Filtry
wszystkich: 1688
wybranych: 1503
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TYPES
-
Usefulness of chest perfusion computed tomography in the diagnosis of diabetic pulmonary microangiopathy
PublikacjaThis paper presents the usefulness of perfusion computed tomography (pCT) in the diagnosis of diabetic pulmonary microangiopathy. Our previous works have shown that perfusion parameters are useful in the diagnosis of diabetic pulmonary microangiopathy. We are looking for such measurements and perfusion parameters that provide the most accurate diagnosis. Two types of comparison were made based on the results of clinical trials:...
-
„Eulerian – Eulerian” versus ,,Eulerian –Lagrangean” models of condensation
PublikacjaLiquid phase in the flowing vapor through stages of the steam turbine is the cause of a lot of failures. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current. The formation of drops of condensate under conditions other than nominal operation of turbine is a process still unknown. Engineers and designers involved in the development of power station machines...
-
Use of Neural Networks in Diagnostics of Rolling-Element Bearing of the Induction Motor
PublikacjaBearing defect is statistically the most frequent cause of an induction motor fault. The research described in the paper utilized the phenomenon of the current change in the induction motor with bearing defect. Methods based on the analysis of the supplying current are particularly useful when it is impossible to install diagnostic devices directly on the motor. The presented method of rolling-element bearing diagnostics used indirect...
-
Call Processing Performance in a Multidomain IMS/NGN with Asymmetric Traffic
PublikacjaIn this paper we continue our research using the previously proposed analytical traffic model of a multidomain Next Generation Network (NGN), which is standardized for delivering multimedia services based on the IP Multimedia Subsystem (IMS). The aim of the model is to assess mean Call Set-up Delay (CSD) and mean Call Disengagement Delay (CDD), which are standardized call processing performance parameters. The output variables...
-
Underwater Acoustic Imaging of the Sea
PublikacjaAcoustic waves are a carrier of information mainly in environments where the use of other types of waves, for example electromagnetic waves, is limited. The term acoustical imaging is widely used in the ultrasonic engineering to imaging areas in which the acoustic waves propagate. In particular, ultrasound is widely used in the visualization of human organs - ultrasonography (Nowicki, 2010). Expanding the concept, acoustical imaging...
-
Chronographic Imprint of Age-Induced Alterations in Heart Rate Dynamical Organization
PublikacjaBeat-to-beat changes in the heart period are transformed into a network of increments between subsequent RR-intervals, which enables graphical descriptions of short-term heart period variability. Three types of such descriptions are considered: (1) network graphs arising from a set of vertices and directed edges, (2) contour plots of adjacency matrices A, representing the networks and transition matrices T, resulting from A, and (3)...
-
Application of passive acoustic radar to automatic localization, tracking and classification of sound sources
PublikacjaA concept, practical realization and applications of the passive acoustic radar to automatic localization, tracking and classification of sound sources were presented in the paper. The device consists of a new kind of multichannel miniature sound intensity sensors and a group of digital signal processing algorithms. Contrary to active radars, it does not emit the scanning beam but after receiving surrounding sounds it provides...
-
Crack propoagation in MgO-PSZ ceramic materials
PublikacjaThe properties of ceramic materials such as elevated hardness, high temperature capability, low coefficient of thermal expansion are of interest for rolling element materials. Widely used ceramic materials in engineering applications are silicon nitride, zirconia and alumina. The paper presents an experimental study of the fatigue life of MgO-PSZ ceramic material in lubricated contact with defined types of cracks. A ceramic angular...
-
Analysis of MArkers of Exposure to Constituents of Environmental Tobacco Smoke (ETS)
PublikacjaTobacco smoke is a complex mixture of more than 4000 chemical compounds, many of which are harmful to human health. These compounds belong to various chemical classes, including amides, imides, lactams, carboxylic acids, aldehydes, ketones, alcohols, phenols, amines, hydrocarbons, ethers, and inorganic compounds. There are three types of tobacco smoke streams: the mainstream, the sidestream, and environmental tobacco smoke (ETS)....
-
Modal analysis of a steel grandstand
PublikacjaAmong the issues related to the idea of sustainable society is the safety of civil engineering structures devoted to satisfy different needs of people. One of the types of structures devoted to satisfy recreational needs are grandstands, which are used during sport events or music concerts. It is obligatory to consider interaction between structure and crowd load especially when the crowd movement involves rhythmic jumping, dancing,...
