Wyniki wyszukiwania dla: MATCHED FILTERING
-
Fabrication and Study of BiNbO4 Ceramics
PublikacjaAim of the present research was to fabricate and study crystalline structure as well as dielectric properties of BiNbO4 ceramics. In the present study BiNbO4 ceramics was fabricated by solid state reaction from the mixture of simple oxides viz. Bi2O3, and Nb2O5. Stoichiometric mixture of the powders was thermally analyzed so parameters of the thermal treatment were determined. The EDS measurements proved conservation of the chemical...
-
Comparison of noise reduction methods in radiometric correlation measurements of two-phase liquid-gas flows
PublikacjaTwo-phase liquid-gas flows occur frequently in the mining, energy, chemical, and petrochemical industries. One of non-contact methods used to analyse these flows is the gamma ray absorption method. However, the signals received from radiation detectors contain a significant stochastic noise, which makes them difficult to analyse. The article describes four methods of noise reduction in cross-correlation measurements of water-air...
-
Selection of C-Type Filters for Reactive Power Compensation and Filtration of Higher Harmonics Injected into the Transmission System by Arc Furnaces
PublikacjaThis article presents a method for selecting the elements of a C-type filter working with a conventional LC-type filter for compensating reactive power and filtering out higher harmonics generated by arc furnaces and ladle furnaces. The study was conducted in a steel mill supplied by a 110 kV transmission system, where higher harmonic currents and nonlinear loads were measured. A series of computer simulations were performed under...
-
ZASTOSOWANIE FILTRACJI CZĄSTECZKOWEJ DO ESTYMACJI POŁOŻENIA W SYSTEMIE LOKALIZACYJNYM UWB
PublikacjaNiniejszy artykuł dotyczy kwestii poprawy dokładności estymacji położenia w systemie lokalizacji wewnątrzbudynkowej, bazującym na radiowych pomiarach odległości realizowanych przez modemy UWB. Proponuje się zastosowanie metody filtracji cząsteczkowej do zmniejszenia błędu wyznaczania pozycji obiektu przy braku bezpośredniej widoczności ze stacją referencyjną. W artykule opisano algorytm filtru cząsteczkowego, jego przykładową implementację...
-
Dynamic ranking of cloud providers
PublikacjaThe paper focuses on how to create an effective dynamic ranking service for IaaS,PaaS and SaaS cloud providers. It considers building of a quality model for thispurpose along with definition of quality measurement procedures. The paper discussesseveral techniques known from already existing price comparison engines that couldbe modified and adopted for comparison of cloud providers. Furthermore, a tech-nique for filtering measured...
-
Area specific resistance (at 800 °C - 500 °C) of the SrTi0.50Fe0.50O3 porous oxygen electrodes sintered at different temperatures
Dane BadawczeIn this dataset are presented results of the polarization resistance of differently sintered SrTi0.50Fe0.50O3 porous oxygen electrodes in symetrical cell. Applied sintering temperatures were 900 °C, 950 °C and 1000 °C. The measurement temperature range was between 800 °C and 500 °C with synthetic air flow (21% O2, 40 ml min-1). Results converted to...
-
Area specific resistance (at 800 °C - 500 °C) of the SrTi0.30Fe0.70O3 porous oxygen electrodes sintered at different temperatures
Dane BadawczeIn this dataset are presented results of the polarization resistance of differently sintered SrTi0.30Fe0.70O3 porous oxygen electrodes in symetrical cell. Applied sintering temperatures were 900 °C, 950 °C and 1000 °C. The measurement temperature range was between 800 °C and 500 °C with synthetic air flow (21% O2, 40 ml min-1). Results converted to...
-
Area specific resistance (at 800 °C - 500 °C) of the SrTi0.65Fe0.35O3 porous oxygen electrodes sintered at different temperatures
Dane BadawczeIn this dataset are presented results of the polarization resistance of differently sintered SrTi0.65Fe0.35O3 porous oxygen electrodes in symetrical cell. Applied sintering temperatures were 900 °C, 950 °C and 1000 °C. The measurement temperature range was between 800 °C and 500 °C with synthetic air flow (21% O2, 40 ml min-1). Results converted to...
-
Mateusz Marchel dr inż.
Osoby -
efficient fractional delay hilbert transform filter in the farrow structure
PublikacjaIn this paper the design and application of a Fractional Delay Hilbert Transform Filter (FDHTF) into an adaptive sub-sample delay estimation between two separated sinusoidal signals is considered. The FDHTF incorporates the functions of Hilbertian and variable fractional delay filtering of the incoming signal simultaneously, in one stage. In traditional approach each of these operations was performed separately. Obtained value...
