wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: DIELECTRIC SUBSTRATE, LOW-LOSS SUBSTRATE, DIELECTRIC CONSTANT, DIELECTRIC MEASUREMENT
-
Novel Low-Loss Substrates for 5G Applications
PublikacjaThis paper presents a feasibility study of a new type of microwave low-loss dielectric substrates for 5G network applications. The new substrate materials are composites of polypropylene and high-dielectric-constant micro-ceramics. This combination is expected to form a very low-loss dielectric material at low fabrication cost. Two substrate samples with different dielectric properties are fabricated and their characteristics at...
-
Low-cost and reliable geometry scaling of compact microstrip couplers with respect to operating frequency, power split ratio, and dielectric substrate parameters
PublikacjaA technique for rapid re-design of miniaturised microstrip couplers with respect to operating conditions as well as material parameters of the dielectric substrate is proposed. The dimension scaling process is based on a set of pre-optimised reference designs, obtained for an equivalent circuit model of the coupler at hand. The reference designs are utilised to construct an inverse surrogate model which – upon suitable correction...
-
Coplanar Waveguide-Fed Broadband Microwave Devices with (or without) a Thin Dielectric Substrate for Use in Flexible Electronic Systems
PublikacjaTwo examples of microwave devices, fed by a coplanar waveguide and realized on a thin substrate (or without such a substrate), are employed to investigate the influence of devices’ curvatures and the proximity of different materials on their parameters. To perform the tests, a broadband antenna and a low-pass filter are chosen. A feeding coplanar waveguide is realized on a dielectric material brick attached to an SMA connector...
-
Modulation of dielectric properties in low-loss polypropylene-based composites at GHz frequencies: theory and experiment
PublikacjaPolymer composites with high dielectric constant and low loss tangent are highly regarded as substrates for modern high-speed electronics. In this work, we analyze the high-frequency dielectric properties of two types of composites based on polypropylene infused with high-dielectric-constant microparticles. Two types of fillers are used: commercial ceramics or titanium oxide ( TiO2) with different concentrations. The key observation...
-
Polyurethane glycolysate from industrial waste recycling to develop low dielectric constant, thermally stable materials suitable for the electronics
PublikacjaWe are utilizing a new method to improve the dielectric properties of a conventional polymer using a recycled polymer product. The polyurethane foams are recycled by glycolysis process and the derived material was applied to improve the dielectric properties of the brittle DGEBA epoxy resin. Two main parameters that determine the applicability of the material as a dielectric (the dielectric constant and dielectric loss), were studied...
-
Planar Microwave Bragg Reflector Resonant Dielectric Sensor
PublikacjaIn this paper, a periodic structure is used to design a microwave Bragg reflector with the help of hexagonal lattice, which provides a 5 GHz wide stopband between the low-pass band with cut-off frequency 2.6 GHz and the bandpass response with start and stop frequency 7.8 GHz and 10.5 GHz, respectively. A defect in lattice allows passing a narrowband signal at 6 GHz which is found, from the dispersion relation, to be in the region...
-
New Complementary Resonator for Permittivity- and Thickness-Based Dielectric Characterization
PublikacjaThe design of high-performance complementary meta-resonators for microwave sensors featur-ing high sensitivity and consistent evaluation of dielectric materials is challenging. This paper presents the design and implementation of a novel complementary resonator with high sensi-tivity for dielectric substrate characterization based on permittivity and thickness. A comple-mentary crossed arrow resonator (CCAR) is proposed and integrated...
-
Novel Complementary Resonator for Dielectric Characterization of Substrates Based on Permittivity and Thickness
PublikacjaThis paper presents a novel complementary resonator featuring high sensitivity, low fabrication cost, and improved performance. The proposed structure consists of a complementary concentric square and circular ring resonator (CCSCRR) with multiple splits to enhance the inductance of the resonator. The proposed CCSCRR is coupled to a microstrip transmission line with an impedance of fifty ohms to create a high-sensitivity sensor....
-
Resonant Frequencies in Microstrip Structure with Omega Medium Substrate
PublikacjaThe paper presents the research on a rectangular microstrip structure with multilayer substrate containing dielectric and omega medium layers. The effect of pseudochiral medium layer location in the substrate and its thickness on the resonant frequency of the rectangular microstrip structure is investigated. The numerical analysis of investigated structures is based on expansion of electric and magnetic fields. Utilizing the continuity...
-
Influence of Dielectric Overlay Permittivity on Size and Performance of Miniaturized ESPAR Antenna
PublikacjaIn this paper, influence of dielectric overlay permittivity on miniaturized ESPAR antenna parameters is presented. ESPAR antenna is a low-cost and energy-efficient way to implement beam steering capability to a node and improve network performance. The antenna size reduction is obtained by embedding its active and passive elements in ABS based materials of relative permittivity equal to 4, 5.5 and 7.5 in order to achieve network...
-
Reliable low-cost surrogate modeling and design optimisation of antennas using implicit space mapping with substrate segmentation
PublikacjaAbstract: In this work, a reliable methodology for fast simulation-driven design optimisation of antenna structures is proposed. The authors’ approach exploits implicit space mapping (ISM) technology. To adopt it for handling antenna structures, they introduce substrate segmentation with separate dielectric permittivity value assigned for each segment as ISM preassigned parameters. At the same time, the coarse model for space mapping...
-
Pin-on-Substrate Gap Waveguide: An Extremely Low-Cost Realization of High-Performance Gap Waveguide Components
PublikacjaConsidering the limitations of currently available technologies for the realization of microwave components and antennas, a trade-off between different factors including the efficiency and fabrication cost is required. The main objective of this letter is to propose a novel method for the realization of gap waveguides (GWGs) that take advantage of conventional PCB fabrication technology, thus are low cost and light weight. Moreover,...
