Filtry
wszystkich: 1142
wybranych: 1000
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: VIBRATION SUPPRESSION
-
Numerical Evaluation of Dynamic Response of a Steel Structure Model under Various Seismic Excitations
PublikacjaThe present paper reports the results of the study, which was designed to perform a numerical evaluation of dynamic response of a single-storey steel structure model. The experimental model was previously subjected to a number of different earthquake ground motions during an extensive shaking table investigation. The analyzed structure model was considered as a 1-DOF system with lumped parameters, which were determined by conducting...
-
INFLUENCE OF SURFACE CURVATURE ON SESSILE DROPLET CONTACT ANGLE OF NANOFLUIDS
PublikacjaThis paper deals with change in contact angle of droplets of three nanofluids, i.e. water-Al2O3, water-TiO2 and water-Cu. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. Although dispersants were not used to stabilize the suspension, the solutions tested exhibited satisfactory stability. Ultrasonic vibration was used in order to stabilise the dispersion of the nanoparticles. Experimental measurements...
-
ASSESSMENT OF TOXIC EFFECT AND ENDOCRINE POTENTIAL OF FOOD PACKAGES EXTRACTS
PublikacjaIn the scientific literature related to the widely understood issue of packaging materials designed to have contact with food there is much information on raw materials used for their production, their physiochemical properties, types and parameters. There is also a great number of publications on the management and disposal of used packaging. Unfortunately, not much attention is given to the matters concerning migration of toxic...
-
Standing Acoustic Waves and Relative Nonlinear Phenomena in a Vibrationally Relaxing Gas-Filled Resonator
PublikacjaStanding acoustic waves in one-dimensional resonator filled with vibrationally relaxing gas, are studied. Two regimes of excitation of molecular vibrational degrees of freedom are considered, equilibrium and nonequilibrium. The acoustic energy enlarges with time in the non-equilibrium regime and decreases otherwise before formation of discontinuity. After that, it decreases due to nonlinear absorption and tends to zero in equilibrium...
-
Labour resources in Kazakhstan and Uzbekistan - a comparative study
PublikacjaThe aim of the paper is to show the transformation and comparison of labour resources in Kazakhstan and Uzbekistan using the following methods: deductive data analysis, observation of changes in the structure of resources based on publicly available macroeconomic data. During the two decades of the 21st century, both countries experienced population growth which translated into an increased number of persons of working age. In...
-
Labour resources in Azerbeijan
PublikacjaThe article aims to assess the changes of the Azerbaijani labour resources through deductive analysis of historical data and observation of changes in the structure of resources based on generally available macroeconomic data. Analysis shows that, during the period considered, the population of Azerbaijan increased, with a majority living in cities. Universal access to education enabled a growing group of Azerbaijanis to complete...
-
Cost-Efficient Design Methodology for Compact Rat-Race Couplers
PublikacjaIn this article, a reliable and low-cost design methodology for simulation-driven optimization of miniaturized rat-race couplers (RRCs) is presented. We exploit a two-stage design approach, where a composite structure (a basic building block of the RRC structure) is first optimized using a pattern search algorithm, and, subsequently, the entire coupler is tuned by means of surrogate-based optimization (SBO) procedure. SBO is executed...
-
Magneto-thermal convection of low concentration nanofluids
PublikacjaThe main aim of this paper was to analyze possible utilization of the low concentration nanofluids and the magnetic field to enhance heat transfer. The studied fluids were based on water with an addition of copper particles (40-60 nm diameter). They belonged to the diamagnetic group of materials. As a first attempt to stated target the analysis of enclosure placed in the maximal value of square magnetic induction gradient was carried...
-
Assessment of dynamic characteristics of thin cylindrical sandwich panels with magnetorheological core
PublikacjaBased on the equivalent single-layer linear theory for laminated shells, free and forced vibrations of thin cylindrical sandwich panels with magnetorheological core are studied. Five variants of available magnetorheological elastomers differing in their composition and physical properties are considered for smart viscoelastic core. Coupled differential equations in terms of displacements based on the generalized kinematic hypotheses...