-
ESTIMATION OF NONSTATIONARY HARMONIC SIGNALS AND ITS APPLICATION TO ACTIVE CONTROL OF MRI NOISE
PublikacjaA new adaptive comb filtering algorithm, capable of tracking the fundamental frequency and amplitudes of different frequency components of a nonstationary harmonic signal embedded in white measurement noise, is proposed. Frequency tracking characteristics of the new scheme are studied analytically, proving (under Gaussian assumptions and optimal tuning) its statistical efficiency for quasi-linear frequency changes. Laboratory tests...
-
CGO as a barrier layer between LSCF electrodes and YSZ electrolyte fabricated by spray pyrolysis for solid oxide fuel cells
PublikacjaPerovskite La0.6Sr0.4Co0.2Fe0.8O3 − δ (LSCF) is often used as a cathode material for solid oxide fuel cells (SOFC) due to high mixed ionic and electronic conductivity and good catalytic activity. Unfortunately, sintering of the LSCF cathode together with the yttria stabilized zirconia (YSZ) electrolyte, leads to formation of the La2Zr2O7 and SrZrO3 phases in the interface. These phases increase the resistance of the cell. To avoid...
-
X-RAY DIFFRACTION STUDY OF BISMUTH LAYER-STRUCTURED MULTIFERROIC CERAMICS
PublikacjaGoal of the present research was to apply a solid state reaction route to fabricate bismuth layer-structured multiferroic ceramics described with the formula Bi5FeTi3O15 and reveal the influence of processing conditions on its crystal structure and phase composition. Simple oxide powders Bi2O3, TiO2 and Fe2O3 were used to fabricate Aurivillius-type bismuth layer-structured ferroelectrics. Pressureless sintering in ambient air was...
-
Evaluation of high-frequency roughness measurement errors for composite and ceramic surfaces after machining
PublikacjaPrecise characterisation of surface topography is of the greatest importance since many factors directly affect the accuracy of the whole measurement process. In this paper, the variety of surface topographies from machined composite and ceramic workpieces was studied with a special emphasis on the measurement results. Surfaces were subjected to the ground diamond, honing and milling processes. Measurement results were analysed...
-
Application of Complementary Signals in Built-In Self Testers for Mixed-Signal Embedded Electronic Systems
PublikacjaThis paper concerns the implementation of shape-designed complementary signals (CSs), matched to the frequency characteristic of the circuit under test, in built-in self testers (BISTs), dedicated to mixed-signal embedded electronic systems for testing their analog sections. The essence of the proposed method and solution of CS BIST is low-cost realization on the base of hardware and software resources of microcontrollers used...
-
Design and experimental verification of multi-layer waveguide using pin/hole structure
PublikacjaThis study presents a novel technique for minimizing RF leakage in metallic hollow waveguides fabricated using the multilayer split-block method. By integrating a pin/hole wall into the split-block multilayers, a substantial reduction of RF leakage can be achieved while reducing the circuit size and mitigating the performance variations. To validate the proposed approach, a slot antenna fed by single ridge waveguide has been prototyped...
-
Calculation of Resonance in Planar and Cylindrical Microstrip Structures Using a Hybrid Technique
PublikacjaA hybrid technique was employed for the analysis of the resonance frequency of thin planar and cylindrical microstrip structures with the patches of arbitrary geometry. The proposed technique utilizes a combination of Galerkin’s moment method and a finite-element method (FEM). In this approach, an FEM is adopted to calculate the patch surface current densities, and a method of moments is utilized to calculate the resonance frequencies...
-
A simple way of increasing estimation accuracy of generalized adaptive notch filters
PublikacjaGeneralized adaptive notch filters are used for identification/tracking of quasi-periodically varying dynamic systems and can be considered an extension, to the system case, of classical adaptive notch filters. It is shown that frequency biases, which arisein generalized adaptive notch filtering algorithms, can be significantly reduced by incorporating in the adaptive loop an appropriately chosen decision delay. The resulting performance...
-
SEM images of symmetrical cell interface with Sr1.05Ti0.30Fe0.70O3-d electrodes and CGO-20 substrate sintered at 800 °C, 900 °C and 1000 °C
Dane BadawczeThis dataset contains images of polished cross section of symmetrical cell interface with Sr1.05Ti0.30Fe0.70O3-d electrodes and CGO-20 substrate sintered at three different temperatures 800 °C, 900 °C and 1000 °C. Images were obtained using a PhenomXL (Thermo Fisher Scientific, the Netherlands) scanning electron microscope (SEM) with an accelerating...
