Wyszukiwarka
Wyniki wyszukiwania dla: ELECTRICAL METHODS
-
High-efficiency mini and micro heat exchangers for dispersed power generation
PublikacjaTaking into account the dispersed systems technologies and their development, the ORC systems seem to be promising technology amongst various micro-CHP domestic units (electrical power production below 10 kWe), however practical realization of the ORC cycle in a micro-scale is technically challenging. The system consists in devices such as the vapour generation unit (boiler), expansion device and heat exchangers. Each of them should...
-
Physical properties and electronic structure of La3Co and La3Ni intermetallic superconductors
PublikacjaLa3Co and La3Ni are reported superconductors with transition temperatures of 4.5 and 6 K, respectively. Here, we reinvestigate the physical properties of these two intermetallic compounds with magnetic susceptibility χ, specific heat Cp and electrical resistivity ρ measurements down to 1.9 K. Although bulk superconductivity is confirmed in La3Co, as observed previously, only a trace of it is found in La3Ni, indicating that the...
-
Superconductivity in CaBi2
PublikacjaSuperconductivity is observed with critical temperature Tc = 2.0 K in self-flux-grown single crystals of CaBi2. This material adopts the ZrSi2 structure type with lattice parameters a = 4.696(1) Å, b = 17.081(2) Å and c = 4.611(1) Å. The crystals of CaBi2 were studied by means of magnetic susceptibility, specific heat and electrical resistivity measurements. The heat capacity jump at Tc is DC/gTc = 1.41, confirming bulk superconductivity;...
-
Heat recovery from the hybrid photovoltaic tile – experimental studies with the solar light simulator
PublikacjaConsidering the current development of micro-cogeneration energy sources, supported by the national prosumer policy and the act on the renewable energy sources, there is a great demand for the effective solar technologies. In this area, the photovoltaic cells with a combined conversion of the solar radiation energy into the electrical and thermal energy (PV/T cells) seem to be attractive. They are already widely available and treated...
-
An NO2 sensor based on WO3 thin films for automotive applications in the microwave frequency range
PublikacjaA microwave system dedicated to the detection of nitrogen dioxide in the harsh environment of the Norway highways is proposed. An optimized transmission line type of sensor coated with a tungsten trioxide thin film that changes its electrical properties under NO2 gas exposure is developed. The sensors' response (S) is given in °/GHz and it is calculated based on wideband measurements. The advantage of wideband measurements in comparison...
-
Analysis of an Energy Management System of a Small Plant Connected to the Rural Power System
PublikacjaThis paper presents the analysis of an energy management system (EMS) implemented to fulfill the requirements of a microgrid (MG) power supply owned by a small industrial company and connected to the rural power system. The main goal of this system is to ensure connection with the existing rural power system in terms of energy exchange, as well as to perform islanding mode operation of the microgrid based on the energy demand of...
-
Influence of the fragment size on the recycling process of thin-film modules based on CdTe
PublikacjaFor several years, the production of second generation cells (the so-called thin film), produced from amorphous silicon, cadmium telluride (CdTe) or copper indium (gallium) diselenide (CI(G)S), has been increasing. The total number of end-of-life panels by 2050 is expected to reach 9.57 million tonnes. They contain heavy metals that can be leached into the environment at the land field. The EU directive on waste electrical and...
-
Structure and transport properties of triple-conducting BaxSr1−xTi1−yFeyO3−δ oxides
PublikacjaIn this work, BaxSr1−xTi1−yFeyO3−δ perovskite-based mixed conducting ceramics (for x = 0, 0.2, 0.5 and y = 0.1, 0.8) were synthesized and studied. The structural analysis based on the X-ray diffraction results showed significant changes in the unit cell volume and Fe(Ti)–O distance as a function of Ba content. The morphology of the synthesized samples studied by means of scanning electron microscopy has shown different microstructures...
