Filtry
wszystkich: 824
wybranych: 677
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: donating
-
Microscale diamond protection for a ZnO coated fiber optic sensor
PublikacjaFiber optic sensors are widely used in environmental, biological and chemical sensing. Due to the demanding environmental conditions in which they can be used, there is a risk of damaging the sensor measurement head placed in the measuring field. Sensors using nanolayers deposited upon the fiber structure are particularly vulnerable to damage. A thin film placed on the surface of the fiber end-face can be prone to mechanical damage...
-
Influence of Two-Stage Anodization on Properties of the Oxide Coatings on the Ti–13Nb–13Zr Alloy
PublikacjaThe increasing demand for titanium and its alloys used for implants results in need of such innovative surface treatment that may jointly increase corrosion resistance and biocompatibility, and demonstrate antibacterial protection at no cytotoxicity. The purpose of this research was to characterize the effect of two-stage anodization, performed for 30 min in phosphoric acid, at the presence of hydrofluoric acid in the second stage....
-
Control of the wind turbine generator
PublikacjaWind power system consists of two main parts: wind turbine and electrical generator. Wind turbine converts the energy of the flowing air into mechanical energy, next generator converts this energy into electrical energy that is sent to the power system. These two processes should be realized with maximum efficiency and the following requirements for the control system can be formulated: opti-mal wind power conversion, compensation...
-
Krajobraz nomadyczny w Muittalus samid birra (1910) Johana Turiego
PublikacjaThe article introduces Muittalus samid birra (1910, An account of the Sami) by Johan Turi, the fi rstbook with a secular content written in the sami language by a sami person. The author, a wolf hunterand reindeer-breeder, describes a broad spectrum of his people’s daily life. Pictures of everydayactivities are supplemented with stories about the sami people’s knowledge of the world (traditions,myths,...
-
Reduction of noise and rolling resistance by horizontal grinding of asphalt pavements
PublikacjaGrinding of cement concrete pavements to reduce unevenness and noise is common since a long time. Grinding is then made with wheels equipped with diamond blades rotating in the vertical plane. This creates narrow vertical/longitudinal grooves in the pavement. It is not applied to asphalt pavements. In this paper an alternative type of grinding is studied. In this case plates with diamond heads rotate in the same plane as the pavement,...
-
AN ALTERNATIVE WAY OF DETERMINING MECHANICAL PROPERTIES OF WOOD BY MEASURING CUTTING FORCES
PublikacjaThe cutting force is an energetic effect of splitting material, and might be therefore considered from a point of view of modern fracture mechanics. The dedicated mathematical model developed for description of the wood cutting has been developed here on the base of fracture theory, and includes work of separation (fracture toughness) in addition to the material plasticity and friction. The effect of the cutting edge dullness is...
-
Impact Behaviour of Glass Fribre /Epoxy Composites with Nano-Enhanced Resin after Water Exposure
PublikacjaImpact behaviour of glass fibre /epoxy composites with nano- SiO2 modified resin was studied in terms of low velocity impact after water exposure. Nanocomposites with 1%, 2%, 3% 5% 7% nano-SiO2 (Nanopox- Evonic) were investigated. Peak impact load and impact damage area as a function of nanoparticle contents were compared for dry specimens and for samples exposed to water (0.7 %wt. 1.7% water absorbed) at 1J, 2J 3J impact energies....
-
Styrene-Butadiene Rubber/Modified Ground Tire Rubber Blends Co-Vulcanization: Effect of Accelerator Type
PublikacjaGround tire rubber was thermo-mechanically modified with using a co-rotating twin screw extruder. Modification of GTR was conducted in autothermal conditions. Styrene-butadiene rubber and modified ground tire rubber blends were prepared via two-roll milling. Obtained compounds were cured with conventional system (sulfur/vulcanization accelerator ratio was 2:1). During this research three commonly vulcanization accelerators (MBT,...
