Filters
total: 3336
filtered: 2514
displaying 1000 best results Help
Search results for: LOAD, MEASURING STANDARD
-
Electrical and mechanical characterization of two-phase alloys by means of scanning probe microscopy in dynamic impedance spectroscopy mode
PublicationDynamic impedance spectroscopy, evaluated for measuring non-stationary systems, was used in combination with scanning probe microscope. Using this approach, localized impedance measurements in the AFM contact mode could be carried out. Additionally, impedance–force curves were made at each phase of investigated materials to illustrate the relation between impedance and the force applied to a probe. Therefore, correlation of electrical...
-
Design of microstrip antenna subarrays: a simulation-driven surrogate-based approach
PublicationA methodology for computationally efficient simulation-driven design of microstrip antenna subarrays is presented. Our approach takes into account the effect of the feed (here, a corporate network) on the subarray side-lobe level and allows adjustment of both radiation and reflection responses of the structure under design within a single automated process. This process is realized as surrogate-based optimization that produces...
-
Simulation-Driven Design of Microstrip Antenna Subarrays
PublicationA methodology for computationally efficient simulation-driven design of microstrip antenna subarrays is presented. Our approach takes into account the effect of the feed (e.g., a corporate network) on the subarray side lobe level and allows adjusting both radiation and reflection responses of the structure under design within a single automated process. This process is realized as surrogate-based optimization that produces designs...
-
Application of acoustic emission for detection of fatigue microdemage in main and crank bearings for diesel engines
PublicationThe article presents reasons for applying the acoustic emission (AE) to detect fatigue microdamage in main bearings and crank bearings of ship main engines. Problem of determination of the fatigue life for slide bearing bushes was characterized in general. There were demonstrated properties of the objects of research, which were bushings made of the MB58 alloy, as well as an overall description of the research. It was shown that...
-
LOW COST MEASUREMENT MODULE FOR MATRIX OF AMPEROMETRIC GAS SENSOR
PublicationThis paper describes an amperometric sensor module for gas concentration measurement. A module can be used for many types of electrochemical gas sensors without major hardware changes. Device is based on AVR ATmega8 microcontroller. As signal processing circuit a specialized integrated circuit LMP9l000 configurable via I2C interface is used. The concept of a measuring system composed of several modules dedicated for a gas sensors...
-
Impact of probability distribution on the uncertainty of resistance measurement
PublicationThe paper presents studies on the influence of probability distributions on the expanded uncertainty of the resistance measurement. Choosing the correct probability distribution is very important to estimate of measurement uncertainty. The paper presents the results of analysis of the resistance measurement uncertainty using the technical method of resistance: 100 G. The analysis of the uncertainty...
-
Correction of determined coordinates of railway tracks in mobile satellite measurements
PublicationThis article examines one of the basic issues related to the technique of mobile satellite measurements in railway tracks. This problem concerns the correction of the determined coordinates of the track centerline. The need to perform this operation results from the GNSS receivers positioning at a certain height above the level of the existing track axis, leading to longitudinal and lateral shifts of antennas. The key problem here...
-
Displacement measurements during load testing of railway arch bridge
PublicationThe paper discusses issues concerning load tests carried out on a twin-track, arch railway bridge over the Martwa Wisla river in Gdansk. Currently, it is the bridge with the longest span in its class in Poland. The load-bearing structure consists of three no-hinge arches and an orthotropic deck suspended from them. The studies of the structure assumed the performing of static and dynamic tests. The paper presents the method for...
-
Correlation between natural frequencies and buckling load in a stiffened shell
PublicationThe paper deals with correlation between natural frequencies and buckling load of a stiffened shell composed of corrugated sheets and vertical stiffeners (columns). The simplified shell segment represents the buckling behaviour of a whole silo with sparsely distributed columns. The paper covers variants of linear buckling anal-yses, dynamic eigenvalue analyses and geometrically non-linear analyses of a segment modelled with shell...
