Wyszukiwarka
Filtry
wszystkich: 561
wybranych: 265
-
Katalog
- Publikacje 265 wyników po odfiltrowaniu
- Czasopisma 1 wyników po odfiltrowaniu
- Osoby 14 wyników po odfiltrowaniu
- Projekty 1 wyników po odfiltrowaniu
- Zespoły Badawcze 1 wyników po odfiltrowaniu
- Kursy Online 20 wyników po odfiltrowaniu
- Wydarzenia 1 wyników po odfiltrowaniu
- Dane Badawcze 258 wyników po odfiltrowaniu
Filtry wybranego katalogu
Wyniki wyszukiwania dla: ISO/TS 16949
-
Elastic polyurethane foams containing graphene nanoplatelets
PublikacjaElastic polyurethane foams were produced from two-component polyurethane systems (SPECFLEX NE 113 izocyjanian/NR 816 poliol system—SPC and Elastic MBMarket company system POLYOL ET MB 500/ISO ET MB 800—ET) by using a one-step method. The foams were a graphene nanoplatelets (GNP) in the amount ranging from 1 to 2 wt.%. The effect of the nanofiller on polyurethane matrix was determined by analyzing the chemical structure, static...
-
Bezpieczeństwo funkcjonalne i ochrona informacji w obiektach i systemach infrastruktury krytycznej – wymagania i kryteria
PublikacjaNiniejsza praca poświęcona jest zagadnieniom zarządzania bezpieczeństwem funkcjonalnym w cyklu życia z uwzględnieniem norm międzynarodowych PN-ENIEC 61508 i PN-ENIEC 61511 oraz zarządzaniu bezpieczeństwem informacji w systemach i sieciach komputerowych w nawiązaniu do wytycznych OECD i wymagań normy PN-ISO/IEC 27001. Rozważa się przykłady skupionych i rozproszonych sieci komputerowych pełniących funkcje monitorowania, sterowania...
-
Interactions of fish gelatin and chitosan in uncrosslinked and crosslinked with EDC films: FT-IR study
PublikacjaFilms based on fish gelatin, chitosan and blend of fish gelatin and chitosan before and after cross-linking with EDC have been characterized by FT-IR spectroscopy. The FT-IR spectrum of fish gelatin film showed the characteristic amide I, amide II and amide III bands, and the FT-IR spectrum of chitosan film confirmed that the polymer was only a partially deacetylated product, and included CH3-C=O and NH2 groups, the latter both...
-
Zakładowa Kontrola Produkcji w sektorze MŚP - propozycja metody zarządzania dokumentacją systemu
PublikacjaZakładowa Kontrola Produkcji (ZKP) to system jakości, który jest obligatoryjny dla producentów wyrobów budowlanych. Powinien on być udokumentowany i nadzorowany. Celem autorów, przyjętym w niniejszym opracowaniu, jest identyfikacja uwarunkowań dotyczących dokumentowania ZKP, analogii pomiędzy ZKP a systemem jakości według normy ISO 9001:2015 i innymi regulacjami oraz wskazanie korzyści i trudności związanych z dokumentowaniem działań...
-
Kinetic analysis of the reduction of a ternary system of Bi, Sb and Te oxides by hydrogen for BiSbTe3 synthesis
PublikacjaReduction in a hydrogen atmosphere of Bi2O3, Sb2O3 and TeO2 mixes oxides for the synthesis of BiSbTe3 was analysed. The reduction reactions of Sb2O3 and Sb2O4 oxides, as well as Bi2O3+Sb2O3 and Sb2O3+3TeO2 mix- tures, were also evaluated. The reduction of Sb2O4 is investigated for the first time. The reactions of the mixed oxides systems also were not the subject of research so far despite being used for synthesis of the (Bi,Sb)2Te3...
