Search
Filters
total: 944
filtered: 872
Search results for: waste tire rubber
-
To what extent can hyperelastic models make sense the effect of clay surface treatment on the mechanical properties of elastomeric nanocomposites?
PublicationThe poor knowledge about nonlinear mechanical behavior of elastomer nanocomposites arises from the incomplete information on the interface. Application of hyperelastic models provides more insights into the nature and the situation of interaction between the elastomeric matrix and nanofillers. The current work seeks to address the effect of interphase strength on tensile properties of the elastomer nanocomposites under large deformations....
-
Extremophile Deinococcus geothermalis as potential source of proteolytic enzymes
PublicationAmong many extremozymes, thermophilic enzymes have attracted most attention during the past four decades. Such enzymes are of considerable industrial and biotechnological interest due to the fact that the enzymes are better suited for harsh industrial processes. There are many advantages of conducting industrial processes at high temperature, such as the increased solubility of many polymeric substrates, resulting in decreased...
-
WSPÓŁPRACA BLOKU GAZOWO-PAROWEGO Z OBIEGIEM ORC = Combinded power plant in cooperation with ORC
PublicationIn the paper presented is the idea of a combined gas and steam power plant cooperation with a low temperature organic Rankine cycle ORC unit. Considerations presented in the paper are accomplished for the Gorzów CHP. The intention of present analysis is heat recovery of low temperature energy and its further use in ORC cycle in order to produce electricity, without increase in fuel consumption. Waste energy is recovered from the...
-
Rapeseed oil methyl ester production in an individual household
PublicationFatty acid methyl esters, commonly known as biodiesel, are a cheap and environmental-friendly fuel substitute for diesel engines. Aside from industrial production, individual biodiesel manufacturing is also and important method of fulfilling the requirements of EU Parliament directive no. 2003/30/WE about supporting the use of renewable fuels in transport. Individual FAME production guarantees easy access to the main raw material...
-
Theoretical Organic Rankine Cycle efficiency depending on different thermodynamic work variables.
PublicationOne of promising technologies of utilizing low- temperature waste heat is through ORC (Organic Rankine Cycle) system implementation. A primary objective in designing in-stallations based on such systems is to maximize the installation's work efficiency. On the other hand, ecological factors are commonly considered a natural barrier in introducing new, often very expensive technologies. Ecological effect of a potential modernization...
-
Assessing the industrialization progress of hydrodynamic cavitation process intensification technology: a review
PublicationHydrodynamic cavitation (HC) is widely acknowledged as a promising green approach for enhancing various production and waste management processes, such as water treatment, sludge pretreatment, lignocellulosic biomass (LCB) pretreatment, emulsification, and food processing. Despite demonstrating superior industrialization potential compared with other emerging technologies such as ultrasound and microwave, the widespread commercial...
-
Porous carbon derived from rice husks as sustainable bioresources: insights into the role of micro-/mesoporous hierarchy in hosting active species for lithium–sulphur batteries
PublicationThe exploration of natural resources as sustainable precursors affords a family of green materials. Exploring highly abundant and available biowaste precursors remaining from food processing throughout a scalable and cost-effective material synthesis path is highly important especially for new materials discovery in emerging energy storage technologies such as lithium–sulphur (Li–S) batteries. Herein, we have produced a series...
-
Static Model of Steam/Water Cycle for Thermal and Economic Analysis
PublicationThe thermodynamic efficiency of typical conventional and nuclear power plants is insufficient. A large amount of the generated heat is removed to the environment and regarded as a waste. A solution which is commonly used to increase the efficiency and profitability of the existing and planned power plants refers to cogeneration of heat and power. To prepare sophisticated thermodynamic and economic analyses, a precise static model...
-
Experimental study of pressure rise at the evaporator of capillary pumped loop with acetone and water as working fluids
PublicationIn this work studied is the possibility of fluid pumping using capillary forces in the capillary pumped loop. Experimental and theoretical studies have been performed to understand the phenomena associated with heat transfer in porous structure of the evaporator. The capillary effect was studied during operation of two different capillary porous structures with two different working fluids, namely water and acetone. The results...
-
Current Status, Barriers and Development Perspectives for Circular Bioeconomy in Polish South Baltic Area
PublicationThe following article presents the current legal situation in Poland as well as in the European Union. Data on biomass production in the Polish South Baltic area were analyzed, along with an indication of the key sectors for the development of bioeconomy. Presentation of the current state of biomass management was made and areas necessary for development were indicated to facilitate the sustainable management of biomass and waste...