-
The dynamic performance analysis of the Micro-turbine's rotor supparted on slide and roling element bearings
PublikacjaThis article presents the results of investigations of dynamic characteristics of a small-dimension rotor with slide and rolling element bearings. The object of investigations was the rotor-bearing system designed for the ORC based low-power steam micro-turbine. The investigations were performed using MESWIR series programs, as well as commercial FEA software ABAQUS and MADYN 2000. The results of modal analysis of the micro-rotor...
-
Experimental determination of dynamic properties of cylindrical steel tank model filled with liquid
PublikacjaIn technical branches, such as chemical or petroleum industries, cylindrical steel tanks are essential structures used for storage of liquid products. Any failure might have disastrous consequences, therefore their safety and reliability is essential. The aim of the present paper is to show the results of the experimental study which has been conducted on a scaled model of a real tank used in Poland. The investigation was carried...
-
EXPERIMENTAL STUDY OF A TEMPORARY STEEL GRANDSTAND UNDER CROWD LOAD
PublikacjaTemporary structures, such as grandstands, are commonly used during different types of mass events, especially sport and music concerts. In this paper, the results of the experimental study on temporary steel grandstand are presented. The aim of the investigation was to determine modal characteristics of such structures. Modes of free vibrations and corresponding natural frequencies have been obtained for empty and occupied grandstand....
-
Relieving the Measuring System of the Trailer for Tyre/Road Rolling Resistance Measurements from the Inertia Force
PublikacjaIn the article the principle of measuring of tyre/road rolling resistance tyres in road conditions applied in a special measuring trailer is presented. This trailer was built in Faculty of Mechanical Engineering at Gdansk University of Technology. The construction of two special devices used in this trailer was discussed. These devices eliminate the influence of some chosen confounding measurements factors such as: the inertia...
-
Simulation Environment in Python for Ship Encounter Situations
PublikacjaTo assess the risk of collision in radar navigation distance-based safety measures such as Distance at the Closest Point of Approach and Time to the Closest Point of Approach are most commonly used. Also Bow Crossing Range and Bow Crossing Time measures are good complement to the picture of the meeting situation. When ship safety domain is considered then Degree of Domain Violation and Time to Domain Violation can be applied. This...
-
Prediction of the fatigue lifetime of PUR structural elements using a combined experimental-numerical approach
PublikacjaThis paper presents a method for estimating the fatigue life of polyurethane elastomeric components. A rubber replacement - polyurethane of hardness 80ShA commonly used in vibration damping systems, for example, in motor vehicle suspensions, was used for the study. A metal-rubber bushing component was selected for analysis, and numerical analysis was carried out along with a fatigue model proposal based on a modification of the...
-
Structural Health Monitoring System for Suspension Footbridge
PublikacjaThe article presents the structural health monitoring (SHM) system installed in a footbridge in Radom. The main reason for the need for fitting of such a system was failed acceptance tests of the bridge. While under a dynamic load consisting of a group of 12 pedestrians jumping on the bridge, the bridge developed vibration during which acceleration of the deck of up to 4.5 m/s2 was recorded. Such behavior of the footbridge causes...
-
Development of a compact microstrip resonant cell aimed at efficient microwave component size reduction
PublikacjaA comprehensive comparison of a wide collection of compact microstrip resonant cells (CMRCs) found in the extensive body of literature has been presented. The evaluation of different CMRC designs has led to the selection of the most promising CMRC geometry for the efficient miniaturisation of modern microwave components. In order to showcase the vital effectiveness of the approach, the initially selected CMRC has been notably...
-
Further development of the poroelastic road surface within the new Polish project SEPOR
PublikacjaRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
Rearrangements of the nitrifiers population in an activated sludge system under decreasing solids retention times
PublikacjaDue to the key role of nitrite in novel nitrogen removal systems, nitrite oxidizing bacteria (NOB) have been receiving increasing attention. In this study, the coexistence and interactions of nitrifying bacteria were explored at decreasing solids retention times (SRTs). Four 5-week washout experiments were carried out in laboratory-scale (V=10 L) sequencing batch reactors (SBRs) with mixed liquor from two full-scale activated sludge...
-
Assessment of ecotoxicity and total volatile organic compound (TVOC) emissions from food and children's toy products
PublikacjaThe development of new methods for identifying a broad spectrum of analytes, as well as highly selective tools to provide the most accurate information regarding the processes and relationships in the world, has been an area of interest for researchers for many years. The information obtained with these tools provides valuable data to complement existing knowledge but, above all, to identify and determine previously unknown hazards. Recently,...