-
Polychlorinated biphenyls (PCBs) in bottom sediments: Identification of sources
PublikacjaPolychlorinated biphenyls (PCBs) can enter the environment from various sources. They are synthetic chemicals and as such are present in the environment mainly as mixtures containing various amounts of PCB congeners. It is therefore difficult to pinpoint the source of PCB emissions into the environment and the pathways along which they migrate there. The situation is different where locating the emission sources of polycyclic aromatic...
-
On the size of identifying codes in triangle-free graphs
PublikacjaIn an undirected graph G, a subset C⊆V(G) such that C is a dominating set of G, and each vertex in V(G) is dominated by a distinct subset of vertices from C, is called an identifying code of G. The concept of identifying codes was introduced by Karpovsky, Chakrabarty and Levitin in 1998. For a given identifiable graph G, let gammaID(G) be the minimum cardinality of an identifying code in G. In this paper, we show that for any connected...
-
Methods of measurement signal acquisition from the rotational flow meter for frequency analysis
PublikacjaOne of the simplest and commonly used instruments for measuring the flow of homogeneous substances is the rotational flow meter. The main part of such a device is a rotor (vane or screw) rotating at a speed which is the function of the fluid or gas flow rate. A pulse signal with a frequency proportional to the speed of the rotor is obtained at the sensor output. For measurements in dynamic conditions, a variable interval between...
-
NEW DESIGNS OF MAGNETIC FLUID SEALS FOR RECIPROCATING MOTION
PublikacjaT he operating conditions of magnetic fluid seals during reciprocating motion are so different from those observed in rotating motion that the use of their conventional structures for reciprocating motion seals yields no good results. The analysis of the sealing mechanism of magnetic fluid seals in reciprocating motion shows that the operation of these seals is affected by the carry-over phenomenon and magnetic fluid...
-
The methodology of design of axial clearances compensation unit in hydraulic satellite displacement machine and their experimental verification
PublikacjaA new methodology of calculating the dimensions of the axial clearance compensation unit in the hydraulic satellite displacement machine is described in this paper. The methods of shaping the compensation unit were also proposed and described. These methods were used to calculate the geometrical dimensions of the compensation field in an innovative prototype of a satellite hydraulic motor. This motor is characterized by the fact...
-
An Improved Method of Minimizing Tool Vibration during Boring Holes in Large-Size Structures
PublikacjaThe paper presents a thoroughly modified method of solving the problem of vibration suppression when boring large-diameter holes in large-size workpieces. A new approach of adjusting the rotational speed of a boring tool is proposed which concerns the selection of the spindle speed in accordance with the results of the simulation of the cutting process. This streamlined method focuses on phenomenological aspects and involves the...
-
Modele i algorytmy dla grafowych struktur defensywnych
PublikacjaW niniejszej pracy przeprowadzono analizę złożoności istnienia struktur defensywnych oraz równowag strategicznych w grafach. W przypadku struktur defensywnych badano modele koalicji defensywnych, zbiorów defensywnych i koalicji krawędziowych – każdy z nich w wersji globalnej, tj. z wymogiem dominacji całego grafu. W przypadku modeli równowagi strategicznej badano równowagę strategiczną koalicji defensywnych, równowagę strategiczną...
-
The role of analytical chemistry in the study of the Anthropocene
PublikacjaThe term “Anthropocene” refers to not yet formalized epoch of geologic time during which geologic processes have been dominated by the human impact. This impact takes on many forms. Biological, physical and chemical changes to the Earth System caused by anthropogenic activity are recorded in natural archives either as new fossil assemblages (neobiota), anthropogenic deposits or a wide variety of pollutants emitted to the environment....
-
THE ROLE OF THIN FUNCTIONAL LAYERS IN SOLID OXIDE FUEL CELLS
PublikacjaWidespread commercialization of solid oxide fuel cells requires lowering its cost. It is generally accepted that to lower the cost of solid oxide fuel cells it is necessary to use metal alloys as interconnectors and, consequently, lower its operating temperature to slow down interconnectors degradation. As a result the area specific resistance of the cathodes should be lowered to sustain the performance of the cells. In order to...