-
The performance of H2O, R134a, SES36, ethanol, and HFE7100 two-phase closed thermosyphons for varying operating parameters and geometry
PublicationIn this study, the influences of different parameters at performance two-phase closed thermosiphon (TPCT) was presented. It has been confirmed that the working fluid, as well as operating parameters and fill ratio, are very important factors in the performance of TPCT. The article shows characteristics of gravitational tube geometr ies, as well as the technical characteristic of the most important system components, i.e., the evaporator/condenser....
-
Susceptibility to Degradation in Soil of Branched Polyesterurethane Blends with Polylactide and Starch
PublicationA very important method of reducing the amount of polymer waste in the environment is the introduction to the market of polymers susceptible to degradation under the influence of environmental factors. This paper presents the results of testing the susceptibility to degradation in soil of branched polyesterurethane (PUR) based on poly([R,S]-3-hydroxybutyrate) (R,S-PHB), modified with poly([D,L]-lactide) (PLA) and starch (St). Weight...
-
Evaluation of the efficiency of the duty cycle of refuse collection vehicle based on real-world data
PublicationIn this paper a method of the efficiency evaluation of the duty cycle of Refuse Collection Vehicle is presented. Using real world data, two representative duty cycles were analysed. Total cycle efficiency was calculated, as well as the efficiency of particular cycle phases. Then, energy needed to collect and compact the waste and energy from fuel were compared. Measured and calculated values were shown on the diagrams illustrating...
-
Natural/bio-based sorbents as greener extractive materials for endocrine disrupting compounds in samples of different matrix composition
PublicationEndocrine-disrupting compounds (EDCs) are a group of chemicals that interfere with the endocrine system, leading to adverse effects on human health and the environment. Increasing concerns over the EDCs presence in various environmental compartments has driven the search for greener extraction materials. Recently, the use of polymers of natural origin (biopolymers) has been demonstrated to be an effective and promising research...
-
Remediation of soils on municipal rendering plant territories using Miscanthus × giganteus
PublicationPhytoremediation, as a cost-effective, highly efficient, environmentally friendly, and green approach, gained attention to the removal of metals, including heavy metals, from contaminated soils. The toxic nature of heavy metals can have an adverse effect on human health and the ecosystem, and their removal remains a worldwide problem. Therefore, in this study, a field experiment was carried out to evaluate the potential of Miscanthus × giganteus...
-
Smartphone-Assisted and Optical Quantification of Copper and Glucose Using Palm Wine-Tailored Carbon Dots and Their Multiple Logic Gate Application
PublicationIn this work, potassium, sulfur, nitrogen, and chlorine self-doped carbon dots (CDs) were hydrothermally synthesized using palm wine as a carbon source. The palm wine-derived CDs (PW-CDs) are amorphous in nature and displayed an average particle size of 4.19 ± 0.89 nm. The as-synthesized CDs are used to fabricate a photoluminescent sensing probe to simultaneously detect Cu2+ and glucose via the “Turn ON−OFF−ON” mechanism. The PL...
-
Design and numerical testing of 5-box gfrp shell footbridge
PublicationThe paper formulates new design conditions for composite footbridges, taking into account the material and structural specificity of these objects, i.e. the strength condition, the serviceability condition and the frequency condition. A GFRP composite footbridge labelled with CFB2 code has been designed, with the original superstructure in the form of an opened-closed 5-box girder. The foot and cycle track bridge is simply supported,...
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublicationA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
Reactive extrusion of bio-based polymer blends and composites – Current trends and future developments
PublicationReactive extrusion is a cost-effective and environmentally-friendly method to produce new materials with enhanced performance properties. At present, reactive extrusion allows in-situ polymerization, modification/functionalization of polymers or chemical bonding of two (or more) immiscible phases, which can be carried out on commonly used extrusion lines. Although reactive extrusion has been known for many years, its application...
-
Poroelastic Road Surface – a Promising Road Traffic Noise Abatement Solution
PublicationRoad surfaces have a direct impact on the generation of noise by rolling tyres, the main and dominant source of noise of moving vehicles, as well as may affect propagation of noise emitted by all noise sources of a vehicle. Thus there is no doubt that pavement should be considered as one of the major potential road traffic noise abatement measure. Low noise pavements of existing types may in new conditions provide up to 8 dB of...
