Search
Filters
total: 2258
filtered: 1906
displaying 1000 best results Help
Search results for: ACCELERATED THERMAL AGING
-
rigid polyurethane foams modified with selected nanofillers
PublicationThe nanofillers: natural montmoryllonite (MMT) - Bentonite, natural MMT modified with a quaternary ammonium salt - Cloisite30B, has been used in rigid polyurethane foams (PUFs). The influence of fillers amounts on processing parameters, physical-mechanical properties (density, water absorption, brittleness and compression strength) and thermal properties (thermal stability, fire behaviours) of such foams has been analysed. The...
-
Effect of soil moisture on current-carrying capacity of low-voltage power cables
PublicationOne of the factors affecting current-carrying capacity of underground power cables is the thermal resistivity of soil. Its value in the close proximity of the cable is the most important, and for this reason, in some cases, the local soil is replaced with an another soil type or with a cement-sand mixture. The thermal resistivity of the soil is strongly affected by moisture, and in the case of a cement-sand mixture – as tested...
-
Effectiveness of various types of coating materials applied in reinforced concrete exposed to freeze–thaw cycles and chlorides
PublicationThis study assesses the durability of coated and uncoated concrete surfaces protected with four different coating materials: water-soluble (BW), solvent-based (BR), mineral (MI), and epoxy (EP). The durability assessment includes evaluating the absorption rate of water, pull-off adhesion strength, and coating material thickness. Concrete samples were subjected to immersion in regular water and a 7% urea solution, followed by...
-
Effectiveness of various types of coating materials applied in reinforced concrete exposed to freeze–thaw cycles and chlorides
PublicationThis study assesses the durability of coated and uncoated concrete surfaces protected with four Different coating materials: water-soluble (BW), solvent-based (BR), mineral (MI), and epoxy (EP). The durability assessment includes evaluating the absorption rate of water, pull-of adhesion strength, and coating material thickness. Concrete samples were subjected to immersion in regular water and a 7% urea solution, followed by cyclic...
-
Thermoplastic polyurethane/(organically modified montmorillonite) nanocomposites produced by in situ polymerization
PublicationA series of polyurethane nanocomposites were synthesized from thermoplastic polyurethanes (with different hard segment ratios) and two types of organically modified montmorillonites (OMMT) - Cloisite® 10A and Cloisite® 20A. The thermal behavior was examined by non-isothermal thermogravimetry (TG, DTG), Differential Scanning Calorimetry (DSC) and Dynamic-Mechanical Thermal Analysis (DMTA). The results of X-ray analyses showed that...
-
Problems of Active Dynamic Thermography Measurement Standardization in Medicine
PublicationReliability of thermographic diagnostics in medicine is an important practical problem. In the field of static thermography, a great deal of effort has been made to define the conditions for thermographic measurements, which is now the golden standard for such research. In recent years, there are more and more reports on dynamic tests with external stimulation, such as Active Dynamic Thermography, Thermographic Signal Reconstruction...
-
Structural properties of mixed conductor Ba1−xGd1−yLax+yCo2O6−δ
PublicationBa1−xGd1−yLax+yCo2O6−δ (BGLC) compositions with large compositional ranges of Ba, Gd, and La have been characterised with respect to phase compositions, structure, and thermal and chemical expansion. The results show a system with large compositional flexibility, enabling tuning of functional properties and thermal and chemical expansion. We show anisotropic chemical expansion and detailed refinements of emerging phases as La is...
-
Experimental ultimate strength assessment of stiffened plates subjected to marine immersed corrosion
PublicationThis study experimentally analyses the impact of marine immersed corrosion degradation on the compressive strength of the stiffened plates where the lower degradation levels were considered. The corrosion degradation test was accelerated by controlling the natural corrosion environmental factors, avoiding applying an electric current. Different groups of corrosion degradation levels and initial plate thicknesses were investigated....