-
Determination of time dependence of coated metal electrical and electrochemical parameters during exposure using principal component analysis
PublikacjaThe use of the principal component analysis (PCA) permits the complex and quantitative analysis of the time dependence of electrical and electrochemical parameters of coated metal obtained by fitting impedance data. So far, changes in electrical and electrochemical parameters during exposure were analyzed independently. In this way, some of the information contained in the relationship between changes in parameters over time are...
-
Investigation of thin perovskite layers between cathode and doped ceria used as buffer layer in solid oxide fuel cells
PublikacjaIn this paper, thin perovskite layers between cathode material of solid oxide fuel cells and gadolinia-doped ceria buffer layer are investigated. Thin layers made of LaNi0.6Fe0.4O3-δ (LNF), La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF), or SrTi0.65Fe0.35O3-δ (STF) were symmetrically deposited by spin coating method from metallo-organic polymer precursors on a Ce0.8Gd0.2O2-δ (CGO) substrate. Porous and about 40-μm-thick LNF cathodes were deposited...
-
Biological and antibacterial properties of chitosan-based coatings with AgNPs and CuNPs obtained on oxidized Ti13Zr13Nb titanium alloy
PublikacjaDespite numerous studies, the antibacterial efficiency and cytotoxicity of chitosan-based coatings with nanometals need further studies. The purpose of this research was to determine the biological properties of chitosan coatings implemented with either silver nanoparticles (AgNPs) or copper nanoparticles (CuNPs), that were electrophoretically deposited on electrochemically oxidized Ti13Zr13Nb alloy. The SEM tests were used to...
-
Tuning of the plasmon resonance location in Au nanostructures coated with a ultrathin film of Al2O3 – Optical measurements and FDTD simulations
PublikacjaThe Au nanostructures have been coated with an ultra-thin films of amorphous aluminium oxide. Optical absorption spectra show the influence of the thickness of Al2O3 on plasmon resonance wavelength. The observed red-shift of the resonance location with the increase of the thickness of the Al2O3 film, can be explained by the change in the dielectric function of this film. It allows control of the optical spectra of the coated particles....
-
Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings
PublikacjaCold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...
-
Effectiveness of a dual surface modification of metallic interconnects for application in energy conversion devices
PublikacjaA dual surface modification of an SOFC metallic interconnect with a Gd2O3 layer and an MnCo2O4 coating was evaluated. The tested samples were oxidized for 7000 h in air at 1073 K. Oxidation products were characterized using XRD, SEM-EDS, and confocal Raman imaging, and ASR was measured. The effect of gadolinium segregation at grain boundaries in Cr2O3 was evaluated using S/TEM-EDS. Area specific-resistance was measured and fuel...
-
Electrophoretic Deposition and Characteristics of Chitosan–Nanosilver Composite Coatings on a Nanotubular TiO2 Layer
PublikacjaThe surface treatment of titanium implants has been applied mainly to increase surface bioactivity and, more recently, to introduce antibacterial properties. To this end, composite coatings have been investigated, particularly those based on hydroxyapatite. The present research was aimed at the development of another coating type, chitosan–nanosilver, deposited on a Ti13Zr13Nb alloy. The research comprised characterization of the...
-
Metal-Organic Framework (MOF)/Epoxy Coatings: A Review
PublikacjaEpoxy coatings are developing fast in order to meet the requirements of advanced materials and systems. Progress in nanomaterial science and technology has opened a new era of engineering for tailoring the bulk and surface properties of organic coatings, e.g., adhesion to the substrate, anti-corrosion, mechanical, flame-retardant, and self-healing characteristics. Metal-organic frameworks (MOFs), a subclass of coordinative polymers...
