Search
Filters
total: 2200
filtered: 1979
displaying 1000 best results Help
Search results for: gas turbine cycles
-
Partial Admission Stages of High Efficiency for a Microturbine
PublicationThe paper presents the results of a design analysis of a micro-turbine for a co-generation micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attention was...
-
Operation of the 900 MW power plant with the ORC supplied from three heat sources
PublicationThe chapter is aimed at utilisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90°C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach to increase...
-
Review of Methods for Diagnosing the Degradation Process in Power Units Cooperating with Renewable Energy Sources Using Artificial Intelligence
PublicationThis work is based on a literature review (191). It mainly refers to two diagnostic methods based on artificial intelligence. This review presents new possibilities for using genetic algorithms (GAs) for diagnostic purposes in power plants transitioning to cooperation with renewable energy sources (RESs). The genetic method is rarely used directly in the modeling of thermal-flow analysis. However, this assignment proves that the...
-
Analysis of "green methanol" production from carbon dioxide acquired from negative emission power plants using CFD approach for catalytic reactor
PublicationThe growing global demand for energy, coupled with the urgent need to reduce carbon dioxide (CO₂) emissions, has led to the development of innovative energy cycles such as the negative CO₂ gas power plant (nCO2PP). Carbon dioxide storage and reuse in current industries is therefore becoming an important issue. The answer to this is the process of synthesizing methanol, commonly used in many industries from captured carbon dioxide...
-
Chapter 7: Engineering Thermodynamics and the Carnot Cycle
PublicationThe chapter presents information about thermodynamics and thermodynamic cycles, especially the history and meaning of Carnot Cycle as well as P-v and T-s Diagrams
-
Remote Health Monitoring of Wind Turbines Employing Vibroacoustic Transducers and Autoencoders
PublicationImplementation of remote monitoring technology for real wind turbine structures designed to detect potential sources of failure is described. An innovative multi-axis contactless acoustic sensor measuring acoustic intensity as well as previously known accelerometers were used for this purpose. Signal processing methods were proposed, including feature extraction and data analysis. Two strategies were examined: Mel Frequency Cepstral...
-
Slowly-closing valve behaviour during steam machine accelerated start-up
PublicationThe paper discusses the state of stress in a slowly-closing valve during accelerated start-up of a steam turbine. The valve is one of the first components affected by high temperature gradients and is a key element on which the power, efficiency and safety of the steam system depend. The authors calibrated the valve model based on experimental data and then performed extended Thermal-FSI analyses relative to experiment. The issue...
-
Network Graph Transformation Providing Fast Calculation of Paths for Resilient Routing
PublicationProtection of transmission against failures can be appropriately dealt with by alternative paths. However, common schemes (e.g., Bhandaris scheme) are characterized by a remarkable delay while determining the transmission paths. This in turn may have a serious impact on serving dynamic demands (characterized by relatively short duration time). As a remedy to this problem, we introduce an approach to pre-compute the sets of disjoint...
-
Ocena sprawności cyklu roboczego Pojazdu do Usuwania Odpadów z Pojemników na podstawie danych eksploatacyjnych
PublicationW artykule przedstawiona została metoda oceny sprawności cyklu roboczego śmieciarki. Wykorzystując dane eksploatacyjne wyznaczono dwa reprezentatywne cykle i na ich podstawie obliczono zarówno sprawność całego cyklu, jak i jego poszczególnych faz. Porównano wartości energii potrzebnej do opróżniania pojemników, energii do zagęszczania odpadów oraz energii z paliwa. Przedstawiono przebiegi mierzonych i obliczonych wartości w czasie...