-
Ocena stanu chemicznego i zagrożeń wód podziemnych oraz powierzchniowych w rejonie Zalewu Wślanego
PublikacjaThe purpose of the research was to examine how factors such as land use and land management affect the quality of groundwater and surface water. These studies were possible thanks to funding from the IDUB Technetium Talent Management Grants project titled “Assessment of Anthropogenic Threat to Groundwater and Surface Water in the Region of the Vistula Lagoon”. The research area included a section of the Vistula Spit, ¯u³awy Wielkie...
-
Development of iron doped strontium titanates as oxygen electrode for solid oxide fuel cells
PublikacjaProducing efficient solid oxide fuel cells (SOFC) without the use of harmful elements is one of the current challenges. Increasing the safety of people and reducing production costs is possible, among others, thanks to the use of iron doped strontium titanates as porous oxygen electrodes. In this thesis, the results of research on iron doped strontium titanates as potential oxygen electrodes for SOFC are presented. The research...
-
Heterotrophic Anodic Denitrification in Microbial Fuel Cells
PublikacjaNowadays, pollution caused by energy production systems is a major environmental concern. Therefore, the development of sustainable energy sources is required. Amongst others, the microbial fuel cell (MFC) seems to be a possible solution because it can produce clean energy at the same time that waste is stabilized. Unfortunately, mainly due to industrial discharges, the wastes could contain nitrates, or nitrates precursors such...
-
A compartment model of alveolar–capillary oxygen diffusion with ventilation–perfusion gradient and dynamics of air transport through the respiratory tract
PublikacjaThis paper presents a model of alveolar–capillary oxygen diffusion with dynamics of air transport through the respiratory tract. For this purpose electrical model representing the respiratory tract mechanics and differentia equations representing oxygen membrane diffusion are combined. Relevant thermodynamic relations describing the mass of oxygen transported into the human body are proposed as the connection between these models,...
-
NEW SOLUTIONS FOR THE SOLAR CHARGE CONTROLLERS DESIGN FOR OBTAINING TRUE MPP IN PARTLY SHADED PV MODULES
PublikacjaSoft shading sources such as tree limbs, structural elements of buildings and chimneys, scatter and refract sunlight, significantly reducing the amount of radiation reaching the surface of the module. The hard shadings located directly on the surface (i.e. bird droppings, leaves, snow) tend to stop sunlight completely. These phenomena significantly affects the output characteristics of photovoltaic modules and often contribute...
-
The impedance of hydrogen oxidation reaction in a proton exchange membrane fuel cell in the presence of carbon monoxide in hydrogen stream
PublikacjaEvaluation of performance of a proton exchange membrane fuel cell, which is affected by carbon monoxide that pollutes the hydrogen stream, was presented. This influence was studied for carbon monoxide concentration of 125–325 ppb, which are close to values specified in ISO 14687:2019 standard. Performed studies provided crucial information for further development of fuel cell as an energy source for automotive application. Impedance...
-
Simple 60 GHz Switched Beam Antenna for 5G Millimeter-Wave Applications
PublikacjaA new 60 GHz band single-input switched beam antenna is proposed for the fifth-generation (5G) millimeter-wave network applications. The presented design is capable of electronically switching the main beam in two different directions via a proposed microstrip-line-to-slotline single-pole dual-throw (SPDT) switch based on commercially available p-i-n diodes. The antenna is fabricated in a low-cost printed circuit board process...
-
Correlation between partial inhibition of hydrogen evolution using thiourea and catalytic activity of AB5-type hydrogen storage alloy towards borohydride electrooxidation
PublikacjaDirect borohydride fuel cells (DBFCs) are devices which directly convert the chemical energy stored in the borohydride ion and oxidant into electrical energy as a result of redox reactions. Unfortunately, a significant amount of fuel is lost as a result of the undesirable hydrolysis reaction. The selection of an efficient borohydride hydrolysis inhibitor requires detailed knowledge regarding the interaction mechanism between the...
