Filtry
wszystkich: 561
wybranych: 539
Wyniki wyszukiwania dla: SAFETY AND RELIABILITY
-
ANALYSIS OF THE LOAD-CARRYING CAPACITY OF A HYDRODYNAMIC WATER-LUBRICATED BEARING IN A HYDROELECTRIC POwER PLANT
PublikacjaThe paper presents an analysis of the load-carrying capacity of a historic hydrodynamic water-lubricated radial bearing of an unconventional segment design installed in the Braniewo Hydroelectric Power Plant. The aim of the calculations was to determine whether the bearing operates in the conditions of hydrodynamic or mixed lubrication, as well as to establish the optimal geometry of the axial grooves allowing for the highest load-carrying...
-
Underwater acoustic communication system using broadband signal with hyperbolically modulated frequency
PublikacjaThe implementation of reliable acoustic underwater communication in shallow waters is a scientific and engineering challenge, mainly due to the permanent occurrence of the multipath phenomenon. The article presents the concept of a transmission system using a broadband signal with hyperbolically modulated frequency (HFM) to transmit data symbols and synchronize data frames. The simulation tests were carried out in channels with...
-
Validation of dynamic electrochemical impedance spectrograms using autocorrelation function
PublikacjaValidation of impedance data is essential for checking the reliability of experimental data. Kramers – Kronig transformation is used to verify data obtained from classical Electrochemical Impedance Spectroscopy (EIS) measurements. Data obtained from Dynamic Electrochemical Impedance Spectroscopy (DEIS) could be validated in the same way, but in this case, there is no information about internal consistency between every single spectrum...
-
Open-Phase Fault Detection Method for Sensorless Five-Phase Induction Motor Drives with an Inverter Output Filter
PublikacjaThe paper presents the sensorless five-phase induction motor drive implementation with an inverter output filter with third harmonic injection. For the sensorless operation, the required observers are presented for the first and third harmonics with consideration of the inverter output filter. Moreover, the interaction of the observers and the control system is capable to handle a deactivation of one or two phases, which improves...
-
Improved-Efficacy Optimization of Compact Microwave Passives by Means of Frequency-Related Regularization
PublikacjaElectromagnetic (EM)-driven optimization is an important part of microwave design, especially for miniaturized components where the cross-coupling effects in tightly arranged layouts make traditional (e.g., equivalent network) representations grossly inaccurate. Efficient parameter tuning requires reasonably good initial designs, which are difficult to be rendered for newly developed structures or when re-design for different operating...
-
Application of wireless communication to small WECS with induction generator
PublikacjaWind energy conversion systems (WECS) seem to be self-evident elements of the future smart grids. Among many generator types the squirrel cage induction generator (SCIG) characterizes robustness and low cost. A full-scale power converter can perform smooth grid connection over wide speed range of multiple-stage geared SCIG. Increasing number of sensors can improve the WECS control and diagnostics but increasing number of thin wires...
-
Assesment of operation of ship main diesel engine using the theory of semi-markovian and markov processes.
PublikacjaTo precisely determine the task it is necessary to specify also its duration time, apart from conditions in which it will be realized. When considering propulsion engine, i.e. the main element of ship propulsion system, especially important becomes not only the problem which amount of energy could be at one's disposal but also within which time interval it could be delivered. Therefore apart from applying the commonly used reliability...
-
A Concept of Modeling and Optimization of Applications in Large Scale Systems
PublikacjaThe chapter presents the idea that includes modeling and subsequent optimization of application execution on large scale parallel and distributed systems. The model considers performance, reliability and power consumption. It should allow easy modeling of various classes of applications while reflecting key parameters of both the applications and two classes of target systems: clusters and volunteer based systems. The chapter presents...
-
Smart heating system for home extending utilization of renewable energy sources
PublikacjaIn the paper a modern approach to smart home heating is presented. Proposed solution utilizes at least two low-polluting energy source technologies. The main idea is to connect well known ecological energy sources in a way that they can support each other and minimize risks of failure when using single system or even both of them but managed in separate way. Considered energy technologies, used separatelly, have disadvan-tages,...
-
Secured wired BPL voice transmission system
PublikacjaDesigning a secured voice transmission system is not a trivial task. Wired media, thanks to their reliability and resistance to mechanical damage, seem an ideal solution. The BPL (Broadband over Power Line) cable is resistant to electricity stoppage and partial damage of phase conductors, ensuring continuity of transmission in case of an emergency. It seems an appropriate tool for delivering critical data, mostly clear and understandable...