-
Roughness evaluation of turned composite surfaces by analysis of the shape of Autocorrelation Function
PublikacjaIn this paper, the application of an Autocorrelation Function for the characterisation of surface topography was validated. The roughness evaluation of turned composite surfaces was supported by sophisticated studies of the Autocorrelation Function properties, considering especially the shape of the function. Details were measured with the optical method. The selection of the surface roughness evaluation procedures was carried...
-
An integral-differential method for impedance determination of the hydrogen oxidation process in the presence of carbon monoxide in the proton exchange membrane fuel cell
PublikacjaThe impedance of a proton exchange membrane fuel cell powered by hydrogen contaminated with carbon monoxide, ranging from 150 to 300 ppb, is measured and discussed. The tested range of CO concentration complied with the fuel standard specified in the ISO standards. Studies of influence of CO contamination on operation of PEMFC are crucial for further development and commercialization of fuel cells for automotive applications. Based...
-
Designate of CTOD for WM and HAZ, report no: WOiO/II/122/2014
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
CTOD designation for WM and HAZ in butt joint made from S460 ML steel, Expertise No. WOiO/II/82/2015
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Standaryzacja i certyfikacja degradacji środowiskowej tworzyw sztucznych
PublikacjaDegradujące w środowisku naturalnym produkty z tworzyw sztucznych są grupą materiałów polimerowych, których ilość znacznie wzrosła w ostatnich latach. Ustanowiono wiele testów degradacji środowiskowej przez różne jednostki normalizacyjne. Testy te są również wykorzystywane, przy ustalaniu podstawowych systemów certyfikacji. Standardowe testy określają na przykład, jak pomiary biodegradacji danego materiału muszą być wykonane lub...
-
Six Sigma w małych i średnich przedsiębiorstwach. Puste hasło czy konieczność?
PublikacjaW artykule przedstawiono aspekty wykorzystania w sektorze małych i średnich przedsiębiorstw (MŚP) elementów koncepcji Six Sigma. Celem tego opracowania jest ocena potrzeb i uwarunkowań aplikacyjnych koncepcji Six Sigma w sektorze MŚP, zwłaszcza w nawiązaniu do bazujących na podejściu procesowym systemów zarządzania jakością. Zaprezentowano charakterystyczne cechy mniejszych organizacji, stanowiące w kontekście programów Six Sigma...
-
Designate CTOD Heat Affected Zone of butt weld, Report No: WOiO/II/76/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Designate CTOD of Weld Metal of butt weld, No WOiO/II/108/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATION ON SPECIMEN GEOMETRY EFFECT ON THE CTOD VALUE FOR VL-E36 SHIPBUILDING STEEL
PublikacjaThere are special cases in the marine industry, where additional material tests, such as the fracture toughness test, must be performed. Additional fracture toughness tests, such as CTOD (Crack Tip Opening Displacement), are typically performed on three-point bend specimens. The dimension that defines all the specimen dimensions is the thickness of the material to be tested. It is recommended by classification societies (e.g. DNVGL)...
-
Cross-layer integration of network mechanisms for increasing efficiency of multimedia session support in IEEE 802.11s environment
PublikacjaWith an IEEE 802.11 wireless networks operating in Point-to-Multipoint mode being the most popular WLAN access technology employed today, it can be expected that a Wireless Mesh Network (WMN) based on the technology can provide significant advantages for such network systems. The IEEE 802.11s standard amendment provides the comprehensive set of mechanisms required to implement and deploy a WMN utilizing this widely popular technology....
-
Eco-Friendly Ether and Ester-Urethane Prepolymer: Structure, Processing and Properties
PublikacjaThis study concerns bio-based urethane prepolymers. The relationship between the chemical structure and the thermal and processing parameters of bio-based isocyanate-terminated ether and ester-urethane prepolymers was investigated. Bio-based prepolymers were obtained with the use of bio-monomers such as bio-based diisocyanate, bio-based polyether polyol or polyester polyols. In addition to their composition, the bio-based prepolymers...