-
Mechanism of the Reaction of Amines with 5-[(Aryl- or Alkylamino)hydroxymethylene]-2,2-dimethyl-1,3-dioxane-4,6-diones in the Presence of Chlorotrimethylsilane (Me3SiCl);
PublicationAddition of chlorotrimethylsilane (Me3SiCl) to the mixture of a carbamoyl‐substituted Meldrum's acid, i.e., a 5‐[(arylamino)hydroxymethylene]‐2,2‐dimethyl‐1,3‐dioxane‐4,6‐dione of type 1 and a secondary amine as nucleophile strongly accelerated the rate of their reaction. The reason for this phenomenon observed, during our previous research, remained, however, unclear. To elucidate the mechanism of this reaction, we assumed and...
-
Parallel implementation of the DGF-FDTD method on GPU Using the CUDA technology
PublicationThe discrete Green's function (DGF) formulation of the finite-difference time-domain method (FDTD) is accelerated on a graphics processing unit (GPU) by means of the Compute Unified Device Architecture (CUDA) technology. In the developed implementation of the DGF-FDTD method, a new analytic expression for dyadic DGF derived based on scalar DGF is employed in computations. The DGF-FDTD method on GPU returns solutions that are compatible...
-
Degradation of Gel-Coat Layer in Glass/Polyester Laminate in Seawater Environment
PublicationGlass/polyester laminate coated with gelcoat layer of different thickness 0,5; 1,5; 3 mm was studied in terms of blistering behaviour and water sorption in hot water environment. Blistering was found to be accelerated for thin (0,5 mm) gel-coat layer compared to the thick (1,5; 3 mm), however no significant difference in blistering behaviour was observed between the laminates with gel-coat thickness 1,5 and 3 mm which may suggest...
-
Wykluczenie finansowe starszych konsumentów na rynku usług finansowych
PublicationCelem opracowania jest identyfikacja uwarunkowań wykluczenia finansowego starszych konsumentów na rynku usług finansowych. Dla realizacji tego celu zidentyfikowano m.in. podstawowe pojęcia dotyczące wykluczenia (w tym wykluczenia finansowego) osób starszych. Zagrożenia wynikające z wykluczenia finansowego starszych konsumentów zostały zilustrowane poprzez analizę danych statystycznych dotyczących starzenia się społeczeństwa. Podstawowy...
-
THE INFLUENCE OF WSR PARAMETER ON PET BOTTLE THICKNESS PROFILE IN SBM FROM PREFORM PROCESS
PublicationFrom a mechanical point of view, the thickness profile of PET bottles manufactured by ISBM process is determined by mechanical and thermal response of blown preforms. From the microscopic point of view the biggest influence on the mechanical and thermal properties of PET bottles have orientation and crystallization processes. From a technological point of view, the thickness profile of PET bottles after manufacture by SBM process...
-
Accurate Computation of IGBT Junction Temperature in PLECS
PublicationIn the article, a new method to improve the accuracy of the insulated-gate bipolar transistor (IGBT) junction temperature computations in the piecewise linear electrical circuit simulation (PLECS) software is proposed and described in detail. This method allows computing the IGBT junction temperature using a nonlinear compact thermal model of this device in PLECS. In the method, a nonlinear compact thermal model of the IGBT is...
-
How non-technological innovation saved the day by using ICT
PublicationCertainly, the current pandemic situation provides a lot of evidence of the need for non-technological innovations, both in the area of company organization and marketing. Socio-cultural innovations are not less important. Therefore, the role of non-technological innovation during the COVID-19 pandemic is discussed in the sixth chapter. Innovations supported by digital solutions have become a silent heroes for many companies as...
-
Consistency of Quantum Computation and the Equivalence Principle.
PublicationThe equivalence principle, being one of the building blocks of general relativity, seems to be crucial for analysis of quantum effects in gravity. In this paper we consider the relation between the equivalence principle and the consistency of quantum information processing in gravitational field. We propose an analysis with a looped evolution consisting of steps both in the gravitational field and in the accelerated reference frame....
