Filtry
wszystkich: 257
wybranych: 178
Wyniki wyszukiwania dla: CTOD
-
Designate of CTOD for WM and HAZ, report no: WOiO/II/122/2014
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Designate CTOD of Weld Metal of butt weld, No WOiO/II/108/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
THE EFFECT OF NOTCH DEPTH ON CTOD VALUES IN FRACTURE TESTS OF STRUCTURAL STEEL ELEMENTS
PublikacjaIn elements of steel structures working at low temperatures, there is a risk of appearance of brittle fracture. This risk is reduced through the use of certified materials having guaranteed strength at a given temperature. A method which is most frequently used to determine brittle fracture toughness is the Charpy impact test, preformed for a given temperature. For offshore structures intended to work in the arctic climat e, the...
-
Designate CTOD Heat Affected Zone of butt weld, Report No: WOiO/II/76/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATION ON SPECIMEN GEOMETRY EFFECT ON THE CTOD VALUE FOR VL-E36 SHIPBUILDING STEEL
PublikacjaThere are special cases in the marine industry, where additional material tests, such as the fracture toughness test, must be performed. Additional fracture toughness tests, such as CTOD (Crack Tip Opening Displacement), are typically performed on three-point bend specimens. The dimension that defines all the specimen dimensions is the thickness of the material to be tested. It is recommended by classification societies (e.g. DNVGL)...
-
Occurrence of anisakid nematodes in Atlantic cod (Gadus morhua) and Greenland cod (Gadus ogac), West Greenland
Publikacja -
CTOD designation for WM and HAZ in butt joint made from S460 ML steel, Expertise No. WOiO/II/82/2015
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
The propagation of the waves in the CTO S.A. towing tank
PublikacjaThe paper presents the results of research focused on the wave propagation in the CTO S.A. deepwater towing tank. In the scope of paper, the wavemaker transfer function was determined for regular waves, based on the Biésel Transfer Function and further for irregular waves, based on Hasselman model of nonlinear energy transfer. The phenomena: wave damping, wave breakdown and wave reflection, were measured, analyzed and mathematically...
-
Wpływ parametrów geometrycznych próbki stalowej na uzyskaną wartość wskaźnika krytycznego rozwarcia wierzchołka szczeliny CTOD w badaniach odporności na pękanie
PublikacjaW pracy podjęto problem określania ciągliwości materiału metodami mechaniki pękania, jako jednego z częściej wymaganych kryteriów dla konstrukcji okrętowych i oceanotechnicznych. Na podstawie rozważań i modeli numerycznych, studiowano problem wpływu parametrów geometrycznych próbki na wynik znormalizowanej próby określania krytycznego rozwarcia wierzchołka szczeliny - CTOD. W pierwszej części pracy dokonano przeglądu metod...
-
Detecting the medieval cod trade: a new method and first results
Publikacja -
The estimation of norwegian cod size distribution from acoustic data
Publikacja -
Optimization of condition for demineralization Baltic cod (Gadus morhua) backbone
PublikacjaKręgosłupy dorsza bałtyckiego (Gadus morhua) są alternatywnym źródłem kolagenu. Aby uzyskać z nich natywny niezanieczyszczony kolagen należy usunąć z nich białka mięśniowe i sole mineralne. Obecność tych związków pogarsza funkcjonalne właściwości preparatu kolagenowego. Dlatego celem pracy było opracowanie optymalnych parametrów demineralizacji kręgosłupów dorsza. Najlepszy efekt demineralizacji, nieomal 100%, przy stratach tylko...
-
Isolation of collagen from the skins of Baltic cod (Gadus morhua).
PublikacjaBezbarwny kolagen wydzielono ze skór dorsza z ok. 90% wydajnością stosując trzykrotną, 24 godzinną ekstrakcję materiału 0.5 M roztworem kwasu cytrynowego, przy stosunku surowiec : rozpuszczalnik = 1 : 4. Stosując 0.5% dodatek niejonowych detergentów do roztworów ekstrahujących białka niekolagenowe ze skór uzyskuje się bezwonne izolaty kolagenu.
-
Importance of model tests in design and operation of watercraft for example CTO
PublikacjaShip Hydromechanics Division is a specialized research and development department of Ship Design and Research Centre conducting tests and research in the field of hydromechanics, connected with design and operation of ships and other floating structures, in scope of: predictions, numerical analyses, designs of - hull shape optimized with respect to the ship’s functions with the application of modern design tools, screw propellers...