-
C2 NIWA Community-Segmentation Criteria and Building Brand Associations on the Example of a Selected Target Group
PublikacjaEvery organization which offers products or services wishes to communicate with their customers in the most effective way. This kind of communication is based on proper selection of target groups, which are extracted in the process of market segmentation. That is way it is very important to ask the question to whom the message is to be directed and what kind of message we want to give. This article describes the selection criteria...
-
Bass Enhancement Settings in Portable Devices Based on Music Genre Recognition
PublikacjaThe paper presents a novel approach to the Virtual Bass Synthesis (VBS) applied to mobile devices, called Smart VBS (SVBS). The proposed algorithm uses an intelligent, rule-based setting of bass synthesis parameters adjusted to the particular music genre. Harmonic generation is based on a nonlinear device (NLD) method with the intelligent controlling system adapting to the recognized music genre. To automatically classify music...
-
Exploring governance among social co-operatives: three models from Poland
PublikacjaThere has been overly interest regarding social enterprise and social entrepreneurship in theory and practice. In this paper the author introduces the workings of governance of small social enterprises i.e. social co-operatives, acting in most cases for the purpose of work and social integration of the marginalized, at the bottom of the pyramid of socio-economic system. The aim of this paper is to provide insights into under researched...
-
Modeling N2O behavior during denitrification with different carbon sources and electron acceptors
PublikacjaA mathematical model was developed for identification of the most important mechanism leading to nitrous oxide (N2O) accumulation in denitrifying activated sludge systems. The activated sludge model No. 2d (ASM2d) was extended to include intermediate three steps of the denitrification process. The formation and accumulation of nitric oxide (NO) was assumed to be very low in the performed laboratory experiments. These experiments...
-
Anharmonic Infrared Spectroscopy through the Fourier Transform of Time Correlation Function Formalism in ONETEP
PublikacjaDensity functional theory molecular dynamics (DFT-MD) provides an efficient framework for accurately computing several types of spectra. The major benefit of DFTMD approaches lies in the ability to naturally take into account the effects of temperature and anharmonicity, without having to introduce any ad hoc or a posteriori corrections. Consequently, computational spectroscopy based on DFT-MD approaches plays a pivotal role in...
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublikacjaOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
Determination of toxic gases based on the responses of a single electrocatalytic sensor and pattern recognition techniques
PublikacjaA response from an electrocatalytic gas sensor contains fingerprint information about the type of gas and its concentration. As a result, a single gas sensor can be used for the determination of different gases. However, information about the type of gas and its concentration is hidden in the unique shape of the current–voltage response and it is quite difficult to explore. One of the ways to get precise information about the measured...
-
Determination of total mercury in raw petrol using cold vapour atomic absorption spectrometry
PublikacjaPresence of different forms of mercury in petroleum based products may impair the proper operation of the equipment or led to poisoning of automotive catalysts. However much more important problem is environmental pollution with mercury emitted from different types of fossil fuels. Although the average mercury concentration in petroleum based products (automotive fuels) is on the level around 1 ppb, taking into account annual...
-
Analysis of Airport Runoff Waters
PublikacjaA particularly important facet of airport operation is the impact of the pollution caused byrunoff waters. Runoff waters at an airport may contain relatively high concentrations of differentcontaminants resulting from the various aspects of its operation: de/anti-icing operations,washing and cleaning operations, spills of fuel and lubricants, exhaust fumes, and weed removal.The pollution caused by airport operations affects soil,...
-
Synthesis of functionalized new conjugates of batracylin with tuftsin/ retro-tuftsin derivatives and their biological evaluation
PublikacjaNew batracylin conjugates with tuftsin/retro-tuftsin derivatives were designed and synthesized using T3P as a coupling agent. The conjugates possess an amide bond formed between the carboxyl group of heterocyclic molecule and the N-termini of the tuftsin/retro-tuftsin chain. The in vitro cytotoxic activity of the new analogues and their precursors was evaluated using a series of human and murine tumor cells. BAT conjugates containing...
-
Experimental investigation of Steel–Concrete–Polymer composite barrier for the ship internal tank construction
PublikacjaTransportation of dangerous cargo by ships demands ensuring an appropriate protection level in case of an accident. Two of the most dangerous accident types resulting in an oil spill are grounding and ship to ship collision. The article presents results of research on a new composite construction for a ship hull that increases structural safety during collision. The concept of semi-elastic Steel–Concrete–Polymer structure is presented....