-
Ion conduction in beryllium-alumino-silicate glasses doped with sodium or sodium and lithium ions
PublikacjaElectrical properties of beryllium-alumino-silicate glasses containing sodium ions or sodium and lithium ions were studied with impedance spectroscopy technique over a frequency range from 10 mHz to 1 MHz and at temperature range from 213 to 473 K. The frequency- and temperature-dependent conductivity spectra of individual single alkali glasses were superimposed by means of the Summerfield scaling. Mixed-alkali glasses do not overlap...
-
New ceramic materials derived from pyrolyzed poly(1,2-dimethylsilazane) and starch as a potential anode for Li-ion batteries
PublikacjaNewmaterialswere obtained by pyrolysis of starch (S) and poly(1,2-dimethylsilazane) (PSN) (weight ratio: PSN/S 30/70) at temperature a) 500 °C, b) 700 °C and c) 900 °C. Ceramic materials were characterized by infrared spectroscopy, TGA, Raman spectroscopy and SEM. New Si\O and shifted Si\C stretching vibration modes emerged confirming direct interaction between silicon originating fromsilazane and oxygen coming fromstarch. The...
-
A gap waveguide-based mechanically reconfigurable phase shifter for high-power Ku-band applications
PublikacjaThis paper presents a novel design of a low-loss, reconfgurable broadband phase shifter based on groove gap waveguide (GGW) technology. The proposed phase shifter consists of a folded GGW and three bends with a few pins forming the GGW and one bend attached to a movable plate. This movable plate allows for adjustments to the folded waveguide length, consequently altering the phase of electromagnetic waves. The advantage of GGW...
-
The Design of Cavity Resonators and Microwave Filters Applying Shape Deformation Techniques
PublikacjaThis article introduces shape deformation as a new approach to the computer-aided design (CAD) of high-frequency components. We show that geometry deformation opens up new design possibilities and offers additional degrees of freedom in the 3-D modeling of microwave structures. Such design flexibility is highly desirable if the full potential of additive manufacturing (AM) is to be exploited in the fabrication of RF and microwave...
-
Preparation and Characterization of Diamond-like Carbon Coatings for Biomedical Applications—A Review
PublikacjaDiamond-like carbon (DLC) films are generally used in biomedical applications, mainly because of their tribological and chemical properties that prevent the release of substrate ions, extend the life cycle of the material, and promote cell growth. The unique properties of the coating depend on the ratio of the sp3/sp2 phases, where the sp2 phase provides coatings with a low coefficient of friction and good electrical conductivity,...
-
Understanding the Dominant Physics Mechanisms on the p-i-n Perovskite Solar Cells Fabricated by Scalable Slot-Die Coating Process in Ambient Air
PublikacjaPerovskite solar cells (PSC) are emerging technologies that have shown continuous improvement in power conversion efficiency (PCE) and stability. However, a very important aspect that has been seldom considered is the reproducibility of PCE of PSC devices. It is possible to achieve PCE from 10.21% to 17.05% using scalable slot-die-coating technique. However, a spatial distribution of performance is clearly observed for device samples...
-
Enhanced Mechanical and Electromechanical Properties of Compositionally Complex Zirconia Zr1–x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2−δ Ceramics
PublikacjaCompositionally complex oxides (CCOs) or high-entropy oxides (HEOs) are new multi-element oxides with unexplored physical and functional properties. In this work, we report fluorite structure derived compositionally complex zirconia with composition Zr1- x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2-δ (x = 0.1 and 0.2) synthesized in solid-state reaction route and sintered via hot pressing at 1350 °C. We explore the evolution of these oxides'...
-
Complex Corrosion Monitoring System for Crude Distillation Unit in Form of Neutral Network
PublikacjaComplex and successful corrosion monitoring of refinery processes can significantly reduce material losses and failure risk. The developed corrosion monitoring system is based on online ultrasonic sensors, ER (electrical resistance) probes, gravimetric method and multipoint analytical analysis of chemical composition of the fluids. Additional online LPR (linear polarization resistance) sensors controlling corrosiveness of sour...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublikacjaThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
Low-Dimensional Magnetic Semimetal Cr0.65Al1.35Se3
PublikacjaWhile exploring novel magnetic semiconductors, the new phase Cr0.65Al1.35Se3 was discovered and characterized by both structural and physical properties. Cr0.65Al1.35Se3 was found to crystallize into orthorhombic CrGeTe3-type structure with space group Pnma (no. 62). Vacancies and mixed occupancies were tested, and the results show that one of the 4c sites accommodates a mixture of Cr and Al atoms, while the other 4c site is fully...
