Filters
total: 689
filtered: 655
Search results for: numerical modelling
-
Safety at railway level crossings and Vision Zero
PublicationIn this work, safety analysis at the railway level crossings is presented using advanced mathematical modelling. Resistivity of track subgrade panels is taken into account. The analysis does not refer to the assessment of the current regulations. Specific cases of generalized dynamic system are considered by introducing operations S=Δ, S=P defined in space C(N) of real sequences. In this model, generalized discrete exponential...
-
A 95-Year-Old Concrete Arch Bridge: From Materials Characterization to Structural Analysis
PublicationThe structural analysis of a 95-year-old concrete arch bridge located in Jagodnik (Poland) is performed in this paper, in order to check its behavior under today’s traffic loads. The mechanical properties of both the concrete and the reinforcement are investigated by testing cores and bar stubs extracted from the bridge. Structural analysis confirms that the bridge meets today’s load requirements in terms of bearing capacity, serviceability...
-
The Discrete-Continuous, Global Optimisation of an Axial Flow Blood Pump
PublicationThis paper presents the results of the discrete-continuous optimisation of an axial flow blood pump. Differential evolution (DE) is used as a global optimisation method in order to localise the optimal solution in a relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump are performed by means of the Reynolds-Average Navier-Stokes...
-
Mathematical modeling of hydrogen production performance in thermocatalytic reactor based on the intermetallic phase of Ni3Al
PublicationThe main goal of the following work is to adjust mathematical modelling for mass transfer, to specific conditions resulting from presence of chemical surface reactions in the flow of the mixture consisting of helium and methanol. The thermocatalytic devices used for decomposition of organic compounds incorporate microchannels coupled at the ends and heated to 500 oC at the walls regions. The results of the experiment were compared...
-
Discrete-continuous optimisation of an axial flow blood pump
PublicationThis paper presents results of discrete-continuous optimisation of an axial flow blood pump. Evolution Strategies (ES) are used as a global optimisation method in order to localise the optimal solution in relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump is performed by means of the Reynolds-Average Navier-Stokes...
-
LDFEM analysis of FDP auger installation in cohesive soil
PublicationThis paper deals with large deformation finite element (LDFE) preliminary modelling of Full Displacement Pile (FDP) installation in cohesive soil deposit located in Jazowa, Poland. The detailed FDP auger geometry is applied and the drilling process is modelled with full 3D Coupled Eulerian-Lagrangian (CEL) formulation. The total stress approach and elastic-perfectly plastic model with rate-dependent Mises plasticity is used. The...
-
Modelling the time-dependent behaviour of soft soils
PublicationTime-dependence of soft soils has already been thoroughly investigated. The knowledge on creep and relaxation phenomena is generally available in the literature. However, it is still rarely applied in practice. Regarding the organic soils, geotechnical engineers mostly base their calculations on the simple assumptions. Yet, as presented within this paper, the rate-dependent behaviour of soft soils is a very special and important...
-
Areas of Updraft Air Motion in an Idealised Weather Research and Forecasting Model Simulation of Atmospheric Boundary Layer Response to Different Floe Size Distributions
PublicationPresented dataset is part of a numerical modelling study focusing on the analysis of the influence of sea ice floe size distribution (FSD) on the horizontal and vertical structure of convection in the atmosphere. The total area and spatial arrangement of the up-drafts indicates that the FSD affects the total moisture content and the values of area averaged turbulent fluxes in the model domain. In fact, while convective updrafts...
-
Simplified approach to assess the dynamic response of a container ship subjected to bow slamming load
PublicationSimplified approach to assess the dynamic response of a container ship subjected to the bow slamming load, resulting in a transient vibratory response, typically called a 'whip-ping', is presented. The accurate numerical modelling is very complex and involves cou-pling of the hydrodynamic and structural solution at every time step, leading to huge com-putational and workload cost. Thus, the one-way coupling methodology is adopted,...
-
Application of advanced CFD simulations in seakeeping analysis of ships (case study)
PublicationThe novel design process of many types of ships needs estimation of seakeeping properties. Especially ships like Offshore Supply Vessels, Wind Farm Support Vessels, Research Vessels, ferries, military vessels, rescue vessels require extended analysis of ship behavior on rough sea. The main reason for improving ships operability in different sea conditions is need of rising efficiency of propulsion system, reducing hull added resistance,...
