysis was carried out in terms of assessing the impact of shifters on node voltage stability. Individual systems were characterized by different balance of active power: deficit or excess. The evaluation of voltage stability was based on the dU/dQ and dU/dP criteria.
-
Wear of Ultra-thin DLC or Tungsten-modified DLC Coatings under Reciprocating Sliding
PublikacjaIn the paper results are presented from tests in reciprocating sliding of self mated specimens of DLC and tungsten modified DLC coatings on stainless steel substrate. The contact geometry chosen for the research task was ball on flat. The contacts were lubricated either with distilled water or medical saline solution. Results are presented with regard to wear resistance as a function of material type and lubricant used.
-
Multifunctional PID Neuro-Controller for Synchronous Generator
PublikacjaThis paper deals with a PID Neuro-Controller (PIDNC) for synchronous generator system. The controller is based on artificial neural network and adaptive control strategy. It ensures two functions: maintaining the generator voltage at its desired value and damping electromechanical oscillations. The performance of the proposed controller is evaluated on the basis of simulation tests. A comparative study of the results obtained with...
-
Non-intrusive infrared-free eye tracking method
PublikacjaIn the paper a technique of eye tracking based on visible light is presented. The approach described does not require an additional hardware equipment used in the infrared eye tracking system. First, examples of existing eye tracking techniques were presented. Then, the proposed algorithm of image processing and the process of determining the eye position are described. The engineered eye tracking application was tested and the...
-
Gesture recognition framework for multimedia content viewer controlling
PublikacjaIn the paper a system for controlling a multimedia content viewer by hand gestures is presented. First, selected methods used for gesture recognition are described. Two different application cases of the system, i.e. for multimedia presentation purposes and for multimedia content viewing are outlined. Moreover, a proposal of improvement of the system combining these approaches is also given. The system work cycle is reviewed. The...
-
Effect of Soft Handover on the Capacity of WCMDA/FDD Interfece Using MRC RAKE Receiver in Uplink
PublikacjaIn the paper the mechanism of soft and hard hanover in UMTS is presented. Simulation tests for different services having various performance requirements and transmission rates have beeen made. Simulation results showing effect of soft handover in comparison with hard handover on the capacity of WCMDA/FDD radio interfaceare described, when the RAKE receiver with Maximal Ratio Combining has been implemented in RNC.
-
The aluminium and polycarbonate covering to the roof over the stadium in Gdańsk
PublikacjaThis paper presents information about structural elements of the roof covering to the stadium in Gdansk built for the 2012 European Football Championship in Poland and the Ukraine. The paper discusses elements of the polycarbonate covering, the supporting structure and the drainage system. It also provides information about tests and research performed prior to construction, which determined the solutions adopted as well as...
-
Spectroscopic wireless sensor of hematocrit level
PublikacjaAn optical method for hematocrit measurement is presented. The sensor, designed and developed by authors, consists of a spectroscopic set-up and a microcontroller. The work of the sensor is based on measurement of intensity of two selected spectral bands. Tests confirmed the ability of the sensor to determine the hematocrit level with appropriate measurement accuracy. Measurement results can be transmitted via wireless module to...
-
Smart Virtual Bass Synthesis Algorithm Based on Music Genre Classification
PublikacjaThe aim of this paper is to present a novel approach to the Virtual Bass Synthesis (VBS) algorithms applied to portable computers. The proposed algorithm employed automatic music genre recognition to determine the optimum parameters for the synthesis of additional frequencies. The synthesis was carried out using the non-linear device (NLD) and phase vocoder (PV) methods depending on the music excerpt genre. Classification of musical...
-
An Application Supporting Gastroesophageal Multichannel Intraluminal Impedance-pH Analysis
PublikacjaDue to a significant rise in the number of patients diagnosed with diseases of the upper gastrointestinal tract and the high cost of treatment, there is a need to further research on one of the most popular diagnostic tests used in this case – esophageal Multichannel Intraluminal Impedance and pH measurement. This may lead to finding new diagnostically relevant information, used to quicken and improve the diagnostic procedure....
-
Modified Manganese Phosphate Conversion Coating on Low-Carbon Steel
PublikacjaConversion coatings are one of the primary types of galvanic coatings used to protect steel structures against corrosion. They are created through chemical reactions between the metal surface and the environment of the phosphating. This paper investigates the impact that the addition of new metal cations to the phosphating reaction environment has on the quality of the final coating. So far, standard phosphate coatings have contained...
-
Evaluating the influence of radiative heat flux on convective heat transfer from a vertical plate in air using an improved heating plate
PublikacjaThis article examines the influence of radiative heat flux on the accuracy of the results of free convective heat transfer in air. In order to carry out these tests, based on the experience gained during the operation of a plate heated on one side, compensated by a reverse heat loss flux counter-heater, a unique double-sided heating sandwich plate was designed and built, consisting of three thin epoxy resin plates reinforced with...