-
Organic matter removal efficiency in treatment wetlands simulation by COD fractions
PublikacjaThe objective of this paper was to investigate the organic fraction (colloidal, particulate, and dissolved) in sewage treatment in treatment wetland. Performance of TWs was simulated well with a simple first order model k – C* based on monitoring data. In this investigation background or residual concentration (C*) was assumed to be equal concentration of input influent organic matter in particulate (CODp). Calculated reaction...
-
Molecular and structural characteristics of cod gelatin films modifiedwith EDC and TGase
PublikacjaCod gelatin films before and after cross-linking of gelatin with 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDC) or transglutaminase (TGase) have been characterized by FT-IR spectroscopy and DSC analysis. For comparison, a film prepared from unmodified pig gelatin has been also analysed. The difference spectra showed that cod gelatin during the film formation involved first of all water-to-amide hydrogen bonds, and the film...
-
Influence of COD-fractions on removal effectiveness and accumulation of organic matter in constructed wetlands
PublikacjaW pracy wykazano, że efektywność usuwania substancji organicznej doprowadzanej w ściekach bytowo-gospodarczych do złóż hydrofitowych zależy od rodzaju frakcji substancji organicznej oraz ich stężeń. Na podstawie analizy poszczególnych frakcji ChZT (rozpuszczonych związków organicznych biologicznie łatwo- i nierozkładalnych oraz zawiesin organicznych biologicznie wolno- i nierozkładalnych) wykazano, że na akumulację substancji organicznej...
-
Modification of the properties of gelatin from skins of Baltic cod (Gadus morhua) with transglutaminase.
PublikacjaCelem pracy było ustalenie optymalnych warunków otrzymywania żelatyny ze skór dorsza bałtyckiego oraz modyfikacja enzymatyczna właściwości tego białka. Rybna żelatyna usieciowana przy użyciu transglutaminazy tworzy żele, które nie topią się nawet podczas ogrzewania w temperaturze 100C.
-
Isolation and some properties of collagen from the backbone of Baltic cod(Gadus morhua)
PublikacjaOssein from Baltic cod backbone was obtained after extraction of non-collagenous protein with 0.1 M NaOH solution and demineralization with 1.0 M HCl solution. The extractions were performed at 4 C for24, 48 and 72 h using a solid/solution ratio from 1:4 to 1:8 (w/v). After 48 h of extraction in 0.5 M acetic acid only about 25% of collagen was dissolved. After 48 h of extraction at optimal concentration of pepsin(4 mg/g ossein)...
-
The effect of high pressure and subzero temperature on gelation of washed cod and salmon meat
PublikacjaThe objective of the present work is to examine the infl uence of pressure up to 193 MPa at subzero temperature (without freezing of water) on myofi brillar proteins of salmon and cod meat and on the properties of gels obtained from washed mince of these fi sh. The solubility of proteins from myofi brils of cod and salmon meat suspended in 100 mM KCl solution increased aft er treating the samples with pressure above 60 MPa. The...
-
The effect of high pressure on formation of volatile amines in minced meat of cod (Gadus morhua)
PublikacjaThe effects of high pressure at subzero temperature (193 MPa, at −20 °C) on inactivation of natural microflora of cod meat and degradation of trimethylamine oxide (TMAO) to trimethylamine (TMA) during refrigerated storage and to dimethylamine (DMA) and formaldehyde (FA) during frozen storage were investigated. The content of TMA, DMA and FA in cod meat did not change immediately after pressure treatment. During 40 days of frozen...
-
Determination of COD Fractionation as a Key Factor for Appropriate Modelling and Monitoring of Activated Sludge Processes
PublikacjaAn operation of wastewater treatment plant is usually controlled by global parameters such as flow, solids retention time, sludge age, concentration of ammonia and dissolved oxygen, etc. It is considered that, together with the chemical and biological oxygen demand (COD and BOD), those parameters indirectly exhibit the effectiveness of activated sludge processes. Especially the BOD indicate the amount of organic pollution that...
