Search
Filters
total: 1219
filtered: 1025
displaying 1000 best results Help
Search results for: NUMERICAL SIMULATIONS, CFD, CHIP REMOVING SYSTEM, SLIDING TABLE SAW
-
Chip suction system in circular sawing machine: empirical research and computational fluid dynamics numerical simulations
PublicationThe experimental analysis of the wood chip removing system during its redesigning in the existing sliding table circular saw and computational fluid dynamic (CFD) numerical simulations of the air flow process is presented in the paper. The attention was focused on the extraction hood and the bottom shelter of the actual existing system. The main aim was to perform experimental research on the pressure distribution inside the...
-
Optimization of chip removing system operation in circular sawing machine
PublicationThe paper presents the optimization of the wood chips removing system in the sliding table saw. Chips are generated during the cutting of the material. The attention was focused on the upper casing of mentioned system. The methodical experimental studies of the pressure distribution inside the casing during the wood chip removing operation for the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm were...
-
Experimental examination and modification of chip suction system in circular sawing machine
PublicationThe article presents the results of experimental examination of the wood chip suction system in the existing sliding table saw before and after its modifi cation. The studies focused on the extraction hood of the mentioned system. The methodical experimental research of the pressure distribution inside the hood during wood chip removal for the selected rotational speed of saw blades of 3500 and 6000 min-1 with a diameter of 300...
-
Numerical analysis of chip removing system operation in circular sawing machine using CFD software
PublicationPaper presents the analysis of the results of numerical simulations of the air flow process of wood chips removing system in the circular sawing machine. The attention is focused on the upper cover and bottom shelter of the chip removing system. Within the framework of the work a systematic numerical modeling of the air flow distribution in the cover and shelter during operation of the selected rotational speed of saw blade with...
-
Analysis of the design development of the sliding table saw spindles
PublicationProducers of sliding table saws constantly strive for improvement in sawing accuracy. One of the method is an upswing in a spindle behavior, since, it affects to a large degree sawing effects. The design development of sliding table saw spindles during the last quarter-century is presented. The spindle system of the modernized spindle of the sawing machine Fx550 is described.
-
Experimental analysis of chip removing system in circular sawing machine
PublicationPaper presents analysis of the process of removing the wood chips generated during the cutting of the material on the circular sawing machine. The attention is focused on the upper cover of the chip removing system. Within the framework of the work a systematic experimental study of pressure distribution in the cover during operation of the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm was carried...
-
The Design Development of the Sliding Table Saw Towards Improving Its Dynamic Properties
PublicationCutting wood with circular saws is a popular machining operation in the woodworking and furniture industries. In the latter sliding table saws (panel saws) are commonly used for cutting of medium density fiberboards (MDF), high density fiberboards (HDF), laminate veneer lumber (LVL), plywood and chipboards of different structures. The most demanded requirements for machine tools are accuracy and precision, which mainly depend on...
-
Application in circular sawing machines of the experimental results of investigations of the chip removing system operation
PublicationThe experimental results of the chip removing system operation are presented. The main aim of them was to optimize suction system of the panel saw Fx3 and its follower Fx550. The attention was focused on the upper casing, which was the part of removing system. Within the framework of the work a systematic experimental study of pressure distribution in the casing during operation of the selected rotational speed of saw blade with...
-
Analyses of the effect of the design features of the spindle of the sliding table saw upon its critical rotational speeds
PublicationProducenci pilarek formatowych do drewna dążą do zwiększania dokładności przecinania. Można to osiągnąć np. przez poprawę zachowania się wrzeciona, gdyż od niego w dużej mierze zależą efekty przecinania. Przedstawiono metodykę wyznaczania prędkości krytycznych wrzeciona pilarki formatowej w funkcji cech konstrukcyjnych wrzeciona i jego napędu.
-
COMPARISON OF SYSTEM ON CHIP TECHNOLOGIES FOR SPACE APPLICATIONS
PublicationThe paper presents a review of technologies available for the implementation of digital and mixed signal systems, particularly the system on a chip (SoC) for space applications. The phenomena encountered in the space environment are briefly presented, together with the known solutions, regarding the design of complex electronic systems. The most important norms regarding single die integrated circuits designed for space are also...