-
An advanced Thermal-FSI approach to flow heating/cooling
PublicationActually, two-way thermal-energy exchange between working fluid and solid material of a casing is a leading problem for modern – semi automatic – design techniques. Many questions should be solved, especially, the turbulent mode of thermal energy transport both in fluid and solid, should be re-examined and reformulated from the primary principles. In the present paper, a group of researchers from Energy Conversion Department of...
-
On a 3D material modelling of smart nanocomposite structures
PublicationSmart composites (SCs) are utilized in electro-mechanical systems such as actuators and energy harvesters. Typically, thin-walled components such as beams, plates, and shells are employed as structural elements to achieve the mechanical behavior desired in these composites. SCs exhibit various advanced properties, ranging from lower order phenomena like piezoelectricity and piezomagneticity, to higher order effects including flexoelectricity...
-
Modelling of the Baumann turbine stage operation Part II. Free and kinetic vibrations
PublicationIn this paper has been presented a methodology of validation a novel mathematical model dedicated to evaluation and prediction of material degradation and demage of steam turbine elements such as blades, valves and pipes due to three mechanisms: stress-corosion, high-temperature creep and low-cyclic fatigue. The validation concept is based on an experimental setup manufactured in the Laboratory of Faculty of Mechanical and Power...
-
Collective citizens' behavior modelling with support of the Internet of Things and Big Data
PublicationIn this paper, collective human behaviors are modelled by a development of Big Data mining related to the Internet of Things. Some studies under MapReduce architectures have been carried out to improve an efficiency of Big Data mining. Intelligent agents in data mining have been analyzed for smart city systems, as well as data mining has been described by genetic programming. Furthermore, artificial neural networks have been discussed...
-
Simplified Method of Modelling Behaviour of Ship in Waves with Partially Flooded Compartments
PublicationThis paper contains a description of a numerical model for calculating behaviour of ships in waves. There are many models available, but the one described here can be characterised with a set of parameters that have a decisive impact on the final values of roll motion amplitude and frequency. In this paper, it is shown how a fitting of a standard-shape hull characterised by certain readily available parameters affects...
-
FEM modelling of screw displacement pile interaction with subsoil
PublicationPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
Backscattering properties of southern Baltic herring
PublicationReliable TS(L) relationship is required to improve acoustic algorithms of abundanceestimation of Baltic herring. The relationships, empirically obtained in different parts of theBaltic Sea, produce up to 8 dB – difference in the herring TS. In order to develop an accurateTS(L) relationship, it is important to analyze factors controlling the TS variability. Thepossible impact of the regional difference...
-
Impact of the Artificial Strait in the Vistula Spit on the Hydrodynamics of the Vistula Lagoon (Baltic Sea)
PublicationIn the Vistula Lagoon, storm surges are induced by variable sea levels in the Gulf of Gdańsk and wind action. The rising of the water level in the southern part of the basin, exceeding 1.0 m above mean sea level, can be dangerous for the lowland area of Żuławy Elbląskie, causing the inundation of the polders adjacent to the lagoon. One of the potential possibilities to limit the flood risk is to decrease the water level in the...
-
Local buckling of composite channel columns
PublicationThe investigation concerns local buckling of compressed flanges of axially compressed composite channel columns. Cooperation of the member flange and web is taken into account here. The buckling mode of the member flange is defined by rotation angle a flange about the line of its connection with the web. The channel column under investigation is made of unidirectional fibre-reinforced laminate. Two approaches to member orthotropic...
-
Refinement of the Hardening Soil model within the small strain range
PublicationThe popularity of the elasto-plastic Hardening Soil (HS) model is based on simple parameter identification from standard testing and empirical formulas. The HS model is implemented in many commercial FE codes designed to analyse geotechnical problems. In its basic version, the stress–strain behaviour within the elastic range is subject to the hypoelastic power law, which assures the barotropy of the elastic stiffness. However,...
-
Modelling and Analysis of the Positioning Accuracy in the Loading Systems of Mobile Cranes
PublicationIn this work, the authors analyse the influence of the order and range of sequential movements of a crane's working members on the accuracy of the final cargo positioning. The analysis was conducted on the basis of a specially developed method in which the authors proposed the introduction of a geometrical indicator of positioning the load in the intermediate positions (after completing each movement sequence) and in the target...