-
Stabilization of N-, N,N-, N,N'-Methylated and Unsubstituted Simple Amidine Salts by Multifurcated Hydrogen Bonds
PublikacjaIn the light of the usefulness of amidines in medicinal chem., this paper considers the effects on biol. properties and chem. reactivities of org. mols. affected by intramol. interactions. The study of chem. shifts has been an important source of information on the electronic structure of amidine salts and their ability to form non-covalent bonds with nucleic acids. The NMR and IR results demonstrate that hydrogen bonds are...
-
Interfacial adhesion evaluation in (low-density polyethylene)/elastomer blends
PublikacjaLow-density polyethylene (LDPE) with different elastomers at a ratio of 50/50 wt% blends was prepared by using a co-rotating twin-screw extruder. Three kinds of elastomers were used: ground tire rubber (GTR), partially crosslinked butyl rubber (KalarVR ), and styrenebutadiene- rubber block copolymer (SBS; KratonVR ). For better characterization of interaction between polyethylene and elastomer, influence of the type of elastomer on...
-
Curing characteristics, mechanical and thermal properties of reclaimed ground tire rubber cured with various vulcanizing systems
PublikacjaGround tire rubber was thermo-mechanical reclaimed at 120 °C using a co-rotating twin screw extruder. The effect of vulcanizing system type on curing characteristics, static mechanical properties (tensile strength, elongation-at-break, hardness and resilience), dynamic mechanical properties and thermal properties of reclaimed ground tire rubber was investigated. Reclaimed rubber was cured using different types of vulcanization...
-
Manufacture and research of TPS/PE biocomposites properties
PublikacjaIn this paper the process of native starch preparing for modification by extrusion and manufacture of biocomposites is presented. The first aim of this study was to determine the mixing and granulating condition of native starch to obtain granulated native starch. For mixing and granulation of native starch Intensive Mixer manufactured by Maschinenfabrik Gustav Eirich was used. Mixing and granulation in a single process is a new...
-
A Parallel MPI I/O Solution Supported by Byte-addressable Non-volatile RAM Distributed Cache
PublikacjaWhile many scientific, large-scale applications are data-intensive, fast and efficient I/O operations have become of key importance for HPC environments. We propose an MPI I/O extension based on in-system distributed cache with data located in Non-volatile Random Access Memory (NVRAM) available in each cluster node. The presented architecture makes effective use of NVRAM properties such as persistence and byte-level access behind...
-
QRS Morphology-Based EDR Signal—Factors Determining its Properties
PublikacjaRespiration-induced signals contain a clinically significant information. It could be obtained utilizing both direct and indirect methods. ECG-Derived Respiration (EDR) method is the latter one. However, in this case, two approaches could be distinguished. First one is based on determining changes in the morphology of QRS complexes while the second one is based on the Respiratory Sinus Arrhythmia (RSA) mechanism. The former approach...
-
A coupled constitutive model for fracture in plain concrete based on continuum theory with non-local softening and eXtended Finite Element Method
PublikacjaThe paper presents a constitutive model for concrete which combines a continuous and discontinuous fracture description. In a continuum regime, two different constitutive laws were used. First, a plasticity model with a Rankine failure criterion and an associated fl ow rule was used. Second, a constitutive law based on isotropic damage mechanics was formulated. In order to capture the width of a localized zone and to obtain mesh-independent...
-
Ocena przekształceń piętrowego, ceglanego domu z dachem półpłaskim z przełomu XIX–XX wieku pod wpływem termomodernizacji na przykładzie gminy Puck, woj. pomorskie.
PublikacjaCeglane budynki mieszkalne z przełomu XIX i XX wieku, które stanowiły charakterystyczny element krajobrazu wsi pomorskiej, obecnie powszechnie poddawane są modernizacji w celu poprawy warunków cieplnych. Przedmiotem badania jest stan zachowania najmłodszego, historycznego typu domuw zagrodzie chłopskiej na Kaszubach – piętrowego, ceglanego domu z dachem półpłaskim. Badanie przeprowadzono na obszarze gminy Puck. Zidentyfikowano...