-
FPGA Acceleration of Matrix-Assembly Phase of RWG-Based MoM
PublicationIn this letter, the field-programmable-gate-array accelerated implementation of matrix-assembly phase of the method of moments (MoM) is presented. The solution is based on a discretization of the frequency-domain mixed potential integral equation using the Rao-Wilton-Glisson basis functions and their extension to wire-to-surface junctions. To take advantage of the given hardware resources (i.e., Xilinx Alveo U200 accelerator card),...
-
Automated Reduced Model Order Selection
PublicationThis letter proposes to automate generation of reduced-order models used for accelerated -parameter computation by applying a posteriori model error estimators. So far,a posteriori error estimators were used in Reduced Basis Method (RBM) and Proper Orthogonal Decomposition (POD) to select frequency points at which basis vectors are generated. This letter shows how a posteriori error estimators can be applied to automatically select...
-
WEAR OF Si OR B DOPED AMORPHOUS CARBON COATINGS
PublicationThe paper describes a complex wear research on DLC (amorphous carbon) moped with boron (B) and silicone (Si). The tests were carried out in two different sliping systems: flat–on–flat (ring contact, unidirectional sliding) and ball–on–flat (reciprocating sliding). Water and medical saline solutions were used as lubricants. A comparative analysis of the results revealed differences in the initiation and progress of wear and the...
-
Determination of pharmaceuticals in fish: method optimization and occurrence in different species from Mediterranean rivers
PublicationThe multi-residue analytical method developed, based on accelerated solvent extraction, gel permeation chromatography purification and UPLC-MS/MS analysis allowed the simultaneous determination of 21 pharmaceuticals. Recoveries obtained for most of the target compounds were higher than 50%. The application of UPLC-MS/MS operating in the MRM mode, with two transitions monitored for each compound, provided good sensitivity and selectivity....
-
Implementation of FDTD-Compatible Green's Function on Graphics Processing Unit
PublicationIn this letter, implementation of the finite-difference time domain (FDTD)-compatible Green's function on a graphics processing unit (GPU) is presented. Recently, closed-form expression for this discrete Green's function (DGF) was derived, which facilitates its applications in the FDTD simulations of radiation and scattering problems. Unfortunately, implementation of the new DGF formula in software requires a multiple precision...
-
Assessment of Tensile Strength Reserve of Asphalt Mixtures at Low Temperatures
PublicationDuring winter conditions, low-temperature cracks develop at the surface of the asphalt pavement when tensile thermal stress induced in the asphalt layer during cooling equals and exceeds the tensile strength of the material. The paper presents the results of tensile strength reserve assessment of asphalt mixtures with neat and SBS-polymer modified bitumen application. The tensile strength reservewas calculated as difference between...
-
Complementary Use of Multi-dimensional Gas Chromatography and Proton Transfer Reaction Mass Spectrometry for Identification of Rapeseed Oil Quality Indicators
PublicationThe change of concentration of various volatiles generated during frying may be an indicator of oil quality. Chemical compounds such as aldehydes, ketones, alcohols and carboxyl acids are the products of oxidation during thermal degradation of edible oils. Shown in this work is a complementary use of GC×GC-TOFMS and PTR-MS for the detection and determination of quality indicators of rapeseed oil. The former technique was used for...
-
TERMODYNAMIC CALCULATIONS OF TURBINE STEAM PARAMETERS
PublicationIn this work a heat balance was made for the nominal conditions of a block working with 18K370 turbine. For the parameters obtained, the thermal-flow calculations of the steam turbine were performed, maintaining the actual geometry of its flow system. Based on the nominal values obtained, iterative thermal and flow calculations were made for both the heat cycle of the power plant block and the steam turbine itself, seeking to obtain...