-
Dynamic analysis of the railway bridge span under moving loads
PublicationThe first part of this paper provides a review of the state of knowledge of the dynamic behaviour of railway bridges under moving loads. Particular attention is paid to developments in modelling railway bridge loading and dynamic vehicle-span (structure) interaction. The most important aspects determining the advancements in this area of knowledge are identified. The contemporary techniques for defining bridge span finite element...
-
Damage-involved response of two colliding buildings under non-uniform earthquake loading
PublicationPounding between insufficiently separated buildings, which may result in considerable damage or may even lead to the total collapse of colliding structures, has been repeatedly observed during earthquakes. Earthquake-induced collisions of buildings has been intensively studied applying various structural models. It was assumed in the analyses, however, that the seismic excitation is identical for all structural supports; whereas,...
-
Application of the Bodner-Partom constitutive equations for modelling of the technical fabric Valmex used for the hanging roof of the Forest Opera in Sopot
PublicationThe study of an inelastic properties of the technical fabric Valmex used for 20 years as the roof structure of the Forest Opera in Sopot (Poland) is presented. The uniaxial tensile laboratory tests with constant strain rate have been conducted and analysed. Parameters of the Bodner-Partom constitutive model have been identified and verified by numerical simulations. Two approaches of the parameters identification have been proposed:...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublicationThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
An attempt to develop a model selection algorithm of computer simulation during the design process of mechanical response of any mechanical body
Publicationn the literature, there are algorithms associated with the design of simulations of technological processes, in which the material model has always been defined previously. However, in none of the studies of computer simulation modelling of technological processes known to the authors of this article, is there a detailed description of how the algorithm, or the selection of plastic model used, is subject to this process. This article...
-
A new viscoelastic method of calculation of low-temperature thermal stresses in asphalt layers of pavements
PublicationThe paper presents a new method of calculation of thermal stresses in asphalt layers of pavements induced by cooling or heating. The method, developed by the author, is based on the analytical solution for the linear viscoelastic Burgers model extended numerically for the case of asphalt layers whose rheological parameters are strongly dependent on temperature. The coefficient of thermal expansion and Poisson’s ratio may optionally...
-
An Attempt to Develop a Model Selection Algorithm of Computer Simulation during the Design Process of Mechanical Response of Any Mechanical Body
PublicationIn the literature, there are algorithms associated with the design of simulations of technological processes, in which the material model has always been defined previously. However, in none of the studies of computer simulation modelling of technological processes known to the authors of this article, is there a detailed description of how the algorithm, or the selection of plastic model used, is subject to this process. This...
-
Estimation of Failure Initiation in Laminated Composites by means of Nonlinear Six-Field Shell Theory and FEM
PublicationThe monography deals with the problem of failure initiation in thin laminated composites. Known techniques of laminate structures modelling are briefly characterised. Eventually, shell based approach is chosen for the purpose of the description of the composite structures behaviour, as it predicts their deformation and states of stress effectively in a global sense. The nonlinear six parameter shell theory (6p theory) with asymmetric...
-
FEM analysis of composite materials failure in nonlinear six field shell theory
PublicationThe monography deals with the problem of failure initiation in thin laminated composites. Known techniques of laminate structures modelling are briefly characterised. Eventually, shell based approach is chosen for the purpose of the description of the composite structures behaviour, as it predicts their deformation and states of stress effectively in a global sense. The nonlinear six parameter shell theory (6p theory) with asymmetric...
-
MODELLING OF CONCRETE FRACTURE AT AGGREGATE LEVEL USING DEM BASED ON X-RAY mu CT IMAGES OF INTERNAL STRUCTURE
PublicationThe paper describes two-dimensional meso-scale numerical results of fracture in notched concrete beams under quasi-static three-point bending. Concrete was modelled as a random heterogeneous 4-phase material composed of aggregate particles, cement matrix, interfacial transitional zones (ITZs) and air voids. As a numerical approach, the discrete element method (DEM) was used. The concrete micro-structure in calculations was directly...