-
POTENTIAL APPLICATIONS OF ELECTRONIC NOSE BASED ON ULTRA FAST GAS CHROMATOGRAPHY TO DISTINGUISH ALCOHOLIC BEVERAGES MADE OF GRAIN = POTENCJALNE MOŻLIWOŚCI ZASTOSOWANIA ELEKTRONICZNEGO NOSA OPARTEGO NA ULTRA SZYBKIEJ CHROMATOGRAFII GAZOWEJ DO ODRÓŻNIANIA NAPOJÓW SPIRYTUSOWYCH POCHODZENIA ZBOŻOWEGO
PublicationStan środowiska a zwłaszcza powietrza ma wpływ na wiele aspektów życia, m in. na jakość produktów spożywczych. Z tego względu niezwykle ważne jest monitorowanie stanu środowiska, które odbywa się za pomocą wielu technik analitycznych. Jedną z nich jest elektroniczny nos. Pierwotnie elektroniczny nos był wykorzystywany tylko do badania uciążliwości zapachowej powietrza. Obecnie technika ta wykorzystywana jest również do monitorowania...
-
Nowoczesne techniki przygotowania próbki do oznaczania analitów organicznych z zastosowaniem chromatografii gazowej. Część I. Podstawy teoretyczne ekstrakcji. Modern techniques of preparation of samples for determining organic analytes by gas chromatography. Part I. Theoretical principles of extraction.
PublicationPrzedstawiono podstawy teoretyczne technik izolacji i wzbogacania analitów organicznych z próbek gazowych oraz ciekłych. Już pobieżna analiza literatury dotyczącej omawianych zagadnień, pokazuje jak różnorodne i bogate spektrum technik jest stosowane na etapie przygotowania próbki. Z drugiej strony, z punktu widzenia podstaw fizykochemicznych, większość technik opiera się na dwóch zjawiskach: adsorpcji analitów na medium zatrzymującym...
-
Some Aspects of Designing Nozzle Segments of Axial Microturbines,
PublicationIn the paper a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of the numerical calculations and experimental investigations are presented, followed by an appropriate discussion and conclusions.
-
Wavelet transform analysis to assess oscillations in pial artery pulsation at the human cardiac frequency
PublicationPial artery adjustments to changes in blood pressure (BP)may last only seconds in humans. Using a novelmethod called near-infrared transillumination backscattering sounding (NIR-T/BSS) that allows for the non-invasive measurement of pial artery pulsation (cc-TQ) in humans, we aimed to assess the relationship between spontaneous oscillations in BP and cc-TQ at frequencies between 0.5 Hz and 5 Hz. We hypothesized that analysis of...
-
Wieloobszarowa regulacja systemu turbogeneratora elektrowni jądrowej =Multiregional control of nuclear power plant turbogenerator system
PublicationW artykule przedstawiono propozycję zaawansowanej struktury sterowania układem turbogeneratora w szerokim zakresie zmian zapotrzebowania na moc czynną. Dla potrzeb syntezy tej struktury wykorzystano nieliniowe, dynamiczne modele turbiny parowej i generatora synchronicznego współpracującego z systemem elektroenergetycznym. Zaproponowane algorytmy sterowania oparte są odpowiednio o wieloobszarowe regulatory rozmyte, z lokalnymi regulatorami...
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 2/2
PublicationThe process of conversion of wind kinetic energy into electricity in innovative wind power plant emits practically no harmful substances into the environment. However, the production stage of its components requires a lot of energy and materials. The biggest problem during production plan-ning process of an innovative wind power plant is selection of materials and technologies and, consequently, the waste generated at this stage....
-
Electrodes consisting of PEDOT modified by Prussian Blue analogues deposited onto titania nanotubes – Their highly improved capacitance
PublicationIn this work we present the outstanding energy storage of prepared inorganic-organic heterojunction where hydrogenated ordered titania nanotubes (H-TiO2NT) were modified by the hybrid made of poly(3,4-ethylenedioxythiophene) (pEDOT) and iron hexacyanoferrate centres (Fehcf, Prussian Blue). The material TiO2NT/pEDOT:Fechf was obtained electrochemically by means of: anodization, hydrogenation and finally, electropolymerization of...