-
Development of potential candidate reference materials for drugs in bottom sediment, cod and herring tissues
PublikacjaRegular use of a reference material and participation in a proficiency testing program can improve the reliability of analytical data. This paper presents the preparation of candidate reference materials for the drugs metoprolol, propranolol, carbamazepine, naproxen, and acenocoumarol in freshwater bottom sediment and cod and herring tissues. These reference materials are not available commercially. Drugs (between 7 ng/g and 32...
-
The influence of different acids and pepsin on the extractability of collagen from the skin of Baltic cod (Gadus morhua)
PublikacjaZastosowano 5,0 M roztwory kwasu cytrynowego, mlekowego, octowego oraz 0,115 M roztwór kwasu solnego. Kolagen z całych skór ekstrahowano w 4 st.C odpowiednimi kwasami (1 : 6, w/v) w czasie 24, 48 i 72 h. Stwierdzono, że kwas solny jest najmniej efektywnym rozpuszczalnikiem kolagenu spośród użytych kwasów. W zastosowanych warunkach doświadczeń maksymalnie można wyekstrahować kwasem cytrynowym 60 % kolagenu, kwasem octowym i mlekowym...
-
Interpreting the expansion of sea fishing in medieval Europe using stable isotope analysis of archaeological cod bones
Publikacja -
Determination of Chemical Oxygen Demand (COD) at Boron-doped Diamond (BDD) Sensor by Means of Amperometric Technique
Publikacja -
The influence of moderate pressure and subzero temperature on the shelf life of minced cod, salmon, pork and beef meat
PublikacjaThe effect of moderate pressure at subzero temperature on natural microflora of minced cod, salmony, pork and beef meat was studied. Pressure of 193 MPa at –20 °C caused reduction of total bacterial count in pork and beef meat by 1.1 and 0.6 log cycles, respectively, and by about 1.5 log cycles in fish meat. Under these conditions the psychrophilic and psychrotophic bacteria were below the detection limit (<10CFU/g of sample) in...
-
Determination of Chemical Oxygen Demand (COD) at Boron-doped Diamond (BDD) Sensor by Means of Amperometric Technique
PublikacjaA boron-doped diamond (BDD) sensor was proposed for effective detection of chemical oxygen demand (COD) by means of amperometric technique. Thin boron doped diamond active sensor layer was deposited on Si wafer and glassy carbon substrate by Microwave Plasma Enhanced Chemical Vapor Deposition (MW PE CVD). The structure of BDD was confirmed by Raman spectra analysis. Broad Raman bands centered at 482 cm-1 and 1219 cm-1 are typical...
-
Determination of chemical oxygen demand (cod) at boron-doped diamond (bdd) sensor by means of amperometric technique
PublikacjaA boron-doped diamond (BDD) sensor was proposed for effective detection of chemical oxygen demand (COD) by means of amperometric technique. Thin boron doped diamond active sensor layer was deposited on Si wafer and glassy carbon substrate by Microwave Plasma Enhanced Chemical Vapor Deposition (MW PE CVD). The structure of BDD was confirmed by Raman spectra analysis. Broad Raman bands centered at 482 cm-1 and 1219 cm-1 are typical...
-
Application of hydroacoustic system of distance measurement for estimating the cod codends shape at the model research station in Insko
PublikacjaPraca przedstawia wyniki pomiarów kształtu worków dorszowych w stacji badań modelowych Politechniki Szczecińskiej w Ińsku. Badane worki dorszowe są workamispecjalnie zaprojektowanymi do połowów selektywnych. W celu precyzyjnego pomiaru parametrów geometrycznych worków został opracowany nowy hydroakustyczny system do precyzyjnych pomiarów odległości. Zapewnia on równoczesny pomiar maksymalnie 100 różnych wymiarów w zakresie od 0.1m...
-
Stable Isotope Evidence for Late Medieval (14th–15th C) Origins of the Eastern Baltic Cod (Gadus morhua) Fishery
Publikacja -
The effect of chemical modifications on rheologicalproperties of collagen from of Baltic cod (Gadus morhua)skin stabilized by interaction with κ-carrageenan.
PublikacjaZbadano wpływ stężenia aldehydu glutarowego i EDC N-[3-(dimetyloamino)propylo]-N'-etylokarbodiimid na reologiczne właściwości kompleksu k-karagenu z kolagenem wydzielonym ze skór dorsza bałtyckiego (Gadus morhua) 0,5 M roztworem kwasu octowego i wytworzonych z nich błon. Stwierdzono, że dodanie do dyspersji aldehydu glutarowego, którego stężenie zmieniano od 0,05 do 0,2% powodowało natychmiastowy wzrost jej lepkości. Dodatek aldehydu...