-
Further development of the poroelastic road surface within the new Polish project SEPOR
PublicationRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
Laboratory assessment of permeability of sand and biopolymer mixtures
PublicationLaboratory assessment of permeability of sand and biopolymer mixtures. This research presents a method of creating seepage barriers in a sandy soil using biopolymer additives (biosubstance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The paper aims to investigate the infl uence of a biosubstance employed in a highly permeable sandy soil. Amount of the...
-
Distillation cleanup preceded gc determination of short-chain monocarboxylic acids in aqueous and solid samples of wastewater origin = Oznaczanie krótkołańcuchowych kwasów monokarboksylowych w próbkach wodnych i stałych pochodzących z oczyszczalni ścieków z wykorzystaniem chromatografii gazowej poprzedzonej destylacją
PublicationShort-chain monocarboxylic acids (SCMAs) (C2-C5) formed in the process of aerobic biodegradation of larger organic molecules should often be monitored to optimize wastewater biological treatment and study the processes of converting organic waste matter into methane, etc. Gas chromatography (GC) seems a method of choice for such a task. Majority of samples require clean up before they can be injected into GC system. In this work...
-
Knowledge risks - towards a taxonomy
PublicationThe paper aims to identify, describe and analyse knowledge risks organisations might face and based on this, proposes a taxonomy of knowledge risks. To achieve this goal, a literature review was conducted. After the analysis of the existing material, it was possible to divide knowledge risks into two categories: internal (originating from the inside of the organisation) and external (originating from the outside of the organisation)....
-
Application of lightweight cement composite with foamed glass aggregate in shell structures
PublicationThe purpose of the paper is to investigate the abilities of applying Granulated Expanded Glass Aggregate (GEGA) as a natural volume substitute of aggregate as a component of lightweight concrete. The GEGA aggregates used in the experiments were made of confused glass waste. In order to achieve satisfactory strength of concrete Granulated Ash Aggregate (GAA) was added as well. To produce specimens three grain sizes of aggregates...
-
Stirling engines - the state of technology development and computational models
PublicationStirling engines represent a technologically important solution in combined heat and power systems. Their use enables the achievement of over 90 percent efficiency in the management of the primary energy source with a very high durability of the device, mainly due to the lack of contact of the working gas with external factors and a very small number of mechanical components. The use of a Stirling engine may be equally important...
-
Pyrolysis of RDF and Catalytic Decomposition of the Produced Tar in a Char Bed Secondary Reactor as an Efficient Source of Syngas
PublicationOne of the technical limitations of refuse-derived fuel (RDF) pyrolysis is the high content of tar in its gas products. In order to resolve this problem, a two-stage RDF pyrolysis with a catalyst based on char from RDF pyrolysis is proposed. This paper presents the results of municipal waste pyrolysis beginning in an oven heated to 480 °C and ending with catalytic tar cracking carried out in the temperature range from 800 to 1000...
-
Katalizatory wykorzystywane w syntezie biodiesla
PublicationRising prices of electricity, conventional fuels and heating require decisive steps in the further development of technologies based on renewable energy sources. These include geothermal-; hydrothermal-; aerothermal-; and solar energy. Due to the fact that the petrochemical industry is one of the fastest growing branches of the economy, we would like to expand on the topic related to biofuels. Biodiesel is an alternative fuel similar...
-
AGREEprep – Analytical greenness metric for sample preparation
PublicationThis work proposes for the first time, a metric tool that gives prominence to sample preparation. The developed metric (termed AGREEprep) was based on 10 categories of impact that were recalculated to 0 e1 scale sub-scores, and then used to calculate the final assessment score. The criteria of assessment evaluated, among others, the choice and use of solvents, materials and reagents, waste generation, energy consumption, sample...
-
ICT-enabled circular economy: conceptualising the links
PublicationThis chapter sets conceptual backgrounds regarding the potentially emerging causal links between digital technologies and circular economy ideas implementation. We argue that digital technologies may constitute an effective element enabling the transformation from linear to circular and environmentally friendly economic activities. This work draws the general picture at the macro and micro level. The macro perspective shows how...