-
Correlation between the Reactivity and Spectroscopic Properties of N-Substituted Secondary Thioamides. New Intramolecular N• •H+• •N Binding Approach and Proton Complexes Based on Thioamide Ligation
PublikacjaFrom a comparison of chem. shifts and wavenumbers of several secondary thioamides and amides having monocationic substituents attached to thiocarbamoyl or carbamoyl groups by a polymethylene chain, new intramol. unconventional N···H+···N H bonding effects were discovered. It is argued that the CH2-N rotation is hindered and two +H···NHMe nonequiv. protons occur in a proton spectrum of hydrochloride RCH2C(S)NH(CH2)3NHMe-HCl...
-
A novel method for drop in drop edible oils encapsulation with chitosan using a coaxial technique
PublikacjaThe presented work concerns a novel one step method for oil encapsulation. In this coaxial system the oil constitutes the core of the capsule, while the chitosan solution is the polymer shell surrounding the core to provide separation of the core from the external environment. The paper contains a diagram of the encapsulation equipment and explains the principle of its operation. The experimental results showed the impact of the...
-
Development of SPME fiber coatings with tunable porosity for physical confinement of ionic liquids as an extraction media
PublikacjaExtending the use of ionic liquids in sample preparation techniques remains a challenge. This paper presents procedures enabling the easy application of ionic liquids to the SPME technique. For this purpose, two approaches for producing a porous silica coating on a metal rod were investigated. Two silica precursor and porogen systems were used in the research: K2SiO3 + Formamide and Tetramethyl-orthosilicate + Polyethylene oxide....
-
Impact of low-temperature sintering on the Fe-based amorphous coatings
PublikacjaBulk metallic glasses (BMGs) have gained a lot of attention in recent years due to their outstanding properties such as high hardness and excellent wear and corrosion resistance. However, they are restricted in industrial applications due to their extreme brittleness. Iron based amorphous coatings from BMGs are the best solution to use them by overcoming the problem of extreme brittleness. The coatings can be sprayed by various...
-
Experimental review of the performances of protective coatings for interconnects in solid oxide fuel cells
PublikacjaFerritic stainless steel interconnects are used in solid oxide fuel cells; however, coatings are required to improve their performance. Although several types of coatings have been proposed, they have been scarcely investigated under similar conditions. This study compares the characteristics of uncoated Crofer 22 APU and eight different coatings on Crofer 22 APU for up to 3000 h at 800 ◦C. The coatings were deposited at various...
-
Surface effects of network materials based on strain gradient homogenized media
PublikacjaThe asymptotic homogenization of periodic network materials modeled as beam networks is pursued in this contribution, accounting for surface effects arising from the presence of a thin coating on the surface of the structural beam elements of the network. Cauchy and second gradient effective continua are considered and enhanced by the consideration of surface effects. The asymptotic homogenization technique is here extended to...
-
Nanocrystalline diamond sheets as protective coatings for fiber-optic measurement head
PublikacjaFiber-optic sensors find numerous applications in science and industry, but their full potential is limited because of the risk of damaging the measurement head, in particular, due to the vulnerability of unprotected tips of the fiber to mechanical damage and aggressive chemical agents. In this paper, we report the first use of a new nanocrystalline diamond structure in a fiber-optic measurement head as a protective coating of...
-
Changes on the Surface of the SiO2/C Composite, Leading to the Formation of Conductive Carbon Structures with Complex Nature of DC Conductivity
PublikacjaSol–gel layers have been the subject of many studies in recent decades. However, very little information exists about layers in which carbon structures are developed in situ. Using the spin-coating method, we obtained thin iron-doped SiO2/C composite films. The results of Raman spectroscopy showed that our samples consisted of graphitic forms and polymers. The latter’s contribution decreases with rising temperature. FTIR and EDS...
-
The site at the cape Zidine in Lopar in the context of coastal residential and commercial complexes of Rab Island
PublikacjaSince 2013, the “Archaeological topography of the island of Rab” project has approached the island’s archaeology holistically and interdisciplinary, tackling all periods and archaeological evidence present on the island. Nevertheless, mostly due to a large amount of new data, a significant segment of research is devoted to Roman residential and production complexes, located either in the island’s fields or along the coast. Thus,...