-
OCENA NOŚNOŚCI STAREGO MOSTU ŁUKOWEGO W JAGODNIKU
PublicationArtykuł opisuje przeprowadzoną analizę statyczno-wytrzymałościowa 95-letniego betonowego mostu łukowego zlokalizowanego w Jagodniku w północnej Polsce. Trwałość i wytrzymałość starego betonu są określane na podstawie wybranych właściwości mechanicznych, fizycznych i chemicznych. Program badań laboratoryjnych składał się z następującego zestawu badań: pomiary głębokości strefy skarbonatyzowanej i gęstości w stanie suchym, badania...
-
Modelling of shear zones during quasi-static granular silo flow using material point method (MPM)
PublicationThe paper focuses on confined silo flow of cohesionless sand. The problem considered is a quasi-static flow in a plane strain model silo with parallel walls simulated with the material point method (MPM). The simulation used a non-local hypoplastic constitutive model. Initially, the paper validated the implemented numerical approach with basic element tests and a plane strain compression test. The subsequent MPM calculations for...
-
Nutrient transport and acquisition by diatom chains in a moving fluid
PublicationThe role of fluid motion in delivery of nutrients to phytoplankton cells is a fundamental question in biological and chemical oceanography. In the study of mass transfer to phytoplankton, diatoms are of particular interest. They are non-motile, are often the most abundant components in aggregates and often form chains, so they are the ones expected to benefit most from enhancement of nutrient flux due to dissipating turbulence....
-
Influence of soil anisotropic stiffness on the deformation induced by an open pit excavation.
PublicationIn this paper, the problem of deformation induced by an open pit excavation in anisotropic stiff soils is analysed by FE modelling. The presented research is focused on the influence of material model with anisotropic stiffness on the accuracy of deformation predictions as compared with the field measurements. A new hyperelastic-plastic model is applied to simulate anisotropic mechanical behaviour of stiff soils. It is capable...
-
On the theory and numerical simulation of acoustic and heat modes interaction in a liquid with bubbles: acoustic quasi-solitons
PublicationTeoria rzutowania zaburzenia ogólnego na mody. Zastosowanie metody do badań układu równań typu Korteweg`a-de Vries`a. Rozwiązania analityczne i simulacje numeryczne.
-
Lessons learned during SRAD hybrid motor development
PublicationStudent Researched and Developed (SRAD) hybrid rocket motor H-15 with total impulse of 15 $kNs$ was built. First version of the engine has average thrust of 3 $kN$, the second, improved one is prepared with an aim to have average thrust of 5 $kN$. Engine development was started from scratch and went through phases of: definition of design assumptions and constraints, numerical modelling to predict engine performance, CAD and CAM...
-
Proportional-Derivative and Model-Based Controllers for Control of a Variable Mass Manipulator
PublicationIn the paper, numerical analysis of dynamics of a variable mass manipulator is presented. A revolute joints composed manipulator is considered. Payload of the gripper is considered as the only element characterized by unknown value of its mass (variable between subsequent operations). As in other cases of the revolute joints composed manipulators, its behaviour dependents significantly on the pose of the manipulator. When the manipulator...
-
Modelling of in-plane wave propagation in a plate using spectral element method and Kane-Mindlin theory with application to damage detection
PublicationThis paper presents results of experimental and numerical analyses of in-plane waves propagatingin a 5 mm-thick steel plate in the frequency range of 120-300 kHz. For such a thickness/frequency ratio,extensional waves reveal dispersive character. To model in-plane wave propagation taking into account thethickness-stretch effect, a novel 2D spectral element, based on the Kane-Mindlin theory, was formulated. Anapplication of in-plane...
-
The fracture behaviour of notched PMMA specimens under simple loading conditions – Tension and torsion experimental tests
PublicationThis paper presents the results of experimental testing of flat PMMA specimens during uniaxial loading conditions. Two separate tests were conducted: tensile and torsion. The specimens were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. The specimens were made in two thickness variants: 5 and 15 mm. Monotonic tensile and torsion tests were carried out while keeping the averaged strain rate constant,...
-
Novel analysis methods of dynamic properties for vehicle pantographs
PublicationTransmission of electrical energy from a catenary system to traction units must be safe and reliable especially for high speed trains. Modern pantographs have to meet these requirements. Pantographs are subjected to several forces acting on their structural elements. These forces come from pantograph drive, inertia forces, aerodynamic effects, vibration of traction units etc. Modern approach to static and dynamic analysis should...