-
Measurement system for nonlinear surface spectroscopy by atomic force microscopy for corrosion processes monitoring
PublikacjaIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is especially useful for heterogeneous...
-
HYDROACOUSTIC NOISE MEASUREMENTS
PublikacjaThe paper deals mainly with investigation of underwater noise that propagation is in shallow water. In this paper has been presented the experimental investigation results concerning the distribution of the sound field pressure generated by moving ships in the shallow water at the small distance from the ship. The main acoustical characteristics describing features of the field are spectrograms in pseudo 3D system – distance and frequency...
-
Sessile droplet contact angle of water–Al2O3, water–TiO2 and water–Cu nanofluids
PublikacjaThis work presents measurements of the contact angle of sessile droplets for three nanofluids, i.e. water–Al2O3, water–TiO2 and water–Cu. The plates made of glass, anodized aluminium and stainless steel of different roughness served as substrates. Ultrasonic vibration was used for 30–60 min in order to stabilise the dispersion of the nanoparticles. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight....
-
Soil-structure interaction effects on modal parameters of office buildings with different number of stories
PublikacjaThe paper summarizes the results of a numerical investigation designed to study the soil-structure interaction effects on modal parameters of three office buildings. The reinforced-concrete 4-storey, 8-storey, and 12-storey office buildings, each with additional two levels of embedded basements, represent low, medium, and high-rise structures, respectively. In order to conduct this research, detailed finite-element structure models...
-
Experimental and numerical analysis of an aluminum cantilevered beam with polymer adhesive
PublikacjaIn this paper, experimental and numerical investigation on a composite cantilevered aluminum beam has been conducted. The subject of the study consists of two plain aluminum elements bonded with polymer adhesive of different thickness. It has been proven in the previous study that this kind of material has high damping properties. During an experimental investigation, value of damping ratios have been obtained. The aim of a numerical...
-
An analysis of domain-based ship collision risk parameters
PublikacjaAccording to a lot of contemporary research on ship collision avoidance the classic approach parameters – distance at closest point of approach (DCPA) and time to the closest point of approach (TCPA) – are not sufficient for estimating ship collision risk and for planning evasive manoeuvres. Consequently new measures are introduced, often utilizing the concept of a ship domain. Their drawback, up to this point, was the lack of...
-
Assessing groundwater vulnerability to pollution in the Puck region (denudation moraine upland) using vertical seepage method
PublikacjaDegradation of groundwater quality can cause a serious water supply and environmental problems. The identify of potential groundwater pollution can be determined by assessment of groundwater vulnerability method. The assessment of groundwater vulnerability to pollution was based on estimation of migration time of potential conservative contamination through the vadose zone. Area of investigation is a type of denudation moraine...
-
Accurate Post-processing of Spatially-Separated Antenna Measurements Realized in Non-Anechoic Environments
PublikacjaAntenna far-field performance is normally evaluated in expensive laboratories that maintain strict control over the propagation environment. Alternatively, the responses can be measured in non-anechoic conditions and then refined to extract the information on the structure field-related behavior. Here, a framework for correction of antenna measurements performed in non-anechoic test site has been proposed. The method involves automatic...
-
Corrosion Inhibition of Aluminium Alloy AA6063-T5 by Vanadates: Local Surface Chemical Events Elucidated by Confocal Raman Micro-Spectroscopy
PublikacjaChemical interactions between aqueous vanadium species and aluminium alloy AA6063-T5 were investigated in vanadate-containing NaCl solutions. Confocal Raman and X-ray photoelectron spectroscopy experiments were utilised to gain insight into the mechanism of corrosion inhibition by vanadates. A greenish-grey coloured surface layer, consisting of V+4 and V+5 polymerized species, was seen to form on the alloy surface, especially on...
-
Ab initio and density functional theory calculations of proton affinities for volatile organic compounds
PublikacjaThe Hatree-Fock method with 6-311G** split-valence molecular orbitals basis sets and the density function theory-B3LYP have been applied to geometrical optimizations and calculations of total electronic, zero point vibrational energies and proton affinities at 298 K for volatile organic compounds. Calculated values of proton affinities are compared with experimental data.
