Search
Filters
total: 3019
filtered: 2361
displaying 1000 best results Help
Search results for: LINEAR POLARIZATION RESISTANCE
-
Properties of surface layers of duplex stainless steel after burnishing processes
PublicationStress corrosion cracking resistance of cold worked layers of 25 Cr duplex stainless steel grade UR52N+ has been investigated. The surface layers were performed through burnishing treatment. The residual stresses at surface layers were determined using grazing angle incidence X-ray diffraction method (g-sin2 Ψ). Corrosion tests were performed with the use of Slow Strain Rate Test technique in boiling 35% MgCl2 solution. It has...
-
Wpływ kąta pochylenia koła na opór toczenia opon samochodowych
PublicationW pracy przedstawiono wpływ kąta pochylenia koła na opór toczenia opon do samochodów osobowych. Pomiary oporu toczenia kół toczących się z kątem pochylenia od -6º do +3º wykonano na bębnowej maszynie bieżnej metodą momentową. Wyniki pomiarów przedstawiono w formie zależności współczynnika oporu toczenia oraz przyrostu współczynnika oporu toczenia w funkcji kąta pochylenia badanego koła.
-
Cavitation behavior of the SUPERSTON alloy after laser treatment
PublicationResults of laser treatment at cryogenic conditions and its influence on microstructure, microhardness and cavitation resistance of the SUPERSTON alloy are presented in this paper. Obtained results point at possibility of the increase hardness and cavitation resistance of the parts worked in cavitation conditions.
-
Presence and distribution of antibiotic-resistant bacteria in multiphase activated sludge system
PublicationIn total 237 isolates of coliforms (113 strains) and enterococci (124 stains) from influent, mixed liquor in bioreactor and effluent of wastewater treatment plant (WWTP), were isolated on selective media and examined for antibiotic resistance. From 50 to 80% of the coliform strains isolated from the raw and treated sewage were resistant against ceftazidime CAZ, cefuroxim CXM, cefalotin KF and against amoxicillin AML, and only below...
-
Wood Moisture-Content Measurement Accuracy of Impregnated and Nonimpregnated Wood
PublicationThe influence of the impregnation process of pine wood (Pinus sylvestris L.) samples on the electrical resistance changes and the moisture-content measurement accuracy is presented in this paper. In this study, the resistances of impregnated and nonimpregnated green pine timber harvested from northern Poland were compared. An impregnation method based on a vacuum-pressure chamber was used. Copper salts were applied as the impregnated...
-
Bio-based semi-aromatic polyesters for coating applications
PublicationLinear and branched bio-based semi-aromatic (co)polyesters were evaluated as resins for solvent-basedand powder coatings. Dimethyl-2,5-furandicarboxylate (DMF), 2,3-butanediol and various multifunc-tional comonomers were used to synthesize amorphous hydroxyl-end-capped (co)polyesters. The resinswere cross-linked using the -caprolactam blocked trimer of isophorone diisocyanate. Both the solvent-based and powder coatings proved to...
-
Vibro piles performance prediction using result of CPT
PublicationVibro piles belong to the group of full displacement piles with an expanded base, characterised by a very high load capacity, especially in non-cohesive soils. The problem is to adopt a reliable method for the determination of full load–settlement (Q–s) curve. A frequent difficulty is the determination of the load capacity limit based on the static load test because the course of the load–settlement curve is of a linear nature....
-
Corrosion Properties of Dissimilar AA6082/AA6060 Friction Stir Welded Butt Joints in Different NaCl Concentrations
PublicationA solid-state friction stir welding method which is increasingly used in the marine and shipbuilding industry, has been developed to produce welds with high mechanical properties. In seawater, the oxide layer of aluminium is attacked by Cl− ions resulting in its disruption and formation of pitting corrosion. It is particularly important to determine the electrochemical properties of the produced welds and to evaluate the efect...
-
Failure of cold-formed beam: How does residual stress affect stability?
PublicationIn machine industry, stresses are often calculated using simple linear FEM analysis. Occasional failures of elements designed in such a way require recomputation by means of more sophisticated methods, eg. including plasticity and non-linear effects. It usually leads to investigation of failure causes and improvement of an element in order to prevent its unwanted behavior in the future. The study presents the case where both linear...
-
Computational complexity and length of recorded data for fluctuation enhanced sensing method in resistive gas sensors
PublicationThis paper considers complexity and accuracy of data processing for gas detection using resistance fluctuation data observed in resistance gas sensors. A few selected methods were considered (Principal Component Analysis – PCA, Support Vector Machine – SVM). Functions like power spectral density or histogram were used to create input data vector for these algorithms from the observed resistance fluctuations. The presented considerations...