-
Wake-Up Receiver for Underwater Acoustic Communication Using in Shallow Water
PublikacjaA data frame transmitted over the underwater acoustic channel usually begins with a preamble. Therefore, underwater communication systems have a dedicated receiver that constantly listens to the preamble signals. A receiver that is to work effectively in shallow waters must have solutions that effectively reduce the impact of the permanently occurring multipath propagation. The article presents a solution based on complementary...
-
Comparative in vitro research of the Human Aortic Bioprosthesis
PublikacjaE valuate of the usefulness and reliability of structures based on the analysis of recorded parameters determining the flow through the Human Aortic Bioprosthesis (HAB) have been dealt with. By flow parameters changes determining the performance environment of prosthesis analyzed change of the motion dynamics of the valve leaflets as a function of pressure, thereby determining the degree of alignment of the prosthesis to the performance...
-
Harmony Search for Self-configuration of Fault–Tolerant and Intelligent Grids
PublikacjaIn this paper, harmony search algorithms have been proposed to self-configuration of fault-tolerant grids for big data processing. Self-configuration of computer grids lies in the fact that new computer nodes are automatically configured by software agents and then integrated into the grid. A base node works due to several configuration parameters that define some aspects of data communications and energy power consumption. We...
-
Prototype of a low-cost luxmeter with wide measuring range designed for railway stations dynamic lighting systems
PublikacjaThe paper presents the development of a low-cost luxmeter designed for usage in automatic applications for continual (long-term) measurement of illuminance. The measured information is used to adjust the level of lighting systems of artificial lighting on railways (platforms, marshalling yard, tracks etc.). The reason of this measuring device is a requirement for massive deployment of dimmable lighting systems for railways, in...
-
Emotion Monitor - Concept, Construction and Lessons Learned
PublikacjaThis paper concerns the design and physical construction of an emotion monitor stand for tracking human emotions in Human-Computer Interaction using multi-modal approach. The concept of the stand using cameras, behavioral analysis tools and a set of physiological sensors such as galvanic skin response, blood-volume pulse, temperature, breath and electromyography is presented and followed...
-
Reliable Document-Centric Processing in Loosely Coupled Email-Based Systems
PublikacjaEmail is a simple way to exchange digital documents of any kind. The Mobile INteractive Document architecture (MIND) enables self-coordination and self-steering of document agent systems based on commonly available email services. In this paper, a mechanism for providing integrity and reliability of such an email based agent system is proposed to cope with message soft or hard bounces, user interrupts, and other unexpected events....
-
Problems of Active Dynamic Thermography Measurement Standardization in Medicine
PublikacjaReliability of thermographic diagnostics in medicine is an important practical problem. In the field of static thermography, a great deal of effort has been made to define the conditions for thermographic measurements, which is now the golden standard for such research. In recent years, there are more and more reports on dynamic tests with external stimulation, such as Active Dynamic Thermography, Thermographic Signal Reconstruction...
-
Expedited Yield Optimization of Narrow- and Multi-Band Antennas Using Performance-Driven Surrogates
PublikacjaUncertainty quantification is an important aspect of engineering design, also pertaining to the development and performance evaluation of antenna systems. Manufacturing tolerances as well as other types of uncertainties, related to material parameters (e.g., substrate permittivity) or operating conditions (e.g., bending) may affect the antenna characteristics. In the case of narrow- or multi-band antennas, this usually leads to...
-
Rapid tolerance‐aware design of miniaturized microwave passives by means of confined‐domain surrogates
PublikacjaThe effects of uncertainties, primarily manufacturing tolerances but also incomplete information about operating conditions or material parameters, can be detrimental to the performance of microwave components. Quantification of such effects is essential to ensure a meaningful evaluation of the structure, in particular, its reliability under imperfect fabrication procedures. The improvement of the circuit robustness can be achieved...
-
Exploiting audio-visual correlation by means of gaze tracking
PublikacjaThis paper presents a novel means for increasing audio-visual correlation analysis reliability. This is done based on gaze tracking technology engineered at the Multimedia Systems Department of the Gdansk University of Technology, Poland. In the paper, the past history and current research in the area of audio-visual perception analysis are shortly reviewed. Then the methodology employing gaze tracking is presented along with the...