-
SEM images of symmetrical cell interface with Sr1.00Ti0.30Fe0.70O3-d electrodes and CGO-20 substrate sintered at 800 °C, 900 °C and 1000 °C
Dane BadawczeThis dataset contains images of polished cross section of symmetrical cell interface with Sr1.00Ti0.30Fe0.70O3-d electrodes and CGO-20 substrate sintered at three different temperatures 800 °C, 900 °C and 1000 °C. Images were obtained using a PhenomXL (Thermo Fisher Scientific, the Netherlands) scanning electron microscope (SEM) with an accelerating...
-
SEM images of symmetrical cell interface with Sr0.90Ti0.30Fe0.70O3-d electrodes and CGO-20 substrate sintered at 800 °C, 900 °C and 1000 °C
Dane BadawczeThis dataset contains images of polished cross section of symmetrical cell interface with Sr0.90Ti0.30Fe0.70O3-d electrodes and CGO-20 substrate sintered at three different temperatures 800 °C, 900 °C and 1000 °C. Images were obtained using a PhenomXL (Thermo Fisher Scientific, the Netherlands) scanning electron microscope (SEM) with an accelerating...
-
SEM images of symmetrical cell interface with Sr0.95Ti0.30Fe0.70O3-d electrodes and CGO-20 substrate sintered at 800 °C, 900 °C and 1000 °C
Dane BadawczeThis dataset contains images of polished cross section of symmetrical cell interface with Sr0.95Ti0.30Fe0.70O3-d electrodes and CGO-20 substrate sintered at three different temperatures 800 °C, 900 °C and 1000 °C. Images were obtained using a PhenomXL (Thermo Fisher Scientific, the Netherlands) scanning electron microscope (SEM) with an accelerating...
-
W-like bound entangled states and secure key distillation
PublikacjaWe construct multipartite entangled states with underlying W-type structuresatisfying positive partial transpose (PPT) condition under any (N −1)|1 partition. Then we showhow to distill a N-partite secure key from the states using two different methods: direct applicationof local filtering and novel random key distillation scheme in which we adopt the idea from recentresults on entanglement distillation. Open problems and possible...
-
Topology Discovery of Hierarchical Ethernet LANs without SNMP support
PublikacjaThis paper presents an algorithm that allows for discovery of layer-2 hierarchical Ethernet network topology using agents running on selected end nodes. No SNMP, MIB, hardware, firmware, or operating system-level software modification is required. The method is based on transmission of customized Ethernet frames among installed software agents. It can be used to discover the topology of LAN or one VLAN segment as long as no MAC...
-
Conducted EMI Propagation Paths in DC-AC Hard Switching Converter
PublikacjaIn order to limit the electromagnetic interference (EMI) in power electronics devices, knowledge about the phenomena connected with EMI generation and propagation is necessary. This papers describes the propagation paths in the 3 phase voltage source inverter using wide-band simulation and laboratory test with the signal processing method Wiener filtering, where the transfer functions between voltage across switches and the perturbation...
-
The Concept of Geodetic Analyses of the Measurement Results Obtained by Hydrostatic Leveling
PublikacjaThe article discusses the issue of hydrostatic leveling. Its application is presented in structural health monitoring systems in order to determine vertical displacements of controlled points. Moreover, the article includes a complete computation scheme that utilizes the estimation from observation differences, allowing the elimination of the influence of individual sensors’ systematic errors. The authors suggest two concepts of...
-
Square Root Raised Cosine Fractionally Delaying Nyquist Filter - Design and Performance Evaluation
PublikacjaIn this paper we propose a discrete-time FIR (Finite Impulse Response) filter which is applied as a square root Nyquist filter and fractional delay filter simultaneously. The filter enables to substitute for a cascade of square root Nyquist filter and fractional delay filter in one device/algorithm. The aim is to compensate for transmission delay in digital communication system. Performance of the filter as a matched filter is...
-
Information-driven network resilience: Research challenges and perspectives
PublikacjaInternet designed over 40 years ago was originally focused on host-to-host message delivery in a best-effort manner. However, introduction of new applications over the years have brought about new requirements related with throughput, scalability, mobility, security, connectivity, and availability among others. Additionally, convergence of telecommunications, media, and information technology was responsible for transformation...
