Filtry
wszystkich: 1494
wybranych: 1170
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: RECYCLED STEEL FIBRES
-
Influence of permanent magnetic field on wear performance of dry sliding contacts
PublikacjaResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact are presented.It was found that magnetic field of horizontal orientation is causing temporary reduction of material's hardness. It also facilitates and accelerates removal process of wear particles from the contact zone.Formation of bulges, consisting of accumulated and compacted anti-ferromagnetic material produced...
-
Jumping Wave Characteristic during Low Plasticity Burnishing Process
PublikacjaDuring the low plasticity burnishing process of soft materials such as carbon steel with a hardness of up to 40 HRC (Rockwell grade) a raised structure of the material known as the Jumping Wave forms in front of the tool roll. This phenomenon significantly disturbs the burnishing process, but is very poorly described in the literature. This article presents studies of this phenomenon on the example of burnished 1.0562 steel. The...
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublikacjaOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Guided ultrasonic waves for detection of debonding in bars partially embedded in grout
PublikacjaThis paper deals with theoretical, numerical and experimental investigations of guided wave propagation in multilayered cylindrical bars with pre-existing debonding. The research focuses on a complex description of the nature of the wave phenomena occurring in a debonded specimen with a special emphasis on the influence of the location of damage on the wave conversion and diffraction. Experimental non-destructive and destructive...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
Opracowanie ekspertyzy dotyczącej przyczyn pękania łopatek wirnika SP turbiny PG1 typu 13UP55
PublikacjaZakres badań i analiz dotyczył ustalenia przyczyn pękania elementów łopatek wirnika SPA5 turbiny TG1 typu 13UP55 obejmował: 1. wykonanie badań składu chemicznego stali, z której wykonano łopatki dostarczone przez Zleceniodawcę dwoma metodami, 2. badania mikroobszarów zniszczenia łopatek na mikroskopie elektronowym skaningowym z mikroanalizatorem EDS, 3. badania metalograficzne makroskopowe i mikroskopowe fragmentów...
-
Hydrogen Damage in Superaustenitic 904L Stainless Steels
Publikacjaresults on the influence of hydrogen on corrosion resistance and of hydrogen embrittlement of 904L superaustenitic stainless steel were investigated. The cracking behavior was studied by performing a slow strain rate test in synthetic seawater under varying cathodic polarization conditions. The results showed that the steel’s plasticity varied with the applied cathodic current density. Significant reductions in ductility were found,...
-
Dissimilar underwater wet welding of HSLA steels
PublikacjaThe high-strength low-alloy S460ML and S460N steels were chosen for underwater wet welding of dissimilar T-joints using covered electrodes. For improving the quality of joints, the temper bead welding (TBW) method was used. The application of TBW in pad welding conditions has been investigated earlier but the possibility of usage of this technique in welded joints was not analyzed. The main aim of the study was to check the influence...
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublikacjaExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
Storing Matter’technique in SIMS depth profile analysis
PublikacjaSecondary ion mass spectrometry (SIMS) is a very useful technique for the analysis of layered systems. It is based on the primary ion beam sputtering of solids and mass analysis of the emitted secondary ions. A main limitation of this technique results from the direct quantitative analysis, since the ionization efficiency of a given atom is highly influenced by the neighbouring atoms at the surface. This phenomenon is known as...
-
Polyurethane-wood composites (PU-WC) as a method of wood waste management
PublikacjaIn recent years, due to the progressive environmental degradation and increase of environmental awareness, the sustainability of production systems in wood processing, the wood industry, and wood waste management is a crucial issue for European industry and society. Consequently, the problem of generating wood-like waste and the associated risks has become an increasingly noticeable challenge for science. Although various methods...
-
Report no: WOiO /II/46/2015 - Construction node verification test, estimation of breaking load (shear force) and destruction form
PublikacjaA new generation of tanks for LNG transportation has been designed. Mass reduction forced our customer to use three different materials: austenitic steel, aluminium alloy and LNG compressed wood between them. The expertise concerns structural node between tank foundation and suspension. Expertise contains: description of object of test, test principals, results and conclusions
-
Wpływ rodzaju zanieczyszczenia powierzchni odlewu ze staliwa LH14 na jakość napoin wykonanych elektrodą otuloną
PublikacjaNapawanie jest szeroko stosowaną metodą naprawiania powierzchni. Pozwala między innymi na uzupełnienie miejsc, w których uprzednio wystąpiły wżery korozyjne. Techniki napawania wykorzystywane są również do przywracania pierwotnego kształtu zużytych części. W pracy wykonano badania napoin wykonanych elektrodami otulonymi na czołowych powierzchniach cylindrycznych próbek ze staliwa LH14. Proces wykonywano dwoma rodzajami elektrod:...