-
Model jakości bibliotek cyfrowych
PublikacjaBiblioteki cyfrowe zyskują z dnia na dzień coraz większą popularność, zarówno wśród osób poszukujących, jak i udostępniających informację. Twórcy bibliotek cyfrowych, mają do zaoferowania użytkownikom coraz to bardziej zaawansowane narzędzia przeznaczone do tworzenia, przeglądania i wyszukiwania dokumentów elektronicznych. Na przestrzeni ostatnich lat ustalony został kanon podstawowych funkcji, które powinna spełniać każda biblioteka...
-
Charakterystyka mechanizmów samoorganizującej się, wieloskokowej sieci bezprzewodowej w strefie B systemu netBaltic
PublikacjaStrefowa struktura systemu netBaltic pozwala na zastosowanie w jego obrębie odmiennych mechanizmów komunikacji sieciowej w zależności od dostępnych w określonym momencie dla danej jednostki możliwości komunikacyjnych. W strefie B systemu przewidziano wykorzystanie samoorganizującej, wieloskokowej sieci o strukturze kratowej, pozwalającej znacząco rozszerzyć zasięg łączności sieciowej poza obszar funkcjonowania lądowych systemów...
-
Functional Safety and Cybersecurity Analysis and Management in Smart Manufacturing Systems
PublikacjaThis chapter addresses some of the issues of the integrated functional safety and cybersecurity analysis and management with regard to selected references and the functional safety standards: IEC 61508, IEC 61511, ISO 13849-1 and IEC 62061, and a cybersecurity standard IEC 62443 that concerns the industrial automation and control systems. The objective is to mitigate the vulnerability of industrial systems that include the information...
-
At what temperature should the tire rolling resistance be measured?
PublikacjaThe climate crisis is already an indisputable fact and therefore, it is necessary to reduce energy consumption, and especially energy wasting. One of the ways to reduce energy consumption of motor vehicles is to decrease vehicle movement resistance, including rolling resistance. In order for the optimization of tire rolling resistance to be efficient, it is necessary to apply appropriate optimization criteria that are closely related...
-
Temperature influence on tire/road noise evaluated by the drum method
PublikacjaAmbient air and road surface temperatures substantially affect the road vehicle noise emission. The temperature influence on tire/road noise depends mainly on tire-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tires. The correction procedures for temperature effect are still under consideration and preparation. Laboratory experiment was prepared to...
-
Porównanie podejść do opisu kontekstu użycia z wykorzystaniem meta-modeli
PublikacjaOcena użyteczności może się różnić w zależności od rodzaju użytkownika oraz okoliczności, w których używany jest produkt. Aby uwzględnić ten fakt, do analizy wprowadzane jest pojęcie kontekstu użycia. W referacie zaprezentowano porównanie podejść do opisu kontekstu użycia oraz włączenia go w analizę użyteczności. Jest to część badań w ramach projektu, którego celem jest identyfikacja i opis kontekstu użycia narzędzi UML. Referat...
-
Polymerization of chloro-p-xylylenes, quantum-chemical study
PublikacjaThe p-xylylene monomers of parylene N, C and D have similar high polymerization reactivity. For effective copolymerization processes this fact is basically a draw- back and for instance the copolymerization with styrene doesn't go at all (Corley et al. J Pol Sc 13(68):137156, 1954). Substitution of terminal hydrogen atoms by chlorine atoms reduces reactivity dramatically. 7,7,8,8-tetrachloro-p- xylylene and 2,5,7,7,8,8-hexachloro-p-xylylene...
-
Double-diffusive natural convection energy transfer in magnetically influenced Casson fluid flow in trapezoidal enclosure with fillets
PublikacjaThe prime motive of this disquisition is to deal with mathematical analysis of natural convection energy transport driven by combined buoyancy effects of thermal and solutal diffusion in a trapezoidal enclosure. Casson fluid rheological constitutive model depicting attributes of viscoelastic liquids is envisioned. The influence of the inclined magnetic field governed by Lorentz field law is also considered. To raise the essence...