-
Video traffic data - Interchange Sulno (S1-94), Poland
Dane BadawczeThe data includes video traffic data registered with 8 video cameras at weaving area (weaving section type A) of the Sulno interchange within S1 expressway in Poland (interchange of expressway S1 and national road 94), located in the Silesian Agglomeration. The data covers the two days: 12.09.2017 (expressway S1) and 13.09.2017 (road 94).
-
Modeling of Electrified Transportation Systems Featuring Multiple Vehicles and Complex Power Supply Layout
PublikacjaThe paper proposes a novel approach to modeling electrified transportation systems. The proposed solution reflects the mechanical dynamics of vehicles as well as the distribution and losses of electric supply. Moreover, energy conversion losses between the mechanical and electrical subsystems and their bilateral influences are included. Such a complete model makes it possible to replicate, e.g., the impact of voltage drops on vehicle...
-
Optimization of Train Energy Cooperation Using Scheduled Service Time Reserve
PublikacjaThe main aim of the paper was to develop an innovative approach to the preliminary estimation possibility of train energy cooperation based on data from timetables, without traction calculations. The article points out the need to strive for sustainable and environmentally friendly transport. It was pointed out that rail transport using electric traction is one of the more ecological branches of transport. It also offers a number...
-
Porosity and shape of airborne wear microparticles generated by sliding contact between a low-metallic friction material and a cast iron
PublikacjaThe wear of brakes in transport vehicles is one of the main anthropogenic sources of airborne particulate matter in urban environments. The present study deals with the characterisation of airborne wear microparticles from a low-metallic friction material / cast iron pair used in car brakes. Particles were generated by a pin-on-disc machine in a sealed chamber at sliding velocity of 1.3 m/s and contact pressure of 1.5 MPa. They...
-
Family Tree for Aqueous Organic Redox Couples for Redox Flow Battery Electrolytes: A Conceptual Review
PublikacjaRedox flow batteries (RFBs) are an increasingly attractive option for renewable energy storage, thus providing flexibility for the supply of electrical energy. In recent years, research in this type of battery storage has been shifted from metal-ion based electrolytes to soluble organic redox-active compounds. Aqueous-based organic electrolytes are considered as more promising electrolytes to achieve “green”, safe, and low-cost...
-
Physical and sealing properties of BaO–Al2O3–SiO2–CaO–V2O5 glasses for solid oxide fuel cell applications
PublikacjaIn this study, the properties of BaO–Al2O3–SiO2 (SAB) glasses incorporated with CaO and V2O5 as the network modifier and additive, respectively, are evaluated. The electrical resistivities of the glasses decrease upon the addition of CaO but increase upon increasing their V2O5 content because the V5+ species lower the ionic mobility of the glasses. The addition of V2O5 improves the wettability of the glasses on the Crofer 22 APU...
-
Synthesis and Characterization of Poly(zwitterionic) Structures for Energy Conversion and Storage
PublikacjaZwitterions are unique class of molecules that possess two functional groups bearing electric charges, one positive and second negative. This setup results in peculiar properties such as high water retention and anti-fouling capability. Therefore, zwitterionic coatings and gels are commonly applied in e.g. biosensing and bioelectronic devices. Despite those applications, there are other perspectives for zwitterionic materials....
-
Superconductivity in LiGa2Ir Heusler type compound with VEC = 16
PublikacjaPolycrystalline LiGa2Ir has been prepared by a solid state reaction method. A Rietveld refnement of powder x-ray difraction data confrms a previously reported Heusler-type crystal structure (space group Fm-3m, No. 225) with lattice parameter a= 6.0322(1) Å. The normal and superconducting state properties were studied by magnetic susceptibility, heat capacity, and electrical resistivity techniques. A bulk superconductivity with...