-
STUDIES ON THE USE OF TERRESTRIAL LASER SCANNING IN THE MAINTENANCE OF BUILDINGS BELONGING TO THE CULTURAL HERITAGE
PublikacjaWithin the frames of the use of terrestrial laser scanning we find numerous examples of registration of building facilities, including also historical and valuable in their culture. In the case presented in this paper, at the root of the problem there is a preservation of the historic blacksmith’s forge located in Gdansk Orunia. The facility dating from the early nineteenth century was intended to repair involving the complete...
-
Studies on the use of terrestrial laser scanning in the maintenance of buildings belonging to the cultural heritage
PublikacjaWithin the frames of the use of terrestrial laser scanning we find numerous examples of registration of building facilities, including also historical and valuable in their culture. In the case presented in this paper, at the root of the problem there is a preservation of the historic blacksmith's forge located in Gdansk Orunia. The facility dating from the early nineteenth century was intended to repair involving the complete...
-
Occurrence and levels of polybrominated diphenyl ethers (PBDEs) in house dust and hair samples from Northern Poland; an assessment of human exposure
PublikacjaPolybrominated diphenyl ethers (PBDEs) are among most ubiquitous compounds to be found in indoor environment and ingestion of household dust is considered an important route of exposure to PBDEs, especially in toddlers and young children. The present work reported concentration levels of PBDE congeners (PBDE-28, -47, -99, -100, -153, -154, -183 and -209) in hair and dust samples from selected households from Northern Poland. The...
-
Using the Fingerprinting Method to Customize RTLS Based on the AoA Ranging Technique
PublikacjaReal-time Locating Systems (RTLSs) have the ability to precisely locate the position of things and people in real time. They are needed for security and emergency applications, but also for healthcare and home care appliances. The research aims for developing an analytical method to customize RTLSs, in order to improve localization performance in terms of precision. The proposed method is based on Angle of Arrival (AoA), a ranging...
-
Linking optical and electronic properties to photoresponse of heterojunctions based on titania nanotubes and chromium, molybdenum, and tungsten oxides
PublikacjaThe development of photosensitization strategies for titanium dioxide is necessary for the enhancement of its optical and electronic properties towards its application potential in solar photoelectrochemistry. In this work, significant differences in the photosensitizing capability of the 6th group transition metal oxides applied on the surface of titania nanotubes are reported. For the first time, correlations between the experimentally...
-
New hybrid quadrature schemes for weakly singular kernels applied to isogeometric boundary elements for 3D Stokes flow
PublikacjaThis work proposes four novel hybrid quadrature schemes for the efficient and accurate evaluation of weakly singular boundary integrals (1/r kernel) on arbitrary smooth surfaces. Such integrals appear in boundary element analysis for several partial differential equations including the Stokes equation for viscous flow and the Helmholtz equation for acoustics. The proposed quadrature schemes apply a Duffy transform-based quadrature...
-
Hybridized Space-Vector Pulsewidth Modulation for Multiphase Two-Level Voltage Source Inverter
PublikacjaIn space vector pulsewidth modulation (SVPWM) algorithms for multiphase two-level voltage source inverters (VSI), the components of active vectors in all orthogonal spaces have to be calculated within the processor and stored in its memory. These necessitate intensive computational efforts of the processor and large memory space. This article presents a hybridized SVPWM for multiphase two-level VSI. In this algorithm, elements...
-
Determination of polybrominated diphenyl ethers (PBDEs) in dust samples collected in air conditioning filters of different usage – method development
PublikacjaThis study presents the results of studies aimed at the development of an analytical procedure for separation, identification, and determination of PBDEs compounds in dust samples collected from automotive cabin air filters and samples collected from filters installed as part of the air purification system in academic facilities. Ultrasound-assisted dispersive solid phase extraction (UA-dSPE) was found to perform better in terms...