-
Statistical properties of a modified standard map in quantum and classical regimes
PublicationWe present a model—a modified standard map. This model has interesting properties that allow quantum–classical correspondences to be studied. For some range of parameters in the classical phase space of this model, there exist large accelerator modes. We can create a family of maps that have large accelerator modes.
-
Retrievable strain measuring system in screw displacement piles - readings and results interpretation problems
PublicationStatic load tests on foundation piles are generally carried out in order to determine load – displacement characteristic of the pile. For more detailed information, e.g. force distribution along the shaft, load transfer mechanism and characteristics of soil-structure interaction (unit resistance curves t-z, q-z) additional pile instrumentation is required. Most popular techniques focus on direct concrete strain measurements and...
-
The Taxonomy Spatial Measure of Development in the Standard of Living Analysis
PublicationIncorporation of spatial relationships in the construction of taxonomy measure of development is gaining popularity in Polish literature. However, there is no one common idea concerning how the spatial relationship should be taken into account when creating a synthetic variable nor, indeed, where the spatial weight matrix should be placed. It seems that the inclusion of spatial relationships is more important in smaller regions’...
-
Heuristic scheduling algorithms for uniform load of computer system
PublicationW pracy zaprezentowano opracowany heurystyczny algorytm szeregowania zadań UNILO (ang. UNIform LOad - jednakowe obciążenie), umożliwiający redukcję całkowitego zapotrzebowania na moc obliczeniową systemu komputerowego bez pogarszania jego wydajności. Algorytm ten realizuje takie przydzielenie zadań obliczeniowych do poszczególnych jednostek (procesorów), aby zapewnić ich jednakowe obciążenie. Opracowany algorytm został zweryfikowany...
-
The Influence of External Load on the Performance of Microbial Fuel Cells
PublicationIn this work, the effect of the external load on the current and power generation, as well as on the pollutant removal by microbial fuel cells (MFCs), has been studied by step-wise modifying the external load. The load changes included a direct scan, in which the external resistance was increased from 120 Ω to 3300 Ω, and a subsequent reverse scan, in which the external resistance was decreased back to 120 Ω. The reduction in the...
-
Performance Analysis of the "Intelligent" Kirchhoff- Law - Johnson-Noise Secure Key Exchange
PublicationThe Kirchhoff-law - Johnson-noise (KLJN) secure key distribution system provides a way of exchanging theoretically secure keys by measuring random voltage and current through the wire connecting two different resistors at Alice’s and Bob’s ends. Recently new advanced protocols for the KLJN method have been proposed with enhanced performance. In this paper, we analyze the KLJN system and compare with the „intelligent” KLJN (iKLJN)...
-
Potentiometric Solid-Contact Multisensor System for Simultaneous Measurement of Several Ions
PublicationThe design and performance of potentiometric multisensor system made in solid-contact technology is described. Both, the measuring electrodes as well as the reference electrode are in a compact cell. The system allows for simultaneous measurement of various ions. The characteristics of the electrodes for Na+, K+ and Ca2+ ions were determined using the designed system and compared with ISEs of the same membrane composition in classical...
-
Parallel Computations of Text Similarities for Categorization Task
PublicationIn this chapter we describe the approach to parallel implementation of similarities in high dimensional spaces. The similarities computation have been used for textual data categorization. A test datasets we create from Wikipedia articles that with their hyper references formed a graph used in our experiments. The similarities based on Euclidean distance and Cosine measure have been used to process the data using k-means algorithm....
-
A spice equivalent circuit for modeling the performance of dual frequency echo-sounder
PublicationThe paper presents novel network equivalent circuit of piezoceramic circular disc transducers that takes into account thickness and radial mode of vibrations. The starting point of the analysis is 4-port description of circular disc element representing the solution of wave equation set in radial and thickness directions. The approximate solution for harmonic case is represented in the form of 4x4 matrix, which is synthesised and...
-
Evaluation of the structures size in the liquid-gas flow by gamma-ray absorption
PublicationThe rapid development of tomography methods particularly electrical, X and gamma rays allows for a wide range of the information about flow structure. However, all of such methods are quite complicated. At the same time much simpler systems as the measuring system of gamma rays absorption, allows to obtain a all key flow information which describe the two-phase flow. In the article the results of analyzes of radiometric signal...
