Filters
total: 6665
filtered: 5382
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: HIGH-SPEED DRIVE
-
Analysis of Positioning Error and Its Impact on High Frequency Performance Parameters of Differential Signal Coupler of Differential Signal Coupler
PublicationThis paper presents the analysis of the effect of differential signal coupler positioning accuracy on its high frequency performance parameters for contact-less high speed chip-to-chip data transmission on PCB application. Our considerations are continuation of the previous works on differential signal coupler concept, design methodology and analysis for high speed data transmission monitoring presented in [1, 2]. The theoretical...
-
Suppression of distortions in signals received from Doppler sensor for vehicle speed measurement
PublicationDoppler sensors are commonly used for movement detection and speed measurement. However, electromagnetic interference and imperfections in sensor construction result in degradation of the signal to noise ratio. As a result, detection of signals reflected from moving objects becomes problematic. The paper proposes an algorithm for reduction of distortions and noise in the signal received from a simple, dual-channel type of a Doppler...
-
Accuracy, Memory and Speed Strategies in GPU-based Finite-Element Matrix-Generation
PublicationThis paper presents strategies on how to optimize GPU-based finite-element matrix-generation that occurs in the finite-element method (FEM) using higher order curvilinear elements. The goal of the optimization is to increase the speed of evaluation and assembly of large finite-element matrices on a single GPU (Graphics Processing Unit) while maintaining the accuracy of numerical integration at the desired level. For this reason,...
-
Experimental study on the selected aspects of bow thruster generated flow field at ship zero-speed conditions
PublicationThe paper presents the results of experimental study on the interaction between the bow thrusters understood as the flow field changes generated by bow tunnel thruster in deep water conditions operated as a single and twin units. The research was limited to zero-speed case for the ship dead in the water. The influence of the hull form and jet spread between the neighbouring thrusters for several combinations of the applied bow...
-
Analysis of different tillage implements with respect to reduced fuel consumption, tractor operating speed and its wheel slippage
PublicationNowadays the prices of agricultural farm produced products are increasing with ant-speed and the prices of input for raising crops are increasing with rocket-speed. Therefore, there is a dire need to conduct some important studies to innovate the techniques which can lower the costs of crop production. In this context, this study was conducted to evaluate the consumption of fuel at different tillage implements, tractor operating...
-
Influence of the Tool Rotational Speed on Physical and Chemical Properties of Dissimilar Friction-Stir-Welded AA5083/AA6060 Joints
PublicationAluminum alloys have been successfully used in the railroad and automotive industries because of their potential to significantly reduce component weights, and their good mechanical and anti-corrosion properties. Problems with joining aluminum alloys are characterized by low weldability, which influences the need for studies focused on unconventional methods. The environmentally friendly and low-cost friction-stir-welding method...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublicationThe paper presents the results of a design analysis of a micro-turbine for a co-generation micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attention was...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublicationThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
HIGH LEVEL SYNTHESIS IN FPGA OF TCS/RNS CONVERTER
PublicationThe work presents the design process of the TCS/RNS (two's complement–to– residue) converter in Xilinx FPGA with the use of HLS approach. This new approach allows for the design of dedicated FPGA circuits using high level languages such as C++ language. Such approach replaces, to some extent, much more tedious design with VHDL or Verilog and facilitates the design process. The algorithm realized by the given hardware circuit is...
-
High Frequency Conducted Emission in AC Motor Drives Fed By Frequency Converters: Sources and Propagation Paths
PublicationProvides a concise and thorough reference for designing electrical and electronic systems that employ adjustable speed drives Electrical and electronic systems that employ adjustable speed drives are being increasingly used in present-day automation applications. They are considered by many application engineers as one of the most interfering components, especially in a contemporarily faced industrial environment. This book fills...
-
Adaptive traffic optimization using Variable Speed Limits; Adaptacyjna optymalizacja ruchu drogowego przy pomocy zmiennych ograniczeń prędkości
PublicationVariable speed limits (VSL) is an intelligent transportation system (ITS) solution for traffic management. The speed limits can be changed dynamically in order to adapt to traffic, weather, or road surface conditions. This paper presents an approach for such an adaptive traffic control where the primary goal is to ensure traffic safety and efficiency of the traffic control system (fast response to dynamically changing traffic,...