-
Determination of Thermophysical Parameters Involved in The Numerical Model to Predict the Temperature Field of Cast-In-Place Concrete Bridge Deck
PublikacjaThe paper dealswith a concept of a practical computationmethod to simulate the temperature distribution in an extradosed bridge deck. The main goal of the study is to develop a feasible model of hardening of concrete consistent with in-situ measurement capabilities. The presented investigations include laboratory tests of high performance concrete, measurements of temperature evolution in the bridge deck and above all, numerical...
-
Regeneration of marine engine valves using laser surfacing
PublikacjaThis article presents an analysis of the applicability of laser surfacing of the exhaust valve face of a marine diesel engine using cobalt-based powder. After preparation by machining, the selected valves were subjected to laser surfacing using a high-power ROFIN DL020 laser. The EuTroLoy 16012 powder was used in the surfacing process. One of the valves was cut and subjected to metallographic examination and hardness measurements,...
-
Static Load Test on Instrumented Pile – Field Data and Numerical Simulations
PublikacjaFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Evaluation of a Novel Approach to Virtual Bass Synthesis Strategy
PublikacjaThe aim of this paper is to present a novel approach to the Virtual Bass Synthesis (VBS) strategy applied to portable computers. The developed algorithms involve intelligent, rule-based settings of bass synthesis parameters with regard to music genre of an audio excerpt and the type of a portable device in use. The Smart VBS algorithm performs the synthesis based on a nonlinear device (NLD) with artificial controlling synthesis...
-
Application of chemometric techniques in studies of toxicity of selected commercially available products for infants and children
PublikacjaThe goal of the present study is to assess the impact of the experimental conditions for extraction procedures (time of extraction, thermal treatment and type of extraction media) as applied to several baby and infant products checked for their possible ecotoxicological response when tested by various ecotoxicity tests(Microtox®, Ostracodtoxkit F™and Xenoscreen YES/YAS™). The systems under consideration are multidimensional by...
-
Static load test on concrete pile – instrumentation and results interpretation
PublikacjaFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Effect of interlayer bonding quality of asphalt layers on pavement performance
PublikacjaThe quality of interlayer bonding at the interfaces between the asphalt layers in flexible pavements affects the overall pavement performance. Lack or partial lack of interlayer bonding between asphalt layers can cause pavement's premature failures such as rutting, slippage of the wearing course, cracking or simply a reduction in the calculated fatigue life of the pavement structure. This paper shows the case studies of investigation...
-
A Thermographic Measurement Approach to Assess Supercapacitor Electrical Performances
PublikacjaThis paper describes a proposal for the qualitative assessment of condition of supercapacitors based on the conducted thermographic measurements. The presented measurement stand was accompanied by the concept of methodology of performing tests. Necessary conditions, which were needed to minimize the influence of disturbing factors on the performance of thermal imaging measurements, were also indicated. Mentioned factors resulted...
-
Corrosion degradation of spacers – examination of changes in bone cement coating.
PublikacjaSpacer is a special implant used at the time of infection after endoprosthetic surgery. It consists of a metal core and bone cement coating with an antibiotic. In the human body spacers are exposed to degradation processes. This paper looks at the effect of corrosion on spacers. Electrochemical corrosion tests were performer on titanium pins with bone cement coating in two solutions: Ringer’s solution and artificial...
-
Production of six-degrees-of-freedom (6DoF) navigable audio using 30 Ambisonic microphones
PublikacjaThis paper describes a method for planning, recording, and post-production of six-degrees-of-freedom audio recorded with multiple 3rd order Ambisonic microphone arrays. The description is based on the example of recordings conducted in August 2020 with the Poznan Philharmonic Orchestra using 30 units of Zylia ZM-1S. A convenient way to prepare and organize such a big project is proposed – this involves details of stage planning,...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATION ON SPECIMEN GEOMETRY EFFECT ON THE CTOD VALUE FOR VL-E36 SHIPBUILDING STEEL
PublikacjaThere are special cases in the marine industry, where additional material tests, such as the fracture toughness test, must be performed. Additional fracture toughness tests, such as CTOD (Crack Tip Opening Displacement), are typically performed on three-point bend specimens. The dimension that defines all the specimen dimensions is the thickness of the material to be tested. It is recommended by classification societies (e.g. DNVGL)...
-
Analysis of Failure Mechanism in Joints with Positive Eccentricity in CFS Truss
PublikacjaThe paper presents studies concerning the load-bearing capacity of truss joints with a positive eccentricity resulting from the arrangement of geometric members and the failure mechanisms observed in the joints. Based on the previously conducted experimental study, a numerical model of the tested fragment of the CFS truss with eccentricity in the joint was created and validated. All structural details of the tested truss and the...