Filters
total: 869
filtered: 787
Search results for: gas turbine · combustion chamber · steam injection · marine power plant
-
Elementary analysis and energetic potential of the sludge from the Gdynia Dębogórze and Lębork wastewater treatment plants
PublicationThe paper aims to show the results of the elementary analysis of the sewage sludges from wastewater treatment plants in Gdynia Dębogórze and Lębork as well as measurements of the heat of combustion and the calculated calorific values according to regulation PN-93/Z-15008, taking into account water content and the composition of sewage sludge at different utilisation stages. The results presented in this paper are based on the analysis...
-
Determination of SCFAs in water using GC-FID. Selection of the separation system
PublicationIn the present study, an analytical procedure was developed for the determination of short-chain fatty acids (SCFAs) in landfill leachate and municipal wastewater employing injection of aqueous samples to gas chromatograph with flame ionization detector (GC-FID). Chromatographic conditions such as a separation system, injection volume, oven temperature program were investigated and selected. With two columns, one with a polar (polyethylene...
-
Experimental investigation of domestic gas boiler fitted with ORC module
PublicationIn the paper the prototype of innovative domestic cogenerative ORC system, consisting of a conventional gas boiler and a small size axial vapour microturbines (in-house designed for ORC and the commercially available for Rankine cycle (RC)), evaporator and condenser were scrutinised. In the course of study the fluid working temperatures, rates of heat, electricity generation and efficiency of the whole system were obtained. The...
-
Analysis of the possibilities of using of DME fuel in motor boat drive systems
PublicationThe characteristics of alternative fuel for diesel: dimethyl ether (DME) and an analysis of the potential to reduce emissions of toxic compounds by the engines when running on this fuel have been presented in this work. Basic types of design solutions of gas supply and control systems, possible for use in internal combustion engines with DME supply have been also presented. The paper presents a study of the legislation and an analysis...
-
Performance analysis of power swing blocking feature in ABB 670 series impedance relays
PublicationThis paper presents test results of a distance protection’s PSD power swing detection feature in ABB 670 series relays. A RED670 relay was tested, which is part of the hydroelectric set protection in Żarnowiec Pumped Storage Plant. The power swing blocking feature’s performance was analysed on the basis of the results of object tests made with an Omicron digital tester. Also presented are simulation results that illustrate the...
-
Role of distillation in determination of SCFAs in samples of different origin
PublicationShort-chain fatty acids (SCFAs) are very volatile compounds and choosing an appropriate isolation and enrichement technique is a key to their determination. Distillation is one of methods which can be applied. There are many types of distillation. The simplest ones are direct, steam and fractional distillation, but they are not used very often and have some drawbacks. However, many modifications of basic distillation have been...
-
Drivetrain of a Wind Turbine
PublicationIn a most commonly met design of a wind turbine the power is transmitted from the rotor to the generator through the system composed of the main shaft, friction connection, multiplying gearbox and a flexible coupling. The driving system comprises almost a complete set of the machine elements being described during machine design lectures and can serve as an interesting illustration...
-
UKŁAD PRZENIESIENIA NAPĘDU TURBINY WIATROWEJ
PublicationIn a most commonly met design of a wind turbine the power is transmitted from the rotor to the generator through the system composed of the main shaft, friction connection, multiplicating gearbox and a flexible coupling. The driving system comprises almost a complete set of the machine elements being described during machine design lectures and can serve as an interesting illustration of the lectures.
-
Possibilities of heat transfer augmentation in heat exchangers with minichannels for marine applications
PublicationIn the paper, new trends in development of microchannel heat exchangers are presented. The exchangers developed in this way can be applied in marine applications. Main attention was focused on heat exchangers design with reduced size of passages namely based on microchannels. In our opinion future development of high power heat exchangers will be based on networks micro heat exchangers.
-
Gas Detection Using Resistive Gas Sensors And Radial Basis Function Neural Networks
PublicationWe present a use of Radial Basis Function (RBF) neural networks and Fluctuation Enhanced Sensing (FES) method in gas detection system utilizing a prototype resistive WO3 gas sensing layer with gold nanoparticles. We investigated accuracy of gas detection for three different preprocessing methods: no preprocessing, Principal Component Analysis (PCA) and wavelet transformation. Low frequency noise voltage observed in resistive gas...
-
Winding function approach based design of novel five-phase brushless doubly fed induction generator
PublicationThe paper presents the concept of the new design of the five-phase brushless doubly fed induction generator. The generator is dedicated to the modern wind turbine. The innovative design approach uses a five-phase power supply from the stator control winding side of the generator with a stator three-phase classic power winding. The research results presented indicate that the electromagnetic coupling between the control and power...
