Wyszukiwarka
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: FRICTION RESISTANCES
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #28 - #29.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #28 (upper, rotating), #29 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #26 - #27.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #26 (upper, rotating), #27 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublikacjaNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
Increasing the Oxidative Stability of the Wafer Lipid Fraction with Fruit Extract during Storage
Publikacja -
Improved model of void fraction distribution in two-phase flow in the boundary layer
PublikacjaPraca skupiona jest na eksperymentalnej weryfikacji sił działających na pęcherzyk gazowy przepływający wzdłuż ścianki kanału, a następnie implementacji uzyskanych wyników do zaproponowanego wczesniej przez jednego z współautorów modelu rozkładu stopnia zapełnienia w warstwie przyściennej przepływu dwufazowego. Podczas badań pęcherzyk modelowany był sztywną kulą podwieszoną na strunie. Autorzy przekonują, że pokazany model dobrze...
-
Direct determination of cadaverine in the volatile fraction of aerobically stored chicken breast samples
PublikacjaTo supplement the currently used methods for poultry meat shelf life assessment, it might be necessary to develop a technique for rapid headspace analysis of volatiles with no prior sample preparation step. Biogenic amines, in particular cadaverine, are considered meat spoilage indicators. Described in this article are the results of a preliminary investigation of the applicability of proton transfer reaction mass spectrometry...
-
DETERMINATION OF SP3 FRACTION IN ta-C COATING USING XPS AND RAMAN SPECTROSCOPY
PublikacjaThe paper presents results of studies on the structure of tetrahedral amorphous carbon films (ta-C) with a thickness in the range from 20 to 280 nm, deposited using pulsed vacuum arc technique with an electromagnetic Venetian blind plasma filter. The results of the phase structure analysis, obtained using visible Raman spectroscopy and UV Raman spectroscopy methods, showed a strong dependence of the results on the presence, on...
-
PTR-MS and electronic nose application for volatile fraction analysis of cigar tobacco
PublikacjaCigar consumers attach great importance to the quality of these products. At the same time, cigars are often expensive, so destructive analytical methods of quality control are not being desired. However, it has been found that there are many volatile organic compounds in their headspace. Because of that, proton transfer reaction–mass spectrometry and electronic nose were used to analyse it. The obtained results were used to distinguish...
-
Phosphorus and nitrogen forms in liquid fraction of digestates from agricultural biogas plants
PublikacjaThe novelty of the presented research is the determination of the nitrogen and phosphorus fraction in the liquid fraction of digestate from agricultural biogas plants. This information is important because it can help in proposing possible further liquid fraction management or developing of new technologies for their purification. The research covered digestates from agricultural biogas plants, obtained from the fermentation of...
-
Piotr Jaskuła dr hab. inż.
OsobyI am a Faculty member (Associate Professor, Highway and Transportation Research Department) at the Faculty of Civil and Environmental Engineering, Gdansk University of Technology, Poland).My main research interests include: pavement structures, interlayer bonding, pavement materials, recycling of road pavements, asphalt mixtures, bitumens, construction and maintenance of pavement structures.My lectures at the University include:...
-
Infection and Drug Resistance
Czasopisma -
On parameter derivatives of the associated Legendre function of the first kind (with applications to the construction of the associated Legendre function of the second kind of integer degree and order)
PublikacjaZnaleziono cztery nowe wyrażenia dla pochodnej stowarzyszonej funkcji Legendre'a pierwszego rodzaju względem jej stopnia w przypadku, gdy rząd i stopień są liczbami naturalnymi. Wyniki wykorzystano do podania nowych wyrażeń dla stowarzyszonych funkcji Legendre'a drugiego rodzaju z naturalnymi rzędem i stopniem.