-
Carbon Dioxide and Water Vapour Fluxes of a Alkaline Fen and Their Dependence on Reflectance
PublikacjaThis study shows results of parallel measurements of greenhouse gases fluxes (carbon dioxide and water vapour) and canopy reflectance of alkaline fen. Fluxes were measured using eddy-covariance technique on micrometeorological station located in the Upper Biebrza Basin (NE Poland) in Rogożynek Village. Study site is located in the Biebrza National Park which was established to protect one of the biggest coherent lowland wetland...
-
Proposed method for estimating the costs of safety barrier life cycle
PublikacjaToday barrier types are frequently selected for their price with little regard for the total costs the structure will incur over its lifetime. One of the basic tools designed to manage road infrastructure is the life cycle cost method (LCC, Life cycle cost). It sums up the costs to plan, design, build, operate (use and maintain) and decommission a road structure. Having developed dynamically at the turn of the century the method...
-
Integrated Photocatalytic Advanced Oxidation System (TiO2/UV/O3/H2O2) for Degradation of Volatile Organic Compounds
PublikacjaSeveral advanced oxidation processes (AOPs) including photocatalytic processes were studied for effective treatment of complex model wastewater containing a wide variety of VOCs. The studies revealed synergistic effects of TiO2 based processes for improved degradation of the VOCs. A peroxone combined with TiO2/UV system (TiO2/UV/O3/H2O2) with a ratio between the oxygen source from the oxidant to chemical oxygen demand (COD) of...
-
Comparative Evaluation of Selected Biological Methods for the Removal of Hydrophilic and Hydrophobic Odorous VOCs from Air
PublikacjaDue to increasingly stringent legal regulations as well as increasing social awareness, the removal of odorous volatile organic compounds (VOCs) from air is gaining importance. This paper presents the strategy to compare selected biological methods intended for the removal of different air pollutants, especially of odorous character. Biofiltration, biotrickling filtration and bioscrubbing technologies are evaluated in terms of...
-
Drop-coating deposition surface-enhanced Raman spectroscopy on silver substrates for biofluid analysis
PublikacjaUtilization of surface-enhanced Raman spectroscopy as a measurement technique is of particular interest in biodetection due to its superb chemical specificity and high sensitivity. The use of SERS substrates further improve this method by massive enhancement of the molecule Raman spectrum, permitting very low levels of detection. Therefore it is important to seek for new ways to develop reliable substrates, which are quickly and...
-
How to fund an additional secular function in the monumental church?
PublikacjaThe implementation of a new public function into the non-used church spaces like attics or cellars in context of revitalizing a lawfully protected historical city areas have diversified aspects. The article describes the financial aspect of adaptation of omitted spaces of monumental sacral buildings by presenting funding possibilities in the European Union countries available in period of 2017-2018 and the funds planned for the...
-
Fast surrogate-assisted frequency scaling of planar antennas with circular polarisation
PublikacjaIn this work, the problem of computationally efficient frequency scaling (re-design) of circular polarisation antennas is addressed using surrogate-assisted techniques. The task is challenging and requires the identification of the optimum geometry parameters to enable the operation of the re-designed structure at a selected (required) centre frequency. This involves handling several performance figures such as the antenna gain,...
-
Poloxamer: A versatile tri-block copolymer for biomedical applications
PublikacjaPoloxamers, also called Pluronic, belong to a unique class of synthetic tri-block copolymers containing central hydrophobic chains of poly(propylene oxide) sandwiched between two hydrophilic chains of poly(ethylene oxide). Some chemical characteristics of poloxamers such as temperature-dependent self-assembly and thermo-reversible behavior along with biocompatibility and physiochemical properties make poloxamer-based biomaterials...
-
Numerical analysis of mechanical properties of an infill structure used in 3D printings
PublikacjaThe paper presents results of a numerical analysis focused on an identification of mechanical properties of an element created by using Fused Deposition Modelling additive manufacturing technique (FDM). There is presented a description of technology of the 3D printing, numerical model created by using the finite element method (FEM), as well as some problems referred to estimation of the mechanical properties of the printout. The...
-
Comparison analysis of selected nuclear power plants supplied with helium from high-temperature gas-cooled reactor
PublikacjaThe article presents results of efficiency calculations for two 560 MW nuclear cycles with high-temperature gas-cooled reactor (HTGR). An assumption was made that systems of this type can be used in so-called marine nuclear power plants. The first analysed system is the nuclear steam power plant. For the steam cycle, the efficiency calculations were performed with the code DIAGAR, which is dedicated for analysing this type of systems....