-
Resonance in Rectangular Microstrip Structure Loaded with a Pseudochiral Medium Layer
PublikacjaA rectangular microstrip structure with multilayer substrate containing dielectric and pseudochiral medium layers is studied in this paper. The effect of Omega medium layer location in the substrate and its thickness on the complex resonant frequency of the rectangular microstrip structure is investigated.
-
Comprehensive dimension scaling of multi-band antennas for operating frequencies and substrate parameters
PublikacjaIn this paper, low-cost and comprehensive redesign of multi-band antennas with respect to the operating frequencies and material parameters of the substrate is presented. Our approach exploits an inverse surrogate model identified based on a set of reference designs optimized at the level of coarse-discretization EM simulations of the antenna at hand. An iterative correction procedure is also implemented to account for the initial...
-
Novel Complementary Multiple Concentric Split Ring Resonator for Reliable Characterization of Dielectric Substrates with High Sensitivity
PublikacjaAccurate characterization of dielectric substrates with high sensitivity remains an important challenge in a variety of industrial applications. This paper proposes an innovative strategy to address this challenge by developing and optimizing a unique Complementary Multiple Concentric Split Ring Resonator (CMC-SRR). The major goal is to propose a sensor design with increased sensitivity and reliability for dielectric characterization....
-
Rapid redesign of multiband antennas with respect to operating conditions and material parameters of substrate
PublikacjaThis work addresses geometry parameter scaling of multi-band antennas for Internet of Things applications. The presented approach is comprehensive and permits re-design of the structure with respect to both the operating frequencies and material parameters of the dielectric substrate. A two-step procedure is developed with the initial design obtained from an inverse surrogate model constructed using a set of appropriately prepared...
-
Dielectric Properties of BiNbO<sub>4</sub>-Based Ceramic-Polymer Composites with 0-3 Connectivity
PublikacjaIn the present study two-phase BiNbO4//PVDF composites with 0-3 connectivity were studied by impedance spectroscopy within the frequency range Δν=100Hz-1MHz at room temperature. Polyvinylidene fluoride (PVDF) acted as a matrix whereas bismuth niobate (BiNbO4) powder acted as a dispersed phase. The volume fraction of the ceramic phase was cV=2, 4, 6, 8, 10, 16 and 20vol%. Analysis of the impedance data registered for composites...
-
Effect of Cr and Mn doping on ferroelectric and dielectric properties of Li1.72Na0.28Ge4O9 single crystals
PublikacjaLi1.72Na0.28Ge4O9 single crystals pure and slightly doped with chromium and manganese, obtained by Czochralski growth, were investigated for their ferroelectric and dielectric properties. The change in stoichometry of Li2− x Na x Ge4O9 (x = 0.28) crystals doped with Cr and Mn (0.1 mol.%) had an influence on the value of ferroelectric-to-paraelectric phase transition temperature, T c. The applied doping affects the T c value by...
-
Novel MNZ-type microwave sensor for testing magnetodielectric materials
PublikacjaA novel microwave sensor with the mu-near-zero (MNZ) property is proposed for testing magnetodielectric material at 4.5 GHz. The sensor has a double-layer design consisting of a microstrip line and a metal strip with vias on layers 1 and 2, respectively. The proposed sensor can detect a unit change in relative permittivity and relative permeability with a difference in the operating frequency of 45 MHz and 78 MHz, respectively....
-
A Comprehensive Survey on Antennas On-Chip Based on Metamaterial, Metasurface, and Substrate Integrated Waveguide Principles for Millimeter-Waves and Terahertz Integrated Circuits and Systems
PublikacjaAntennas on-chip are a particular type of radiating elements valued for their small footprint. They are most commonly integrated in circuit boards to electromagnetically interface free space, which is necessary for wireless communications. Antennas on-chip radiate and receive electromagnetic (EM) energy as any conventional antennas, but what distinguishes them is their miniaturized size. This means they can be integrated inside...
-
Near Field Coupled Wireless Microwave Sensor
PublikacjaThis paper presents a wireless planar microwave sensor operating at industrial scientific and medical (ISM) frequency for the detection of dielectric materials. The microwave sensor consists of a reader (ground defected microstrip coupled line) and a passive tag where a complementary split-ring resonator (CSRR) is made on the commercially available copper-foil. The CSRR is a peel-off type tag that is excited using the near field...
-
Microwave Characterization of Dielectric Sheets in a Plano-Concave Fabry-Perot Open Resonator
PublikacjaDespite its long history, a double-concave (DC) Fabry-Perot open resonator (FPOR) has recently gained popularity in the characterization of dielectrics in the 20–110 GHz range, mainly due to such novel accomplishments as full automation of the measurement process and the development of even ore accurate and computationally efficient electromagnetic model. However, it has been discovered that such a DC resonator suffers from unwanted...
-
An Analysis of Elliptical-Rectangular Patch Structure on Multilayer Elliptic Cylinders
PublikacjaThe resonance frequency problem of an ellipticalrectangular patch mounted on multilayered dielectric coated elliptic conducting cylinder, is investigated in this paper. A fullwave analysis and a moment-method calculation are employed. The analysis is carried out considering the expansion of the field as a series of Mathieu functions. An additional theorem for Mathieu functions is utilized to investigate the non-confocal ellipse...