-
Assessment of Fuel Cells’ State of Health by Low-Frequency Noise Measurements
PublikacjaWe proposed applying low-frequency (flicker) noise in proton-exchange membrane fuel cells under selected loads to assess their state of health. The measurement set-up comprised a precise data acquisition board and was able to record the DC voltage and its random component at the output. The set-up estimated the voltage noise power spectral density at frequencies up to a few hundred mHz. We observed the evolution of the electrical...
-
Experimental research on helical coil biomass boiler with oil as a heating fluid
PublikacjaThis paper presents an experimental research of helical coil biomass boiler with thermal oil heating agent. Heat exchanger consists of two coaxial helical coils swept by the flue gases. The burner is a single vertical retort connected to the fuel tank (wooden pellets). The boiler is a part of micro-power plant in which the heat from the boiler is exchanged with low-boiling HFE7100 to produce steam for a custom steam turbine. The...
-
Water Solubilization Using Nonionic Surfactants from Renewable Sources in Microemulsion Systems
PublikacjaIn this study the effect of temperature, NaCl andoils (hydrocarbons: C8-C16) on the formation and solubilizationcapacity of the systems of oil/monoacylglycerols(MAG):ethoxylated fatty alcohols (CEO20)/propylene glycol(PG)/water was investigated. The effects of the surfactantmixture on the phase behavior and the concentration ofwater or oil in the systems were studied at three temperatures(50, 55, 60 C) and with varied NaCl solutions...
-
Storage of High-Strength Steel Flux-Cored Welding Wires in Urbanized Areas
PublikacjaThe condition of the consumables is a key factor determining the waste reduction in the welding processes and the quality of the welded joint. The paper presents the results of tests of four types of fux-cored wires dedicated for welding high-strength steels, stored for 1 month and 6 months in Poland in two urbanized areas: in a large seaside city (Gdańsk) and in Warsaw, located in the center of the country. The wires were subjected...
-
Band Gap Engineering toward Semimetallic Character of Quinone-Rich Polydopamine
PublikacjaSemiconductor|melanin interfaces have received increasingly more attention in the fields of photocatalysis and applied electrochemistry because of their facile synthesis, unique electrical properties, and strong capability toward photosensitization. In this work, we describe the electropolymerization of quinone-rich polydopamine (PDA) on the surface of hydrogenated TiO2 nanotubes with enhanced photoactivity in the visible spectrum....
-
The use of LiFePO4 technology in autonomous PV systems
PublikacjaBattery manufacturing based on the flow of lithium ions is currently the fastest growing and the most promising technology. It is used in many applications - from the smallest electronic devices to the large-scale energy trays. However, in the PV systems lead-acid batteries are still the most commonly used. As they are much cheaper they also come with a number of significant disadvantages. It is anticipated that they will be replaced...
-
Wavelet transform-based approach to defect identification in railway carbon contact strips.
PublikacjaPantographs of electric rail vehicles are fitted with carbon contact strips, which slide along the contact wire of catenary to provide constant electrical contact. Contact strips are exposed to wear and damages. Using damaged contact strips significantly increases the risk of catenary rupture. Therefore, their technical condition has to be inspected frequently. In previous work a 3D laser scanning system was proposed for recording...
-
DESIGN ANALYSIS OF HYBRID GAS TURBINE - FUEL CELL POWER PLANT IN STATIONARY AND MARINE APPLICATIONS
PublikacjaThe paper concerns design analysis of a hybrid gas turbine power plant with a fuel cell (stack). The aim of this work was to find the most favorable variant of the medium capacity (approximately 50 MW) hybrid system. In the article, computational analysis of two variants of such a system was carried out. The analysis let to calculate capacity, efficiency of both variants and other parameters like flu gas temperature. The paper...