-
The Influence of COD Fraction Forms and Molecules Size on Hydrolysis Process Developed by Comparative OUR Studies in Activated Sludge Modelling
PublikacjaThe activated sludge models (ASMs) commonly used by the International Water Association (IWA) task group are based on chemical oxygen demand (COD) fractionations. However, the proper evaluation of COD fractions, which is crucial for modelling and especially oxygen uptake rate (OUR) predictions, is still under debate. The biodegradation of particulate COD is initiated by the hydrolysis process, which is an integral part of an ASM....
-
The evaluation of COD fractionation and modeling as a key factor for appropriate optimization and monitoring of modern cost-effective activated sludge systems
PublikacjaA study was conducted to characterize the raw wastewater entering a modern cost effective municipal WWTP in Poland using two approaches; 1) a combination of modeling and carbonaceous oxygen demand (COD) fractionation using respirometric test coupled with model estimation (RTME) and 2) flocculation/filtration COD fractionation method combined with BOD measurements (FF-BOD). It was observed that the particulate fractions of COD obtained...
-
The effect of high pressure at subzero temperature on proteins solubility, drip loss and texture of fish (cod and salmon) and mammal’s (pork and beef) meat
PublikacjaOne of the possibilities of using high pressure technique in inactivation of microorganism is conducting this process at subzero temperature. However, for its practical application in meat preservation the appropriate properties of meat should be kept. Therefore, the aim of this work was to examine the effect of pressure at subzero temperature (without freezing of water) on proteins and texture of mammal’s and cold-adapted fish...
-
Optimisation of conditions for precipitation of collagen from solution using kappa-carrageenan. Studies on collagen from the skin of Baltic cod (Gadus morhua)
PublikacjaZbadano wpływ stężenia kolagenu (0,012-3%) wyekstrahowanego ze skór dorsza bałtyckiego (Gadus morhua) i stężenia kappa-karagenu w obecności NaCl (0-5%) na wydajność strącania włókien kolagenowych z roztworu przy pH 2,2-8. Stwierdzono, że wydajność strącania włókien jest wprost proporcjonalna do masowego stosunku kappa-karagen : kolagen w zakresie niższym od 0,4. Kolagen rozpuszczony w kwasie cytrynowym jest całkowicie strącony,...
-
Funkcjonalne właściwości preparatu białek mięśniowych z kręgosłupów dorsza bałtyckiego = Functional properties of a muscle protein preparation from Baltic cod spine
Publikacja -
Isolation and characterization of Acid Soluble Collagen from the Skin of African Catfish (Clarias gariepinus), Salmon (Salmo salar) and Baltic cod (Gadus morhua)
PublikacjaAcid-soluble collagen (ASC) from the fish skin of African catfish (Clarias gariepinus), Salmon (Salmo salar) and Baltic cod (Gadus morhua) was extracted and characterized. The ASC extraction yield was 75%, 73% and 68%, respectively. The denaturation and melting temperatures of African catfish ASC (29.3°C and 100.0°C) were significantly higher than ASC of Salmon and Baltic cod (20.6°C and 90.5°C; 15.2°C and 86.7°C, respectively), assessed...
-
FE<sub>2</sub>(SO<sub>4</sub>)<sub>3</sub> and Bentonite Use to Reduce COD Indicators in Wastewater Containing Detergents
Publikacja -
Comparative analysis of the quality parameters and the fatty acid composition of two economically important Baltic fish: cod, Gadus morhua and flounder, Platichthys flesus (Actinopterygii) subjected to iced storage
Publikacja -
Wpływ dodatku odcieków składowiskowych do oczyszczanych ścieków komunalnych na wielkość frakcji ChZT
PublikacjaManaging landfill leachate is one of the most important problems with maintaining landfills. The aim of this study was to determine the influence on COD fraction of landfill leachate addition from 0,5% to 5% to raw wastewater. The results of this study show that soluble inert COD in wastewater and mixture wastewater with landfill leachate constituted the smallest percentage of total COD. Nonetheless this fraction (soluble inert...