-
Właściwości elektryczne szkło-ceramiki zawierającej ferroelektryczną fazę BiV
PublikacjaKompozyty szklano - ceramiczne zawierające nanokryształy posiadają właściwości fizyczne, które nie są możliwe do uzyskania w innych materiałach. Dzięki możliwości wytworzenia szkło - ceramik posiadających kryształy o różnej wielkości (nano, mikro...) i różnorodnego typu, można w istotny sposób kontrolować właściwości elektryczne takich materiałów. Stała dielektryczna faz ferroelektrycznych jest bardzo wrażliwa na zmiany rozmiarów...
-
Assembly of 1D Granular Structures from Sulfonated Polystyrene Microparticles
PublikacjaBeing able to systematically modify the electric properties of nano- and microparticles opens up new possibilities for the bottom-up fabrication of advanced materials such as the fabrication of one-dimensional (1D) colloidal and granular materials. Fabricating 1D structures from individual particles offers plenty of applications ranging from electronic sensors and photovoltaics to artificial flagella for hydrodynamic propulsion....
-
Extending the Frequency Limit of Microstrip-Coupled CSRR Using Asymmetry
PublikacjaAbstract— This article explains the frequency limitation in designing microstrip circuits based on a complementary split-ring resonator (CSRR) and reports a novel technique for increasing its operating frequency, which makes the CSRR suitable for high-frequency applications. This study helps in synthesizing the dimensions of symmetric CSRR (SCSRR) and asymmetric CSRR (ACSRR) circuits, which shows the applicability of the proposed...
-
Microfluidically Frequency-Reconfigurable Self-Quadruplexing Antenna Based on Substrate Integrated Square-Cavity
PublikacjaIn this article, a novel concept of self-quadruplexing tunable antenna (SQTA) enabled by microfluidic channels is investigated. The operating channels are either filled with air or dielectric liquids to enable frequency tunability. The proposed SQTA is implemented on the substrate-integrated square-cavity (SISC). A swastika-shaped slot is milled on the top-surface of the SISC to create four quarter-mode resonators. The resonators...
-
Frequency Selective Surface Based MIMO Antenna Array for 5G Millimeter-Wave Applications
PublikacjaAbstract: In this paper a radiating element consisting of a modified circular patch is proposed for MIMO arrays for 5G millimeter-wave applications. The radiating elements in the proposed 2×2 MIMO antenna array are orthogonally configured relative to each other to mitigate mutual coupling that would otherwise degrade the performance of the MIMO system. The MIMO array was fabri-cated on Rogers RT/Duroid high frequency substrate...
-
New plasmonic platform for enhanced luminescence of Valrubicin
PublikacjaLuminescence enhanced by new structure of plasmonic platform with aluminum oxide (Al2O3) buffer layer deposited on gold nanostructures is investigated. Regularly distributed gold nanostructures of average dimension of 50 nm formed the active part of plasmonic platforms. They were manufactured on Corning 1737 glass substrate by melting of gold thin film. The nanostructures were coated by dielectric Al2O3 thin film with thickness...
-
Accelerated Re-Design of Antenna Structures Using Sensitivity-Based Inverse Surrogates
PublikacjaThe paper proposes a novel framework for accelerated re-design (dimension scaling) of antenna structures using inverse surrogates. The major contribution of the work is a sensitivity-based model identification procedure, which permits a significant reduction of the number of reference designs required to render the surrogate. Rigorous formulation of the approach is supplemented by its comprehensive numerical validation using a...
-
Microfluidically Frequency-Reconfigurable Compact Self-Quadruplexing Tunable Antenna with High Isolation Based on Substrate Integrated Waveguide
PublikacjaThis communication presents a novel concept of microfluidically frequency-reconfigurable self-quadruplexing tunable antenna for quad-band applications. At the initial design stage, a substrate-integrated square cavity is divided into four unequal quarter-mode cavity resonators by inserting an X-shaped slot on the top surface of the cavity. Applying four 50-ohm microstrip feed-lines to these four quarter-mode cavity resonators enables...
-
Kriging metamodels and design re‐utilization for fast parameter tuning of antenna structures
PublikacjaThe paper addresses the problem of computationally efficient electromagnetic (EM)‐driven design closure of antenna structures. The foundations of the presented approach are fast kriging interpolation metamodels, utilized for two purposes: (a) producing a good starting point for further parameter tuning, and (b) yielding a reasonable Jacobian matrix estimate to jump‐start the optimization procedure. The models are rendered using...
-
Tuning of the plasmon resonance location in Au nanostructures coated with a ultrathin film of Al2O3 – Optical measurements and FDTD simulations
PublikacjaThe Au nanostructures have been coated with an ultra-thin films of amorphous aluminium oxide. Optical absorption spectra show the influence of the thickness of Al2O3 on plasmon resonance wavelength. The observed red-shift of the resonance location with the increase of the thickness of the Al2O3 film, can be explained by the change in the dielectric function of this film. It allows control of the optical spectra of the coated particles....
-
TEM and EDX study of the Al2O3 ultra thin films
Dane BadawczeThe ultra-thin layers of Al2O3 were deposited on a silicon substrates. The method of atomic layer deposition (Beneq TFS 200 ALD system) was chosen as the proper method of dielectric layer deposition. This method provides precise thickness control down to a single atomic layer. The precursors used were trimethylaluminum (Sigma-Aldrich) and purified water....
-
An Innovative Antenna Array with High Inter Element Isolation for Sub-6 GHz 5G MIMO Communication Systems
PublikacjaA novel technique is shown to improve the isolation between radiators in antenna arrays. The proposed technique suppresses the surface-wave propagation and reduces substrate loss thereby enhancing the overall performance of the array. This is achieved without affecting the antenna’s footprint. The proposed approach is demonstrated on a four-element array for 5G MIMO applications. Each radiating element in the array is constituted...