-
Laser Surface Treatment of Sintered Stainless Steels for Wear Resistance Enhancement
Publikacja -
Experimental analysis of coefficients of local resistance on elbows in multilayer pipe systems
Publikacja -
Modus operandi of Qatar Resistance Policy against “Anti-Terror Quartet”
Publikacja -
Quantitative proteomic analysis of anticancer drug RH1 resistance in liver carcinoma
Publikacja -
Increasing the frost resistance of ‘Golden Delicious’, ‘Gala’ and ‘Šampion’ apple cultivars
Publikacja -
The relationships between asphalt mix rutting resistance and MSCR test results
PublikacjaW publikacji przedstawiono badania wpływu rodzaju asfaltu na odporność i deformacje. Wykazano, że w przypadku betonów asfaltowych jest lepsza korelacja pomiędzy cechami asfaltów a odpornością na deformacje niż w przypadku mieszanek mineralno-asfaltowych o nieciągłym uziarnieniu.
-
Mechanisms of azole resistance among clinical isolates of Candida glabrata in Poland
PublikacjaCandida glabrata is currently ranked as the second most frequently isolated aetiological agent of human fungal infections, next only to Candida albicans. In comparison with C. albicans, C. glabrata shows lower susceptibility to azoles, the most common agents used in treatment of fungal infections. Interestingly, the mechanisms of resistance to azole agents in C. albicans have been much better investigated than those in C. glabrata....
-
Rolling Resistance And Tire/Road Noise on Rubberized Asphalt Pavement In Poland
PublikacjaThe paper presents results of tire/road noise and rolling resistance measurements performed on stone-matrix asphalt (SMA) that contains rubberized asphalt developed and produced by the company in Poland. Bituminous binder was modified with polymer and additive of crumb rubber. First observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger car...
-
Experimental determination of useful resistance value during pasta dough kneading
Publikacja -
The effects of resistance training experience on movement characteristics in the bench press exercise
Publikacja -
Tests on lateral resistance in railway track during operation of tamping machine
PublikacjaArtykuł prezentuje koncepcję prowadzenia badań oporów poprzecznych w trakcie procesu regulacji geometrycznej toru kolejowego za pomocą podbijarki. Jest to zatem kontynuacja badań nad zastosowaniem podbijarki torowej w diagnostyce toru bezstykowego; wcześniej zajmowano się kwestią określania sił podłużnych w szynach. Przedstawiono sposób wyznaczania oporów poprzecznych polegający na ciągłej rejestracji przemieszczenia oraz siły...
-
Identification and antimicrobial resistance of Enterococcus spp. isolated from surface water
PublikacjaIn the study species distributions and antimicrobial resistance profiles were determined among riverine Enterococcus spp. Susceptibility of the isolates was tested against: ampicillin, imipenem, teicoplanin, vancomycin, erythromycin, linezolid, fosfomycin, ciprofloxacin,levofloxacin, moxifloxacin, tetracycline, high levels of gentamicin and streptomycin. The enterococci were detected in all of the analyzed water samples, periodically...
-
Direct cloning of heavy metal resistance genes from metagenomic DNA
Publikacja -
Analysis of the Impact Resistance of Toecaps by the Finite Element Method: Preliminary Studies
Publikacja -
Exposure to Quaternary Ammonium Compounds Selects Resistance to Ciprofloxacin in Listeria monocytogenes
Publikacja -
Polymer based thick films - material quality and interface resistance evaluation
PublikacjaThe properties of polymer based thick film layers mede using different resistive pastes and dipping silvers have been studied. The composite of carbon and graphite (C/Gr) conducting particles suspended in different polymer vehicles were used for preparation resistive layers. Interface resistance Rc created between dipping silver (DiAg) contact layer and resistive layer was determined from the surface potential distribution measurements...
-
Resistance Training with Blood Flow Restriction and Ocular Health: A Brief Review
Publikacja -
Human proteinase 3 resistance to inhibition extends to alpha‐2 macroglobulin
Publikacja -
Effect of laser treatment on the wear and corrosion resistance of aluminiumalloy used for pistons
PublikacjaPrzedstawiono wpływ powierzchniowego laserowego przetapiania w warunkach kriogenicznych na skład chemiczny, mikrostrukturę, mikrotwardość oraz zużycie ścierne i odporność korozyjną stopu AlSi13Mg1CuNi stosowanego na tłoki silników spalinowych. Uzyskano zwiększenie odporności na ścieranie i korozję stopu AlSi13Mg1CuNi.