-
Influence of High Temperature Oxidation on Hydrogen Absorption and Degradation of Zircaloy-2 and Zr 700 Alloys
PublicationThe present research was aimed at determining the effects of the oxide layers on hydrogen absorption, microstructure and mechanical properties of the Zircaloy- 2 and Zr 702 alloys. The oxidation was made at 350 °C, 700 °C and 900 °C for 10 to 30 min in laboratory air, followed by hydrogen cathodic charging for 72 h and annealing at 400 °C for 4 h. The slow strain rate tests were carried out on oxidized, charged and annealed specimens. The...
-
Optimization of the spindle speed during milling of large-sized structures with the use of technique of Experiment-Aided Virtual Prototyping
PublicationIn the paper are presented considerations concerning vibration suppression problems during milling of large-sized workpieces with the use of innovative method of matching the spindle speed of cutting tool. It depends on repeatable change of the spindle speed value as soon as the optimal vibration state of the workpiece approaches. The values of dominant “peaks” in the frequency spectra and the Root Mean Square (RMS) values of time...
-
Frequency characteristics of induction machine speed observers
PublicationWłaściwości napędu bezczujnikowego z silnikiem indukcyjnym zależą od struktury obserwatora prędkości. System ten wymaga starannej analizy w przypadku uszkodzenia maszyny, której celem jest odpowiedź na pytania: jak układ regulacji pracuje przy niesymetrii maszyny spowodowanej np. uszkodzeniem klatki wirnika oraz jak obserwator odtwarza pulsacje prędkości spowodowane niesymetrią maszyny. W artykule przedstawiono charakterystyki...
-
Changes in the speed of ants as a result of aggressive interactions
Publication -
Assessment of the Speed Management Impact on Road Traffic Safety on the Sections of Motorways and Expressways Using Simulation Methods
PublicationMethods used to evaluate the impact of Intelligent Transport System (ITS) services on road safety are usually based on expert assessments or statistical studies. However, commonly used methods are challenging to apply in the planning process of ITS services. This paper presents the methodology of research using surrogate safety measures calculated and calibrated with the use of simulation techniques and a driving simulator. This...
-
MRAS-Based Switching Linear Feedback Strategy for Sensorless Speed Control of Induction Motor Drives
PublicationThis paper presents a newly designed switching linear feedback structure of sliding mode control (SLF-SMC) plugged with an model reference adaptive system (MRAS) based sensorless fieldoriented control (SFOC) for induction motor (IM). Indeed, the performance of the MRAS depends mainly on the operating point and the parametric variation of the IM. Hence, the sliding mode control (SMC) could be considered a good control alternative...
-
New components for hydraulic drive systems and their performance in thermal shock conditions
PublicationArtykuł prezentuje konstrukcję pomp z rozrządem krzywkowym typu PWK o zmiennej wydajności wraz ze wstępnymi wynikami badań prototypu PWKZ-78. Przedstawiono także wstępne wyniki analiz MES i CFD zjawisk zachodzących w pracującej pompie. W drugiej części zaprezentowano metodykę badań zachowania się pomp w warunkach szokutermicznego i wyniki uzyskane dla pompy typu PWK.
-
Importance of ventilation in modulating interaction between sympathetic drive and cardiovascular variability
Publication -
Energy-Saving Inertial Drive for Dual-Frequency Excitation of Vibrating Machines
Publication -
Dynamical processes in a multi-motor gear drive of heavy slabbing mill
Publication -
Automatic control systems for ships fitted with podded propulsion drive (POD).
PublicationW artykule ukazano celowość i możliwości automatyzacji układów napędowych, zwłaszcza typu POD, przewidzianych do zastosowania na projektowanych w ramach projektu Eureka BALTECOLOGICAL SHIP czterech statkach bałtyckich: kontenerowca, pojazdowa i tankowca oraz statku rzeczno - morskiego. Zawarte w artykule informacje ułatwiają dokonanie wyboru właściwych założeń projektowanego układu sterowania napędem wymienionych wyżej statków.