-
Prowadzenie ruchu małego źródła kogeneracji gazowej według kryterium efektu ekonomicznego
PublicationCechą charakterystyczną źródeł gazowych jest ich duża elastyczność ruchowa, w porównaniu do większości źródeł konwencjonalnych i odnawialnych. Cecha ta może i powinna być wykorzystywana do poprawy wskaźników ekonomicznych obiektu. W tym celu należy przeanalizować możliwości jakie daje prowadzenie ruchu źródeł nie w standardzie pracy z wymuszeniem zapotrzebowania na ciepło, ale właśnie maksymalnie wykorzystując elastyczność ruchową...
-
Prowadzenie ruchu małej elektrociepłowni gazowej według kryterium efektu ekonomicznego
PublicationCechą charakterystyczną źródeł gazowych jest ich duża elastyczność ruchowa, w porównaniu do większości źródeł konwencjonalnych i odnawialnych. Cecha ta może i powinna być wykorzystywana do poprawy wskaźników ekonomicznych obiektu. W tym celu należy przeanalizować możliwości jakie daje prowadzenie ruchu źródeł nie w standardzie pracy z wymuszeniem zapotrzebowania na ciepło, ale właśnie maksymalnie wykorzystując elastyczność ruchową...
-
Water-Lubricated Journal Bearings Marine Applications, Design, and Operational Problems and Solutions
PublicationWater-Lubricated Journal Bearings: Marine Applications, Design, and Operational Problems and Solutions provides cutting-edge design solutions, common problems and methods for avoiding them, and material selection considerations for the use of water-lubricated journal bearings in marine environments. These bearings have many advantages, including the absence of the potential for oil contamination. They are also sensitive, and their...
-
Thermal efficiency investigations on the self-ignition test engine fed with marine low sulfur diesel fuels
PublicationWithin the article an issues of implementing the new kinds of marine diesel fuels into ships’ operation was described taking into ac-count restrictions on the permissible sulphur content introduced by the International Maritime Organization. This is a new situation for ship owners and fuel producers, which forces the necessity to carry out laboratory research tests on especially adapted engine stands. How to elaborate the method...
-
Efficiency of gas detection algorithms using fluctuation enhanced sensing
PublicationEfficiency of various gas detection algorithms by applying fluctuation enhanced sensing method was discussed. We have analyzed resistance noise observed in resistive WO3- nanowires gas sensing layers. Power spectral densities of the recorded noise were used as the input data vectors for two algorithms: the principal component analysis (PCA) and the support vector machine (SVM). The data were used to determine gas concentration...
-
Analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers
PublicationThis paper presents an analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers. Using results of own operational research on dredgers this author determined thermal power demand for six hypothetical trailing suction hopper dredgers of various size, at accounting for a type of power system and kind of fuel combusted by dredger's power plant. By means of basic indices of...
-
Monitoring of Caged Bluefin Tuna Reactions to Ship and Offshore Wind Farm Operational Noises
PublicationUnderwater noise has been identified as a relevant pollution affecting marine ecosystems in different ways. Despite the numerous studies performed over the last few decades regarding the adverse effect of underwater noise on marine life, a lack of knowledge and methodological procedures still exists, and results are often tentative or qualitative. A monitoring methodology for the behavioral response of bluefin tuna (Thunnus thynnus)...
-
Experimental Investigation of the Performance of an Innovative Implantable Left Ventricular Assist Device—Proof of Concept
PublicationThis paper presents the results of experimental performance of an innovative left ventricular assist device working on a specially designed test stand. The introduced invention is mainly applied for supporting the heart in patients with end-stage heart failure accompanied by mitral valve regurgitation and pulmonary hypertension. Moreover, the developed device has the form of a flexible balloon forming an intracardiac inert gas-filled...
-
Fuel systems of high power stationary engine
PublicationThe use of alternative fuels and, in the future, synthetic fuels has forced changes in the design of fuel supply systems in internal combustion engines. When operating a stationary engine at constant load, the possibility of using lean fuel mixtures appears. The selection of a precise operating mixture ignition system requires changes in traditional fuel systems. The article presents the current designs of fuel supply systems and...