-
NUMERICAL MODEL OF PLASTIC DESTRUCTION OF THICK STEEL STRUCTURAL ELEMENTS
PublikacjaIn the shipbuilding industry, the risk of brittle fracture of the structure is limited by using certified materials with specified impact strength, determined by the Charpy method (for a given design temperature) and by supervising the welding processes (technology qualification, production supervision, non-destructive testing). For off-shore constructions, classical shipbuilding requirements may not be sufficient. Therefore, the...
-
The role of particulate and colloidal substrate in biological nutrient removal activated sludge systems
PublikacjaThe authors investigated COD fractionation according to the physical state (soluble/colloidal/particulate) in four wastewater treatment plants (WWTPs) in northern Poland. It was found that particulate and colloidal organic compounds constituted up to 70% of total COD. On the other hand, according to literature data, municipal wastewater contains readily and slowly biodegradable substrates in the amount of approximately 10-30% and...
-
Automotive fleet repair facility wastewater treatment using air/ZVI and air/ZVI/H2 O2 processes
PublikacjaAdvanced automotive fl eet repair facility wastewater treatment was investigated with Zero-Valent Iron/Hydrogen Peroxide (Air/ZVI/H2 O2 ) process for different process parameters: ZVI and H2 O2 doses, time, pH. The highest Chemical Oxygen Demand (COD) removal effi ciency, 76%, was achieved for ZVI/H2 O2 doses 4000/1900 mg/L, 120 min process time, pH 3.0. COD decreased from 933 to 227 mg/L. In optimal process conditions odor and...
-
Sequential treatment of landfill leachate by electrocoagulation/aeration, PMS/ZVI/UV and electro-Fenton: Performance, biodegradability and toxicity studies
PublikacjaThis study presents a systematic study on sequential treatment of highly resistant landfill leachate by electrocoagulation (EC)/aeration, sulfate radical advanced oxidation process (SR-AOP) and electro-Fenton (EF). In case of SR-AOP, peroxymonosulfate (PMS) catalyzed by zero valent iron (ZVI) and ultraviolet irradiation (UV) system was developed. Treatment process was optimized in respect to COD removal. Analysis of results revealed...
-
The role of the combined nitrogen-sulfur-carbon cycles for efficient performance of anammox-based systems
PublikacjaThe combined anammox/mixotrophic denitrification process was conducted in two granular sequencing batch reactors (SBRs) during a 200-day operation. Both reactors were fed with synthetic medium, but SBR2 was enriched with additional sulfate (SO4 2 ) which influenced sulfate reduction ammonium oxidation (SRAO) and heterotrophic reduction of SO4 2 by sulfate reducing bacteria. It was hypothesized that the addition of SO4 2 could...
-
Influence of Material Thickness on the Ductile Fracture of Steel Plates for Shipbuilding
PublikacjaIn the shipbuilding industry, the risk of brittle fractures is relatively high because some units operate in arctic or subarcticzones and use high thickness (up to 100 mm) steel plates in their structures. This risk is limited by employing certifiedmaterials with a specific impact strength, determined using the Charpy method (for a given design temperature) and byexercising control over the welding processes (technology qualification,...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements
PublikacjaThe dataset titled EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6 contains CMOD (Crack Mouth Opening Displacement) - Force record which is the base for evaluation of fracture toughness of structural steel. Bend specimens witch Bx2B section (B= 50mm), and relative initial crack length a0 / W = 0.60 were used. The test was carried out at ambient temperature in accordance to ISO 12135 standard....
-
WAYS TO IMPROVE THE EFFICIENCY OF WASTEWATER TREATMENT OF A CARDBOARD AND PAPER MILL
PublikacjaThe results of research on physical and chemical methods for the preliminary treatment of wastewater of a cardboard and paper factory in Khmelnytskyi region of Ukraine are presented. At the cardboard and paper factory, wastewater is treated at a sewage treatment plant, which includes sand traps, primary radial sedimentation tanks, aeration tanks with activated sludge regenerators, secondary radial sedimentation tanks, and bioponds....
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements Dataset
PublikacjaThe dataset titled EH36 steel for shipbuilding (plate thickness 50 mm) – CMOD – force record, a0/W=0.6 contains a CMOD (Crack Mouth Opening Displacement) – Force record which is the base for evaluation of the fracture toughness of structural steel. Bend specimens with a Bx2B section (B = 50 mm), and relative initial crack length a0/W=0.60 were used. The test was carried out at ambient temperature in accordance with the ISO 12135...