-
Analisys of the failure of fixator used in bone surgery
PublikacjaThe Gamma nail (fixator) made of stainless steel, which has broken in the body, was subjected to examination. The fixator was removed from the patient femur. The fracture occurred in the area of the nail hole after two months' stay in the organism. The research included chemical composition, hardness of the Gamma nail material and the observation and analysis of the type of fracture. The research showed the fatigue failure of the...
-
Wear of Ultra-thin DLC or Tungsten-modified DLC Coatings under Reciprocating Sliding
PublikacjaIn the paper results are presented from tests in reciprocating sliding of self mated specimens of DLC and tungsten modified DLC coatings on stainless steel substrate. The contact geometry chosen for the research task was ball on flat. The contacts were lubricated either with distilled water or medical saline solution. Results are presented with regard to wear resistance as a function of material type and lubricant used.
-
Evaluation of cathode materials for electrochemical photocatalyst deposition
PublikacjaElectrochemical deposition of photocatalyst, especially TiO2, onto several cathode materials was investigated and evaluated. The deposited films were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDX) and electrochemical measurements. Photocatalytic activity was determined by the decomposition of cyclohexane in air by irradiation with ultraviolet light emitting diodes. It was found that...
-
Integrated production technology of cylindrical surfaces by turning and burnishing
PublikacjaThe method is based on a combination of previously used two separate operations namely machining and burnishing in a one complex operation implemented on a lathe.In the case of machining shafts and hydraulic cylinders of steel C45 is possible to obtain a surface roughness Ra=0,16 - 0,32 micrometers, dimensional accuracy class 7-8 according to ISO standards, and increase in the hardness of the surface up to 40%.
-
The reasons of considarable deflections of roof trusses in engineering analysis
PublikacjaThe aim of the paper is to present an unconventional analysis of deformations of roof trusses of an exhibition pavilion. Structure of the main hall of the pavilion consists of repeatable span frames with steel pillars made of I-sections, fastened in the foundations and hinged supporting roof girders. The roof trusses, completed in steel construction, have undergone considerable permanent deflections. Deformations of the lower chord...
-
Badania eksperymentalne strefy przypodporowej żelbetowych belek częściowo sprężonych
PublikacjaThis project refers to the study the shear zone, under full and partial prestressing in comparison to beams with passive reinforcement.For comparison, variable parameters have been determined:- a/d (from 1,5 to 3,5) - it's shear span to effective depth of the beam . Assuming constant geometrical quantities, "a" is variable.- 26 beams had no vertical shear reinforcement, and the other 26 had closed stirrups.- prestressing intensity...
-
Analysis of Failure Mechanism in Joints with Positive Eccentricity in CFS Truss
PublikacjaThe paper presents studies concerning the load-bearing capacity of truss joints with a positive eccentricity resulting from the arrangement of geometric members and the failure mechanisms observed in the joints. Based on the previously conducted experimental study, a numerical model of the tested fragment of the CFS truss with eccentricity in the joint was created and validated. All structural details of the tested truss and the...
-
RESEARCH ON ORGANIC COATINGS DESIGNED FOR UNDERWATER APPLICATIONS
PublikacjaUnderwater steel structures require periodic maintenance. In the case of vessels, anti-corrosion works are carried out in the shipyard, where very good conditions for applying organic protective coatings can be provided. Very good surface preparation can be obtained by the use of abrasive blasting. The well-prepared metal surface is free from impurities (particularly inorganic salts). Suitable conditions for the application and...
-
Wstępne badania technologii spawania złączy narożnych ze stali niskoweglowej i nierdzewnej o grubości g=6mm i g=10mm
PublikacjaCelem pracy był dobór parametrów spawania dla spoin narożnych o grubości 6mm i 10mm próbek wykonanych ze stali niskowęglowej S355 i stali nierdzewnej - typu 304 (X6CrNI18-10). Złącza były spawane laserowo, jednostronnie z pełnym przetopem a powierzchnie lica i grani zapewniają uzyskanie szczelności przylegającego elementu uszczelniającego. Próbki zostały dostarczone przez Zleceniodawcę. Próby zostały przeprowadzone na stanowisku...