-
Human-associated bacteria and their mobile genetic elements - important minority in wastewater and wastewater impacted ecosystems
PublicationSince human-associated bacteria have been recognized as vectors in two - way gene transmission between the pathogenic and environmental populations, health hazard connected with wastewater discharge requires reevaluation. In this paper the particular attention was given to antimicrobial-resistance of Escherichia coli and enterococci isolated from wastewater and wastewater impacted environments. The obtained results showed that...
-
Wpływ kierowcy na opór toczenia samochodu
PublicationW pracy omówiono wpływ zachowań kierowcy na opory toczenia pojazdu w ruchu drogowym. Można tu wyróżnić styl jazdy kierowcy oraz jego dbałość o pojazd. Przedstawiono wzrost oporu toczenia w aspekcie dynamicznego przyspieszania oraz szybkiej jazdy na zakręcie. Przeanalizowano także wpływ na opór toczenia takich czynników jak: ciśnienie w ogumieniu obciążenie promieniowe, zbieżność kół jezdnych samochodu oraz zużycie ogumienia.
-
Experimental study on polymer mass used to repair damaged structures
PublicationA new method of repairing damaged structures by injecting the cracks with specially designed polymer mass (flexible two-component grout based on polyurethane resin) has been recently proposed. The technique is mainly dedicated to damaged masonries, especially historical structures where minimum intervention is permitted. The cracks are filled with the special injection, forming the flexible joints bonding the disrupted structural...
-
Deep slot effect in the squirrel-cage induction motors with scalar (V/F) control
PublicationQualitative characteristics of the electrical drive considerably depend on identification accuracy of math model parameters. In particular, it is depend on detection accuracy of stator active resistance r1 that is used in calculation of flux linkages, rotary speed in sensorless control systems. Paper provides analysis of influence of stator deep slot effect to stator active resistance value
-
The geometry of free-standing titania nanotubes as a critical factor controlling their optical and photoelectrochemical performance
PublicationTitanium dioxide nanotubes are regarded as one of the most important functional materials and due to their unique electronic properties, chemical stability and photocorrosion resistance, they find applications in, for example, highly efficient photocatalysis or perovskite solar cells. Nevertheless, modification of TiO2 nanotubes is required to overcome their main drawback, i.e. large energy bandgap (>3.2 eV) limiting their ability...
-
Simple Measurement Method for Resistive Sensors Based on ADCs of Microcontrollers
PublicationA new, complete measurement method for resistance measurement of resistive sensors for systems based on microcontrollers equipped with analog-to-digital converters (ADCs) is proposed. The interface circuit consists of only four resistors, including a resistive sensor and a reference resistor, connected directly to the microcontroller pins. It is activated only during measurements, which significantly reduces power consumption....
-
Fluctuation-enhanced and conductometric gas sensing with nanocrystalline NiO thin films: A comparison
PublicationNanocrystalline thin films of NiO were prepared by advanced reactive gas deposition, and their responses to formaldehyde, ethanol and methane gases were studied via fluctuation-enhanced and conductometric methods Thin films with thicknesses in the 200–1700-nm range were investigated in as-deposited form and after annealing at 400 and 500 °C. Morphological and structural analyses showed porous deposits with NiO nanocrystals having...
-
Determination of Earth Pressure and Displacement of the Retaining Structure According to the Eurocode 7-1
PublicationComparative analysis of standard guidelines and findings given in EC7-1 and in Polish Standard PN-83/B-03010. Discussed guidelines concerning active and passive earth pressure as well as at rest pressure state. Wall displacement causing limit states of earth pressure and resistance. Interactive assumptions concerning intermediate earth pressure and resistance values. Conclusions and final remarks.
-
High-precision bearing estimation for active sonar with cylindrical array performed by interpolated array transformation
PublicationThe article presents a method for improving the accuracy of bearing in multibeam sonar with a cylindrical array. The antenna’s non-linear shape and the resulting non-uniform sampling of the signal in space, mean that known methods of high-resolution spectral analysis cannot be used. In order to apply an algorithm from this group, a linear virtual antenna must be produced. The paper presents a technique of mapping a cylindrical...
-
Correlation between natural frequencies and buckling load in a stiffened shell
PublicationThe paper deals with correlation between natural frequencies and buckling load of a stiffened shell composed of corrugated sheets and vertical stiffeners (columns). The simplified shell segment represents the buckling behaviour of a whole silo with sparsely distributed columns. The paper covers variants of linear buckling anal-yses, dynamic eigenvalue analyses and geometrically non-linear analyses of a segment modelled with shell...