-
The impedance of hydrogen oxidation reaction in a proton exchange membrane fuel cell in the presence of carbon monoxide in hydrogen stream
PublikacjaEvaluation of performance of a proton exchange membrane fuel cell, which is affected by carbon monoxide that pollutes the hydrogen stream, was presented. This influence was studied for carbon monoxide concentration of 125–325 ppb, which are close to values specified in ISO 14687:2019 standard. Performed studies provided crucial information for further development of fuel cell as an energy source for automotive application. Impedance...
-
ASSESSING THE POTENTIAL REPLACEMENT OF MINERAL OIL WITH ENVIRONMENTALLY ACCEPTABLE LUBRICANTS IN A STERN TUBE BEARING: AN EXPERIMENTAL ANALYSIS OF BEARING PERFORMANCE
PublikacjaT his study compares the performance of a plain bearing, with a similar structure to a tail shaft stern bearing, lubricated with either mineral oil or an environmentally acceptable lubricant (EAL). The main characteristic of the bearing is its length/diameter ratio of <1. Measurements are carried out with the bearing operating under loads from 0.5 to 1 MPa and seven speeds ranging from 1 to 11 rev/s. The bearing lubricated...
-
Analiza bezpieczeństwa funkcjonalnego i ochrony informacji w rozproszonych systemach komputerowych pełniących funkcje sterowania i zabezpieczeń
PublikacjaW niniejszym artykule przedstawiona została problematyka związana z analizą bezpieczeństwa funkcjonalnego rozproszonych systemów sterowania i automatyki zabezpieczeniowej z uwzględnieniem zagadnień ochrony informacji. Powinny być one rozpatrywane w sposób zintegrowany w zależności od rodzaju komunikacji stosowanej do transmisji danych. W tym celu zaproponowano podział analizowanych systemów na trzy kategorie. Zaproponowane podejście...
-
Analiza bezpieczeństwa funkcjonalnego i ochrony informacji w rozproszonych systemach komputerowych pełniących funkcje sterowania i zabezpieczeń
PublikacjaW niniejszym artykule przedstawiona została problematyka związana z analizą bezpieczeństwa funkcjonalnego rozproszonych systemów sterowania i automatyki zabezpieczeniowej z uwzględnieniem zagadnień ochrony informacji. Powinny być one rozpatrywane w sposób zintegrowany w zależności od rodzaju komunikacji stosowanej do transmisji danych. W tym celu zaproponowano podział analizowanych systemów na trzy kategorie. Zaproponowane podejście...
-
Advantages of the Application of the Temper Bead Welding Technique During Wet Welding
PublikacjaThermo-mechanically rolled S460ML steel was chosen for welding in underwater wet welding conditions by covered electrodes. The main aim of this study was to check the weldability for fillet welds in a water environment by controlled thermal severity (CTS) tests and to check the influence of temper bead welding (TBW) on the weldability of the investigated steel. Non-destructive and destructive tests showed that S460ML steel has...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublikacjaTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublikacjaA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
Degradation of xylose using a microbial fuel cell
PublikacjaIt is generally known, that many kind of microorganisms are capable of using carbohydrates as a source of carbon and energy in an environment. The biodegradation process of monosaccharides from pentoses (in this case- racemic mixture of D - and L – xylose) is an immense opportunity for an entire reduction of biological contamination to neutral compounds through MFC. The process is occurred in a single-chamber MFC, which is contained...
-
Generatory zmian służące doskonaleniu usług medycznych
PublikacjaW rozdziale zaprezentowano podstawowe aspekty usług medycznych. Opisano typowe cechy usług, które odniesiono do usług medycznych, a także wyznaczono specyficzne cechy dla tego rodzaju usług. Następnie podjęto próbę zdefiniowania pojęcia jakość w usługach medycznych w nawiązaniu do potrzeb pacjenta. W rozdziale przybliżono najważniejsze z obecnie stosowanych, mechanizmów zapewnienia jakości w usługach medycznych, którymi są: Certyfikacja...