-
Storing Matter’technique in SIMS depth profile analysis
PublikacjaSecondary ion mass spectrometry (SIMS) is a very useful technique for the analysis of layered systems. It is based on the primary ion beam sputtering of solids and mass analysis of the emitted secondary ions. A main limitation of this technique results from the direct quantitative analysis, since the ionization efficiency of a given atom is highly influenced by the neighbouring atoms at the surface. This phenomenon is known as...
-
Utilization of rapeseed pellet from fatty acid methyl esters production as an energy source
PublikacjaRapeseed pellet – crushed seed residue from oil extraction is a by-product of fatty acid methyl esters production process. As other types of biomass, it can either be burned directly in furnaces or processed to increase its energetic value. Biomass is renewable, abundant and has domestic usage; the sources of biomass can help the world reduce its dependence on petroleum products, fossil coal and natural gas. Energetically effective...
-
Efficiency of linear and non-linear classifiers for gas identification from electrocatalytic gas sensor
PublikacjaElectrocatalytic gas sensors belong to the family of electrochemical solid state sensors. Their responses are acquired in the form of I-V plots as a result of application of cyclic voltammetry technique. In order to obtain information about the type of measured gas the multivariate data analysis and pattern classification techniques can be employed. However, there is a lack of information in literature about application of such...
-
Mechanical behaviour of the implant used in human hernia repair under physiological loads
PublikacjaIn laparoscopic operations of abdominal hernias some recurrences still take place, even when applying a surgical mesh. This is usually caused by a failure of the connection between the tissue and the implant. The study deals with the influence of an implant’s orientation on forces in joints, which connect the mesh to human tissues. In the paper, the implant is modelled as a membrane structure within framework of the Finite Element...
-
Rigid polyurethane foams modified with selected layered silicate nanofillers
PublikacjaThe aim of this study was to investigate the effect of three different nanofillers on the properties of rigid polyurethane foams, which were prepared by a one-step, laboratory-scale method from a two-component system at the ratio of NCO groups to OH groups equaled to 2. The reaction mixture consisted of the proper amounts of the commercial oligoether polyol, catalysts, water, nanoclays, and polymeric diphenylmethane diisocyanate....
-
Miniaturized Passive Emission Chambers for In Situ Measurement of Emissions of Volatile Organic Compounds
PublikacjaThe results of many different studies have demonstrated unequivocally that the quality of indoor air is often much worse than that of atmospheric air. The presence of dangerous chemical compounds in indoor air can have an adverse impact on human health and cause numerous diseases of the respiratory and circulatory systems. Such harmful chemicals get into indoor air as a result of their emission from building and indoor materials....
-
Therapeutic intervention by the simultaneous inhibition of DNA repair and type I or type II DNA topoisomerases: one strategy, many outcomes
PublikacjaMany anticancer drugs reduce the integrity of DNA, forming strand breaks. This can cause mutations and cancer or cell death if the lesions are not repaired. Interestingly, DNA repair-deficient cancer cells (e.g., those with BRCA1/2 mutations) have been shown to exhibit increased sensitivity to chemotherapy. Based on this observation, a new therapeutic approach termed 'synthetic lethality' has been developed, in which radiation...
-
Waste Tyres Pyrolysis for Obtaining Limonene
PublikacjaThis review deals with the technologies of limonene production from waste tyre pyrolysis. Thermal decomposition is attractive for tackling the waste tyre disposal problem, as it enables both: energy to be recovered and limonene to be obtained. This material management recycling of tyres is environmentally more beneficial than the burning of all valuable products, including limonene. Given this recoverability of materials from waste...
-
CHARACTERIZATION STUDY ON MECHANICAL PROPERTIES OF POLYESTER COATED FABRIC
PublikacjaThe scope of the paper is to determine the mechanical properties of the Precontraint 1302 polyester coated fabric under uniaxial and biaxial tensile tests. The results are compared for Precontraint 1302 fabric and other types of coated fabrics. The author applied an orthotropic model and a dense net model to reflect the polyester coated fabric performance under uniaxial and biaxial tensile tests. Material parameters are specified...