-
Emerging Processes for Sustainable Processing of Food Ingredients and Products
PublicationIn recent decades, traditional food processing processes, such as homogenization, pasteurization, canning, drying, and smoking, among others, have been successfully applied to obtain, to some extent, acceptable food items. However, with the increasing food demand, as a consequence of the growing population worldwide, new, tunable, and enriched food products are demanded, requiring the implementation of emerging technologies in...
-
PERS - QUIET ROAD SURFACE FOR URBAN AREAS
PublicationTraffic noise is one of the most important environmental problems in densely populated urban areas. At low speeds the tyre/road interaction dominates all other sources. It is anticipated that when electric and hybrid vehicles gain dominance in city traffic, the importance of tyre/road noise will still increase as electric engines are much less noisy than combustion engines. On the other hand, electric and hybrid urban vehicles...
-
Bitumen-Based Poroelastic Pavements: Successful Improvements and Remaining Issues
PublicationThis article presents the development process of designing and testing poroelastic pavement based on highly polymer-modified bitumen. Poroelastic wearing course was composed of mineral and rubber aggregate mixed with highly polymer-modified bitumen, in contrast to previous trials, during which polyurethane resins were mainly used as binder, which led to several serious technological problems concerning difficult production, insufficient...
-
Metrics for green analytical chemistry
PublicationGreen analytical chemistry, although not being a new concept, does not have a greenness metrics system. Green chemistry metrics are not suitable for analytical procedure assessment because they often refer to the mass of the product. Some efforts have been made to develop suitable metrics for analytical chemistry. Some are simple to use but do not cover all aspects of analytical methods’ environmental impact. Others are more comprehensive...
-
Recycling of raw materials, silicon wafers and complete solar cells from photovoltaic modules
PublicationPhotovoltaic modules (PVs) are an attractive way of generating electricity in reliable and maintenance-free systems with the use of solar energy. The average lifetime of photovoltaic modules is 25 to 30 years. To offset the negative impact of photovoltaic modules on the environment, it is necessary to introduce a long-term strategy that includes a complete lifecycle of all system components from the production phase through installation...
-
CHROMATOGRAPHIC TECHNIQUES IN PHARMACEUTICAL ANALYSIS IN POLAND: HISTORY AND THE PRESENCE ON THE BASIS OF PAPERS PUBLISHED IN SELECTED POLISH PHARMACEUTICAL JOURNALS IN XX CENTURY
PublicationFor a long time, chromatographic techniques and techniques related to them have stimulated the development of new procedures in the field of pharmaceutical analysis. The newly developed methods, characterized by improved metrological parameters, allow for more accurate testing of, among others, the composition of raw materials, intermediates and final products. The chromatographic techniques also enable studies on waste generated...
-
New insights of nanomaterials usage toward superhydrophobic membranes for water desalination via membrane distillation: A review
PublicationMembrane distillation (MD) is a promising technology for seawater desalination due to the ability to process high-salinity waters and the ability to be driven by low-grade or waste heat. However, practical applications of MD membranes are limited by the low vapor flux and fouling problem. Recently, there is a growing interest in developing novel MD membrane materials with enhanced hydrophobicity to improve the efficiency of desalination...
-
One-step recovery of REE oxalates in electro-leaching of spent NdFeB magnets
PublicationRecovery of rare-earth elements (REEs) from spent NdFeB magnets is receiving great attention because of high amount of neodymium and potential risk of environmental pollution. In this study, a novel environment-friendly hydrometallurgical route is proposed for efficient recovery of REEs during electrochemical leaching with sulfuric and oxalic acids. With proper adjustment of the electrolyte composition and operating conditions,...
-
Assessment of wastewater quality indicators for wastewater treatment influent using an advanced logistic regression model
PublicationInfluent quality indicators play a significant role in wastewater treatment plant performance due to their correlation with reactor operations and effluent quality. However, selecting a specific/best parameter indicator for predicting influent wastewater quality is one of the challenges in wastewa- ter treatment. This study, therefore, focused on determining suitable variables as influent quality indicators. For this purpose, a...
-
Recycled Polyurethane as a Second Phase in Thermoset Blends and Its Effect on Thermal Degradation Kinetics Studies
PublicationA new approach is introduced in the modification of thermosetting polymer by using different amount of polyurethane of waste origin. The post consumer polyurethane foam coatings are degraded using glycolysis process and the recycled product is further converted into new polyurethane. The blending of recycled polyurethane with epoxy exhibits transparency and produces nanostructures. The effective interaction between two polymers...