-
Prediction of ship resistance with the use of Full-scale CFD simulations
PublicationIn recent years, the IMO has introduced new regulations to reduce the negative impact of ships on the natural environment. A particularly important step forcing technological innovations is the increasing requirement of ship energy efficiency. It is expressed by the Energy Efficiency Design Index (EEDI). Another important step towards green shipping is rising the required quality of fuel used for propulsion, so called Tier limits....
-
Improvement of ships seakeeping performance by application of the full-scale cfd simulations
PublicationThe ship’s fuel economy is increasingly important. The paper presents the effect of redesigning a case study ship for increasing seakeeping performance. Selected wave parameters reflect very difficult operational conditions existing on the North Sea and the Baltic Sea. The analyzed variants of a case study ship represent the latest developments of modern hull forms. The concepts similar to V-shaped bulbous bow, X-bow, X-aft, B-bow...
-
Full-scale CFD simulations for the determination of ship resistance as a rational, alternative method to towing tank experiments
PublicationResults of ship resistance predictions obtained from towing tank experiments are affected by the method used to extrapolate from a model scale to a ship scale. Selection of method to determine a form factor is subjective and the extrapolation method is accurate for typical hull forms. For innovative hull forms the proper method for calculating the form factor is questionable. Moreover, the influence of the extrapolation method...
-
Improvement of ships seakeeping performance by application of the Full-scale CFD simulations – case study
PublicationThe ship’s fuel economy is increasingly important. The paper presents the effect of redesigning a case study ship for increasing seakeeping performance. Selected wave parameters reflects very difficult operational con-ditions existing on the North Sea and the Baltic Sea. The analyzed variants of a case study ship represent the latest developments of modern hull forms. The concepts similar to V-shaped bulbous bow, X-bow, X-aft,...
-
Numerical Simulations for Transonic Flow in Control Valve
PublicationResults of numerical simulations for transonic flow in control valve are presented. The valve is the main part of an adaptive pneumatic shock absorber. Flow structure in the valve domain and the influence of the flow non-uniformity in the valve on a mass flow rate is investigated. Numerical simulation results are compared with experimental data.
-
Application of advanced CFD simulations in seakeeping analysis of ships (case study)
PublicationThe novel design process of many types of ships needs estimation of seakeeping properties. Especially ships like Offshore Supply Vessels, Wind Farm Support Vessels, Research Vessels, ferries, military vessels, rescue vessels require extended analysis of ship behavior on rough sea. The main reason for improving ships operability in different sea conditions is need of rising efficiency of propulsion system, reducing hull added resistance,...
-
Numerical Simulations of Hydrodynamic Open-Water Characteristics of a Ship Propeller
PublicationThe paper presents the results of numerical simulations of ship propeller operation bearing the name of Propeller Open Water (POW) Tests. The object of tests was a sample ship propeller (PPTC1), the geometrical and kinematic data of which are available, along with the results of model tests, on the official page of the research centre involved in the measurements. The research aimed at verifying the correctness of results of numerical...
-
Simulations of hydro-fracking in rock mass at meso-scale using fully coupled DEM/CFD approach
PublicationThe paper deals with two-dimensional (2D) numerical modelling of hydro-fracking (hydraulic fracturing) in rocks at the meso-scale. A numerical model was developed to characterize the properties of fluid-driven fractures in rocks by combining the discrete element method (DEM) with computational fluid dynamics (CFD). The mechanical behaviour of the rock matrix was simulated with DEM and the behaviour of the fracturing fluid flow...
-
Numerical simulations of novel GFRP sandwich footbridge
PublicationIn the following paper some aspects of numerical analysis and designing stages of a footbridge made of composite materials are elucidated. Because of the used materials the design process in this case is not ordinary and requires the development of concepts, material selections, identification of material properties, numerical simulations, strength calculations, serviceability and durability analyses. This contribution presents...
-
Towards improved energy efficiency of future smart ships by application of advanced CFD simulations – case study
PublicationThe international trade plays crucial role in today’s globally developed world’s economy. Many people are unaware of the unimaginable volume of cargo being transported every year by oceans and seas. For most of the time invisible from land the shipping industry preserves its strong position of the most cost-efficient and environmental friendly mean of transport. However during last years the shipping industry is under great pressure...