-
Criteria for assessment of pine wood surfaces after planing
PublicationThe arise of defects in raw material as well as a machined part in most cases causes need to qualify the final product (wooden frames) as a scrap part or an additional work activity must be done. In the paper selected results of the effect of the material defects on the surface quality of the elements after planing and painting are presented. The materials under production were glulam elements of pine wood. Research experiments...
-
Risk Analysis by a Probabilistic Model of the Measurement Process
PublicationThe aim of the article is presentation of the testing methodology and results of examination the probabilistic model of the measurement process. The case study concerns the determination of the risk of an incorrect decision in the assessment of the compliance of products by measurement. Measurand is characterized by the generalized Rayleigh distribution. The model of the meas-urement process was tested in parallel mode by six risk...
-
Blurred quantum Darwinism across quantum reference frames
PublicationQuantum Darwinism describes objectivity of quantum systems via their correlations with their environment--information that hypothetical observers can recover by measuring the environments. However, observations are done with respect to a frame of reference. Here, we take the formalism of [Giacomini, Castro-Ruiz, & Brukner. Nat Commun 10, 494 (2019)], and consider the repercussions on objectivity when changing quantum reference...
-
Standard of living in Poland at regional level - classification with Kohonen self-organizing maps
PublicationThe standard of living is spatially diversified and its analyzes enable shaping regional policy. Therefore, it is crucial to assess the standard of living and to classify regions due to their standard of living, based on a wide set of determinants. The most common research methods are those based on composite indicators, however, they are not ideal. Among the current critiques moved to the use of composite...
-
Biocompatibility and Bioactivity of Load-Bearing Metallic Implants
PublicationThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
Towards Designing an Innovative Industrial Fan: Developing Regression and Neural Models Based on Remote Mass Measurements
PublicationThis article presents the process of the construction and testing a remote, fully autonomous system for measuring the operational parameters of fans. The measurement results obtained made it possible to create and verify mathematical models using linear regression and neural networks. The process was implemented as part of the first stage of an innovative project. The article presents detailed steps of constructing a system to...
-
Determination of equivalent axle load factors with the use of strain energy of distortion
PublicationThe paper proposes a new method for calculation of equivalent axle load factors based on the analysis of strain energy of distortion induced in road pavements by traffic loads. The main advantage of the method is the more accurate calculation of the effects of multiple axles and super single versus dual tyres. The methodconsiders the location of critical points, at which strain energy of distortion reaches extreme values. When...
-
Standard MST i jego wykorzystanie przy opisie jednostek chorobowych
PublicationW podrozdziale przedstawiono ujednolicony sposób opisu chorób gastroentero-logicznych. Omówiono założenia standardu MST oraz model dokumentu elektroni-cznego. Opisano jak zaimplementowano ten standard w systemie ERS i jak natej podstawie utworzono elektroniczny atlas endoskopowy.
-
Static load test on concrete pile – instrumentation and results interpretation
PublicationFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Load testing of a suspended footbridge in Radom (Poland)
PublicationThe footbridge in Radom is a suspended bridge of an interesting architectural form. The structure was de-signed for 4 kN/m2 of crowd loading. Dynamic calculations were not included in the design. The structure’s acceptance tests took place on the 14th of October 2016. The behaviour of the footbridge in static testing met the expectations. Unfortunately, as a result of dynamic tests, dangerous behaviour of the footbridge was revealed....
-
Experimental Study of Dapped-End Beams Subjected to Inclined Load
PublicationThis paper presents the results of an experimental investigation of the reinforced concrete (RC) dapped-end beams loaded with inclined forces, compared to identical ones loaded with vertical forces only. Such a load may occur in, for example, Gerber's joints or in dapped-end beams supported on corbels, where the vertical gravitation force is additionally completed with horizontal forces caused by temperature differences, shrinking,...