-
Theoretical models of the torque of mechanical losses in the pump used in a hydrostatic drive
PublicationPrzedstawiono modele teoretyczne i matematyczne momentu strat mechanicznych występujących w pompie o stałej teoretycznej wydajności qPt na obrót wału (o stałej teoretycznej objętości roboczej VPt) bądź o zmiennej geometrycznej wydajności qPgv na obrót wału (o zmiennej geometrycznej objętości roboczej VPgv). Modele mają służyć badaniom laboratoryjnym i symulacyjnym strat energetycznych w pompie umożliwiającym ocenę sprawności energetycznej...
-
Analysis of the possibilities of using of DME fuel in motor boat drive systems
PublicationThe characteristics of alternative fuel for diesel: dimethyl ether (DME) and an analysis of the potential to reduce emissions of toxic compounds by the engines when running on this fuel have been presented in this work. Basic types of design solutions of gas supply and control systems, possible for use in internal combustion engines with DME supply have been also presented. The paper presents a study of the legislation and an analysis...
-
Augmented speed control scheme of dual induction motors with mutual flux angle control loop
PublicationThis paper proposes an augmented speed control scheme of dual induction motors fed by a five-leg voltage source inverter (VSI) with a common/shared-leg. An additional control loop is proposed here and based on the mutual flux angle – the difference between flux angular positions of the IMs. The main purpose of this research is to minimize the energy losses in the common inverter leg by controlling the mutual flux angle, at equal...
-
Intelligent microbearing project with memory of stress-strain history
PublicationTaking into account the increasing need of intelligent micro-bearing with memory, this paper presents the optimization, simulation and practical application of operating parameters(load carrying capacity, friction forces, friction coefficient, wear), simulation for hydrodynamic HDD micro-bearing with curvilinear nano-grooved journal profile. One of the reason of such journal profile is that this journal profile contributes to the...
-
Calculations of notch stress factor of a thin-walled spreader bracket fillet weld with the use of a local stress approach
PublicationPresence of geometric notches in welded joints causes concentration of strains and stresses, therefore reducing fatigue strength of such joints. This article presents an analysis of stress concentrations in a fillet weld of a spreader mounting bracket on a small sailing yacht. The aim of this article is to direct the attention of designers, manufacturers and regulatory bodies to issues of fatigue cracks that form in brackets fastening...
-
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublicationConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
Analysis of energy efficiency of suburban railway transport network
PublicationRising numbers of agglomeration residents cause increased need for people movement on daily basis. Because of congestion of local roads, air pollution and limited parking space, providing mass transit based on electric traction is reasonable. While the electric rail vehicles are considered highly efficient in themselves, they need to be analyzed as a part of a transport network, because energy consumption depends on operating conditions...
-
Sustainable development model for measuring and managing sustainability in the automotive sector
PublicationA growing number of organizations across a variety of industries are now pursuing sustainable management business goals to improve business efficiency, manage stakeholder expectations, or for legislative compliance. This is also the case for automotive manufacturing organizations who are under pressure from their stakeholders to manage and improve sustainability performance. This requires the development of credible measurement...
-
Network effects—do they matter for digital technologies diffusion?
PublicationPurpose The main research target of this paper is to capture the network effects using the case of mobile cellular telephony, identified in European telecommunication markets, and its determinants enhancing the process of digital technologies diffusion. Design/methodology/approach This research relies on panel and dynamic panel regression analysis. The empirical sample covers 30 European countries, and the period for the analysis...
-
Effect of pH and high pressure at sub-zero temperature on the viability of some bacteria
PublicationCelem badań było określenie przeżywalności Escherichia coli i Staphylococcus aureus zawieszonych w soku jabłkowym (pH 3,8) po działaniu ciśnienia 193MPa w temperaturze -20°C. Stwierdzono, że bezpośrednio po działaniu ciśnienia przeżywalność badanych szczepów bakterii nie zmieniała się znacząco. Jednakże liczba komórek zmniejszała się z czasem przechowywania ciśnieniowanych prób. Żywe komórki mikroorganizmów nie były wykrywane w...