-
Effect of long term service at elevated temperatures on mechanical properties of Manaurite XM reformer tubes
PublikacjaMicrostructure transformations occur in the Manaurite XM cast steel tubes during long-term operation in the reformer furnace were revealed and described. The rela tionship between mechanical properties, an increase of internal diameter of the tube and microstructure degradation is discussed. Static tensile test was performed on two types of samples with different shapes. It has been shown differences in the results of tests...
-
A new strategy for PET depolymerization: Application of bimetallic MOF-74 as a selective catalyst
PublikacjaLarge-volume production of poly(ethylene terephthalate) (PET), especially in the form of bottles and food packaging containers, causes problems with polymer waste management. Waste PET could be recycled thermally, mechanically or chemically and the last method allows to obtain individual monomers, but most often it is carried out in the presence of homogeneous catalysts, that are difficult to separate and reuse. In view of this,...
-
Towards understanding the role of peroxide initiators on compatibilization efficiency of thermoplastic elastomers highly filled with reclaimed GTR
PublikacjaThermoplastic elastomers based on recycled high density polyethylene (rHDPE) and styrene-butadiene-styrene (SBS) block copolymer were highly filled with reclaimed ground tire rubber (RR). The impact of various organic peroxides (dicumyl peroxide (DCP), benzoyl peroxide (BP) and di-tert-butyl peroxide (DB)), applied as free-radical initiators, on the processing, structure and performance properties of rHDPE/SBS/RR blends was investigated....
-
Trwałość spawanych instalacji wodnych wykonanych z nierdzewnych stali austenitycznych
PublikacjaW artykule przedstawiono dwa przypadki przedwczesnych uszkodzeń spawanych instalacji wodnych wykonanych ze stali odpornych na korozję. W celu ustalenia przyczyn uszkodzenia instalacji przeprowadzono badania metalograficzne, makro - i mikroskopowe oraz mikroanalizę składu chemicznego EDS na próbkach pobranych z reprezentatywnych miejsc. Wykazano, że głównymi przyczynami awarii rurociągów wody pitnej były niezgodności spawalnicze,...
-
Membrane-SPME the best 'green' sample preparation technique for the gas chromatographic determination polar organic pollutants in polar media
PublikacjaOne of the most popular technique for sample preparation, which fulfill requirements of green analytical chemistry, is solid phase microextraction (SPME). Because of the undoubted advantages of SPME technique, solvent-free character of the extraction process and the enormous potential in analytical practice, a series of studies has been undertaken to develop new technical solutions, where improving the sensitivity and the extraction...
-
Development of novel optoelectronic sensory structures utilising colour centres in nanodiamonds and their interactions with analytes
PublikacjaThe goal of this dissertation was to develop and assess surface modifications of fluorescent nanodiamonds (NDs) for optical sensing. Three modification routes were tested, each aimed at a different application. Modification with poly-L-lysine (pLys) was verified for optical sensing of pH via an interrelationship between electrically negative (NV¯) and neutral (NV0) nitrogen-vacancy centres. Immobilisation of Ochratoxin A (OTA),...
-
The Characteristic of Surface Layers on Austenitic Stainless SteelAfter Glow-discharge Nitriding Process.
PublikacjaThis paper presents investigation of surface layers. The diffusion layers were produced by using different parameters of reactive atmosphere (N2:H2). The research of the surface layers was performed using scanning electron microscope (SEM). The results of energy dispersive X-ray (EDX) analysis and X-ray diffraction (XRD) analysis are presented. Research reveals the influence of chemical constitution of reactive atmosphere on the...