-
The influence of moderate pressure and subzero temperature on the shelf life of minced cod, salmon, pork and beef meat
PublicationThe effect of moderate pressure at subzero temperature on natural microflora of minced cod, salmony, pork and beef meat was studied. Pressure of 193 MPa at –20 °C caused reduction of total bacterial count in pork and beef meat by 1.1 and 0.6 log cycles, respectively, and by about 1.5 log cycles in fish meat. Under these conditions the psychrophilic and psychrotophic bacteria were below the detection limit (<10CFU/g of sample) in...
-
The dynamic performance analysis of the Micro-turbine's rotor supparted on slide and roling element bearings
PublicationThis article presents the results of investigations of dynamic characteristics of a small-dimension rotor with slide and rolling element bearings. The object of investigations was the rotor-bearing system designed for the ORC based low-power steam micro-turbine. The investigations were performed using MESWIR series programs, as well as commercial FEA software ABAQUS and MADYN 2000. The results of modal analysis of the micro-rotor...
-
DESIGN AND STRENGTH CALCULATIONS OF THE TRIPOD SUPPORT STRUCTURE FOR OFFSHORE POWER PLANT
PublicationThe support structure being the object of the analysis presented in the article is Tripod. According to the adopted assumptions, it is a foundation gravitationally set in the water region of 60 m in depth, not fixed to the seabed, which can be used for installing a 7MW wind turbine. Due to the lack of substantial information on designing and strength calculations of such types of structures in the world literature, authors have...
-
The paired-domination and the upper paired-domination numbers of graphs
PublicationIn this paper we obtain the upper bound for the upper paired-domination number and we determine the extremal graphs achieving this bound. Moreover we determine the upper paired- domination number for cycles.
-
Determination of carbonyl compounds in distilled alcoholic beverages using gas chromatography and head-space solid phase microextraction. Oznaczanie związków karbonylowych w napojach alkoholowych z użyciem chromatografii gazowej i mikroekstrakcji do fazy stacjonarnej z fazy nadpowierzchniowej
PublicationW pracy przedstawiono badania nad opracowaniem procedury oznaczania związków karbonylowych z użyciem mikroekstrakcji do fazy stacjonarnej w wersji analizy fazy nadpowierzchniowej (HS-SPME), chromatografii gazowej z detekcją wychwytu elektronów(GC-ECD) oraz derywatyzacji pentafluorobenzylohydroksyloaminą (PFBHA). Opisano wpływ parametrów: temperatury, mieszania, czasu ekspozycji włókna, dodatku soli, stężenia alkoholu. Opracowaną...
-
DETEKCJA FAL UDERZENIOWYCH W UKŁADACH ŁOPATKOWYCH CZĘŚCI NISKOPRĘŻNYCH TURBIN PAROWYCH
PublicationW artykule przedstawiono wyniki numerycznych symulacji okołodźwiękowego przepływu pary przez ostatnie stopnie części niskoprężnej turbiny o mocy 50 MW. Celem przeprowadzonych symulacji była detekcja oraz lokalizacja fali uderzeniowej, występującej dla przyjętej geometrii układu łopatkowego. Przeanalizowano również wpływ zmiany wartości ciśnienia na wlocie do rozpatrywanych stopni turbiny na maksymalną wartość...
-
The distributed model predictive controller for the nuclear power plant turbo-generator set
PublicationTypically there are two main control loops with PI controllers operating at each turbo-generator set. In this paper a distributed model predictive controller DMPC, with local QDMC controllers for the turbine generator, is proposed instead of a typical PI controllers. The local QDMC controllers utilize step-response models for the controlled system components. These models parameters are determined based on the proposed black-box...
-
Estimation of the steam condensation flow via CFD methods
PublicationThe results of numerical simulations to predict the performance of different steam models have been presented. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine stage. For numerical analysis three models have been finally used – the ideal steam model without condensation, an equilibrium steam...
-
Robustness Analysis of a Distributed MPC Control System of a Turbo-Generator Set of a Nuclear Plant – Disturbance Issues
PublicationTypically, there are two main control loops with PI controllers operating at each turbo-generator set. In this paper, a distributed model predictive controller with local quadratic model predictive controllers for the turbine generator is proposed instead of a set of classical PI controllers. The local quadratic predictive controllers utilize step-response models for the controlled system components. The parameters of these models...