-
Application of gas chromatography to evaluate the quality of rapeseed oil
PublicationTwo-dimensional gas chromatography is an analytical technique, which is increasingly being used in food research. Through the analysis of volatile fraction, it is possible to determine the quality of food products. One of the reasons for the deterioration of food is thermal degradation. Products that are often subject to degradation reactions due to temperatures are edible oils. In the thesis, the results of edible oils with different...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART V) METHODS ENSURING CORRECT START-UP OF HYDRAULIC COMPONENTS OF SHIP’S ONBOARD DEVICES IN LOW AMBIENT TEMPERATURES
PublicationA large number of hydraulic devices and systems are started in low ambient temperatures. A good example of such a device is the hoisting winch on the ship. Starting hydraulic drive units in thermal shock conditions (rapid supply of hot oil to the cold unit) may lead to incorrect operation of the actuating system, for instance, due to the loss of clearance between cooperating elements. The article presents methods to prevent the...
-
Magnetic nanocomposites for biomedical applications
PublicationTissue engineering and regenerative medicine have solved numerous problems related to the repair and regeneration of damaged organs and tissues arising from aging, illnesses, and injuries. Nanotechnology has further aided tissue regeneration science and has provided outstanding opportunities to help disease diagnosis as well as treat damaged tissues. Based on the most recent findings, magnetic nanostructures (MNSs), in particular,...
-
Flame retardant epoxy/halloysite nanotubes nanocomposite coatings: Exploring low-concentration threshold for flammability compared to expandable graphite as superior fire retardant
PublicationEpoxy nanocomposites containing halloysite nanotubes (HNTs) were developed and their low-concentration thresholds for thermal stability and flame retardancy were compared with that of epoxy system containing expandable graphite (EG), as a reference with superior flame retardancy. The effects of HNTs and EG on the peak of Heat Release Rate (pHRR), Total Heat Release (THR), and Time-To-Ignition (TTI) of the prepared samples were...
-
Nodal models of Pressurized Water Reactor core for control purposes – A comparison study
PublicationThe paper focuses on the presentation and comparison of basic nodal and expanded multi-nodal models of the Pressurized Water Reactor (PWR) core, which includes neutron kinetics, heat transfer between fuel and coolant, and internal and external reactivity feedback processes. In the expanded multi-nodal model, the authors introduce a novel approach to the implementation of thermal power distribution phenomena into the multi-node...
-
FFT spectrum based matching algorithm for activedynamic thermography
PublicationIn Active Dynamic thermography (ADT) sequences of consecutive temperature distributions are analyzed. In biomedical applications of ADT, the problems of a patient's movements in front of a thermal camera should be eliminated before data analysis. Complete mechanical stabilization of the patients is impossible due to natural voluntary and involuntary moves caused by pulse breathing, etc. This paper presents a simple and efficient...
-
Study of the effect of adiabatic heating on the operation of the electrodynamic actuator
PublicationElectrodynamic actuators are used in hybrid switching systems where a very quick contact separation as well as operation repeatability and long-term reliability are required. The article presents selected results of thermal studies in the electrodynamic drive system. Study was carried out on the basis of the 3D electromagneto-thermal model implemented in the Ansys_Maxwell environment. The present model allows to determine the critical...
-
Measurement of the Temporal and Spatial Temperature Distribution on the Surface of PVCP Tissue Phantom Illuminated by Laser Dataset
PublicationThe dataset entitled Measurement of the temporal and spatial temperature distribution on the surface of PVCP tissue phantom illuminated by laser was obtained with a laboratory set-up for characterisation of the thermal properties of optical tissue phantoms during laser irradiation. The dataset contains a single image file representing the spatial temperature distribution on the surface of a PVCP tissue phantom. This thermal image...
-
New Technique of preparation of standard gas mixtures needed for validation of analytical procedures used in environmental studies
PublicationStandard gas mixtures are indispensable reference materials for ensuring the reliability of analytical work. Paper presents one novel approach in the field of production of gaseous reference materials based on the application of thermal decomposition process of proper surface compound for obtaining the desired gaseous analyte. The main fields of application of reference materials are presented. The field of application of thermal...