-
Active Control of Highly Autocorrelated Machinery Noise in Multivariate Nonminimum Phase Systems
PublikacjaIn this paper, a novel multivariate active noise control scheme, designed to attenuate disturbances with high autocorrelation characteristics and preserve background signals, is proposed. The algorithm belongs to the class of feedback controllers and, unlike the popular feedforward FX-LMS approach, does not require availability of a reference signal. The proposed approach draws its inspiration from the iterative learning control...
-
The modyfication of the dynamic characteristics of vibratory conveyor
PublikacjaThe vibratory conveyors are used in the industry for continuous transportation of loose substances on distance up to 20meters. These conveyors are often suspended on expensive and massive frames, which are softly vibroisolated from the ground. As a result, they transfer significant dynamic forces on the ground. In case of 5 - 20 meter-long devices, the biggest construction problems are proper vibrations of the panel caused by bilateral...
-
A measurement system for nonlinear surface spectroscopy with an atomic force microscope during corrosion process monitoring
PublikacjaIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is espe-cially useful for heterogeneous...
-
Reference FEM model for SHM system of cable-stayed bridge in Rzeszów
PublikacjaThe paper presents the references model for structural health monitoring system (SHM) of cable-stayed bridge recently constructed in Rzeszów over Wisłok River. The SHM system is design to provide on-line information on the structure state and facilitate its maintenance procedures. The main feature of the SHM system is permanent observation of the dynamic behavior of the bridge with focus on cable vibrations. The paper discusses...
-
Identification of Kinematic Excitation Function by the Modal Coordinates Estimation of the System's Dynamics
PublikacjaThe paper presents a method of the kinematic excitation courses’ identification in excitation points, based on the car road test acceleration at different measurement points. For the purpose of the laboratory fatigue life investigation of contemporary complex structures (e.g. cars bodies) and components of these structures (i.e. cars roofs), only a few first vibration modes are usually taken into account. During real life tests...
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublikacjaThe aim of the present paper is to show the results of the shaking table experimental study concerning the diagnosis of damage in a model of cylindrical steel tank with self-supported roof which is filled with liquid. During the tests, the base of the structure was excited under the harmonic loading with variable frequency. The tests were repeated for different stages of damage, which was introduced in the model by easing the bolts...
-
A Novel Approach to the Assessment of Cough Incidence
PublikacjaIn this paper we consider the problem of identication of cough events in patients suffering from chronic respiratory diseases. The information about frequency of cough events is necessary to medical treatment. The proposed approach is based on bidirectional processing of a measured vibration signal - cough events are localized by combining the results of forward-time and backward-time analysis. The signal is at rst transformed...
-
Badania wstępne możliwości oceny stanu powierzchni tocznej szyn za pomocą zjawisk wibroakustycznych
PublikacjaW artykule przedstawiono wstępną koncepcję możliwości wykorzystania zjawisk wibroa-kustycznych w celu oceny stanu powierzchni tocznych szyn. Scharakteryzowano metodykę, zakres badań oraz wybór punktów lokalizacyjnych. Badania wstępne obejmowały pomiary drgań i hałasu na referencyjnym odcinku toru oraz na odcinku toru z wadą squat. Pomiary przeprowadzono na dwóch liniach kolejowych nr 213 Reda – Hel oraz 131 Chorzów Batory – Tczew....
-
Using concentrated spectrogram for analysis of audio acoustic signals
PublikacjaThe paper presents results of time-frequency analysis of audio acoustic signals using the method of Concentrated Spectrograph also known as ''Cross-spectral method'' or ''Reassignment method''. Presented algorithm involves signal's local group delay and channelized instantaneous frequency to relevantly redistribute all Short-time Fourier transform lines in time-frequency plain. The main intention of the paper is to compare various...
-
The nonlinear effects of sound in a liquid with relaxation losses
PublikacjaThe nonlinear effects of sound in electrolyte with a chemical reaction are examined. The dynamic equations that govern non-wave modes in the field of intense sound are derived, and acoustic forces of vortex, entropy, and relaxation modes are determined in the cases of low-frequency sound and high-frequency sound. The difference in the nonlinear effects of sound in electrolyte and in a gas with excited vibrational degrees of molecules,...