-
Surfactants application in sample preparation techniques: Insights, trends, and perspectives
PublicationSince the implementation of Green Chemistry into analytical practice, significant efforts have been made to improve the sustainability of chemical analysis. These include reducing the use of hazardous chemicals and solvents, minimizing waste, and improving energy efficiency. Surfactants can be applied in chemical analysis as an environmentally friendly alternative to conventional solvents and chemicals. The use of surfactants can...
-
Medium-Voltage Drives: Challenges and existing technology
PublicationThe article presents an overview of state-of-art solutions, advances, and design and research trends in medium-voltage (MV) drive technologies - and also discusses the challenges and requirements associated with the use of such drives. The choice and deployment of MV drives in industries are associated with numerous requirements related to the front-end converter (grid side) and inverter (machine side). The focus is on solutions...
-
The innovative exploitation of Brassica vegetables in the health quality food production chain
PublicationIn this overview the multidirectional opportunities of innovative exploitation of chemical and biological properties of vegetables from Brassiceae family are discussed. The specific chemical composition of brassicas, as regard both nutrients and non-nutrients, renders them particularly suitable for the health food production chain, literally from field to fork. the ability of these plants to accumulate heavy metals may be utilised...
-
The innovative Exploitation of Brassica Vegetables in the Health Quality Food Production Chain
PublicationIn this overview the multidirectional opportunities of innovative exploitation of chemical and biological properties of vegetables from Brassiceae family are discussed. The specific chemical composition of brassicas, as regard both nutrients and non-nutrients, renders them particularly suitable for the health food production chain, literally from field to fork. the ability of these plants to accumulate heavy metals may be utilised...
-
METHODS OF LIQUID BIOFUEL PRODUCTION – THE BIOETHANOL EXAMPLE
PublicationEthanol is used in chemical and food industry, mainly either in the synthesis or as a solvent. The newest application of ethanol is as a fuel. This alcohol, produced on an industrial scale from crop waste, is widely known under the name bioethanol. It could be used as a fuel by itself or in a mixture with gasoline. Today, there are several technologies for bioethanol production known. The relatively simple method of obtaining bioethanol...
-
Rheological characteristics of oligomeric semiproducts gained via chemical degradation of polyurethane foam using crude glycerin in the presence of different catalysts
PublicationPolyurethane (PU) recycling is a topic of growing interest due to the increasing amount of polyurethane waste. The main purpose of polyurethane chemical recycling is to recover the starting polyol. In this study, a method of polyurethane thermochemical recycling, glycerolysis by means of crude glycerin, is proposed. This work presents a comparative study of commercial catalysts used in order to accelerate the decomposition process,...
-
Assessment of the water quality of Kłodnica River catchment using self-organizing maps
PublicationRisk assessment of industrial areas heavily polluted due to anthropogenic actions is of increasing concern worldwide. So is the case of Polish Silesia region where mostly heavy industry like smelters, mining, chemical industries as well as heat and electricity production facilities are being located. Such situation raises numerous questions about environmental state of local water bodies with special attention paid to the Kłodnica...
-
Methods of liquid biofuels production - the bioethanol example.
PublicationEthanol is used in chemical and food industry, mainly either in the synthesis or as a solvent. The newest application of ethanol is as a fuel. This alcohol, produced on an industrial scale from crop waste, is widely known under the name bioethanol. It could be used as a fuel by itself or in a mixture with gasoline. Today, there are several technologies for bioethanol production known. The relatively simple method of obtaining bioethanol...
-
Hydraulic conductivity of a biopolymer treated sand
PublicationThis paper presents results of laboratory assessment of creating seepage barriers in a sandy soil using biopolymer additives (bio substance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The aim of the conducted work was to investigate the influence of a biosubstance employed in a highly permeable sandy soil. The amount of the biopolymer used in a sample...
-
A Noded Carbon Emission Tool (NCET) to Measure Embodied Carbon (EC) in Compositional Cementitious Materials
PublicationThe ever evolving modern construction industry is now producing the highest levels of carbon content adversely affecting the construction associated environment. Although, the impact of carbon induced emission is quite large, but still not enough measurable standards and tools to scale these emission are available. This study contributes to the body of knowledge by providing a Grasshopper based definition to calculate the embodied...