-
What about the multidrug resistance in fungi? - comparison of voriconazole and ''old'' azoles.
PublikacjaPorównano wyniki oznaczeń aktywności przeciwgrzybowej voriconazolu- nowego leku przeciwgrzybowego z pierścieniem azolowym, z lekami poprzedniej generacji. Zaobserwowano znaczny spadek aktywności biologicznej voriconazolu (podobnie jak starszych leków, takich jak fluconazol czy ketoconazol) względem komórek wielolekoopornych, co stanowi przesłankę, że nowy lek jest substratem dla głównych pomp kształtujących zjawisko wielolekooporności...
-
Impact resistance of plain and twill fabric in GFRP measured by active thermography
PublikacjaThis paper discusses the impact resistance of glass-fibre reinforced polymer (GFRP) composites depending on the type of reinforcement – plain or twill weave. The values of impact energy were: 3J, 10J and 15J. Specimens featuring twill weave transferred higher force during the impact as compared with plain weave specimens. It was observed that an increase of impact energy was accompanied by an increase of the disproportion in...
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublikacjaPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...
-
Rolling resistance and tyre/road noise on rubberised asphalt pavement in Poland
PublikacjaThe paper presents results of tyre/road noise and rolling resistance measurements performed on stone mastics asphalt (SMA) that contains rubberised asphalt, developed and produced by a refinery in Poland. Bituminous binder was modified with polymer and addition of crumb rubber. The first observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger...
-
Thin-walled cross section shape influence on steel member resistance.
PublikacjaThis work describes why trending thin-walled technology is achieving popularity in steel construction sector. A purpose of this article is to present the influence of the cold-formed element cross-section shape on an axial compression and a bending moment resistance. The authors have considered four different shapes assuming constant section area and thickness. Calculations were based on three different steel grades taking into...
-
Effects of the preheating laser treatment on microstructure and corrosion resistance of Ti6Al4V bioalloy
PublikacjaThe laser remelting of the Ti6Al4V alloy was made on specimens pre-heated at elevated temperatures. The laser treatment effected in change of microstructures of surface layers and an appearance of blisters and numerous cracks. The corrosion tests demonstrated the decrease in corrosion resistance for each preheating temperature. The observed effects were attributed to negative influence of excessive compressive stresses with no...
-
Effect of annealing temperature on slurry erosion resistance of ferritic X10CrAlSi18 steel
PublikacjaIn the present work, the slurry erosion tests were carried out to investigate the influence of heat treatment on slurry erosion process of ferritic X10CrAlSi18 stainless steel using a slurry pot test rig. X10CrAlSi18 stainless steel was tested in as-received condition and after annealing at three different temperatures: 600°C, 800°C and 1000°C. Degradation of materials due to slurry erosion depends on many factors connected with...
-
Influence of the femoral offset on the muscles passive resistance in total hip arthroplasty
PublikacjaBackground Soft tissue tension is treated as a crucial factor influencing the post-THA dislocation. The femoral offset is regarded as one of the major parameters responsible for the stabilization of the prosthesis. It is unclear which soft tissue is mostly affected by the offset changes. Methods A finite element model of the hip was created. The model comprised muscles, bones, a stem, the acetabular component and a liner. The muscles...
-
Oxide layers fabricated by spray pyrolysis for resistance random access memory
PublikacjaW pracy zbadano przydatność pirolizy aerozolowej do wytwarzania warstw dla memrystorów.
-
Transport deficiency is the molecular basis of Candida albicans resistance to antifungal oligopeptides
Publikacja(FMDP), an inhibitor of glucosamine-6-phosphate synthase, exhibited growth inhibitory activity against Candida albicans, with minimal inhibitory concentration values in the 0.05–50 mg/L range. Uptake by the peptide permeases was found to be the main factor limiting an anticandidal activity of these compounds. Di- and tripeptide containing FMDP (F2 and F3) were transported by Ptr2p/Ptr22p peptide transporters (PTR) and FMDP-containing...