-
Influence of sensor design and optical properties of tissue on the photoplethysmographic signal
PublicationPhotopletysmography and an associated technique called pulse oximetry are still explored due to the expectations that they give a lot of information about the state of the patient and, also, due to the fact that they are non invasive. Knowledge about the impact of various parameters on the measured signal leads to a faster and a more reliable way of analyzing measurement results and finding the dependencies between the involved...
-
Experiments and Analysis of the Limit Stresses of a Magnetorheological Fluid
PublicationPaper presents the results of a rheological test of a commercial magnetorheological (MR) fluid (MRF-132DG). The researchincludes the problem of measuring and interpreting limit stresses under conditions close to the magnetic saturation of the fluid. Fourdifferent limit stresses were determined, two related to the yield point and two related to the flow point. Methods for determining limitstresses, especially due to excitation...
-
Disturbances of Earth magnetic field caused by eddy currents of airplane
PublicationThe uniform magnetic field of the Earth in the surrounding of a mobile, metallic object undergoes deformation by eddy currents. The influence of the moving, conducting object on the Earth's total magnetic field depends on the object's shape, position and speed of the changes relative to the magnetic field vector of the Earth, as well as the electric conductivity and the relative magnetic permeability of the material. Disturbances...
-
STUDY OF ARRAY OF MEMS INERTIAL MEASUREMENT UNITS UNDER QUASI-STATIONARY AND DYNAMIC CONDITIONS
PublicationA measurement system includes all components in a chain of hardware and software that leads from a measured variable to processed data. In that context, the type and quality of the sensors or measuring devices are critical to any measurement system. MEMS/IMU sensors lag behind leading technologies in this respect, but the MEMS/IMU performance rapidly changes while is relatively inexpensive. For this reason, the paper proposes...
-
On the influence of a surface roughness on propagation of anti-plane short-length localized waves in a medium with surface coating
PublicationWe discuss the propagation of localized surface waves in the framework of the linear Gurtin–Murdoch surface elasticity and taking into account a roughness of a free boundary. We derive a boundary-value problem for anti-plane motions with curvilinear boundary and surface stresses. Using the asymptotic technique developed earlier, we obtain the form of a localized wave and analyze its amplitude evolution. As the main result we present...
-
Porous Phantoms Mimicking Tissues—Investigation of Optical Parameters Stability Over Time
PublicationOptical phantoms are used to validate optical measurement methods. The stability of their optical parameters over time allows them to be used and stored over long-term periods, while maintaining their optical parameters. The aim of the presented research was to investigate the stability of fabricated porous phantoms, which can be used as a lung phantom in optical system. Measurements were performed in multiple series with an interval...
-
SIMPLY AND LOW COAST ELECTROMYOGRAPHY SIGNAL AMPLIFIER
PublicationRecently, there has been a noticeable increase in interest in solu tions utilizing electrical signals accompanying muscle activity. Electromyography (EMG) is a technique for recording, analysis and evaluating the electrical activity produced by striated muscle. Its great popularity is due, among other, to the ability to measure with non-invasive electrodes (calle d as sEMG surface electromyography)....
-
The effect of an active force while slide diamond burnishing of wooden shafts upon process quality
PublicationThe quality of the surface of wooden elements that have been turned and burnished has got a crucial meaning in the whole production process flow, since the obtained effects affect the quality of the wooden surface after finishing (coating, painting). In the paper, selected results of the investigation of the effect of the burnishing process on the surface quality of the elements after turning are presented. Research experiments...
-
Effect of Impoundment on Physico-chemical Properties of Water in the Flowing through stream, the Case of the Turawa Reservoir
PublicationThe Turawa reservoir is one of the most important storage reservoirs in Poland. Quite many physico-chemical parameters of water in the reservoir itself and also in the Mała Panew, the river flowing through the reservoir were measured at various periods of the year. Measuring and sampling points were situated at the river inflow, over the reservoir, and at the river outflow. The parameters included temperature, electrical conductivity,...
-
Optimal ECG lead for deriving respiratory signal
PublicationEDR is an interesting measuring technique that allows an indirect assessment of respiratory activity. This is an alternative solution to direct methods that are based on the measurement of air flow, which require a specialized sensor or even a system. However, due to inter-personal anatomical differences, the optimal ECG lead (placement of the electrodes) ensuring the best EDR signal quality is not fixed. An influence of ECG lead...