-
On the internal efficiency of a turbine stage: classical and CFD definitions
PublicationAlmost entire fleet of steam turbines in Poland was designed between 1950 – 1980 with the use of the so-called zero dimensional (0D) calculation tools. For several years, design and modernization of the turbines occur in assistance with the state of the art methods that describe working fluid flow field based on 3D models and CFD codes. This cooperation between 0D and 3D codes requires exchange of overall, integral information...
-
EMISJA AKUSTYCZNA JAKO SYGNAŁ DIAGNOSTYCZNY ODWZOROWUJĄCY ZMĘCZENIOWE ZUŻYCIE WARSTW ŚLIZGOWYCH PANWI ŁOŻYSK GŁÓWNYCH I KORBOWYCH SILNIKÓW O ZAPŁONIE SAMOCZYNNYM
PublicationW artykule przedstawiono wyniki badań laboratoryjnych, z których wynika, że emisja akustyczna (EA) może być uznana za sygnał diagnostyczny, przydatny do identyfikacji stanu technicznego łożysk głównych i korbowych okrętowych silników o zapłonie samoczynnym. Wykazano w nim bowiem, że parametry emisji akustycznej takie jak: czas rejestracji, energia sygnału, amplituda sygnału, ilość przekroczeń poziomu dyskryminacji, czas narastania,...
-
ASSESSMENT OF ENGINE OPERATION WITH THE USE OF AN OPERATION INDICATOR BASED ON TEST BENCH RESULTS OF A ROBINSUBARU EX17 ENGINE
PublicationPaper presents results of an experimental verification of the method of quantitative evaluation of engine operation, presented in the literature, exemplified by a low-power internal combustion piston engine. In accordance with such interpretation, engine operation may be presented as a physical quantity defined as operation indicator. The paper presents results of preliminary tests, processed in that aspect, carried out on an engine...
-
Computational complexity and length of recorded data for fluctuation enhanced sensing method in resistive gas sensors
PublicationThis paper considers complexity and accuracy of data processing for gas detection using resistance fluctuation data observed in resistance gas sensors. A few selected methods were considered (Principal Component Analysis – PCA, Support Vector Machine – SVM). Functions like power spectral density or histogram were used to create input data vector for these algorithms from the observed resistance fluctuations. The presented considerations...
-
Effectiveness of the robust PSS design
PublicationThe paper discusses optimal PSS of synchronous generator synthesis. The optimal controller is an Hinf controller, what means that minimises Hinf norm of transfer function between the exogenous signals such as reference inputs and disturbances, and the error signals which are to be minimised to meet the control objective. The dynamic properties of the plant are shaped by choosing appropriate weighting function applied to the plant...
-
Fault detection in the marine engine using a support vector data description method
PublicationFast detection and correct diagnosis of any engine condition changes are essential elements of safety andenvironmental protection. Many diagnostic algorithms significantly improve the detection of malfunctions.Studies on diagnostic methods are rarely reported and even less implemented in the marine engine industry.To fill this gap, this paper presents the Support Vector Data Description (SVDD) method as applied to thefault detection...
-
Medium-Voltage Drives: Challenges and existing technology
PublicationThe article presents an overview of state-of-art solutions, advances, and design and research trends in medium-voltage (MV) drive technologies - and also discusses the challenges and requirements associated with the use of such drives. The choice and deployment of MV drives in industries are associated with numerous requirements related to the front-end converter (grid side) and inverter (machine side). The focus is on solutions...
-
TEST METHOD FOR DETERMINING THE CHEMICAL EMISSIONS OF A MARINE DIESEL ENGINE EXHAUST IN OPERATION
PublicationThe article briefly describes the problem of air pollution caused by sea-going ships and the resulting restrictions on the emission of toxic and harmful chemical compounds in the exhaust of marine engines, introduced by the International Maritime Organization (IMO) under the International Convention for the Prevention of Sea Pollution from Ships (MARPOL 73/78). Such emissions provide a significant metrological problem, not only...
-
Low speed permanent magnet synchronous generator for vertical axis wind turbine
PublicationThe paper presents design process and tests of a prototype low speed permanent magnet synchronous generator (PMSG) dedicated for the innovative vertical-axis wind turbine. The rated data of the designed generator are following: power - 15 kVA, voltage - 400 V (Y), rotation speed - 93.75 rpm. The design assumptions, chosen results of the design process and experimental tests of the prototype PMSG are presented. The considered PMSG...