-
An Experimentally Aided Operational Virtual Prototyping to Obtain the Best Spindle Speed during Face Milling of Large-Size Structures
PublicationAbstract: The paper presents an original method concerning the problem of vibration reduction in the general case while milling large-size and geometrically complex details with the use of an innovative approach to the selection of spindle speed. A computational model is obtained by applying the so-called operational approach to identify the parameters of the workpiece modal model. Thanks to the experimental modal analysis results,...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublicationThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
Oddziaływania taboru na mosty kolejowe przy zmiennych parametrach ruchu
PublicationW pracy poruszono zagadnienia związane z identyfikacją oraz modelowaniem układu dynamicznego most-pojazd ruchomy. Za element szczególnie istotny uznano czynnik obciążający. Opracowano i wdrożono metodykę identyfikacji cech dynamicznych rzeczywistego pojazdu szynowego. Eksperyment badawczy przeprowadzono dla jednostki trakcyjnej EN57, jednak nie ma żadnych ograniczeń w stosowaniu metody dla innego, konwencjonalnego taboru szynowego....
-
Speed monitoring and management in national road safety program
PublicationW referacie przedstawiono system długoterminowych badań prędkości pojazdów umozliwiający śledzenie ich zmian. Zmiany te są analizowane w powiązaniu z wdrażanymi środkami nadzoru oraz edukacyjnymi oddziaływaniami na uczestników ruchu, a także ze zmianami infrastruktury drogowej. Podano też ogólne zalecenia do programu GAMBIT 2005, wynikające z dotychczasowych badań prędkości.
-
Sensorless multiscalar controls of induction motor at low speed
PublicationW artykule przedstawiono zastosowanie obserwatora prędkości w dwóch różnych układach sterowania multiskalarnego silnikiem klatkowym. Pierwszy układ bazuje na prądzie stojana i strumieniu wirnika, natomiast drugi nowy układ wykorzystuje zmienne prąd stojana i strumień stojana. Zamieszczono wyniki badań symulacyjnych i eksperymentalych w układzie ze sterowaniem na procesorze SHARC.
-
The spindle speed optimal control in modern milling operations.
PublicationPraca dotyczy modeli obrabiarek ze sprzężeniem zwrotnym, w przypadku których istotne znaczenie mają drgania samowzbudne typu chatter. Opis układu drgającego przedstawiono w postaci dynamiki układu sterowanego, przy czym sygnałem sterującym jest chwilowa zmiana prędkości obrotowej wrzeciona. Rozważano frezowanie czołowe smukłym frezem trzpieniowym na pionowym cent rum frezarskim. Przedstawiono rezultaty przykładów symulacji komputerowych....
-
Programmed control of the spindle speed in modern milling machines.
PublicationW pracy przedstawiono nowe podejście do nadzorowania drgań wirujących narzędzi we współczesnych frezarkach. Polega ono na sterowaniu programowym w układach niestacjonarnych. Dotyczy to zamkniętych układów obrabiarek, kiedy to istotną rolę odgrywają drgania samowzbudne typu chatter. Sygnałem sterującym jest chwilowa zmiana prędkości obrotowej. Rozważano frezowanie czołowe smukłym frezem trzpieniowym na pionowym centrum frezarskim....
-
Simple observer for induction motor speed sensorless control
PublicationPrzedstawiono układ sterowania polowo zorientowanego silnikiem asynchronicznym klatkowym pozwalający na pracę w szerokim zakresie prędkości obrotowych bez użycia czujnika prędkości. Zaproponowano estymator zmiennych o prostej strukturze charakteryzujący się znaczna odpornością na zmiany parametrów silnika. Zależności obserwatora oparte są na równaniach obwodu napięciowego silnika. Pokazano wyniki badań eksperymentalnych.