-
RAPORT - EKSPERTYZA Z POMIARÓW DRGAŃ LINII WAŁÓW NA JEDNOSTCE R14
PublikacjaEkspertyza diagnostyczna dotycząca stanu technicznego lini transmisji mocy (linii wałów) opracowana na podstawie przeprowadzonych pomiarów drgań. Pomiary prędkości i przyspieszeń drgań generowanych przez węzły konstrukcyjne linii wałów okrętowego układu napędowego wykonano po naprawie głównej napędu okrętu w stoczni „NAUTA”, w celu określenia jego stanu dynamicznego. Rejestrację drgań przeprowadzono w płaszczyźnie pionowej (V)...
-
Studies of the separation performance of silanized silica gel for simulated distillation
PublikacjaWe present the results of investigations of the chromatographic (sorptive) properties of silanized silica gel as a stationary phase for gas chromatography used for simulated distillation. Commercially available silanized sorbent (particle diameter range 63–200 m, average pore size 60 Å) was sieved to obtain the 80–100 mesh fraction (180–150 m). The obtained results revealed that silanized silica gel allows the complete separation...
-
Fracture surface topography measurements analysis of low-alloyed corrosion resistant steel after bending-torsion fatigue tests
PublikacjaIn this paper, an assessment of a topography measurement method for fracture surfaces of 10HNAP steel after bending-torsion fatigue tests was performed. Surface roughness was measured by using a non-contact Focus Variation Microscopy (FVM) technique in which the non-measured points (NMPs) and outliers (spikes) were removed by the application of general methods. The results revealed, that the optical measurement method introduced...
-
Microstructural evolution and mechanical behavior of activated tungsten inert gas welded joint between P91 steel and Incoloy 800HT
PublikacjaThis study examines the welded joint between P91 steel and Incoloy 800HT using the Activated Tungsten Inert Gas (A-TIG) welding process. The focus is on analyzing the microstructure and evaluating the mechanical properties of joints made with different compositions of activating flux. Owing to the reversal of the Marangoni effect in which the conventional direction of molten metal flow in the weld pool is reversed due to the application...
-
Ab initio chemical kinetics of Isopropyl acetate oxidation with OH radicals
PublikacjaGlobal reactivity descriptors of isopropyl acetate (IPA) and thermo-kinetic aspects of its oxidation via OH radicals have been studied. Transition state theory (TST) was utilized to estimate the bimolecular rate constants. Ten oxidation pathways have been investigated, and all of them are exothermic. The potential energy diagram has been sketched using different pre- and post-reactive complexes for all reaction pathways. Rate coefficient...
-
TDOA versus ATDOA for wide area multilateration system
PublikacjaThis paper outlines a new method of a location service (LCS) in the asynchronous wireless networks (AWNs) where the nodes (base stations) operate asynchronously in relation to one another. This method, called asynchronous time difference of arrival (ATDOA), enables the calculation of the position of the mobile object (MO) through the measurements taken by a set of non-synchronized fixed nodes and is based on the measurement of...
-
RAPORT-EKSPERTYZA Z POMIARÓW DRGAŃ LINII WAŁÓW NA JEDNOSTCE ORP „PIORUN”
PublikacjaEkspertyza diagnostyczna dotycząca stanu technicznego lini transmisji mocy (linii wałów) opracowana na podstawie przeprowadzonych pomiarów drgań. Pomiary prędkości i przyspieszeń drgań generowanych przez węzły konstrukcyjne linii wałów okrętowego układu napędowego wykonano po naprawie głównej napędu okrętu w stoczni „NAUTA”, w celu określenia jego stanu dynamicznego. Rejestrację drgań przeprowadzono w: • płaszczyźnie pionowej (V)...
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublikacjaThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
Numerical analysis of vacuum drying of a porous body in the integrated domain
Publikacjan the present study, the vacuum drying process of an apple slice is numerically modeled based on a control volume method. Transient two-dimensional Navier– Stokes, energy, moisture, and Luikov equations are solved by numerical coding (Fortran) to simulate the simultaneous heat and mass transfer in the ambient and apple slice, respectively. The privilege of using Luikov's model is that the capillary forces are considered, and a...