-
APPLICATION OF THE KOSECKI’S METHOD IN DESIGNING OF OFFSHORE WIND POWER PLANTS FOUNDATION
PublicationThe concept of offshore wind power plants has been well developed in many European countries. There is no such thing as design of offshore wind power plants according to national tradition. The main problem is the lack of standards and guidelines. Ones being applied are Scandinavian or American methods which are not fully adapted to the conditions of the Baltic Sea. The article focuses on the monopile design, as it is currently the...
-
Particulate Matter Production of Small Heat Source Depending on the Bark Content in Wood Pellets
PublicationWood pellets as biofuel are more and more used in small heat sources in Europe. Standard wood pellets are produced from wood sawdust without bark. The paper deals about the impact of bark in wood pellets on their properties and combustion process. Special attention in this work is paid to production of particulate matter during combustion of wood pellets depending on bark content. There were experimentally produced spruce wood...
-
Boron-Doped Diamond/GaN Heterojunction—The Influence of the Low-Temperature Deposition
PublicationWe report a method of growing a boron-doped diamond film by plasma-assisted chemical vapour deposition utilizing a pre-treatment of GaN substrate to give a high density of nucleation. CVD diamond was deposited on GaN substrate grown epitaxially via the molecular-beam epitaxy process. To obtain a continuous diamond film with the presence of well-developed grains, the GaN substrates are exposed to hydrogen plasma prior to deposition....
-
Experimental investigation of domestic micro-CHP based on the gas boiler fitted with ORC module
PublicationThe results of investigations conducted on the prototype of vapour driven micro-CHP unit integrated with a gas boiler are presented. The system enables cogeneration of heat and electric energy to cover the energy demand of household. The idea of such system is to produce electricity for own demand or for selling it to the electric grid – in such situation the system user will became the prosumer. A typical commercial gas boiler,...
-
Induction Generator with Direct Control and a Limited Number of Measurements on the Side of the Converter Connected to the Power Grid
PublicationThe article presents an induction generator connected to the power grid using the AC/DC/AC converter and LCL coupling filter. Three-level inverters were used in the converter, both from the generator side and the power grid side. The algorithm realizing Pulse Width Modulation (PWM) in inverters has been simplified to the maximum. Control of the induction generator was based on the Direct Field-Oriented Control (DFOC) method. At...
-
ENERGY AND EMISSION QUALITY RANKING OF NEWLY PRODUCED LOW-SULPHUR MARINE FUEL
PublicationThe article describes the methodology of engine tests on new types of low-sulphur marine fuels in laboratory conditions in order to conduct a comprehensive assessment of their suitability for powering full-size marine engines. The innovativeness of the proposed solution consists of adapting the laboratory Diesel Engine Test Bed to carry out experimental tests using residual and alternative fuels so that it is possible to imitate...
-
Analysis of catalitic reactors usefulness to reduce pollution generated by piston combustion engines with regard to ship main engines
PublicationThe article presents results which indicate that the use of catalytic reactors to reduce emissions of harmful compunds contained in the exhaust gas is important in the operation of vehicle motors operation. Efforts of the shipbuilding industry to reduce the toxicity of exhaust gas emitted by the main engines have been indicated and pointed to the desirability of the use of these catalysts in maritime transport. It has been pointed...
-
Pressure losses and power balance in the unloaded satellite pump
PublicationThis paper presents the results of laboratory research the pressure drop in the internal channels of unloaded satellite pump pumping tap water. Also shows the characteristics of the increase of pressure in the working chamber of the pump. It has been shown that after reaching cavitation, increase pump speed will increase in torque. This is the moment of inertia caused by the increase of the operating mechanism and the liquid contained...
-
PRESSURE LOSSES AND POWER BALANCE IN THE UNLOADED SATELLITE PUMP
PublicationThis paper presents the results of laboratory research the pressure drop in the internal channels of unloaded satellite pump pumping tap water. Also shows the characteristics of the increase of pressure in the working chamber of the pump. It has been shown that after reaching cavitation, increase pump speed will increase in torque. This is the moment of inertia caused by the increase of the operating mechanism and the liquid contained...
-
Sewage sludge co-pyrolysis with agricultural/forest residues: A comparative life-cycle assessment
PublicationThis study aims to determine the sustainability and energy efficiency of co-pyrolysis scenarios as treatment processes for municipal sewage sludge through a life cycle assessment (LCA). In addition, sensitivity and energy recovery analyses are conducted to determine the possible methods for optimizing the co-pyrolysis process from a circular bioeconomy perspective. Corncob and wood residue have been selected as potential co-feed...