-
High Dynamic Range Microwave Displacement and Rotation Sensors Based on the Phase of Transmission in Groove Gap Waveguide Technology
PublicationThis research is focused on the design and realization of displacement sensors in gap waveguide technology. It is shown that with a small but fundamental change in the structure of a conventional gap waveguide, a linear displacement can be sensed. To this end, a unique feature of gap waveguides, i.e. the fact that no electrical connection between the top and bottom parts of the gap waveguide is required, is used. It is further shown...
-
Effect of MAO coatings on cavitation erosion and tribological properties of 5056 and 7075 aluminum alloys
PublicationTwo ceramic coatings have been applied on 5056 and 7075 aluminum alloy by microarc oxidation (MAO) technology. The mass losses, surface morphologies and the phase constituents of the MAO coatings before and after cavitation tests were examined by means of digital scales, scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. In order to assess the impact of the mechanical properties of the surface layer on...
-
Review on Current Status of Echinocandins Use
PublicationFungal infections are rising all over the world every year. There are only five medical compound classes for treatment: triazoles, echinocandins, polyenes, flucytosine and allylamine. Currently, echinocandins are the most important compounds, because of their wide activity spectrum and much lower sides effects that may occur during therapy with other drugs. Echinocandins are secondary metabolites of fungi, which can inhibit the...
-
Further development of the poroelastic road surface within the new Polish project SEPOR
PublicationRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
The retrofitting of ships by applying retractable bow hydrofoils: a case study
PublicationIncreasing environmental requirements and a relatively long ship life of 30 years mean more attention is needed to retrofit existing ships. One possibility is using hydrofoils to reduce the ship’s resistance and improve comfort and safety in rough sea conditions. This study investigates the influence of retractable bow hydrofoils on the seakeeping performance and operational conditions of a selected case study vessel (V-shaped...
-
Usage of Two-Center Basis Function Neural Classifiers in Compact Smart Resistive Sensors
PublicationA new solution of the smart resistance sensorwith the Two-Center Basis Function (TCBF) neuralclassifier, for which the resistance sensor is a component ofan anti-aliasing filter of an ADC is proposed. Thetemperature measurement procedure is based on excitationof the filter by square impulses, sampling time response ofthe filter and processing measured voltage values by theTCBF classifier. All steps of the measurement procedure...
-
UV-Light-Induced Fluctuation Enhanced Sensing by WO3-Based Gas Sensors
PublicationWO3-based gas sensors were investigated under UV-light irradiation and at different working temperatures with the object of achieving superior sensitivity and selectivity. Resistance fluctuations in the WO3 layer were studied together with dc resistance measurements. The data were taken in synthetic air, ethanol, nitrogen dioxide, and mixtures of these gases. We conclude that UV irradiation can easily be applied to enhance the...
-
Generation and Propagation of Nonlinear Waves in a Towing Tank
PublicationThe paper presents the results of the research focused on linear and nonlinear wave generation and propagation in a deepwater towing tank equipped with a single flap-type wavemaker of variable draft. The problem of wave generation and propagation has been theoretically formulated and solved by applying an analytical method; linear and nonlinear solutions were obtained. The linear solution has been verified experimentally. The...
-
Investigation of stability and limit load of a truss overhead opened bridge
PublicationThe paper presents selected methods of determining stability and limit load of a truss top chord in opened bridges. These methods include linear buckling and non-linear static analysis based on the finite element method and algorithms based on design code procedures. The described methods were tested on an example of a steel footbridge situated in Straszyn. The results of stability analysis are compared. The results of geometrical...
-
Enhanced Spectroscopic Insight into Acceptor-Modified Barium Strontium Titanate Thin Films Deposited via the Sol–Gel Method
PublicationIn the present paper, composite thin films of barium strontium titanate (BaxSr1−xTiO3) with an acceptor modifier (magnesium oxide—MgO) were deposited on metal substrates (stainless steel type) using the sol–gel method. The composite thin films feature BaxSr1−xTiO3 ferroelectric solid solution as the matrix and MgO linear dielectric as the reinforcement, with MgO concentrations ranging from 1 to 5 mol%. Following thermal treatment...
-
Modeling of wood frame structures with different insulation materials under damaging dynamic loading
PublicationWood frame buildings are very popular in regions that are exposed to different dynamic excitations, such as damaging earthquakes. Their seismic resistance is really important in order to prevent structural damages and human losses. This paper presents the results of advanced numerical investigation carried out using the FEM. Based on the models of wall panels, the numerical model of real structure of the wood frame building has...