-
Zarządzanie bezpieczeństwem w złożonych obiektach i instalacjach krytycznych
PublikacjaW rozdziale scharakteryzowano wybrane metody wspomagające zarządzanie bezpieczeństwem w systemach technicznych, w tym metodę RCM (reliability-centered maintenance) polegającą na proaktywnej obsłudze, której celem jest nie dopuszczać lub przynajmniej ograniczać skutki potencjalnych uszkodzeń oraz metodę RBM (risk-based maintanance) i procedurę RIMAP (risk-based inspection and maintanance procedures) stosowaną w zarządzaniu bezpieczeństwem...
-
Integrating heterogeneous systems with high-dependability requirements by means of web services
PublikacjaWeb services are commonly used on boundaries of heterogeneous components in Service Oriented Architecture (SOA) as they provide a universal communication channel not bound to any particular programming language or run-time platform. This paper describes how web services can be used to integrate heterogeneous systems which serve purposes requiring high dependability, reliability and availability. Examples of such systems include...
-
Reliability of acicular grindable thermocouples for transient temperature measurements at sliding contacts
PublikacjaAcicular grindable thermocouples represent an interesting and prospective technique of temperature measurements at sliding contacts. This study aimed at the investigation of their reliability and accuracy as applied to the friction materials of various classes in contact with steel. The tests were conducted on a pin-on-disc tribometer under stationary and transient regimes. The experimental results were validated by comparing the...
-
The Impact of Lexicon Adaptation on the Emotion Mining From Software Engineering Artifacts
PublikacjaSentiment analysis and emotion mining techniques are increasingly being used in the field of software engineering. However, the experiments conducted so far have not yielded high accuracy results. Researchers indicate a lack of adaptation of the methods of emotion mining to the specific context of the domain as the main cause of this situation. The article describes research aimed at examining whether the adaptation of the lexicon...
-
Wireless Networks as an Infrastructure for Mission-Critical Business Applications
PublikacjaDespite the dynamic growth of wireless network systems, their pres-ence in business-support infrastructure has been limited. In the article we provide an overview of generic corporate network architecture and examine usefulness of available wireless network solutions in such systems. Following this overview we analyze new wireless network architecture which currently undergoes standardization process - wireless mesh. It can result...
-
Multilevel inverter neutral-point voltage sensor diagnostic based on the Extended Kalman Filter
PublikacjaA new algorithm for neutral point voltage imbalance estimation in DC link of the three-level (3L) neutral point clamped (NPC) voltage source inverter (VSI) is proposed. Application of the proposed algorithm does not require any additional sensors. The unbalanced voltage calculation is based on the information derived from the inverter output measured currents and from the knowledge of the load model parameters. In order to estimate...
-
A Measurement-Based Approach for Speed Control of Induction Machines
PublikacjaThis paper presents an approach to design a measurement-based controller for induction machines. The proposed control approach is motivated by the fact that developing an appropriate mechanical model of such induction machines is a challenging task. Since our proposed control methodology is only on the basis of measured data, the controller design does not require any information about the model of the mechanical part. The control...
-
Size Reduction of Microwave Couplers by EM-Driven Optimization
PublikacjaThis work addresses simulation-driven design optimization of compact microwave couplers that explicitly aims at circuit footprint area reduction. The penalty function approach allows us to minimize the area of the circuit while ensuring a proper power division between the output ports and providing a sufficient bandwidth with respect to return loss and isolation around the operating frequency. Computational cost of the optimization...
-
HYDROSTATIC THRUST BEARING WITH REDUCED POWER LOSSES
PublikacjaIn many cases in rotating machinery, axial load is carried by tilting pad thrust bearings which have been developed since the beginning of 20th century. For high reliability and simplicity, most commonly the bearings are bath lubricated. In the times of sustainable development, however, minimization of friction losses becomes an important criterion for machinery assessment, and a strategic goal of their development. Performed calculations,...
-
Expedited Yield-Driven Design of High-Frequency Structures by Kriging Surrogates in Confined Domains
PublikacjaUncertainty quantification is an important aspect of engineering design, also pertaining to the development and performance evaluation of high-frequency structures systems. Manufacturing tolerances as well as other types of uncertainties, related to material parameters (e.g., substrate permittivity) or operating conditions (e.g., bending) may affect the characteristics of antennas or microwave devices. For example, in the case...
-
Efficient Calibration of Cost-Efficient Particulate Matter Sensors Using Machine Learning and Time-Series Alignment
PublikacjaAtmospheric particulate matter (PM) poses a significant threat to human health, infiltrating the lungs and brain and leading to severe issues such as heart and lung diseases, cancer, and premature death. The main sources of PM pollution are vehicular and industrial emissions, construction and agricultural activities, and natural phenomena such as wildfires. Research underscores the absence of a safe threshold for particulate exposure,...