-
Effect of water salinity on properties of multipass underwater wet manual metal arc welded joints
PublikacjaThe weldability of steel under the water is limited due to the influence of the environment. Water causes limited visibility, presence of the residual stresses, increasing the cooling rate, and increasing the diffusible hydrogen content in deposited metal, leading to the formation of brittle microstructures in heat-affected zone (HAZ). The paper presents the results of mechanical properties testing of S420G2+M steel welded joints...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublikacjaThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
Morphology changes in Fe-Cr porous alloys upon high-temperature oxidation quantified by X-ray tomographic microscopy
PublikacjaThe effect of high-temperature oxidation at 850 C (10 h, 30 h, 100 h) and 900 C (10 h) on porous (30 % porosity) ferritic stainless steel (Fe22Cr) has been investigated using synchrotron tomographic microscopy, which allowed for visualisation, separation and quantitative analysis of the metallic core, closed pores, open pores and oxide scale phase. The same regions within the samples were investigated before and after oxidation...
-
Actual field corrosion rate of offshore structures in the Baltic Sea along depth profile from water surface to sea bed
PublikacjaThe paper presents the results of field electrochemical investigations on the corrosion rate of carbon steel in seawater of the Baltic Sea at the location of the Baltic Beta production rig. The measurements were conducted throughout the year in seawater at different depths from the sea surface to the sea bed (about 75 m). The results revealed corrosion aggressiveness of the seawater along the entire depth profile. There was...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublikacjaTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
Introducing a Computational Method to Retrofit Damaged Buildings under Seismic Mainshock-Aftershock Sequence
PublikacjaRetrofitting damaged buildings is a challenge for engineers, since commercial software does not have the ability to consider the local damages and deformed shape of a building resulting from the mainshock record of an earthquake before applying the aftershock record. In this research, a computational method for retrofitting of damaged buildings under seismic mainshock-aftershock sequences is proposed, and proposed computational...
-
Experimental tests of reinforced concrete deep-beams
PublikacjaThe paper presents results of experimental research of the reinforced concrete deep beam with a spatial arrangement. Tested structural elements consist of the cantilever deep beam loaded on the height and transverse deep beam with hanging on it another one. The analysis includes crack morphology, effort of steel and load distribution. The article verified effectiveness of two different kind of reinforcement in both tested deep...
-
The bridge over Regalia River in Szczecin - design and construction.
PublikacjaNowoclowa Route is the largest projekt in Szczecin, that consists of 11 km of roads 3,3 km bridges and viaducts, including three parallel bridges across Regalica River (the east arm of Odra River), 535 m long, with the spans: 59+90+90+116+116+64m. The bridge structure consist of two steel plate girders composite with reinforced concrete deck slab. The design and the construction of the bridge are described in the paper.
-
The Effect of Long Term Service at Elevated Temperatures on Microstructure Degradation of Austenitic Reformer Tubes
PublikacjaThe paper analyses the relationship between an increase of the inner diameter of tubes made of Manaurite XM cast steel and transformations occurring in their microstructure due to long-lasting operation in methane reformer. Examinations included metallographic analysis with light microscope (LM), scanning electron microscope (SEM) and microanalysis of the chemical composition of precipitates (EDX). It was indicated that there is...
-
Finite element simulation of cross shaped window panel supports
PublikacjaThe aim of the work is to verify suitability of cross-shaped window panel supports for mullion-transom wall systems. The Finite Element Method (FEM) is chosen to determine the behaviour of stainless steel elements under loading. The advanced non-linear numerical simulations are carried out using an implicit FEM software package MSC.Marc. This study is proposed to initiate the comprehensive investigation of mechanical properties...
-
A novel formulation of 3D spectral element for wave propagation in reinforced concrete
PublikacjaThe paper deals with numerical simulations of wave propagation in reinforced concrete for damage detection purposes. A novel formulation of a 3D spectral element was proposed. The reinforcement modelled as the truss spectral element was embedded in the 3D solid spectral finite element. Numerical simulations have been conducted on cuboid concrete specimens reinforced with two steel bars. Different degradation models were considered...
-
Eksperymentalne i numeryczne badania parametrów dynamicznych trybuny stalowej
PublikacjaTrybuny stalowe to konstrukcje, które odnajdują swoje zastosowanie głównie podczas wydarzeń sportowych, koncertów muzycznych oraz innych wydarzeń, którym towarzyszą rytmiczne aktywności widzów i głośna muzyka. Ze względu na smukłość oraz lekkość elementów z jakich wykonana jest konstrukcja trybuny jest ona bardzo łatwo wzbudzana przez ludzi do drgań. Z przeprowadzonej w pracy [4] analizy modalnej wynika, że masa ludzi prowadzi...