-
POM/EVA Blends with Future Utility in Fused Deposition Modeling
PublicationPolyoxymethylene (POM) is one of the most popular thermoplastic polymers used in the industry. Therefore, the interest in its potential applications in rapid prototyping is understandable. Nevertheless, its low dimensional stability causes the warping of 3D prints, limiting its applications. This research aimed to evaluate the effects of POM modification with ethylene-vinyl acetate (EVA) (2.5, 5.0, and 7.5 wt.%) on its processing...
-
Cavitation Erosion – Phenomenon and Test Rigs
PublicationThe cavitation and cavitation erosion phenomenon have been shortly presented. The main four types of test rigs to investigate the cavitation erosion resistance have been shown. Each type of test design is described and an example of a design is shown. A special attention has been payed to the designs described in the International ASTM Standards: a vibratory design and a cavitating jet cell. There was shown that the design of a...
-
A measurement method for lossy capacitive relative humidity sensors based on a direct sensor-to-microcontroller interface circuit
PublicationA new time-domain measurement method for determining the capacitance and resistance values of lossy relative humidity capacitive sensors is presented. The method is based on a direct sensor-to-microcontroller interface for microcontrollers with internal analog comparators and timers. The interface circuit consists only of four reference resistors (two reference resistors if a microcontroller includes a voltage reference source),...
-
Torsional buckling and post-buckling of columns made of aluminium alloy
PublicationThe paper concerns torsional buckling and the initial post-buckling of axially compressed thin-walled aluminium alloy columns with bisymmetrical cross-section. It is assumed that the column material behaviour is described by the Ramberg–Osgood constitutive equation in non-linear elastic range. The stationary total energy principle is used to derive the governing non-linear differential equation. An approximate solution of the equation...
-
Nexus between stock markets, economic strength, R&D and environmental deterioration: new evidence from EU-27 using PNARDL approach
PublicationThis research investigates the impact of stock market indices, economic strength, and research and development expenditures on environmental deterioration in the EU-27 countries for the period 2000–2020. This study utilized linear and non-linear panel ARDL to estimate the short- and long-run effect. According to the results, the stock market indices have negative effect on environmental deterioration in the symmetric form. However,...
-
Analytical approach for membrane action in laterally-restrained reinforced concrete square slabs under uniformly distributed loads
PublicationLaterally-restrained reinforced concrete slabs can mobilise compressive membrane action and subsequent tensile membrane action under extreme loading conditions, thereby enhancing the load resistance under uniformly distributed loads. Previous analytical study focuses primarily on tensile membrane action in simply-supported slabs. This paper describes an analytical approach for membrane action in laterally-restrained square slabs....
-
Analiza numeryczna i badania doświadczalne wpływu usytuowania stężeń na nośność wyboczeniową modelu kratownicy
PublicationIn the present research the results of experimental test and numerical analyses of a model of a typical truss are presented. The truss linear buckling analysis and non linear static analyses with respect to material and geometrical nonlinearity are conducted. For different stiffnesses and location of braces, the critical load and limit load for the truss are calculated and the threshold bracing stiffness is found. The results of...
-
Eigenfaces, Fisherfaces, Laplacianfaces, Marginfaces – How to Face the Face Verification Task
PublicationThis paper describes the exhaustive tests of four known methods of linear transformations (Eigenfaces, Fisherfaces, Laplacianfaces and Marginfaces) in the context of face verification task. Additionally, we introduce a new variant of the transformation (Laplacianface + LDA), and the specific interval-based decision rule. Both of them improve the performance of face verification, in general, however, our experiments show that the...
-
Direct shear stress vs strain relation for fiber reinforced composites
PublicationThe majority of fiber reinforced composites exhibit strong non-linear behavior in in-plane shear state. The effect is attributed to the micro-cracks appearing in the matrix and can be modeled on the micro and macro level. In this work the author proposes constitutive laws describing the non-linear in-plane shear response, which can be alternative for the relations commonly considered in the literature. The proposed equations are...
-
Detection of Polish clinical Aspergillus fumigatus isolates resistant to triazoles
PublicationWe studied the presence of triazole resistance of 121 Aspergillus fumigatus clinical isolates collected in two Polish cities, Warsaw and Wrocław, to determine if resistance is emerging in our country. We identified five itraconazole resistant isolates (4.13%) carrying the TR34/L98H alteration in Cyp51A gene, four of which were cross-resistant to posaconazole and one to voriconazole. One isolate was intermediate susceptible to itraconazole...