-
Full scale CFD seakeeping simulations for case study ship redesigned from V-shaped bulbous bow to X-bow hull form
PublicationIncreasing propulsion efficiency, safety, comfort and operability are of the great importance, especially for small ships operating on windy sites like the North Sea and the Baltic Sea. Seakeeping performance of ships and offshore structures can be analysed by different methods and the one that is becoming increasingly important is CFD RANS. The recent development of simulation techniques together with rising HPC accessibility...
-
TIME-DOMAIN NUMERICAL EVALUATION OF SHIP RESISTANCE AND MOTION IN REGULAR WAVES BY USING THE CFD URANS METHOD
PublicationTaking into account the International Maritime Organisation’s (IMO) strategy to radically reduce the GHG emitted by the shipping industry towards zero emission operation, today's assessment of ship behaviour in waves, its seakeeping characteristics and resistance and their interrelation with fuel consumption and emissions are one of the most attended research subject. There are three methods to conduct this analysis, which are...
-
Miernik elementów RLC na bazie układu ''programmable system On a Chip''
PublicationW artykule zaprezentowano miernik parametrów impedancyjnych oparty na układzie typu ''programmable system On a Chip'' firmy Cypress. Zawiera on w sobie mikroprocesor oraz reprogramowalne bloki analogowe i cyfrowe. Do budowy modelu wykorzystano układ CY8C26443, w którym zaimplementowano metodę pomiaru opartą na dyskretnym przekształceniu Fouriera pozwalającą, na podstawie zebranych próbek napięcia i prądu, wyznaczyć składowe Re...
-
[Chapter III] Influence of chip transport method on effects of cutting with circular saw
PublicationW pracy przedstawiono analizę transportu wiórów ze strefy skrawania na zewnątrz materiału obrabianego w procesie przecinania drewna piłami tarczowymi. Przedstawiono również przykłady zużycia pił tarczowych spowodowanych niewłaściwym transportem wiórów.
-
CFD Simulations and Tests of a Prototype Flow Control Valve
PublicationIn this paper a prototype of a flow control valve is described and numerically simulated. The flow control valve is used in hydraulic systems to maintain constant fluid flow despite changing loads of a receiver. The standard construction of this type of valves is modified mainly by eliminating the spring. The prototype consists the hydrostatically unloaded throttle valve and pressure ratio valve substituting pressure difference...
-
Wirtualny analizator stanów logicznych na bazie układu typu "System on a Chip"
PublicationW dobie dominacji układów cyfrowych, jednym z ważniejszych narzędzi uruchomieniowych jest analizator stanów logicznych (ASL). Komercyjne przyrządy nie są tanie, choć ich możliwości diagnostyczne uzasadniają cenę. W artykule przedstawiono ASL w konwencji przyrządu wirtualnego połączonego z PC poprzez interfejs USB, co obniża koszt urządzenia bez znaczącego pogorszenia jego możliwości. Wykorzystano układ typu SoC "System on a Chip"...
-
Experimental tests and numerical simulations of full scale composite sandwich segment of a foot- and cycle- bridge
PublicationIn the paper experimental tests and numerical simulations of a full cross-section segment of ultimately designed foot-and cycle-bridge are presented. The experimental tests were conducted on element with length reduced to 3 m and unchanged (target) cross-section dimensions. The external skin of structure is GFRP laminate while internal core is PET foam. Several quasi-static tests were performed using hydraulic cylinder to generate...
-
Surface sliding in human abdominal wall numerical models: Comparison of single-surface and multi-surface composites
PublicationDetermining mechanical properties of abdominal soft tissues requires a coupled experimental-numerical study, but first an appropriate numerical model needs to be built. Precise modeling of human abdominal wall mechanics is difficult because of its complicated multi-layer composition and large variation between specimens. There are several approaches concerning simplification of numerical models, but it is unclear how far one could...
-
Towards a modification of a regulatory framework aiming at bunker oil spill prevention from ships - A design aspect of bunker tanks vents location guided by CFD simulations
PublicationAlthough accidental bunker oil spills at seaway are relatively rare events, they can be pose real threat to the natural marine environment. One of the reasons for the bunker spill to occur is a design failure; one of the ways it can demonstrate is an improper location or height of vent heads, leading to a bunker oil discharge during heavy rolling, due to sloshing phenomenon. Design of a ship and her systems is guided by various...