-
Mg2+ Doping Effects on the Structural and Dielectric Properties of CaCu3Ti4O12 Ceramics Obtained by Mechanochemical Synthesis
PublikacjaIn this study, ceramic CaCu3Ti4O12 (CCTO) and CaCu3−xMgxTi4O12 solid solutions in which 0.1 ≤ x ≤ 0.5 were prepared by the mechanochemical method, realized by a high‐energy ball milling technique. The effects of the Mg2+ ion concentration and sintering time on the dielectric response in the prepared ceramics were investigated and discussed. It was demonstrated that, by the use of a sufficiently high energy of mechanochemical treatment,...
-
Sensorless predictive control of three-phase parallel active filter
PublikacjaThe paper presents the control system of parallel active power filter (APF) with predictive reference current calculation and model based predictive current control. The novel estimator and predictor of grid emf is proposed for AC voltage sensorless operation of APF, regardless of distortion of this voltage. Proposed control system provides control of APF current with high precision and dynamics limited only by filter circuit parameters....
-
Miniaturized Metal-Mountable U-shaped Inductive-Coupling-Fed UHF RFID Tag Antenna with Defected Microstrip Surface
PublikacjaThis study presents a novel miniature ultra-high frequency (UHF) radio frequency identification (RFID) tag for metallic objects. Its arrangement includes a U-shaped feeder, which is inductively coupled to two E-type connected patches. Size reduction is achieved by means of utilizing the U-shaped feeder, and introducing a defection in the connection between the two E-type patches. The defection in the connection area between the...
-
Context-aware User Modelling and Generation of Recommendations in Recommender Systems
PublikacjaRecommender systems are software tools and techniques which aim at suggesting new items that may be of interest to a user. This dissertation is focused on four problems in recommender systems domain. The first one is context-awareness, i.e. how to obtain relevant contextual information, how to model user preferences in a context and use them to make predictions. The second one is multi-domain recommendation, which aim at suggesting...
-
Generalized adaptive notch smoothing revisited
PublikacjaThe problem of identification of quasi-periodically varying dynamic systems is considered. This problem can be solved using generalized adaptive notch filtering (GANF) algorithms. It is shown that the accuracy of parameter estimates can be significantly increased if the results obtained from GANF are further processed using a cascade of appropriately designed filters. The resulting generalized adaptive notch smoothing (GANS) algorithm...
-
Face Recognition: Shape versus Texture
PublikacjaThis paper describes experiments related to the application of well-known techniques of the texture feature extraction (Local Binary Patterns and Gabor filtering) to the problem of automatic face verification. Results of the tests show that simple image normalization strategy based on the eye center detection and a regular grid of fiducial points outperforms the more complicated approach, employing active models that are able to...
-
Estimation of the angular position of a two-wheeled balancing robot using a real IMU with selected filters
PublikacjaA low-cost measurement system using filtering of measurements for two-wheeled balancing robot stabilisation purposes has been addressed in this paper. In particular, a measurement system based on gyroscope, accelerometer, and encoder has been considered. The measurements have been corrected for deterministic disturbances and then filtered with Kalman, α-β type, and complementary filters. A quantitative assessment of selected filters...
-
Nierówności pionowe toru kolejowego
PublikacjaOcena jakości geometrycznej toru kolejowego wymaga od zarządców infrastruktury stosowania jednolitych metod pomiarów, obliczania i interpretacji wyników. W tym zakresie należy stosować się do norm europejskich i technicznych specyfikacje interoperacyjności. W artykule przedstawiono podstawowe zagadnienia związane z pomiarem i oceną nierówności pionowych toru kolejowego. Zapisano odchyłki dopuszczalne nierówności pionowych według...
-
Application of Microextraction Techniques Including SPME and MESI to the Thermal Degradation of Polymers: A Review
Publikacja -
Ekranowanie pola magnetycznego w cylindrycznych układach uwarstwionych
PublikacjaW pracy przeprowadzono analizę ekranowania pola magnetycznego w cienkościennych, cylindrycznych układach uwarstwionych. Obliczenia numeryczne wykonano w programie MathCad 14 metodą różnic skończonych stosując algorytm Cranka-Nicholsona.
-
Using Alpha-beta filtration for robustness improvement of a quadrocopter positioning system
PublikacjaQuadrocopter is an unmanned aerial vehicle (UAV) platform. The position of the robot is determined based on readings from an accelerometer and a gyroscope, but the measurement signals contain broadband noise. This article describes a solution for filtering out the noise based on an Alpha – beta filter. It also presents the methodology of designing and implementing such a filter for noise cancellation in measurement signals from...
-
Improvement of time difference of arrival measurements resolution by using fractional delay filters in a direct sequence-code division multiple access radionavigation system
PublikacjaThis study presents a method of improving time measurements resolution in a direct sequence-code division multiple access receiver by using a fine code tracking loop based on fractional delay filtering of a despreading sequence. It briefly describes the structure of a generic digital code tracking loop and the proposed modification which allows to measure time difference of arrival values with the subsample resolution, together...