-
Cellulose Nanofibers Isolated from the Cuscuta Reflexa Plant as a Green Reinforcement of Natural Rubber
PublicationIn the present work, we used the steam explosion method for the isolation of cellulose nanofiber (CNF) from Cuscuta reflexa, a parasitic plant commonly seen in Kerala and we evaluated its reinforcing efficiency in natural rubber (NR). Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and Thermogravimetric analysis (TGA) techniques...
-
The difficulties in polybrominated diphenyl ethers identification by GC-EI-MS technique
PublicationAwareness about the harmful effects of brominated flame retardants on living organisms increases mainly due to link their presence in the human environment with health disorders. Therefore is a need to conduct research aimed at content control of these chemicals in the environment. Recent improvements in injection techniques and mass spectrometer ionization methods have led to a variety of options to determine PBDEs in environmental...
-
Spectroscopic study of atmospheric pressure 915 MHz microwave plasma at high argon flow rate
PublicationIn this paper results of optical emission spectroscopic (OES) study of atmospheric pressure microwave 915 MHz argon plasma are presented. The plasma was generated in microwave plasma source (MPS) cavity- resonant type. The aim of research was determination of electron excitation temperature Texc gas temperature Tg and electron number density ne. All experimental tests were performed with a gas flow rate of 100 and 200 l/min and...
-
Two-phase optimizing approach to design assessments of long distance heat transportation for CHP systems
PublicationCogeneration or Combined Heat and Power (CHP) for power plants is a method of putting to use waste heat which would be otherwise released to the environment. This allows the increase in thermodynamic efficiency of the plant and can be a source of environmental friendly heat for District Heating (DH). In the paper CHP for Nuclear Power Plant (NPP) is analyzed with the focus on heat transportation. A method for effectivity and feasibility...
-
Efficient RSS-Based DoA Estimation for ESPAR Antennas Using Multiplane SDR Calibration Approach
PublicationIn this paper, we have introduced a new method to improve overall efficiency of direction-of-arrival (DoA) estimation scheme relying on received signal strength (RSS) values measured at the output port of electronically steerable parasitic array radiator (ESPAR) antenna. The proposed approach uses software-defined radio (SDR) setup and power pattern cross-correlation (PPCC) estimator involving multiple calibration planes. By placing...
-
O strumieniu mocy w silniku lub w układzie napędowym
PublicationW silniku lub w układzie napędowym wielkość strumienia mocy rośnie w kierunku przeciwnym do kierunku przepływu mocy. Straty energetyczne i sprawność energetyczna silnika lub układu napędowego powinny być przedstawiane jako funkcje wielkości fizycznych niezależnych od strat. Takimi wielkościami są prędkość i obciążenie silnika. Jednakże obraz strumienia mocy w silniku lub w układzie napędowym jest przedstawiany w literaturze w formie...
-
Application Isssues of the Semi-Markov Reliability Model
PublicationPredicting the reliability of marine internal combustion engines, for instance, is of particular importance, as it makes it possible to predict their future reliability states based on the information on the past states. Correct reliability prediction is a complex process which consists in processing empirical results obtained from operating practice, complemented by analytical considerations. The process of technical state changes...
-
Effect of the Presence of the Lifting Pocket on The THD Performance of a Large Tilting-Pad Thrust Bearing
PublicationIn this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of Itaipu power plant. B3earing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket
-
Flicker Noise in Resistive Gas Sensors—Measurement Setups and Applications for Enhanced Gas Sensing
PublicationWe discuss the implementation challenges of gas sensing systems based on low-frequency noise measurements on chemoresistive sensors. Resistance fluctuations in various gas sensing materials, in a frequency range typically up to a few kHz, can enhance gas sensing by considering its intensity and the slope of power spectral density. The issues of low-frequency noise measurements in resistive gas sensors, specifically in two-dimensional...
-
Stirling engines powered by renewable energy sources
PublicationStirling engine is a device that produces mechanical energy using heat from any source of energy, without the need of combustion of any fuel inside the device. Renewable energy sources, which are mostly low-temperature energy sources, can be used to produce mechanical and electrical energy in Stirling engines. The paper presents an overview of the existing prototype Stirling engines designed for using of low-temperature energy...
-
Reduction of Derivative pipeline effort in water turbine
PublicationThe paper presents an approach to evaluate and reduce the effort of the derivative pipeline in a water turbine of a hydrostatic power station in its vulnerable spots. Potential places of the biggest effort of the structure, as well as the coefficient of displacement and safety factor related to them were identified using FEM numerical method. Pipeline reinforcement was designed and made based on FEM analysis. Original technology...