-
Simplified Approach for Broadband RF Testing of Low Loss Magneto-Dielectric Samples
PublikacjaIn this paper, an attractive measurement techniqueis proposed to retrieve the broadband permittivity and permeabil-ity of the magneto-dielectric materials. The proposed techniqueis quite novel which mitigates the major problems associatedwith the conventional broadband RF material characterizationtechniques such as numerical instability and phase uncertaintywhen the length of the sample exceeds...
-
High gain/bandwidth off‑chip antenna loaded with metamaterial unit‑cell impedance matching circuit for sub‑terahertz near‑field electronic systems
PublikacjaAn innovative off-chip antenna (OCA) is presented that exhibits high gain and efficiency performance at the terahertz (THz) band and has a wide operational bandwidth. The proposed OCA is implemented on stacked silicon layers and consists of an open circuit meandering line. It is shown that by loading the antenna with an array of subwavelength circular dielectric slots and terminating it with a metamaterial unit cell, its impedance...
-
Broadband Compact Single-Layer Magic-T Junction with Separation of DC Signals between All Ports
PublikacjaA novel structure for a four-port microstrip magic-T junction is presented. The device is composed of microstrip and slotline circuits etched onto two sides of a dielectric substrate. The device is extremely compact and occupies an area more than three times smaller than similar structures recently reported in the literature. The novelty of the device lies in the use of microstrip/slotline transitions for both input ports: summation...
-
Metal-Organic Framework (MOF)/Epoxy Coatings: A Review
PublikacjaEpoxy coatings are developing fast in order to meet the requirements of advanced materials and systems. Progress in nanomaterial science and technology has opened a new era of engineering for tailoring the bulk and surface properties of organic coatings, e.g., adhesion to the substrate, anti-corrosion, mechanical, flame-retardant, and self-healing characteristics. Metal-organic frameworks (MOFs), a subclass of coordinative polymers...
-
On Reduced-Cost Design-Oriented Constrained Surrogate Modeling of Antenna Structures
PublikacjaDesign of contemporary antenna structures heavily relies on full-wave electromagnetic (EM) simulation models. Such models are essential to ensure reliability of evaluating antenna characteristics, yet, they are computationally expensive and therefore unsuitable for handling tasks that require multiple analyses, e.g., parametric optimization. The cost issue can be alleviated by using fast surrogate models. Conventional data-driven...
-
Effective dielectric constant of two phase dielectric systems
PublikacjaW tym artykule model brick-layer ścianie został rozszerzony na dwufazowe systemy perkolacyjne. Porównano wyniki obliczeń z danymi eksperymentalnymi. Stałe dielektryczne obu faz oraz próg perkolacji pozwala na wyznaczenie efektywnej stałej dielektrycznej systemu dwufazowego.
-
Near-Field Wireless Sensing of Plastics and Papers Using Frugal Peel-Off Passive Tag
PublikacjaThis article presents a novel frugal approach of testing plastics and papers using a near-field microwave sensing technique with a peel-off tag. The proposed sensing technique involves two electrical entities: the sensor, which may be regarded as a reader, and a disposable tag. The reader is a modified design of a gap-coupled microstrip line (GCML) sensor, while the passive tag is a standard double-ring complementary split-ring...
-
Fabrication of La-Doped Bi4Ti3O12 Ceramics
PublikacjaLa-modified Bi4Ti3O12 is a typical ferroelectric, piezoelectric and electro-optic material, having relatively low coercive field, low dielectric constant, high Curie temperature and high breakdown strength. Goal of the present research was to apply mixed oxide method for fabrication of BiTLax ceramics, study its chemical composition, crystalline structure and microstructure. The compound BiTLax for x=0, 0.25, 0.5, 0.75 ceramic...
-
Nanostructures fabrication with use of electrical AFM litography
Dane BadawczeIn the last 10 years, one of the nanotechnological trends has been observed, consisting in the development of new variants of computer memory systems with high capacity and speed of access, using quantum dots. One of the techniques for creating nanodots and other nanostructures is based on the use of an atomic force microscope acting as a lithographic...
-
A Microwave Sensor with Operating Band Selection to Detect Rotation and Proximity in the Rapid Prototyping Industry
PublikacjaThis paper presents a novel sensor for detecting and measuring angular rotation and proximity, intended for rapid prototyping machines. The sensor is based on a complementary split-ring resonator (CSRR) driven by a conductor-backed coplanar waveguide. The sensor has a planar topology, which makes it simple and cost-effective to produce and accurate in measuring both physical quantities. The sensor has two components, a rotor, and...
-
A Review of Hyperelastic Constitutive Models for Dielectric Elastomers
PublikacjaDielectric elastomers are smart materials that are essential components in soft systems and structures. The core element of a dielectric elastomer is soft matter, which is mainly rubber-like and elastomeric. These soft materials show a nonlinear behaviour and have a nonlinear strain-stress curve. The best candidates for modelling the nonlinear behaviour of such materials are hyperelastic strain energy functions. Hyperelastic functions...
-
Tunable Dielectric Switching of (Quinuclidinium)[MnCl4] Hybrid Compounds
PublikacjaInorganic−organic hybrid QMnCl (Q = quinuclidinium) crystals were synthesized and characterized. The X-ray and variable-temperature IR/Raman analysis demonstrate that the crystals undergo a reversible structural phase transition, which originates from an order−disorder process and is related to the dynamics of the organic Q cation. Dielectric function measurements disclose a switchability between low (“OFF”) and high (“ON”) dielectric...