-
Influence of Soft Soil Samples Quality on the Compressibility and Undrained Shear Strength – Seven Lessons Learned From the Vistula Marshlands
PublikacjaThis technical article presents the influence of sample quality on the compressibility parameters and undrained shear strength ( c u ) of soft soils from the Vistula Marshlands. The analysis covers: (1) quality of soft soil according to three criteria: void ratio (Δ e / e 0 index), volumetric strain (Δ ɛ v ) and C r / C c ratio; (2) influence of storage time on quality; (3) influence of sample quality on undrained shear strength...
-
Probabilistic sensitivity of limit states of structures : The Monte Carlo simulation
PublikacjaThe main issue of the paper is the probabilistic sensitivity of the limit states of structures with respect to selected input design variables. Attempt to the problem is done by the dedicated Monte Carlo simulation procedure. Basic design variables are random variables of given probability distributions, presented in the form of random numbers. Uni-parametrical increment of the dominant basic variable (basic variables) is done,...
-
Audio codec employing frequency-derived tonality measure
PublikacjaA transform codec employing efficient algorithm for detection of spectral tonal components is presented. The tonality measure used in MPEG psychoacoustic model is replaced with the method providing adequate tonality estimates even if the tonal components are deeply frequency modulated. The reliability of hearing threshold estimated using psychoacoustic model with standardized tonality measure and the proposed one is investigated...
-
Mathematical modelling of the overhead contact line for the purpose of diagnostics of pantographs
PublikacjaThe overhead contact line (OCL) is the most effective way for supplying railway electric vehicles. The increase of the speed of the vehicles increases power consumption and requires ensuring proper cooperation of pantographs with OCL. The paper describes the novel mathematical model of the OCL system and the simulation results. The primary objective is a more accurate analysis to increase the reliability of the evaluation of monitoring...
-
The impact of material degradation on the resistance and reliability of truss structures
PublikacjaThe paper analyses limit load-carrying capacity and buckling load of truss towers used to support high voltage power lines. The analysed typical structure was subjected to characteristic loads and their combinations. The results were applied to assess structural resistance with regard to steel corrosion in the long-term operation. The extent of structural deterioration was assessed due to Young's modulus decrement in the course...
-
Rapid surrogate-assisted statistical analysis of compact microstrip couplers
PublikacjaIn this paper, a technique for low-cost statistical analysis and yield estimation of compact microwave couplers has been presented. The analysis is executed at the level of a fast surrogate model representing selected characteristic points of the coupler response that are critical to determine satisfaction/violation of the prescribed design specifications. Because of less nonlinear dependence of the characteristic points on geometry...
-
DUABI - Business Intelligence Architecture for Dual Perspective Analytics
PublikacjaA significant expansion of Big Data and NoSQL databases made it necessary to develop new architectures for Business Intelligence systems based on data organized in a non-relational way. There are many novel solutions combining Big Data technologies with Data Warehousing. However, the proposed solutions are often not sufficient enough to meet the increasing business demands, such as low data latency while still maintaining high...
-
UAV IN TODAYS PHOTOGRAMMETRY – APPLICATION AREAS AND CHALLENGES
PublikacjaThere a few important factors, that nowadays, unmanned aerial vehicles (UAV) are used by wider community, and for cases and applications, that cannot be performed never before. Small UAVs, as a photogrammetry measurement tool provide flexibility, reliability, are safe and easy to use, can be deployed in minutes, initial measurement can be delivered yet on the field, and final accurate measurements are calculated in a very short...
-
Analiza nośności granicznej losowego podłoża pod fundamentem metodami pierwszego rzędu
PublikacjaPraca dotyczy opisu i analizy losowego ośrodka gruntowego metodami pierwszego rzędu. W ujęciu probabilistycznym, efektywną i prostą w użyciu jest tu metoda estymacji momentów, znana jako FOSM (First Order Second Moment). Z kolei w ramach teorii niezawodności konstrukcji, jednym z najskuteczniejszych sposobów analizy jest metoda FORM (First Order Reliability Method). W pracy, krótko omówione obydwie metody i zastosowano je do analizy...