-
ENHANCED EVAPORATION OF THE DROPLETS OF CONDENSATE IN THE ASYMMETRICAL SHOCK WAVE ZONE
PublicationIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages [4,5]. The formation and evolution of these droplets lower the performance of the wet stages of the turbines, and their effects on the efficiency are collectively known as wetness losses [4]. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current....
-
Toward Fast Calculation of Communication Paths for Resilient Routing
PublicationUtilization of alternate communication paths is a common technique to provide protection of transmission against failures of network nodes/links. However, a noticeable delay is encountered when calculating the relevant sets of disjoint paths using the available algorithms (e.g., using Bhandari’s approach). This, in turn, may have a serious impact on the ability of a network to serve dynamic demands...
-
Wstępne badania technologii spawania złączy narożnych ze stali niskoweglowej i nierdzewnej o grubości g=6mm i g=10mm
PublicationCelem pracy był dobór parametrów spawania dla spoin narożnych o grubości 6mm i 10mm próbek wykonanych ze stali niskowęglowej S355 i stali nierdzewnej - typu 304 (X6CrNI18-10). Złącza były spawane laserowo, jednostronnie z pełnym przetopem a powierzchnie lica i grani zapewniają uzyskanie szczelności przylegającego elementu uszczelniającego. Próbki zostały dostarczone przez Zleceniodawcę. Próby zostały przeprowadzone na stanowisku...
-
Pracujący w czasie rzeczywistym system detekcji gazów wykorzystujący przenośny komputer Raspberry PI oraz matrycę półprzewodnikowych czujników gazu
PublicationThe gas-analyzing systems based on the array of partially selective gas sensors and pattern-recognition techniques are potentially fast and lowcost alternative for other devices, like gas‑analysers. They give the possibility of recognition the type and the concentration of measured volatile compounds in their working environment. In this work we present the implementation of gas recognition system, in which the signals from an...
-
Corrosion performance of super duplex stainless steel and pipeline steel dissimilar welded joints: a comprehensive investigation for marine structures
PublicationThis study investigates the corrosion behavior of dissimilar gas tungsten arc (GTA) welded joints between super duplex stainless steel (sDSS 2507) and pipeline steel (X-70) using electrochemical and immersion corrosion tests. The GTA welds were fabricated using ER2594 and ER309L fller metals. The study examined the electrochemical characteristics and continuous corrosion behavior of samples extracted from various zones of the weldments...
-
An O ( n log n ) algorithm for finding edge span of cacti
PublicationLet G=(V,E) be a nonempty graph and xi be a function. In the paper we study the computational complexity of the problem of finding vertex colorings c of G such that: (1) |c(u)-c(v)|>=xi(uv) for each edge uv of E; (2) the edge span of c, i.e. max{|c(u)-c(v)|: uv belongs to E}, is minimal. We show that the problem is NP-hard for subcubic outerplanar graphs of a very simple structure (similar to cycles) and polynomially solvable for...
-
Evaluation of the efficiency of the duty cycle of refuse collection vehicle based on real-world data
PublicationIn this paper a method of the efficiency evaluation of the duty cycle of Refuse Collection Vehicle is presented. Using real world data, two representative duty cycles were analysed. Total cycle efficiency was calculated, as well as the efficiency of particular cycle phases. Then, energy needed to collect and compact the waste and energy from fuel were compared. Measured and calculated values were shown on the diagrams illustrating...
-
Zastosowanie połączenia mikroekstrakcji do fazy stacjonarnej i chromatografii gazowej do oznaczania lotnych kwasów tłuszczowych w próbkach środowiskowych i pokrewnych=Application of combination of solid phase microextraction and gas chromatography for determination of volatile fatty acids in environmental and related samples
PublicationOznaczanie lotnych kwasów tłuszczowych (LKT) w próbkach środowiskowych wymaga najczęściej izolacji i wzbogacania analitów na etapie przygotowania próbek oraz zastosowania techniki o dużym potencjale separacyjnym i identyfikacyjnym na etapie oznaczeń końcowych. W pracy dokonano krytycznego przeglądu zastosowań wygodnej i często stosowanej techniki mikroekstrakcji do fazy stacjonarnej (SPME) w połączeniu z wysokosprawną techniką...