-
Effect of Cr and Mn doping on ferroelectric and dielectric properties of Li1.72Na0.28Ge4O9 single crystals
PublikacjaLi1.72Na0.28Ge4O9 single crystals pure and slightly doped with chromium and manganese, obtained by Czochralski growth, were investigated for their ferroelectric and dielectric properties. The change in stoichometry of Li2− x Na x Ge4O9 (x = 0.28) crystals doped with Cr and Mn (0.1 mol.%) had an influence on the value of ferroelectric-to-paraelectric phase transition temperature, T c. The applied doping affects the T c value by...
-
Size reduction of ultra-wideband antennas with efficiency and matching constraints
PublikacjaAntenna design is a multifaceted task that involves handling of various performance figures concerning both electrical performance of the structure as well as its geometry. Simultaneous control of several objectives through rigorous optimization is very challenging and virtually impossible through conventional approaches such as parameter sweeping. In this work, we investigate size reduction of ultra‐wideband antenna structures...
-
Synthesis and physical properties of the 10.6 K ferromagnet NdIr3
PublikacjaThe magnetic, transport, and thermodynamic properties of NdIr3 are reported. Its PuNi3-type crystal structure (space group R−3m), with lattice parameters a= 5.3262(1)Å and c=26.2218(3)Å, was confirmed by powder x-ray diffraction. Our measurements indicate that NdIr3 exhibits a previously unreported paramagnetic to ferromagnetic phase transition below TC=10.6 K(determined by using the Arrott plot). The magnetic susceptibility obeys...
-
Structural and physical characterization of NpPt2In7
PublikacjaA new neptunium intermetallic compound, NpPt2In7, has been synthesized in polycrystalline form and characterized by several macroscopic techniques. A Rietveld analysis of its powder x-ray diffraction pattern shows that NpPt2In7 crystallizes in a tetragonal lattice with I4/mmm symmetry and lattice parameters a = 4.58471(3) Å, c = 21.5065(3) Å. Magnetic susceptibility, electrical resistivity, Hall effect, and heat capacity measurements indicate...
-
Smart Weighing Scale with Feet-Sampled ECG
PublikacjaIn a smart home, health and well-being monitoring systems could be embedded in everyday devices providing a pervasive care. A home bathroom scale is an example of such a device, typically used to measure body weight and very often its composition (e.g. body water/fat percentage). In this paper, we analyzed a potential use of the bathroom scale to measure electrocardiogram (ECG) from electrodes located on the scale's tile. In particular...
-
Assembly of 1D Granular Structures from Sulfonated Polystyrene Microparticles
PublikacjaBeing able to systematically modify the electric properties of nano- and microparticles opens up new possibilities for the bottom-up fabrication of advanced materials such as the fabrication of one-dimensional (1D) colloidal and granular materials. Fabricating 1D structures from individual particles offers plenty of applications ranging from electronic sensors and photovoltaics to artificial flagella for hydrodynamic propulsion....
-
In situ study of a composition of outlet gases from biogas fuelled Solid Oxide Fuel Cell performed by the Fourier Transform Infrared Spectroscopy
PublikacjaThe purpose of this study was to develop a method and software based on the Fourier Transform Infrared Spectroscopy for the in-situ, quantitative analysis of the composition of outlet gases from Solid Oxide Fuel Cell (SOFC). The calibration procedure performed at the beginning of the experiment indicated a polynomial dependence between the concentration of a calibrating gas (CO, CO2, CH4) and the corresponding integrated absorbance in...
-
Atomic-Scale Finite-Element Modeling of Elastic Mechanical Anisotropy in Finite-Sized Strained Phosphorene Nanoribbons
PublikacjaNanoribbons are crucial nanostructures due to their superior mechanical and electrical properties. This paper is devoted to hybrid studies of the elastic mechanical anisotropy of phosphorene nanoribbons whose edges connect the terminals of devices such as bridges. Fundamental mechanical properties, including Young’s modulus, Poisson’s ratio, and density, were estimated from first-principles calculations for 1-layer, 3-layer, and...