-
Analysis of positioning methods using Global Navigation Satellite Systems (GNSS) in Polish State Railways (PKP)
PublikacjaEach year, global navigation satellite systems (GNSS) improve their accuracy, availability, continuity, integrity, and reliability. Due to these continual improvements, the systems are increasingly used in various modes of transport, including rail transport, the subject of this publication. GNSS are used for rail passenger information, rail traffic management, and rail traffic control. These applications differ in the positioning...
-
Polynomial Algorithm for Minimal (1,2)-Dominating Set in Networks
PublikacjaDominating sets find application in a variety of networks. A subset of nodes D is a (1,2)-dominating set in a graph G=(V,E) if every node not in D is adjacent to a node in D and is also at most a distance of 2 to another node from D. In networks, (1,2)-dominating sets have a higher fault tolerance and provide a higher reliability of services in case of failure. However, finding such the smallest set is NP-hard. In this paper, we...
-
Interline power flow controller - properties and control strategy in dynamic states
PublikacjaHigh-power electronic converter topologies, in such forms as Unified Power Flow Controllers (UPFC), Static Compensators (STATCOM) and Interline Power Flow Controllers (IPFC), have been used to enhance and optimize the use of transmission facilities, under the concept of a flexible ac transmission system (FACTS). In Europe, the anticipated proliferation of distributed-generation (DG) in the near future, driven by governmental initiatives...
-
Low-fidelity model considerations for simulation-based optimisation of miniaturised wideband antennas
PublikacjaHere, variable-fidelity electromagnetic (EM)-based design optimisation of miniaturised antennas is discussed. The authors focus on an appropriate selection of discretisation density of the low-fidelity EM model, which results in good performance of the optimisation algorithm in terms of its computational complexity and reliability. Trust-region gradient search with low-fidelity model corrected by means of non-linear frequency scaling...
-
On low-fidelity models for variable-fidelity simulation-driven design optimization of compact wideband antennas
PublikacjaThe paper addresses simulation-driven design optimization of compact antennas involving variable-fidelity electromagnetic (EM) simulation models. Comprehensive investigations are carried out concerning selection of the coarse model discretization density. The effects of the low-fidelity model setup on the reliability and computational complexity of the optimization process are determined using a benchmark set of three ultra-wideband...
-
Structure and computationally-efficient simulation-driven design of compact UWB monopole antenna
PublikacjaIn this letter, a structure of a small ultra-wideband (UWB) monopole antenna, its design optimization procedure as well as experimental validation are presented. According to our approach, antenna compactness is achieved by means of a meander line for current path enlargement as well as the two parameterized slits providing additional degrees of freedom that help to ensure good impedance matching. For the sake of reliability, the...
-
A CONCEPT DESIGN OF DIESEL – HYDRAULIC PROPULSION SYSTEM FOR PASSENGER SHIP INTENDED FOR INLAND SHALLOW WATER NAVIGATION
PublikacjaThis paper presents an analysis of environmental and technical conditions necessary for working out a possibly most favourable propulsion system for a two – segment passenger ship intended for navigation between Berlin and Kaliningrad. There are presented various types of propulsion systems for small ships as well as analyzed their possible applications and consequences. In this work there were taken into account system’s reliability,...
-
Assessment of image processing methods for the determination of propagation of squat-type defects in rails
PublikacjaWe demonstrate the idea of squat-type defect measurement in the rail and the concept of tracking of the defect development using the techniques of image acquisition and image processing as well as the methods of metric spaces. We introduce the concepts of a set diameter δ(A) and the metric ρ1, which come from the properties of plane figures, to compare and to observe the development of the defects. We characterize the feasibility...
-
Integration of inertial sensors and GPS system data for the personal navigation in urban area
PublikacjaGPS and Inertial Navigation Systems (INS) have complementary properties and they are therefore well suited for integration. The integrated solution offers better long-term accuracy than a stand-alone INS and better integrity, availability and continuity or a stand-alone GPS receiver, making it suitable for demanding applications. The complementary features of INS and GPS are the main reasons why integrated GPS/INS systems are becoming...
-
Estimation of the Ultimate Strength of FRP Strips-to-Masonry Substrates Bond
PublikacjaFiber-Reinforced Polymers (FRP) were developed as a new method over the past decades due to their many beneficial mechanical properties, and they are commonly applied to strengthen masonry structures. In this paper, the Artificial Neural Network (ANN), K-fold Cross-Validation (KFCV) technique, Multivariate Adaptive Regression Spline (MARS) method, and M5 Model Tree (M5MT) method were utilized to predict the ultimate strength of...