-
In-Situ Processing of Biocomposites via Reactive Extrusion
PublikacjaLaw regulations, economic and environmental factors are the main causes for the rapidly growing interests in biocomposites’ research, conducted currently in a number of academic and industrial scientific centers. However, weak polymer matrix/filler interactions, common in biocomposites, result in unsatisfactory mechanical properties, which limit their practical applications. From many attempts performed to solve this problem, in-situ...
-
Assessing Acute Toxicity of Selected Packages Internal Layers Extracts using Microtox®
PublikacjaIn the scientific literature related to the widely understood issue of packaging materials designed to have contact with food (food contact materials), there is much information on raw materials used for their production, as well as their physiochemical properties, types and parameters. Unfortunately, not much attention is given to the issues concerning migration of toxic substances from packaging and its actual influence on the...
-
Analysis of passenger car crash with a cable barrier installed with anti-glare screens on a horizontal convex road curve with 400 m radius
PublikacjaHigh-tension cable barriers have been used on roads for a relatively short period compared with other types of road barriers. Hence, there remains a need for further research on various crash scenarios. An important issue is the performance of a cable barrier on a road curve, particularly when a vehicle impacts the convex side of the barrier. To address this issue, the analysis in this study considers a system of anti-glare screens...
-
THE ESSENCE OF THE TRANSFORMATION OF SOCIO-ECONOMIC RELATIONS IN THE NATIONAL ECONOMY: THEORETICAL AND METHODOLOGICAL ASPECT
PublikacjaThe article is devoted to a thorough study of the theoretical and methodological foundations of the essence of the transformation of socio-economic relations of the national economy. Based on the study of scientific sources, a proper definition of the concept of "transformation of socio-economic relations" was formed. It is proposed to consider transformational processes from the point of view of their direct or indirect impact...
-
VOCs absorption from gas streams using deep eutectic solvents – A review
PublikacjaVolatile organic compounds (VOCs) are one of the most severe atmospheric pollutants. They are mainly emitted into the atmosphere from anthropogenic sources such as automobile exhaust, incomplete fuel combustion, and various industrial processes. VOCs not only cause hazards to human health or the environment but also adversely affect industrial installation components due to their specific properties, i.e., corrosive and reactivity....
-
Development of the New Polish Method for Capacity Analysis of Motorways and Expressways
PublikacjaThe paper presents development of the new Polish method for performing capacity analysis of basic segments of dual carriageway roads (motorways and expressways). The method is based on field traffic surveys conducted at 30 motorway and expressway sites (class A and S roads) in Poland. Traffic flows, composition and travel times were observed in 15-min intervals at each site using ANPR filming method. These data were used to calibrate...
-
Comprehensive thermodynamic analysis of the CAES system coupled with the underground thermal energy storage taking into account global, central and local level of energy conversion
PublikacjaA key aspect of CAES is the optimal configuration of the thermodynamic cycle. In this paper, the situation of cooperation between the current conventional power plants and wind farms is analyzed, and then, based on thermodynamic models, the process of storing thermal and electrical energy in the CAES system coupled with a heat storage and recovery is developed. Therefore, three levels can be distinguished, namely: the global level...
-
Novel “acid tuned” deep eutectic solvents based on protonated L-proline
PublikacjaThe paper presents new types of deep eutectic solvents (DESs) based on L-proline protonated using three different acids (hydrochloric, sulfuric and phosphoric)and playing the role of a hydrogen bond acceptor(HBA). Glucose and xylitol were used as hydrogen bond donors (HBD). A series of deep eutectic solvents with various mole ratios were obtained for the systems L-proline: glucose and L-proline: xylitol. Density, melting point,...
-
1D convolutional context-aware architectures for acoustic sensing and recognition of passing vehicle type
PublikacjaA network architecture that may be employed to sensing and recognition of a type of vehicle on the basis of audio recordings made in the proximity of a road is proposed in the paper. The analyzed road traffic consists of both passenger cars and heavier vehicles. Excerpts from recordings that do not contain vehicles passing sounds are also taken into account and marked as ones containing silence....
-
Volumetric and torque efficiency of pumps during start-up in low ambient temperatures
PublikacjaThe volumetric, torque and total efficiency of hydraulic pumps change during start-up in low ambient temperatures, as well as in thermal shock conditions, un-til they reach the set conditions. The time to reach steady-state conditions de-pends on many parameters: ambient temperature, flow rate, fluid temperature, design of hydraulic units. The author carried out tests of hydraulic pumps in the Hydraulics Laboratory of the Faculty...