-
The 4th Generation of CeSFaMB in numerical simulations for CuO-based oxygen carrier in CLC system
Publication -
TIME-DOMAIN NUMERICAL EVALUATION OF SHIP RESISTANCE AND MOTION IN REGULAR WAVES BY USING THE CFD URANS METHOD
PublicationTaking into account the International Maritime Organization's (IMO) strategy to radically reduce the...
-
System for control of the saw tooth geometry.
PublicationW pracy przedstawiono sposób i urządzenie do sprawdzania geometrii ostrzy pił tarczowych z wykorzystaniem komputerowej rejestracji obrazów ostrzy i ich obróbką cyfrową.
-
Numerical Simulations and Tracer Studies as a Tool to Support Water Circulation Modeling in Breeding Reservoirs
PublicationThe article presents a proposal of a method for computer-aided design and analysis of breeding reservoirs in zoos and aquariums. The method applied involves the use of computer simulations of water circulation in breeding pools. A mathematical model of a pool was developed, and a tracer study was carried out. A simplified model of two-dimensional flow in the form of a biharmonic equation for the stream function (converted into...
-
Static Load Test on Instrumented Pile – Field Data and Numerical Simulations
PublicationFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Numerical analysis of the ostiomeatal complex aeration using the CFD method
PublicationWe aimed to analyse ostiomeatal complex (OMC) aeration using the computational fluid dynamics (CFD) method of simulation based on human craniofacial computed tomography (CT) scans. The analysis was based on CT images of 2 patients: one with normal nose anatomy and one with nasal septal deviation (NSD). The Reynolds-Average Simulation approach and turbulence model based on linear eddy viscosity supplemented with the two-equation...
-
Prediction of cast-in-place concrete strength of the extradosed bridge deck based on temperature monitoring and numerical simulations
PublicationThe work is devoted to the implementation of a monitoring system for high performance concrete embedded in the span of an extradosed bridge deck using a modified maturity method augmented by numerical simulations conducted by the authors’ FEM code. The paper presents all research stages of bridge construction and considers the conclusions drawn from the results of laboratory tests, field measurements, and numerical calculations....
-
Speed estimation of a car at impact with a W-beam guardrail using numerical simulations and machine learning
PublicationThis paper aimed at developing a new method of estimating the impact speed of a passenger car at the moment of a crash into a W-beam road safety barrier. The determination of such a speed based on the accident outcomes is demanding, because often there is no access to full accident data. However, accurate determination of the impact speed is one of the key elements in the reconstruction of road accidents. A machine learning algorithm...
-
Hardware cryptography coprocessor for system on chip soft processor
PublicationW artykule przedstawiono realizację sprzętową i programową szyfrującejo i deszyfrującego algorytmu AES.Obydwie implementacje zostały zralizowane z wykorzystaniem układu Virtex II i przetestowane. Jako kryterium porónawcze wybrano zużycie zasobów układu oraz wydajność. Realizacja sprzętowa wykonuje operację szyfrowania 2 dekady szybcie niż wersja programowa, ale wymaga pięciokrotnie więcej zasobówIn this paper hardware and software...
-
Numerical Simulations of Seepage in Dikes Using unsaturated and Two-Phase Flow Models
PublicationModeling of water flow in variably saturated porous media, including flood dikes, is often based on the Richards equation, which neglects the flow of pore air, assuming that it remains at constant atmospheric pressure. However, there is also evidence that the air flow can be important, especially when the connectivity between the pore air and atmospheric air is lost. In such cases a full two-phase air-water flow model should be...
-
Experimental and numerical analysis of the modified TB32 crash tests of the cable barrier system
PublicationRoad restraint systems, including safety barriers, are one of the means used to improve road safety. Currently, they can be allowed to general use after passing the specific crash tests. However, it is always important and desirable to evaluate their performance under various realistic conditions, which can happen on the roads. In this study, the behaviour of the cable barrier system in impact conditions different than assumed...