-
Corrosivity of environment and the current state of the steel elements at the former Auschwitz concentration camp
PublikacjaThe objective of this study was to assess corrosivity of the atmospheric environment in the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp, and to identify the protective properties of existing corrosion products in order to estimate the actual corrosion rate of original steel elements located there. The current atmospheric corrosivity of the former Auschwitz camp, specified during one year of exposure...
-
INFLUENCE OF MEASURING CONDITIONS ON TYRE/ROAD NOISE
PublikacjaA decisive factor for the development of tyres and road surfaces is the ability to conduct representative and reproducible measurements of selected characteristics related to the interaction of tyres and road surfaces. In terms of tyre/road noise measurements in Europe two methods described in ISO/FDIS 11819-2 and ECE Regulation No.117 are used. The latter is compulsory for assigning the tyre noise labels. The methodologies differ...
-
Modele strumienia powietrza w pneumatyce
PublikacjaPraca porusza problematykę modelowania strumienia masy i strumienia objętości w zadaniach analizy i syntezy w pneumatyce. W szczególności skoncentrowano się na możliwości wykorzystania w tych zagadnieniach modelu strumienia masy powietrza opisanego w normie ISO 6953. Jest to model zdefiniowany w dziedzinie ciśnień statycznych i wykorzystujący do określenia oporności elementu pneumatycznego cztery parametry (współczynniki przepływu):...
-
Reduction in Errors in Roughness Evaluation with an Accurate Definition of the S-L Surface
PublikacjaCharacterization of surface topography, roughly divided into measurement and data analysis, can be valuable in the process of validation of the tribological performance of machined parts. Surface topography, especially the roughness, can respond straightly to the machining process and, in some cases, is defined as a fingerprint of the manufacturing. When considering the high precision of surface topography studies, the definition...
-
Thermal-Resistant Polyurethane/Nanoclay Powder Coatings: Degradation Kinetics Study
PublikacjaIn the present study, thermal degradation kinetics of polyurethane (PU) powder coatings reinforced with organo-modified montmorillonite (OMMT) was investigated. PU nanocomposites were prepared in different concentrations of 1, 3, and 5 wt.% of OMMT via the extrusion method. The microstructure of the nanocomposites was observed by scanning electron microscope (SEM) illustrating uniform dispersion of OMMT nano-clay platelets in the...
-
PLA–Potato Thermoplastic Starch Filament as a Sustainable Alternative to the Conventional PLA Filament: Processing, Characterization, and FFF 3D Printing
PublikacjaThe growing popularity of the fused filament fabrication (FFF) 3D printing technology in science, industry, and in-home use is associated with an increased demand for high-quality polymer filaments. This study presents an in-depth characterization and analysis of a self-made bio-based polylactide (PLA)/thermoplastic potato starch (TPS) filament dedicated for the FFF 3D printing technology. The obtained results were compared with...
-
Processing of Polyester-Urethane Filament and Characterization of FFF 3D Printed Elastic Porous Structures with Potential in Cancellous Bone Tissue Engineering
PublikacjaThis paper addresses the potential of self-made polyester-urethane filament as a candidate for Fused Filament Fabrication (FFF)-based 3D printing (3DP) in medical applications. Since the industry does not provide many ready-made solutions of medical-grade polyurethane filaments, we undertook research aimed at presenting the process of thermoplastic polyurethane (TPU) filament formation, detailed characteristics, and 3DP of specially...
-
Comparison of Tire Rolling Resistance Measuring Methods for Different Surfaces
PublikacjaThe rolling resistance of car tires is one of the most important parameters characterizing tires today. This resistance has a very significant contribution to the energy consumption of wheeled vehicles. The climate crisis has forced tire and car manufacturers to place great emphasis on the environmental impact of their products. Paradoxically, the development of electric vehicles has led to an even greater importance of rolling...