-
Ancillary services to grids provided with distributed generation
PublikacjaThe paper introduces system for utilization of the customer-side generated energy. Additionally system can secure some ancillary services to grids. Those services include: current active filtering, load voltage stabilization and in case of grid voltage faults - uninterruptible load supplying (possible with energy storage device). Presented experimental results confirm flexibility of this arrangement in processes of power delivery...
-
An adaptive approach to non-destructive evaluation (NDE) of cast irons containing precipitated graphite particles with the help of magnetoacoustic emission
PublikacjaPhysical properties of cast irons strongly depend on both their microstructure and the presence of casting defects. The paper analyses the possibility of application of magnetoacoustic emission (MAE) for nondestructive detection of flawed cast iron components. The investigated samples containing dross, chunky graphite and lamellar graphite were compared with the reference, flawless, spheroidal cast iron sample. The optimisation...
-
HOW TO ASSESS THE MATURITY OF SMALL AND MEDIUM-SIZED ENTERPRISES TO LEAN SIX SIGMA PROJECTS
PublikacjaThis article describes the considerations for the implementation of the Lean Six Sigma (LSS) methodology in small and medium-sized enterprises. Pilot research was conducted in Polish and French SMEs (nine Polish and nine French enterprises from the service and production sectors) referring to the context of the implementation and application of the Lean Six Sigma concept. The studies led to the identification of the motives, needs,...
-
Design of a Coplanar Waveguide-Fed Wideband Compact-Size Circularly Polarized Antenna and polarization-sense alteration
PublikacjaThis paper presents the design and validation of a geometrically simple circularly polarized(CP) structure featuring flat gain in the sub-6 GHz 5th generation spectrum. The proposed structure is based on coplanar-waveguide-fed, modified wide slot etched in the ground plane. For generating CP waves, the coplanar ground planes are designed with slight asymmetry in both the horizontal and vertical directions. Furthermore, the ground...
-
The structure of the control system for a dynamically positioned ship
PublikacjaThe article discusses functions and tasks of dynamic positioning (DP) systems for ships. The analysed issues include ship steering, in particular stabilisation of ship position and direction of motion (real course) at low manoeuvring speeds, and commonly used DP ship models. Requirements imposed by classification societies on DP ships are quoted. A multi-layer structure of the DP control system is presented, with special attention...
-
New Algorithms for Adaptive Notch Smoothing
PublikacjaThe problem of extraction/elimination of a nonstationary complex sinusoidal signal buried in noise is considered. This problem is usually solved using adaptive notch filtering (ANF)algorithms. It is shown that accuracy of signal estimation can be increased if the results obtained from ANF are further processed using a cascade of appropriately designed filters. The resulting adaptive notch smoothing (ANS) algorithms can be employed...
-
FIReWORK: FIR Filters Hardware Structures Auto-Generator
PublikacjaThe paper presents application called FIReWORK, that allows for automatic creation of the VHDL hardware structures of FIR filters. Automat- ically generated specialized hardware solutions dedicated to the FPGA and ASIC are commonly known as Intellectual Property Cores. The essential fu- ture of the application is easy initialization of FIR filter parameters in GUI, and then automatically design, calculate and generate the IP Core...
-
Identification of quasi-periodically varying systems with quasi-linear frequency changes
PublikacjaThe problem of identification of linear quasi-periodically varying systems is considered. This problem can be solved using generalized adaptive notch filtering (GANF) algorithms. It is shown that accuracy of system parameter estimation can be increased if the results obtained from GANF are further processed using a cascade of appropriately designed filters. The resulting generalized adaptive notch smoothing (GANS) algorithms can...
-
Improving Re-rankCCP with Rules Quality Measures
PublikacjaRecommender Systems are software tools and techniques which aim at suggesting new items that may possibly be of interest to a user. Context-Aware Recommender Systems exploit contextual information to provide more adequate recommendations. In this paper we described a modification of an existing contextual post-filtering algorithm which uses rules-like user representation called Contextual Conditional Preferences. We extended the...
-
Control design for slow speed positioning
PublikacjaThe problem under study is a synthesis of position and heading control system for low frequency model of surface vessel described by 3 DOF mathematical model. The recursive vectorial backstepping control design was used to keep fixed position and heading in presence of wave disturbances. The controller has been simulated on computer model of scaled supply vessel. It has been assumed that the actuators produce generalized forces...