-
Numerical simulations of overflow experiments on a model dike
PublicationDike failure due to overtopping is one of the important factors, which should be considered in the dike designing process. Although the overflow is characterized by the relatively low risk of occurrence, in many cases dikes are totally destroyed or seriously damaged. An interesting phenomenon occurring during overflow is the trapping of air in pores of the unsaturated soil material. As the infiltration progresses from all sides,...
-
Novel strategies to enhance hydrodynamic cavitation in a circular venturi using RANS numerical simulations
PublicationHydrodynamic cavitation is a popular advanced oxidation technique and it has received wide range of applications from waste water treatment to the nanoparticles synthesis in recent years. The enhancement of the intensity of the hydrodynamic cavitation is always been an emerging field of research. Within this framework, we have proposed and investigated three distinct strategies to enhance the intensity of cavitation in a circular...
-
A conceptual design and numerical analysis of the mixerless urea-SCR system
PublicationIn the present study, an innovative design of the urea-selective catalytic reduction (SCR) system without conventional mixing elements was developed. The aim was to obtain a high degree of urea decomposition, and uniform ammonia distribution at the inlet to the catalyst, while minimising the liquid film deposition and keeping the compact design. The concept of the design was based on creating high turbulences and elongating...
-
Numerical Determination of the Load-Bearing Capacity of a Perforated Thin-Walled Beam in a Structural System with a Steel Grating
PublicationThis article presents the results of numerical simulations of a structural system consisting of steel perforated thin-walled beams and a steel grating. The simulations were conducted using the finite element method. The analysis took into account physical and geometric nonlinearity as well as the contact between the steel grating and the beams. The main goal of the research was to develop load-bearing curves for the main beam in...
-
The role of numerical tests in assessing road restraint system functionality
PublicationKey to understanding the needs and building road infrastructure management tools to prevent and mitigate run-off-road accidents is to identify hazards and their sources which are a result of wrong design, construction, and installation of road restraint systems. Building such tools requires advanced studies with field tests, simulations and models to demonstrate the effects of selected parameters on road user safety. The research...
-
Ampacity of power cables exposed to solar radiation – recommendations of standards vs. CFD simulations
PublicationThe aim of the paper is to evaluate the ampacity of a low-voltage single power cable according to: 1) recommendations of the standard IEC 60287, 2) a Computational Fluid Dynamics method, implemented in Ansys software; and comparison of the results obtained for these two cases. Moreover, limitations of recommendations of the above mentioned standard are indicated.
-
The system for identification of the band saw wheel cross profile
PublicationPrzedstawiono system do identyfikacji zarysu poprzecznego koła pilarki taśmowej, dzięki któremu producent pił taśmowych ma możliwość naprężenia brzeszczotu piły w sposób zapewniający jej poprawną pracę. Opisano budowę i zasadę działania systemu. Uzyskane dane mogą być wprowadzane do układów sterowania automatycznych urządzeń ze sterowaniem CNC (naprężających piły taśmowe). Dane systemu: szerokość sprawdzanych kół do 300 mm, dokładność...
-
Monitoring of the circular saw vibrations with machine vision system.
PublicationPraca przedstawia metodologię wyznaczania drgań obracających się pił tarczowych z wykorzystaniem technik wizyjnych. Na podstawie otrzymanych wyników można wyznaczyc prędkości krytyczne piły oraz podac obszary prędkości zalecanych (najmniejsze wartości drgań poprzecznych piły).
-
Mechatronic system for automatic inspection of circular saw teeth
PublicationArtykuł prezentuje system mechatroniczny do automatycznej oceny geometrii ostrzy pił tarczowych. Opisywany system wizyjny został zastosowany w automatycznym kontrolerze ostrzy pił tarczowych WKOPTar. Wrzeciono urządzenia posiada swój napęd sterowany bezstopniowo obrazem ostrzy i zapewnia powtarzalne pozycjonowanie ostrzy w celu przechwycenia ich obrazów, które są następnie analizowane z wykorzystaniem specjalnego oprogramowania....
-
Computer vision monitoring system for circular saw teeth.
PublicationW pracy opisano zasadę działania urządzenia do wizyjnego monitoringu ostrzy pił tarczowych tyou WKOPTar, które w sposób automatyczny dokonuje pomiarów geometrii ostrzy oraz ich położenia w pile. Przedstawiono również analizę wyników badań na bazie zarejestrowanych ostrzy badanych pił tarczowych.