-
Low temperature broad band dielectric spectroscopy of multiferroic Bi6Fe2Ti3O18 ceramics
PublikacjaIn the present research the tool of broadband dielectric spectroscopy was utilized to characterize dielectric behavior of Bi6Fe2Ti3O18 (BFTO) Aurivillius-type multiferroic ceramics. Dielectric response of BFTO ceramics was studied in the frequency domain (Δν=0.1Hz – 10MHz) within the temperature range ΔT=-100°C – 200°C. The Kramers-Kronig data validation test was employed to validate the impedance data measurements and it was found...
-
Microstructure and Dielectric Properties of Barium-vanadate Glasses
PublikacjaThe ac and dc conductivity in barium-vanadate glasses was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) methods. The XRD results show that all samples are amorphous but microscopy investigation reveals that glasses with greater amount of V2O5...
-
Dielectric Spectroscopy Studies and Modelling of Piezoelectric Properties of Multiferroic Ceramics
PublikacjaCompounds and solid solutions of bismuth ferrite (BiFeO3)—barium titanate (BaTiO3) system are of great scientific and engineering interest as multiferroic and potential high-temperature lead-free piezoelectric materials. In the present paper, the results of research on the synthesis and characterisation of 0.67Bi1.02FeO3–0.33BaTiO3 (67BFBT) ceramics in terms of crystal structure and dielectric and piezoelectric properties are reported....
-
Modelling of dielectric properties of BiNbO4-based microwave ceramics
PublikacjaIn the present paper results of the studies devoted to computer simulations of dielectric response of electroceramics in a frequency domain as well as analysis of the experimental data are given. As an object of investigations BiNbO4-based microwave ceramics was taken. Simulations of the hypothetical impedance response of the ceramic system were performed under assumption of the brick-layer model. A strategy for analysis and modelling...
-
Effects of V2O5 Additive on Structure and Dielectric Properties of BiNbO4 Ceramics
PublikacjaGoal of the present research was to investigate the influence of V2O5 additive on the structure and dielectric properties of BiNbO4 ceramics. To fabricate BiNbO4 ceramics with V2O5 added the solid state reaction route and pressureless sintering was utilized. Thus obtained ceramics was characterized in terms of its microstructure (SEM), chemical composition (EDS), phase composition and crystalline structure (X-ray phase and structural...
-
Influence of Dielectric Overlay Dimensions on Performance of Miniaturized ESPAR Antenna
PublikacjaIn this paper, the influence of dielectric overlay size on miniaturized ESPAR antenna performance has been investigated. The dielectric overlay’s main function is antenna’s size reduction but it can also be used to modify its radiation pattern. This creates the possibility of easy adopting antenna parameters to different applications by swapping used overlay. In particular, the lowering of antenna’s main beam elevation direction...
-
Influence of Sn and Pb Ions Substitutions on Dielectric Properties of Barium Titanate
PublikacjaThe results of the microstructural and dielectric measurements of (Ba1-xPbx)(Ti1-xSnx)O3 (BPTSx) (x = 0, 0.05, 0.10, 0.30) polycrystalline samples are presented. The samples were obtained by means of a high temperature synthesis and their expected stoichiometry was confirmed by energy dispersive spectroscopy (EDS) measurements. The dielectric properties of BPTSx were studied with the use of broadband dielectric spectroscopy. The...
-
Characterization of Defects Inside the Cable Dielectric With Partial Discharge Modeling
PublikacjaThe continuous monitoring of power system devices is an important step toward keeping such capital assets safe. Partial discharge (PD)-based measurement tools provide a reliable and accurate condition assessment of power system insulations. It is very common that voids or cavities exist in every solid dielectric insulation medium. In this article, different voids are modeled and analyzed using an advanced finite element (FE)-based...
-
Dissociative ionization dynamics of dielectric gas C3F7CN
PublikacjaFluoronitrile C3F7CN is a promising candidate for the replacement of SF6 dielectric gas in high-voltage insulation. We present a combined experimental and theoretical study on its ionization dynamics probed in the 0-100 eV energy range. We exploited the total ion collection technique to determine the absolute ionization cross section, mass spectrometry to determine the fragment branching ratios and ab initio nonadiabatic molecular...
-
Surface Dielectric Barrier Discharge Plasma Actuators
PublikacjaThis paper presents a part of the works conducted in the Plasmaero European project (task 1.1) on surface dielectric barrier discharge actuators applied to airflow control. The study is divided into several parts. In the first part, the goal is to enhance the electric wind produced by a typical single DBD actuator by optimization of the active electrode shape. For instance, the use of a thin wire instead of a plate air-exposed...
-
Left-handed propagation characteristics of a dielectric and metal-loaded periodic circular waveguide
PublikacjaIn this paper, a periodic dielectric/metallic rod is located in a circular waveguide to obtain left-handed operation. Two geometries of the dielectric/metallic rod are proposed and examined. The dispersion characteristics of the investigated waveguides are obtained using a surface impedance model. Moreover, equivalent circuit models are proposed allowing for calculation of the dispersion characteristics and scattering parameters...
-
Influence of Phase Composition on Dielectric Properties of Bismuth-Based Ceramics with Scheelite-Type Structure
PublikacjaGoal of the present research was to study dielectric properties of BiNbO4 ceramics fabricated by solid state reaction route followed with pressureless sintering. The samples were fabricated from the mixture of oxides, viz. Nb2O5 and Bi2O3. Apart from stoichiometric amount an excess of 3%, 5% and 10% by mole of Bi2O3 was used. It was found that an excess amount of Bi2O3 oxide caused formation of Bi5Nb3O15 minor phase in amount of...
-
Multi-Objective Design Optimization of Compact Quasi-Isotropic Dielectric Resonator Antenna
PublikacjaMulti-objective optimization of a quasi-isotropic dielectric resonator antenna (DRA) is presented. Utilization of variable-fidelity electromagnetic (EM) DRA models, response surface approximations, and response correction techniques, allows us to obtain—at a low computational cost—a set of alternative antenna designs representing the best possible trade-offs between three conflicting objectives: antenna size, its reflection response,...