-
A Novel Speed Observer for Doubly-Fed Induction Generator
PublicationThe purpose of this paper is to show a new state observer for doubly-fed generator. A proposed z-type observer algorithm based on mathematical model of doubly fed generator with additional variables treated as a disturbances has been used. A nonlinear multiscalar control method has been used to control active and reactive power of the generator. All analyses were verified by simulations and experiments tests.
-
Increases in leptin levels, sympathetic drive, and weight gain in obstructive sleep apnea
Publication -
Application of renewable energy sources to drive organic Rankine cycle micro CHP
PublicationOdnawialne źródła energii rzadko znajdują zastosowanie przy stawianych obecnie wymaganiach przez nowoczesne ciepłownie. Pojawiła się unikalna okazja pomocy przy wprowadzeniu na rynek elektrowni zoptymalizowanej dla tych nieużywanych i pomijanych źródeł ciepła. Organiczny obieg Rankine'a jest podobny do konwencjonalnych turbin parowych, wyjątkiem jest płyn napędzający turbinę, którym jest płyn roboczy o dużej masie cząsteczkowej....
-
Transient torsional vibrations control in the geared drive trains of the hot rolling mills
Publication -
Analytical model of torsional vibrations of typical sawing machine main drive system
PublicationPrzedstawiono model fizyczny i matematyczny drgań skrętnych napędu głównego typowej pilarki tarczowej. Model tworzą elementy sztywne SES połączone między sobą za pośrednictwem elementów sprężysto - tłumiących EST w układzie szeregowym. W modelu matematycznym uwzględniono: właściwości dynamiczne silnika napędowego, wymiary piły tarczowej, cechy materiału obrabianego (wymiary, rodzaj drewna, wilgotność drewna) oraz właściwości dynamiczne...
-
Analysis of Interspike-Intervals for the General Class of Integrate-and-Fire Models with Periodic Drive
PublicationWe study one-dimensional integrate-and-fire models of the general type x˙=F (t, x) and analyze properties of the firing map which iterations recover consecutive spike timings. We impose very week constraints for the regularity of the function F (t, x), e.g. often it suffices to assume that F is continuous. If additionally F is periodic in t, using mathematical study of the displacement sequence of an orientation preserving circle...
-
Mathematical Modelling of Drive System with an Elastic Coupling Based on Formal Analogy between the Transmission Shaft and the Electric Transmission Line
PublicationIn the paper, the kinematic structure of the transmission shaft between the driving motor and the working mechanism is studied. The analysis is based on electrical and mechanical similarities. The equivalent circuits, typical for electrical systems, are defined for the transmission shaft concerned. Modelling of the transmission shaft based on a formal analogy between the transmission shaft and the electric transmission line is...
-
Core loss resistance impact on sensorless speed control of an induction motor using hybrid adaptive sliding mode observer
PublicationInduction motors (IMs) experience power losses when a portion of the input power is converted to heat instead of driving the load. The combined effect of copper losses, core losses, and mechanical losses results in IM power losses. Unfortunately, the core losses in the motor, which have a considerable impact on its energy efficiency, are not taken into account by the generally employed dynamic model in the majority of the studies. Due...
-
Weldability of high strength steel in underwater environment
PublicationThe article describes the problems with weldability of high-strength steels in the aquatic environment. The tendency of steel S355J2G3 and S500M to form cold cracks when welded in wet welding conditions has been experimentally evaluated. It was found that the tested steels have a high propensity to cracking. An experiment has been proposed and tested to evaluate the usefulness of the tempering bead technique as a method of improving...
-
Simulation of fluid structure interaction in a novel design of high pressure axial piston pump
PublicationA novel type of an axial, piston-driven high pressure hydraulic pump with variable capacity marks a significant improvement in the area of the hydraulic machinery design. Total discharge from hydrostatic forces eliminates a need for a servomechanism, thus simplifying operation, reducing weight and introducing the possibility of the pump displacement control by computer. PWK-type pumps, invented in the Gdansk University of Technology,...