-
Modelowanie kratownicy z kształtowników giętych na zimno z mimośrodami dodatnimi w węźle = Modelling of truss with cold-formed section and positive eccentricyty in the node.
PublicationThe topic of this research is establishing load-carrying capacity of compressed and tensed chords of trusses made of cold-formed open cross-sections. Occurrence of bending in the truss’ chord is the result of specific production technology assumed by the designer and producer of lattice girder’s systems. The aim of this research is to present methodology of conduct while creating numerical models that best depict the behaviour...
-
Electromagnetic-based derivation of fractional-order circuit theory
PublicationIn this paper, foundations of the fractional-order circuit theory are revisited. Although many papers have been devoted to fractional-order modelling of electrical circuits, there are relatively few foundations for such an approach. Therefore, we derive fractional-order lumped-element equations for capacitors, inductors and resistors, as well as Kirchhoff’s voltage and current laws using quasi-static approximations of fractional-order...
-
Modelling of laminated glass PVB walls of buildings exposed to vehicle impact with different speeds
PublicationThis paper presents an analytical model, developed for laminated glass subjected to a low-velocity impact. It has the ability to capture glass cracks as well as large non-linear deformations. It is based mathematically on the firstorder deformation concept, which considers the effect of membrane and transverse shear as well as bending. This theory uses damage mechanics to capture the glass cracking. For this purpose, several experiments...
-
Investigations of the Working Process in a Dual-Fuel Low-Emission Combustion Chamber for an FPSO Gas Turbine Engine
PublicationThis investigation is devoted to an analysis of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. The low-emission gas turbine combustion chamber with partial pre-mixing of fuel and air inside the outer and inner radial-axial swirlers was chosen as the object of research. When modelling processes in a dual-flow low-emission gas turbine combustion chamber, a generalized method...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART IV) MODELLING THE HEATING PROCESS AND DETERMINING THE SERVICEABILITY OF HYDRAULIC COMPONENTS DURING THE STARTING-UP IN LOW AMBIENT TEMPERATURE
PublicationDesigners of hydraulically driven machines and devices are obliged to ensure during design process their high service life with taking into account their operational conditions. Some of the machines may be started in low ambient temperature and even in thermal shock conditions (due to delivering hot working medium to cold components). In order to put such devices into operation appropriate investigations, including experimental...
-
Proportional-Derivative and Model-based Controllers used for a Serial Type Manipulator in case of a Variable Mass Payload
PublicationIn the paper, numerical analysis of dynamics of a variable mass system is considered. Its reference example is a serial-like manipulator composed of revolute joints and rigid bodies. Payload of its gripper is considered as its variable mass element (mass and inertia irregularly between subsequent payloads). For the rest of the system, inertia parameters are considered as known (precisely identified during the assembling process)....
-
Modelling hydraulic and capillary-driven two-phase fluid flow in unsaturated concretes at the meso-scale with a unique coupled DEM-CFD technique
PublicationThe goal of the research was to demonstrate the impact of thin porous interfacial transition zones (ITZs) between aggregates and cement matrix on fluid flow in unsaturated concrete caused by hydraulic/capillary pressure. To demonstrate this impact, a novel coupled approach to simulate the two-phase (water and moist air) flow of hydraulically and capillary-driven fluid in unsaturated concrete was developed. By merging the discrete...
-
Simplified Distribution Grid Modelling for Connection Analyses
PublicationThis paper considers the modelling of medium and low voltage grids for the purpose of connection studies by distribution grid operators. Possible simplifications in grid modelling are discussed, which are acceptable from the viewpoint of the final result. The main driver of the modelling simplification is the MS Excel environment used as the computation platform, and the limitation of time for grid modelling.
-
PHYSICAL MODELLING OF GEOTECHNICAL STRUCTURES IN PORTS AND OFFSHORE
PublicationThe physical modelling of subsoil behaviour and soil-structure interaction is essential for the proper design of offshore structures and port infrastructure. A brief introduction to such modelling of geoengineering problems is presented and some methods and experimental devices are described. The relationships between modelling scales are given. Some examples of penetration testing results in centrifuge and calibration chamber...