-
Assessment of crack resistance of ship steels according to SEP 1390 standard
PublikacjaThe aim of the study was to evaluate the weldability of E36 nd NVE-36 steels by bending test according to SEP 1390. In the case of the specimen from E36 steel 9 external cracks were found, 5 of which were stopped in the fusion line and 4 in heat affected zone. In the case of the specimen from NVE-36 steel 8 external cracks were found, 4 of which were stopped in the fusion line and 4 in heat affected zone. Results of bending test...
-
Improved jamming resistance using electronically steerable parasitic antenna radiator
PublikacjaThis paper presents an idea of using an Electronically Steerable Parasitic Antenna Radiator (ESPAR) for jamming suppression in IEEE 802.11b networks. Jamming (intentional interference) attacks are known to be effective and easy to perform, which may impose connectivity problems in applications concerning Internet of Things (IoT). In our paper, theoretical considerations are presented and the results of experiments performed in...
-
SAMPLE-AND-HOLDING METHOD FOR GAS SENSING APPLIED FOR RESISTANCE GAS SENSORS
PublikacjaThe DC resistance of a Taguchi gas sensor is influenced by the ambient gas. To improve the selectivity and sensitivity of a sensor the fluctuation enhanced sensing (FES) was used. The paper proposes a novel methodology of utilizing FES technique that sample composition of an ambient atmosphere and hold it for further processing (sample-and-holding technique). The method uses the heated gas sensor to sample an ambient atmosphere...
-
The influence of the welding thermal cycles on corrosion resistance of duplex stainless steel
PublikacjaBadano skłonnośc strefy wpływu ciepła spoin ze stali dupleks do korozyjnego pękania narężeniowego. Wykonano próby korozyjne z wykorzystaniem metody SSRT w środowisku korozyjnym wrzącego MgCl2. Wykazano, że duży udział ferrytu w strukturze SWC pogarsza odpornośc na korozję. Badania metalograficzne na mikroskopie lektronowym wykazały różne sposoby propagacji pęknięcia zależnie od zawartości austenitu w strukturze SWC.
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublikacjaThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
Some Aspects of Shear Behavior of Soft Soil–Concrete Interfaces and Its Consequences in Pile Shaft Friction Modeling
PublikacjaThis paper examines the stiffness degradation and interface failure load on soft soil–concrete interface. The friction behavior and its variability is investigated. The direct shear tests under constant normal load were used to establish parameters to hyperbolic interface model which provided a good approximation of the data from instrumented piles. Four instrumented piles were used to obtain reference soil–concrete interface behavior....
-
Induction Assisted Hybrid Friction Stir Welding of Dissimilar Materials AA5052 Aluminium Alloy and X12Cr13 Stainless Steel
PublikacjaThis research aimed to study the induction in-situ heated hybrid friction stir welding (IAFSW) method to join AA5052 aluminium alloy with X12Cr13 stainless steel (SS) to enhance joint strength. The potency of this method on the mechanical properties and microstructural characterizations were also investigated. The results show that the transverse tensile strength gained was 94% of the AA5052 base metal that is 229.5 MPa. This superior...
-
Tribo-Environment Dependent Chemical Modification of Sliding Interfaces in Ultrananocrystalline Diamond Nanowall Film: A Correlation with Friction and Wear
PublikacjaTribological properties of ultrananocrystalline diamond nanowall (UNCD NW) films were investigated quantitatively in three different and controlled tribo-environmental conditions, proposing the passivation and graphitization mechanisms. However, these mechanisms are rather complicated and possibly can be understood in well-controlled tribological conditions. It was shown that the friction and wear of these films were high in highPage 1...
-
Improved model of isothermal and incompressible fluid flow in pipelines versus the Darcy–Weisbach equation and the issue of friction factor
PublikacjaIn this article, we consider the modelling of stationary incompressible and isothermal one-dimensional fluid flow through a long pipeline. The approximation of the average pressure in the developed model by the arithmetic mean of inlet and outlet pressures leads to the known empirical Darcy–Weisbach equation. Most importantly, we also present another improved approach that is more accurate because the average pressure is estimated...