-
Discussion - Experimental study of dapped–end beams subjected to inclined load
PublicationDiscussion - Experimental study of dapped–end beams subjected to inclined load
-
Consideration of dynamic loads in the determination of axle load spectra for pavement design
PublicationAxle load spectra constitute a crucial part of the data for pavement design and pavement distress analysis. Typically, axle load spectra represent static load from vehicles and do not include dynamic loads generated by vehicles in motion. While dynamic loads can significantly contribute to faster pavement distress, this fact is mostly omitted in pavement design methods. The paper presents a methodology for consideration of dynamic...
-
Stability and load bearing capacity of a truss with elastic braces
PublicationThe present paper is devoted to the numerical and experimental investigations of stability of a truss stiffened by elastic braces. The model of a real roof truss scaled by factor ¼ was investigated. In the research the linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity is presented. The initial imperfections were assumed in the form of the first buckling mode....
-
Standard gas mixtures- indispensable reference materials in the analysis of gaseous media
PublicationIn recent years the need for the quality control and assurance of analytical measurement results has been particularly strongly emphasised. Certified reference materials play an invaluable role in this process. The article characterises the basic types of reference materials, focusing in particular on those in the gaseous state. It also reviews the literature on the techniques of preparing standard gas mixtures over the last ten...
-
Standard gas mixtures- indispensable reference materials in the analysis of gaseous media
PublicationIn recent years the need for the quality control and assurance of analytical measurement results has been particularly strongly emphasised. Certified reference materials play an invaluable role in this process. The article characterises the basic types of reference materials, focusing in particular on those in the gaseous state. It also reviews the literature on the techniques of preparing standard gas mixtures over the last ten...
-
Non-matrix reference matrials- chalanges in the preparation of standard gas mixtures
PublicationIn the last few years particularly great pressure is exerted on quality control and assurance of analytical measurement results. An invaluable role in this process is played by reference materials. The paper presents the characteristics of basic types of reference materials, with particular attention to gaseous reference materials. In addition, a review of literature on techniques of preparation of gaseous standard materials, published...
-
2015. Motion analysis of a kitesurfer employing a vision-based measurement system
PublicationAbstract. Kitesurfing is a relatively new phenomenon with rising popularity worldwide – a recently developed extreme watersport considered a high-risk injury sport. It combines elements of several other sports, in particular, sailing, surfing, windsurfing, wakeboarding, and snowboarding. The main purpose of authors’ research in the present paper is to use a vision-based system for measuring a kitesurfer’s body movements in order...
-
Reconstruction of 3D structure of positive corona streamer by local methods
PublicationThe computer algorithms were used for reconstruction of streamer 3D structure. We propose the 3D tree structure model of corona discharge streamer composed with nodes and edges between chosen couples of nodes, which enables easy computation of some important parameters ofstreamers. The 3D model can be derived directly from two projection images by global methods like evolutionary searching or particle simulations. In this paper...
-
EXPERIMENTAL STUDY OF SURFACE ROUGHNESS EFFECT ONTHE RHEOLOGICAL BEHAVIOR OF MR FLUID
PublicationPaper presents the results of shear stress measurements of a commercial magnetorheological fluid using a plate-plate type geometry with a modified working surface. The purpose of the study was to determine the effect of changing the roughness of the measuring plate on the obtained shear stress results. Controlled shear rate tests and Magneto Sweep measurements were carried out for three MR fluid layer heights. The tests were...
-
On modelling and non-linear elasto-plastic analysis of thin shells with deformable junctions
PublicationThe undeformed base surface of the irregular thin shell is modelled by the union of a finite number of regular smooth surface elements joined together along spatial curvilinear surface edges. The equilibrium conditions are formulated by postulating an appropriate form of the principle of virtual work, where also deformability of shell junctions is taken into account. The PVW is then discretised by C1 finite elements and the incremental-iterative...