-
Incorporation of the sulfur cycle in sustainable nitrogen removal systems - A review
PublicationIn wastewater treatment systems, sulfur (S) removal processes are generally based on heterotrophic sulfate (SO42−) reduction by sulfate reducing bacteria and S-dependent autotrophic denitrification by sulfur oxidizing bacteria. A combination of either two cycles (N and S) or three cycles (N, S and C) appears to be a viable approach to sustainable wastewater treatment, resulting in energy savings and reduction of sludge production....
-
Management of low-temperature heat source by ORC aided by additional heat source
PublicationThe presented work is aimed at utilisation of waste heat in the manner to produce electricity in ORC installation. Therefore the precondition of the study was to use the waste heat available in the form of a stream of hot water at 90°C. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. That was the incentive to search for the ways of increasing the temperature of the...
-
Advanced operating methods
PublicationSelected operating methods of resistive gas sensors were presented. The methods utilize flicker noise (1/f noise), which gives additional information about ambient gas when compared with the recorded changes of DC resistance only. Methods of flicker noise measurements were outlined. Recently developed prototype gas sensors comprising golden nanoparticle functionalized with organic ligands can generate intense flicker noise induced...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublicationIn the paper presented is a concept to utilize waste heat from the power plant with the aid of the low-temperature ORC cycle. The ORC system is heated from two heat sources, the first one being the flow rate of waste heat obtained from the exhaust gases. Subsequently, the working fluid in the cycle is additionally heated by the condensing steam from the low pressure turbine extraction points increasing in such way the level of...
-
Zastosowanie metod eksploracji danych do analizy odpowiedzi czujników gazu
PublicationZagadnienia poruszane w niniejszej rozprawie dotyczą zastosowania metod eksploracji danych do analizy odpowiedzi czujników gazu, umożliwiających poprawną identyfikację składu mieszaniny gazowej w elektronicznych systemach rozpoznawania gazu. Elektroniczne systemy rozpoznawania gazu to urządzenia wykorzystujące czujniki gazu oraz odpowiednio dobrane metody analizy danych pomiarowych, zdolne do określenia składu mierzonej mieszaniny...
-
The Emission and Combustion Characteristics of Marine Diesel Engine with Extreme Throttled of Air or Exhaust Ducts
PublicationPresented paper shows the results of the laboratory tests on the relationship between the extreme throttling of both air intake duct and exhaust gas duct and gaseous emission from the marine engine. The object of research is a laboratory, 4-stroke, DI diesel engine, operated at loads from 50 kW to 250 kW at a constant speed equal to 750 rpm. During the laboratory tests the thermodynamic and exhaust gas emission characteristics...
-
TOXIC GASES IDENTIFICATION USING SINGLE ELECTROCATALYTIC SENSOR RESPONSES AND ARTIFICIAL NEURAL NETWORK
PublicationThe need for precise detection of toxic gases drives development of new gas sensors structures and methods of processing the output signals from the sensors. In literature, artificial neural networks are considered as one of the most effective tool for the analysis of gas sensors or sensors arrays responses. In this paper a method of toxic gas components identification using a electrocatalytic gas sensor as a detector and an artificial...
-
Thermodynamic and economic analysis of nuclear power unit operating in partial cogeneration mode to produce electricity and district heat
PublicationThis paper presents the methodology of techno-economic analysis for a nuclear unit operating in partial cogeneration mode and its application for the case study: a nuclear power plant planned in Poland. The research objectives were: to propose EPR, AP1000 and ESBWR nuclear condensing-extraction turbine systems modifications required for operation in cogeneration, to determine optimal heat production and heat transport line (HTL)...