-
DYNWIR S-70 program for modal analysis of multisupported and multimass rotors
PublikacjaThe article provides a brief description of the program Dynwir-S-70 (currently being developed in the Rotor Dynamics and Slide Bearings Department in the Institute of Fluid-Flow Machinery Polish Academy of Sciences in Gdansk) which is a program for analysis of multi-supported and multi-mass rotors. Used algorithms and the construction of mass and stiffness matrix were presented. Damping matrix structure based on Rayleigh damping...
-
The Influence of Camera and Optical System Parameters on the Uncertainty of Object Location Measurement in Vision Systems
PublikacjaThe article presents the influence of the camera and its optical system on the uncertainty of object position measurement in vision systems. The aim of the article is to present the methodology for estimating the combined standard uncertainty of measuring the object position with a vision camera treated as a measuring device. The identification of factors affecting the location measurement uncertainty and the determination of their...
-
Dynamic Response of the Suspended on a Single Cable Footbridge
PublikacjaThe article presents numerical simulations, dynamic in situ load tests and a structural health monitoring (SHM) system installed in a suspended on a single cable footbridge. Numerical simulations performed prior to construction indicated the possibility of structural dynamics problems, finally confirmed in the course of dynamic test loading. In the dynamic load course the bridge deck developed vibrations displaying accelerations...
-
System of monitoring of the Forest Opera in Sopot structure and roofing
PublikacjaThe authors present a solution realized in Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland) in connection with the modernization and construction of a new roof. The complicated structure of the roof of the facility and the used covering in form of membrane made of technical fabric required (for security reasons) to install the unit of devices allowing for the continuous geodetic monitoring of the facility. Monitoring...
-
Kinetics of Cross-Linking Reaction of Epoxy Resin with Hydroxyapatite-Functionalized Layered Double Hydroxides
PublikacjaThe cure kinetics analysis of thermoset polymer composites gives useful information about their properties. In this work, two types of layered double hydroxide (LDH) consisting of Mg2+ and Zn2+ as divalent metal ions and CO32− as an anion intercalating agent were synthesized and functionalized with hydroxyapatite (HA) to make a potential thermal resistant nanocomposite. The curing potential of the synthesized nanoplatelets in the...
-
Earthquake-induced pounding between equal height multi-storey buildings considering soil-structure interaction
PublikacjaThe present paper investigates the coupled effect of the supporting soil flexibility and pounding between neighbouring, insufficiently separated equal height buildings under earthquake excitation. Two adjacent three-storey structures, modelled as inelastic lumped mass systems with different structural characteristics, have been considered in the study. The models have been excited using a suit of ground motions with different peak...
-
Assessment of Failure Occurrence Rate for Concrete Machine Foundations Used in Gas and Oil Industry by Machine Learning
PublikacjaConcrete machine foundations are structures that transfer loads from machines in operation to the ground. The design of such foundations requires a careful analysis of the static and dynamic effects caused by machine exploitation. There are also other substantial differences between ordinary concrete foundations and machine foundations, of which the main one is that machine foundations are separated from the building structure....
-
A spline-based FE approach to modelling of high frequency dynamics of 1-D structures
PublikacjaIn this paper a computational methodology leading to the development of a new class of FEs, based on the application of continuous and smooth approximation polynomials, being splines, has been presented. Application of the splines as appropriately defined piecewise elemental shape functions led the authors to the formulation of a new approach for FEM, named as spFEM, where contrary to the well-known NURBS approach, the boundaries...
-
Nested Space Mapping Technique for Design and Optimization of Complex Microwave Structures with Enhanced Functionality
PublikacjaIn this work, we discuss a robust simulation-driven methodology for rapid and reliable design of complex microwave/RF circuits with enhanced functionality. Our approach exploits nested space mapping (NSM) technology, which is dedicated to expedite simulation-driven design optimization of computationally demanding microwave structures with complex topologies. The enhanced func-tionality of the developed circuits is achieved by means...
-
Principles and applications of Ligation Mediated PCR methods for DNA-based typing of microbial organisms
PublikacjaA significant number of DNA-based techniques has been introduced into the field of microorganisms’ characterization and taxonomy. These genomic fingerprinting methods were developed to detect DNA sequence polymorphisms by using general principles, such as restriction endonuclease analysis, molecular hybridization, and PCR amplification. In recent years, some alternative techniques based on ligation of oligonucleotide adapters before...