-
Charakterystyka oporności Klebsiella pneumoniae New Delhi na karbapenemy
PublicationBakterie Klebsiella pneumoniae New Delhi, posiadające gen oporności na karbapenemy (blaNDM) zostały po raz pierwszy wyizolowane w 2008 roku w Szwecji od pacjenta wcześniej hospitalizowanego w Indiach. Bakterie te szybko rozprzestrzeniają się po całym świecie, a od 2011 roku występują również w Polsce. Stanowią one wysokie ryzyko epidemiologiczne, ponieważ gen oporności na karbapenemy przekazywany jest pomiędzy bakteriami poprzez...
-
Mechanical and Microstructural Characterization of TIG Welded Dissimilar Joints between 304L Austenitic Stainless Steel and Incoloy 800HT Nickel Alloy
PublicationIn this article, the mechanical properties and microstructure of 304L austenitic stainless steel/Incoloy 800HT nickel alloy dissimilar welded joints are investigated. The joints were made of 21.3 mm × 7.47 mm tubes using the TIG process with the use of S Ni 6082 nickel filler metal. No welding imperfections were found and high strength properties of joints were obtained, meeting the assumed acceptance criteria of the product’s...
-
Simple synthesis route for fabrication of protective photo‐crosslinked poly(zwitterionic) membranes for application in non‐enzymatic glucose sensing
PublicationThis work focuses on the fabrication of non-enzymatic glucose sensing materials based on laser-formed Au nanoparticles embedded in Ti-textured substrates. Those materials possess good catalytic activity toward glucose oxidation in 0.1 × phosphate buffered saline as well as resistance to some interferants, such as ascorbic acid, urea, and glycine. The electrodes are further coated with three different polymers, that is, Nafion,...
-
DETERMINATION OF SEAKEEPING PERFORMANCE FOR A CASE STUDY VESSEL BY THE STRIP THEORY METHOD
PublicationThe increase of seakeeping performance is of particular importance for car and passenger ferries, service ships in the gas and oil extraction industry and offshore wind power farm industry, as well as for special purpose ships (including military applications). In the water areas of the Baltic Sea, North Sea, and Mediterranean Sea, which are characterised by a short and steep wave, the hull shape has a substantial impact on the...
-
3D buckling analysis of a truss with horizontal braces
PublicationThe present research is devoted to the study of out-of-plane buckling of a truss with horizontal braces. The truss is a model of real roof truss scaled by factor ¼. A linear buckling and a non-linear analysis with geometric and material nonlinearity were carried out. The truss buckling and limit load for different stiffnesses and number of braces are found. Numerical analysis are verified by experiment. Threshold bracing stiffness...
-
The consideration to the dynamic systems parameter identification
PublicationIn this paper, a concept for continuous-time dynamic systems parameter identification using modulating function approach is presented. It refers to linear as well as selected non-linear systems. It shows the possibility of direct application without converting differential equation. In particular cases direct application can decrease the amount of computation in non-linear system identification, which generally requires Fourier...
-
Krzywa przejściowa z wygładzoną krzywizną dla dróg kolejowych
PublicationW pracy przedstawiono koncepcję nowej postaci krzywej przejściowej, o liniowym przebiegu krzywizny na długości i wygładzonymi rejonami skrajnymi. Może ona stanowić alternatywę dla tzw. gładkich krzywych przejściowych, o nieliniowym przebiegu krzywizny na całej długości. Została tutaj wykorzystana uniwersalna metoda identyfikacji krzywych przejściowych za pomocą równań różniczkowych. Wyznaczono ogólne równania krzywizny oraz odpowiednie...
-
Drug-resistant and hospital-associated Enterococcus faecium from wastewater, riverine estuary and anthropogenically impacted marine catchment basin.
PublicationEnterococci, ubiquitous colonizers of humans and other animals, play an increasingly important role in health-care associated infections (HAIs). Acquisition of resistance determinants not only seriously limits available therapeutic options but also increases available gene pool for other species. It is believed that the recent evolution of two clinically relevant species, Enterococcus faecalis and Enterococcus faecium occurred...
-
Polyester sail technical woven fabric behaviour under uniaxial and biaxial tensile tests
PublicationThe paper is focused on the identification of mechanical properties of a sail technical woven fabric (yacht sailcloth polyester) style 480 AP with MTO (Medium Tempered Optimized) finish. The non-linear elastic behaviour of the fabric applied for sails is investigated under uniaxial and biaxial tensile tests. Comparison of non-linear elastic parameters with others polyester coated fabrics is made. This paper is intended to be an...