-
Piezoresponse force microscopy and dielectric spectroscopy study of Ba0.6Sr0.4TiO3 thin films
PublikacjaResearch on synthesis, characterization and determination of processing – structure – property relationships of commercially important ferroelectric thin films has been performed. The sol-gel-type solution deposition technique was applied to produce good quality thin films of Ba0.6Sr0.4TiO3 (BST60/40) chemical composition on the stainless steel substrates. The thin films were characterized in terms of their microstructure, crystal...
-
High frequency impulse ground penetrating radar application in assessment of interlayer connections
PublikacjaGround Penetrating Radar (GPR) technique is commonly used in the nondestructive evaluation of pavement structures. In particular, this method is used to estimate thicknesses of pavement layers as well as it can be utilized in advanced studies of pavement structures. The device presented in this paper comprise the high frequency impulse antennas that allow for investigating the interlayer zones in terms of their electromagnetic...
-
Mg2+ Doping Effects on the Structural and Dielectric Properties of CaCu3Ti4O12 Ceramics Obtained by Mechanochemical Synthesis
PublikacjaIn this study, ceramic CaCu3Ti4O12 (CCTO) and CaCu3−xMgxTi4O12 solid solutions in which 0.1 ≤ x ≤ 0.5 were prepared by the mechanochemical method, realized by a high‐energy ball milling technique. The effects of the Mg2+ ion concentration and sintering time on the dielectric response in the prepared ceramics were investigated and discussed. It was demonstrated that, by the use of a sufficiently high energy of mechanochemical treatment,...
-
Effective dielectric constant of two phase systems: Application to mixed conducting systems
PublikacjaW pracy przedstawiono wyniki badań spektroskopii impedancyjnej systemów dwufazowych oraz ich porównanie z wynikami oczekiwanymi przez różne modele.
-
Fabrication of exfoliated graphite reinforced silicone rubber composites - Mechanical, tribological and dielectric properties
PublikacjaThe effect of exfoliated graphite (EG) on the mechanical, tribological and dielectric properties of the silicone rubber (QM) composites has been systematically investigated and analysed. Morphological analysis of the composites helps to understand the interfacial interaction between the filler and the rubber matrix as well as wear mechanism respectively. An enhancement in the mechanical, tribological and dielectric properties was...
-
Fabrication of exfoliated graphite reinforced silicone rubber composites - Mechanical, tribological and dielectric properties
PublikacjaThe effect of exfoliated graphite (EG) on the mechanical, tribological and dielectric properties of the silicone rubber (QM) composites has been systematically investigated and analysed. Morphological analysis of the composites helps to understand the interfacial interaction between the filler and the rubber matrix as well as wear mechanism respectively. An enhancement in the mechanical, tribological and dielectric properties was...
-
Dielectric properties of barium-vanadate glasses
Dane BadawczeThe linear impedance of barium-vanadate glasses was measured. Samples of the composition of xBaO-(100-x)V2O5 where x= 30, 40 and 45 (in %mol) were prepared by the conventional melt quenching technique. Appropriate amounts of reagents: BaO (≥99.9%, P.P.H STANLAB Sp.J.) and V2O5 (≥99.9%, POCH) were thoroughly mixed in an agate mortar. The melting was...
-
Modal Analysis of Planar Elliptical Resonator Deposited on Unshielded Dielectric Slab
PublikacjaModal analysis of isolated open planar elliptical patch placed on dielectric slab is presented in the paper. It applies concept of Illuminating Modes which is formulated for the case of two-side opened structure. The current on patch is expanded in basis functions in form of Mathieu radial and angular functions. The spectrum of excited modes for exemplary planar resonators is presented and discussed using the concept of power of...
-
Dielectric properties of modified graphene oxide filled polyurethane nanocomposites and its correlation with rheology
PublikacjaThis study aims at investigating the dynamic mechanical, dielectric and rheological properties of reinforced polyurethane (PU) nanocomposites containing hydrophilic graphene oxide (GO) and/or hydrophobic modified graphene oxide (mGO) sheets. The organic modification of GO was performed with 4,4′-methylenebis (phenyl isocyanate) (MDI) and the samples were prepared by solvent mixing. We found that addition of mGO provides a more...
-
An Analysis of Elliptical-Rectangular Multipatch Structure on Dielectric-Coated Confocal and Nonconfocal Elliptic Cylinders
PublikacjaA rigorous analysis of the resonance frequency problem of an elliptical-rectangular microstrip structure mounted on dielectric-coated elliptic conducting cylinder, with electrically small radius, is investigated in this paper. A full-wave analysis and a moment-method calculation are employed. The analysis is carried out considering the expansion of the field as a series of Mathieu functions. The complex resonance frequencies of...
-
Design of Frequency-Reconfigurable Branch-Line Crossover Using Rectangular Dielectric Channels
PublikacjaThis paper presents an efficient yet straightforward passive reconfiguration technique to tune the operating frequency of a branch-line crossover (BLCO). The underlying principle is to fill rectangular dielectric channels (RDCs) prepared beforehand with either air or materials of different relative permittivity. Two configurations (one RDC and three RDCs in each arm) of the branch-line crossover are employed to estimate the tunability...
-
Trailing-Edge Separation Control of a NACA 0015 Airfoil Using Dielectric-Barrier-Discharge Plasma Actuators
PublikacjaThis paper presents a part of the works conducted in the Plasmaero European project (task 3.1), where the trailing-edge flow separation of a NACA 0015 airfoil has been controlled using four different dielectric barrier discharge (DBD) actuator types at three institutions across Europe. The results show that it is possible to enhance the aerodynamic performance of aircraft at speeds up to 40 m/s. Dielectric-barrier-discharge vortex...