-
Design of Inner Gate for CRIST Shipyard Dry Dock
PublikacjaThe paper deals with a removable steel inner gate which was designed to separate two parts of a dry dock of about 70 m in width and 380 m in length. The gate allows for independent assembly of ship structures in two separated parts of the dock. The fore part of the dock can be flooded while the after part is dry. Tthe gate was designed by IDEK Company Ltd in 2011 and it was soon constructed and used by CRIST Shipyard in Gdynia.
-
Effect of elliptical defect orientation on the durability of specimens subjected to cyclic bending
PublikacjaThis work presents the effect of elliptical defects orientation on the durability of specimens made of C45 steel. Three kinds of specimens with elliptical defects in the form of a one-sided notch oriented at different angles 45, 60, and 90 degrees were subjected to cyclic bending (R=-1). The stress state analysis was performed using local and non-local methods to determine an equivalent amplitude of stress, and then the results...
-
Integrated dewatering and stabilization system as an environmentally friendly technology in sewage sludge management in Poland
PublikacjaSludge treatment reed beds (STRBs) are an environmentally friendly technology which provides integrated dewatering and stabilization of sewage sludge. STRBs do not require the use of chemicals to improve the dewatering process. STRB is both, a low-emission and a low-energy-consuming method. After the stabilization process, sludge is characterized by the chemical composition similar to that of humus. The aim of the paper is to present...
-
Evaluation and rationale of the performance of several elastomeric composites incorporating devulcanized EPDM
Publikacjathylene Propylene Diene rubber (EPDM), is present in many applications. However, its crosslinked structure makes difficult its recycling. The use of devulcanized EPDM, (dEPDM) as a component of elastomeric composites, is a real possibility to reuse EPDM scraps. In this study, three matrices (natural rubber (NR), styrene butadiene rubber (SBR) and EPDM rubber) have been tested including devulcanized EPDM as a recycled component....
-
Wpływ posuwu nagniatania na chropowatość powierzchni przedmiotów ze stali w stanie utwardzonym
PublikacjaPrzedstawiono wyniki badań eksperymentalnych procesu nagniatania stali twardej (62 HRC) narzędziem ceramicznym (kulką) z dociskiem hydrostatycznym. Analizowano wpływ posuwu nagniatania oraz parametrów poprzedzającej obróbki toczeniem na twardo na stan powierzchni opisanej wybranymi parametrami chropowatości.
-
Iron doped manganese cobaltite spinel coatings produced by electrophoretic co-deposition on interconnects for solid oxide cells: Microstructural and electrical characterization
PublikacjaWe report a systematic microstructural and electrical characterization of iron doped Mn–Co spinel coatings processed by electrophoretic co-deposition of Mn1.5Co1.5O4 and Fe2O3 powders on Crofer 22 APU and AISI 441 steel substrates. Iron addition to Mn–Co spinel coating leads to a reduction of the area specific resistance on both substrates, after 3200 h at 750 °C. The Fe doped Mn–Co coating both leads to a thinner oxide scale and...
-
Non-Linear Analysis of Inter-Story Pounding between Wood-Framed Buildings during Ground Motion
PublikacjaPounding between adjacent buildings during ground motion may result in structural damage or lead to total destruction of structures. The research on the phenomenon has recently been much advanced; however, the analyses have been carried out only for concrete, steel, and masonry structures, while pounding between wooden buildings has not been studied so far. The aim of this paper is to show the results of detailed non-linear seismic...
-
Comparison of strain results at a laser weld notch obtained by numerical calculations and experimental measurements
PublikacjaIn the development of ship structures applying new materials and it’s purposeful placement play an important role. During the last years, especially in a construction of ro-ro type vessels, the usage of novel sandwich structures in cargo decks is profitable. Steel sandwich panel is an innovative solution which at a todays state of development can be used for the construction of any members not taking part in a global bending of...
-
Corrosion process monitoring by AFM higher harmonic imaging
PublikacjaThe atomic force microscope (AFM) was invented in 1986 as an alternative to the scanning tunnelling microscope, which cannot be used in studies of non-conductive materials. Today the AFM is a powerful, versatile and fundamental tool for visualizing and studying the morphology of material surfaces. Moreover, additional information for some materials can be recovered by analysing the AFM's higher cantilever modes when the cantilever...