-
Mechanical behaviour of knit synthetic mesh used in hernia surgery
PublicationPurpose: There is a discussion in literature concerning mechanical properties and modelling of surgical meshes. An important feature of elastic modulus dependency on load history is taken into account in this paper, as implants are subjected to variable loading during human activity. The example of DynaMesh®-IPOM surgical implant is studied. Methods: The analysis is based on failure tension tests and cyclic loading and unloading...
-
The phenomenon of increasing capacitance induced by 1T/2H-MoS2 surface modification with Pt particles – Influence on composition and energy storage mechanism
PublicationIn this paper, several approaches to the synthesis of molybdenum-based electrode materials for supercapacitors are presented, including anodization, hydrothermal process and annealing. For the material prepared via anodization of a molybdenum plate, followed by a hydrothermal process in thiourea aqueous solution, a thorough study of the Pt-surface modification through repetitive cycling in 1 M sulfuric acid with Pt acting as a...
-
The impact of freeze-thaw processes on a cliff recession rate in the face of temperate zone climate change
PublicationFreeze-thaw action is a common type of geomorphological processes eroding cliff faces in the temperate climate zone. In our previous study, we assessed the geomorphological effects of freeze-thaw fluctuations occurring within the cliff of Jeziorsko Reservoir (central Poland). Based on those findings, we have now determined the number of freeze-thaw cycles to assess their historical impact on the studied cliff. We have also traced...
-
“Shadow” vs. “Phase 3D” method within endoscopic examinations of marine engines
PublicationA visual investigation of surfaces creating internal, working spaces of marine combustion engines by means of specialized view-finders so called endoscopes is at present almost a basic method of technical diag-nostics. The surface structure of constructional material is visible during investigations like through the magnifying glass (usually with a precisely determined magnification), which makes possible a detection, recognition...
-
Permeation and sorption properties of poly(ether-block-amide) membranesfilled by two types of zeolites
PublicationThe experimental study of transport properties of mixed matrix membranes (MMMs) based on PEBA-4033 with two types of zeolites is reported. Gas (CO2, O2, N2) and vapor (benzene, toluene, methanol, water) permeation measurements were performed using the differential flow permeameter at temperature of 298.15 K and at atmospheric pressure. Gas/vapor permeation was monitored by measuring the changes of the thermal conductivity of carrier...
-
Widening of the electroactivity potential range by composite formation – capacitive properties of TiO2/BiVO4/PEDOT:PSS electrodes in contact with an aqueous electrolyte
PublicationComposites based on the titania nanotubes were tested in aqueous electrolyte as a potential electrode material for energy storage devices. The nanotubular morphology of TiO2 was obtained by Ti anodization. TiO2 nanotubes were covered by a thin layer of bismuth vanadate using pulsed laser deposition. The formation of the TiO2/BiVO4 junction leads to enhancement of pseudocapacitance in the cathodic potential range. The third component,...
-
Influence of cyclic frozen and defrost on mechanical properties of polytetrafluoroethylene (PTFE)-coated woven fabrics
PublicationThis research aims to determine the influence of the cyclic process of freezing and defrosting on the mechanical properties of the chosen glass fibres and PTFE-coated woven fabrics. The specimens were subjected to freezing at about −20 °C for 4 h and thawing by full immersion into the water at about +20 °C for 4 h. The fabric samples after 25 and 50 frozen cycles were air-dried at room temperature for one week and then subjected...
-
FORECASTING BIOGAS FORMATION IN LANDFILLS
Publication: The aim of the present research was to develop a mathematical model for estimating the amount of viscous gas generated as a function of weather conditions. Due to the lack of models for predicting gas formation caused by sudden changes in weather conditions in the literature, such a model was developed in this study using the parameters of landfills recorded for over a year. The effect of temperature on landfill gas production...
-
Make lighting healthier
PublicationLife on Earth evolved in day-and-night cycles. Plants and animals, including insects such as the fruit fly, have a biological clock that controls their circadian rhythms — as the 2017 winners of the Nobel Prize in Physiology or Medicine showed. Now, humans’ increasing reliance on artificial lighting is changing those rhythms.