-
Ionic liquids for nano- and microstructures preparation. Part 2: Application in synthesis
PublikacjaIonic liquids (ILs) are widely applied to prepare metal nanoparticles and 3D semiconductor microparticles. Generally, they serve as a structuring agent or reaction medium (solvent), however it was also demonstrated that ILs can also play a role of a co-solvent, metal precursor, reducing as well as surface modifying agent. The crucial role and possible types of interactions between ILs and growing particles have been presented in...
-
Spectroscopic Study of Plasma Polymerized a-C:H Films Deposited by a Dielectric Barrier Discharge
PublikacjaPlasma polymerized a-C:H thin films have been deposited on Si (100) and aluminum coated glass substrates by a dielectric barrier discharge (DBD) operated at medium pressure using C2Hm/Ar (m = 2, 4, 6) gas mixtures. The deposited films were characterized by Fourier transform infrared reflection absorption spectroscopy (FT-IRRAS), Raman spectroscopy, and ellipsometry. FT-IRRAS revealed the presence of sp3 and sp2 C–H stretching and...
-
Comparison of How Graphite and Shungite Affect Thermal, Mechanical, and Dielectric Properties of Dielectric Elastomer-Based Composites
Publikacja -
Dielectric strenght of the ultra - short fuse
PublikacjaW referacie omówiono współpracę ultraszybkiego bezpiecznika z bezstykowymhybrydowym ogranicznikiem prądów. Przeanalizowano wytrzymałość kanału połukowego bezpiecznika w zależności od długości topika oraz czasu działania tranzystora IGBT. Omówiono warunki i wyniki badań eksperymentalnych.
-
Dielectric Barrier Discharge Systems with HV Generators and Discharge Chambers for Surface Treatment and Decontamination of Organic Products
PublikacjaThe article presents applications of systems with power electronic converters, high voltage transformers, and discharge chambers used for nonthermal, dielectric barrier discharge plasma treatment of a plastic surface and decontamination of organic loose products. In these installations, the inductance of the high voltage transformers and the capacitances of the electrode sets form resonant circuits that are excited by inverters....
-
Finite element/mode-matching analysis of ferrite/dielectric line junctions of arbitrary cross-section
PublikacjaThis paper is focused on the analysis of line junctions obtained as a cascade of dielectric and ferrite guides of arbitrary cross-section. The main application of such structures is nonreciprocal devices such as isolators, circulators, or phase shifters. The efficient finite element/mode-matching approach is proposed to the analysis of such structures. In this approach, thefiniteelementmethod is applied todetermine propagation...
-
Kinedynamics of Spherical Wavefields in Fluid and Dielectric Continua
PublikacjaDistubances induced by physical sources in fluids or dielectrics maintain their primary character while propagating throughout either of these bi-dynamic continua. The paper defines and illustrates four sets of bi-fields based on four specific fundamental kinedynamic solutions to inhomogeneous wave equations related to quasi-point acoustic and electromagnetic sources.
-
On dielectric spectra of thin copper phthalocyanine films
PublikacjaPraca przedstawia niskosygnałowe widma dielektryczne, w zakresie częstotliwości 25 Hz-1 MHz, układów kanapkowych takich jak złoto/ftalocyjanina miedzi/magnez i złoto/ftalocyjanina miedzi/złoto.Przeprowadzona analiza umożliwiła odróżnienie w odpowiedzi dielektrycznej oporności elektrod i polaryzacji sieci od procesów związanych z transportem elektrycznych, takich jak relaksacja nośników ładunku w obszarze ładunku przestrzennego...
-
Oblique scattering by an array of conducting and dielectric cylinders
PublikacjaMetodę dopasowania rodzajów zastosowano do połączenia zastępczego pola rozproszonego od dowolnej konfiguracji prętów metalowych i dielektrycznych z falą płaską padającą pod dowolnym kątem na określoną strukturę. Zaprezentowano charakterystyki rozpraszania w strefie dalekiej dla konfiguracji czterech, pięciu i siedmiu prętów metalowych i dielektrycznych umieszczonych w cylindrycznym obszarze wypełnionym dielektrykiem przy skośnym...
-
Nonlinear free and forced vibrations of a dielectric elastomer-based microcantilever for atomic force microscopy
PublikacjaThe majority of atomic force microcode (AFM) probes work based on piezoelectric actuation. However, some undesirable phenomena such as creep and hysteresis may appear in the piezoelectric actuators that limit their applications. This paper proposes a novel AFM probe based on dielectric elastomer actuators (DEAs). The DE is modeled via the use of a hyperelastic Cosserat model. Size effects and geometric nonlinearity are included...
-
Expedited Simulation-Driven Multi-Objective Design Optimization of Quasi-Isotropic Dielectric Resonator Antenna
PublikacjaMajority of practical engineering design problems require simultaneous handling of several criteria. Although many of design tasks can be turned into single-objective problems using sufficient formulations, in some situations, acquiring comprehensive knowledge about possible trade-offs between conflicting objectives may be necessary. This calls for multi-objective optimization that aims at identifying a set of alternative, Pareto-optimal...
-
The influence of polypropylene-block/graft-polycaprolactone copolymers on melt rheology, morphology, and dielectric properties of polypropylene/polycarbonate blends
PublikacjaThe paper discusses the relationship between rheology and morphology of immiscible polypropylene (matrix))/polycarbonate (dispersed phase) blends compatibilized with novel polypropylene-polycaprolactone block and graft copolymers. Transmission electron microscopy (TEM) experiments revealed uniform droplet morphologies and a reduction of the average size of the dispersed phase upon addition of the compatibilizer. The results suggested...