-
Experimental investigation on heat pipes supported by soy wax and lauric acid for electronics cooling
PublicationThis paper presents an experimental study of heat pipes for electronics cooling that were supported by energy storage materials (i.e. phase change materials - PCMs) coated at the adiabatic section. The PCMs utilized included two materials, namely lauric acid and soy wax, the latter being considered as a more cost-effective alternative. The study focused on three different powers: 20 W, 25 W, and 30 W. Both heating, cooling, and...
-
Current Trends in Wick Structure Construction in Loop Heat Pipes Applications: A Review
PublicationThermal control systems have been introduced as an important part of electronic devices, enabling thermal management of their electronic components. Loop heat pipe (LHP) is a passive two-phase heat transfer device with significant potential for numerous applications, such as aerospace applications, high-power LEDs, and solar central receivers. Its advantages are high heat transfer capability, low thermal resistance, long-distance...
-
Innovative Turbine Intake Air Cooling Systems and Their Rational Designing
PublicationThe improved methodology of the engine intake air cooling system designing based on the annual effect due to cooling was developed. It involves determining the optimal value of cooling capacity, providing the minimum system sizes at maximum rate of annual effect increment, and its rational value, providing a close to maximum annual effect without system oversizing at the second maximum rate of annual effect increment within the...
-
Surface active fatty acid ILs: Influence of the hydrophobic tail and/or theimidazolium hydroxyl functionalization on aggregates formation
PublicationNine structurally-related fatty acid ionic liquids have been prepared and their thermal behavior as well as their ability to self-assemble in water has been investigated. The thermal properties were studied by thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC), while the aggregation behavior was analyzed by tensiometry, isothermal titration calorimetry (ITC), conductometry, dynamic light scattering (DLS),...
-
Experimental and theoretical study on high-temperature creep of VT6 titanium alloy under multi-axial loading conditions
PublicationIn the framework of damage mechanics, we discuss a new mathematical model that describes the kinetics of the stress–strain state and damage accumulation during material degradation by the mechanism of long-term strength under complex multiaxial stress state. An experimental and theoretical technique is proposed for determination of material parameters and scalar constitutive functions for damaged media based on specially set experiments...
-
Analysis of cyclone separator solutions depending on spray ejector condenser conditions
PublicationThe core design strategy for minimizing CO2 emissions in gas power plant entails combining a spray ejector condenser (SEC) and separator to accomplish steam condensation and CO2 purification. This innovative process involves direct-contact condensation of steam with CO2, facilitated by interaction with a subcooled water spray, along with a cyclone separator mechanism intended for generating pure CO2. The investigation of the SEC...
-
NOx emission from a two-stroke ship engine: Part 2 – Laboratory test
Publication -
NOx emission from a two-stroke ship engine. Part 1: Modeling aspect
Publication -
An experimental study of emission and combustion characteristics of marine diesel engine with fuel pump malfunctions
Publication -
Application of the DSC analysis of thermoplastic polyurethane elastomers to a comparative study of their technological properties
Publication -
Primary and secondary crystallization of poly(ethylene adipate)
Publication -
Glass transition temperatures of polyurethane-urea elastomers based on N, N′-ethylenethiourea and N, N′-ethyleneurea as chain extenders
Publication -
Crystallization kinetics of poly(ethylene adipate) investigated by differential scanning calorimetry
Publication -
Heat and mass transfer in air-fed pressurised suits
PublicationOpisano konieczność modelowania transportu masy i ciepła w kombinezonach ochronnych. Omówiono różne sposoby modelowania wymiany ciepła, łącznie ze sprzężoną wymianą ciepła. Uwzględniono również ludzki metabolizm i turbulentne mechanizmy wymiany masy i ciepła. Publikacja opisuje również sposób modelowanie turbulentnych przepływów wieloskładnikowych. Pokazano również porównanie obliczeń z eksperymentem.
-
The Numerical Comparison of Heat Transfer in a Coated and Fixed Bed of an Adsorption Chiller
Publication -
Organic Rankine cycle turbogenerator cooling – Optimization of the generator water jacket heat exchange surface
Publication -
Theoretical methods in thermodynamics of condensed phases
Publication