-
Dielectric and Optical Studies of FLC Sample with Helix Inversion
Publikacja -
Nanostructure and dielectric behavior of vanadate glasses containing BaTiO3
PublikacjaThe ac and dc electrical conductivity of barium titanate doped bismuth-vanadate as-quenched and heat-treated materials was measured in the frequency range from 1 mHz to 1 MHz and in the temperature range from 153 K to 423 K with the impedance spectroscopy method. The microstructure was investigated by means of XRD, scanning electron microscopy (SEM), atomic force microscopy (AFM) and confocal microscopy. The obtained results showed...
-
Properties of humidity sensors with porous Al2O3 as a dielectric layer
PublikacjaPrzedstawiono wpływ wartości wilgotności względnej na charakterystki ceramicznego czujnika z porowatą warstwą Al2O3. Pokazano wpływ wybranych parametrów technologicznych na właściwości czujnika. Wyniki pomiarów dla dwóch grup czujników poddano analizie wykorzystując znane z literatury układy zastępcze.
-
Electronically Excited States in Solution via a Smooth Dielectric Model Combined with Equation-of-Motion Coupled Cluster Theory
PublikacjaWe present a method for computing excitation energies for molecules in solvent, based on the combination of a minimal parameter implicit solvent model and the equation-of-motion coupled-cluster singles and doubles method (EOM-CCSD). In this method, the solvent medium is represented by a smoothly varying dielectric function, constructed directly from the quantum mechanical electronic density using only two tunable parameters. The...
-
Role of cholesterol in substrate recognition by -secretase
Publikacja-Secretase is an enzyme known to cleave multiple substrates within their transmembrane domains, with the amyloid precursor protein of Alzheimer’s Disease among the most prominent examples. The activity of -secretase strictly depends on the membrane cholesterol content, yet the mechanistic role of cholesterol in the substrate binding and cleavage remains unclear. In this work, we used all-atom molecular dynamics simulations to examine...
-
Electromagnetic properties of a dielectric slab with an embedded silver nanowire grating
Publikacja -
Scattering of the plane wave from a periodically perforated dielectric slab
Publikacja -
Electromagnetic characterization of a silver nanowire grating embedded into a dielectric slab
Publikacja -
Theory of scattering by an array of lossy dielectric, ferrite and conducting cylinders.
PublikacjaOpisano metodę analizy umożliwiającą określenie zastępczego pola rozproszonego od dowolnej konfiguracji prętów dielektrycznych, ferrytowych lub metalowych na zewnętrznym obszarze cylindrycznym w celu połączenia go z wybranym pobudzeniem i znalezienia macierzy rozproszenia układu. Prezentowane podejście znajduje zastosowanie w analizie struktur zamkniętych i określanie macierzy rozpraszania złączy falowodowych jak i otwartych...
-
Scattering by an array of conducting, lossy dielectric, ferrite and pseudochiral cylinders.
PublikacjaOpisano metodę analizy rozpraszania fali elektromagnetycznej w systemach zawierających cylindryczne pręty dielektryczne, metalowe, ferytowe i pseudochiralne i wykorzystanie w/w metody w problemach zamkniętych i znajdowanie macierzy rozpraszania wieloportowych złączy falowodowych oraz w problemach otwartych i badanie charakterystyk rozpraszania zarówno w strefie dalekiej jaki bliskiej.
-
Oblique Plane Wave Scattering by an Array of Dielectric and Metamaterial Cylinders.
PublikacjaBadanie wpływu ujemnej przenikalności elektrycznej i magnetycznej na parametry rozproszenia fali elektromagnetycznej dla cylindrów wykonanych z dielektryka i metamateriału. Wykorzystanie zmodyfikowanej procedury iteracyjnej i metody dopasowania rodzajów do analizy ukośnego padania fali elektromagnetycznej na zbiór równoległych cylindrów.
-
Rigorous Modal Analysis of Structures Containing Inhomogeneous Dielectric Cylinders.
PublikacjaW pracy wykorzystano zmodyfikowaną procedurę iteracyjną i metodę dopasowania rodzajów w celu analizy struktur zawierających asymetrycznie umieszczone, niepełnej wysokości lub wielowarstwowe, niejednorodne, cylindryczne rezonatory dielektryczne. Analiza bazuje na nowatorskiej koncepcji zwanej hybrydową macierzą impedancyjną (HIM - hybryd impedancje matrix), która opisuje relacje pomiędzy całkowitym polem elektrycznym i magnetycznym...
-
Fast numerical analysis of dielectric resonators with perturbed rotational symmetry
PublikacjaW artykule zaprezentowano metody szybkiej analizy rezonatorow o symetrii zblizonej do osiowej metodą różnic skończonych w dziedzinie częstotliwości. Dzięki użyciu techniki rozwinęć funkcyjnych w jednorodnych obszarach uzyskano redukcję rozmiaru i znaczne przyspieszenie zbieżności problemu własnego, reprezentującegowspomniane układy. Dzięki elastycznemu sposobowi łączenia dziedzin z i bez rozwinięć funkcyjnych możliwe było zaadaptowanie...
-
Broadband dielectric spectroscopy studies of multiple times processed poly(lactic acid)-carbon black composites
Dane BadawczeThis dataset contains broadband dielectric spectroscopy studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different...
-
Application of thin dielectric films in low coherence fiber-optic Fabry-Pérot sensing interferometers: comparative study
Publikacja -
Plasmon resonances of an infinite grating of silver wires coated with dielectric envelopes
Publikacja