Search
Filters
total: 119
filtered: 114
Search results for: QUARTER VEHICLE SUSPENSION MODEL
-
Intelligent monitoring the vertical dynamics of wheeled inspection vehicles
PublicationThe problem of intelligent monitoring of the vertical dynamics of wheeled inspection vehicles is addressed. With the independent MacPherson suspension system installed, the basic analysis focuses on the evaluation of the parameters of the so-called quarter car model. To identify a physically motivated continuous description, in practice, dedicated integral-horizontal filters are used. The obtained discrete model, which retains...
-
Contribution of dynamic vehicle loads to pavement failure
PublicationPavement surfaces are not ideally even, which causes dynamic loads of vehicle axles. Distribution of dynamic loads of a given axle is similar to normal distribution and can be described by static load and dynamic load coefficient. The dynamic load coefficient depends on road profile, vehicle speed, properties of suspensions and static load of axle. While for a given road section road profile remains constant, vehicle speed and...
-
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublicationThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
Technical diagnostics and monitoring of traction current collectors
PublicationNew evaluation methods of the technical condition of rolling stock current collectors are proposed in this paper. The method of automatic measurement of the pantograph static force characteristic, realized when the vehicle runs through the test section of the track with especially prepared overhead line height distribution, has been practically implemented by the Polish Railways. The method of testing the slipper spring suspension...
-
Discrete identification of continuous non-linear and non-stationary dynamical systems that is insensitive to noise correlation and measurement outliers
PublicationThe paper uses specific parameter estimation methods to identify the coefficients of continuous-time models represented by linear and non-linear ordinary differential equations. The necessary approximation of such systems in discrete time in the form of utility models is achieved by the use of properly tuned `integrating filters' of the FIR type. The resulting discrete-time descriptions retain the original continuous parameterization...
-
Investigation method of large-volume tire with mobile test rig
PublicationThe goal of this research is to develop the tire test method and mobile tire test rig. The test rig enables measurement of tire properties as stiffness and viscous damping in vertical direction, and tire–ground characteristics on the asphalt rigid surface. The tire-ground characteristics are measured by force and a torque measurement hub. The design, calibration and the algorithm for calculating the forces in the wheel center are...
-
CFD and FEM model of an underwater vehicle propeller
PublicationDuring the project execution of design and optimization the Remotely Operated Vehicle (ROV) research on its propulsion has been carried out. The entire project was supported by CFD and FEM calculations, which taking into account the characteristics of underwater vehicle. One of the tasks was to optimize the semi-open duct for horizontal propellers, which provided propulsion and controllability in horizontal plane. In order to...
-
An Intergrated Model of Motion, Steering, Positioning and Stabilization of an Unmanned Autonomous Maritime Vehicle
PublicationIn the paper the aim of an interdisciplinary research is presented. The research method is introduced. An object the unmanned autonomous maritime vehicle is briefly described. The key research problem concerns a combined model of the vehicle motion including the loads of lift and hydrodynamic nature. The model takes into account the gravity and displacement forces, resistance and thrust forces, lift and other hydrodynamic forces....
-
Four-state stochastic model of changes in the reliability states of a motor vehicle
PublicationThe properties of semi-Markov processes have been generally characterized and the applicability of the theory of such processes to the determining of the reliability of motor cars and other road vehicles has been explained. A formal description of the process of changes in the motor vehicle technical states considered as reliability states and a model of this process in the form of a one-dimensional stochastic process have been...
-
Energetic model of hydraulic system of refuse collection vehicle based on simulation and experimental data
PublicationThis paper presents an energetic model of hydraulic system of a refuse collection vehicle. First, benefits resulting from implementation of an energetic model in the industry and operation of a Refuse Collection Vehicle are briefly explained. Then, components of the energy consumption in hydraulic circuits of compactor and lifting device are described and combined into a comprehensive model that can be evaluated using basic measurement...
-
Model Predictive Super-Twisting Sliding Mode Control for An Autonomous Surface Vehicle
PublicationThis paper presents a new robust Model Predictive Control (MPC) algorithm for trajectory tracking of an Autonomous Surface Vehicle (ASV) in presence of the time-varying external disturbances including winds, waves and ocean currents as well as dynamical uncertainties. For fulfilling the robustness property, a sliding mode control-based procedure for designing of MPC and a super-twisting term are adopted. The MPC algorithm has been...
-
Robust Model Predictive Control for Autonomous Underwater Vehicle – Manipulator System with Fuzzy Compensator
PublicationThis paper proposes an improved Model Predictive Control (MPC) approach including a fuzzy compensator in order to track desired trajectories of autonomous Underwater Vehicle Manipulator Systems (UVMS). The tracking performance can be affected by robot dynamical model uncertainties and applied external disturbances. Nevertheless, the MPC as a known proficient nonlinear control approach should be improved by the uncertainty estimator...
-
A laboratory model of an inspection vehicle. [Model laboratoryjny pojazdu inspekcyjnego]
PublicationW pracy opisano konstrukcję laboratoryjnego modelu pojazdu inspekcyjnego oraz zaproponowano system wielowątkowego sterowania pojazdem. Do budowy autonomicznego pojazdu wykorzystano napędzany elektrycznie już istniejący model laboratoryjny samochodu osobowego. Konstruowany pojazd wyposażono w specjalnie zaprojektowane elektroniczne układy czujnikowe pozwalające wykrywać i śledzić zaznaczoną kolorem czarnym trasę oraz mierzyć odległości...
-
Robust Model Predictive Control for Autonomous Underwater Vehicle–Manipulator System with Fuzzy Compensator
PublicationThis paper proposes an improved Model Predictive Control (MPC) approach including a fuzzy compensator in order totrack desired trajectories of autonomous Underwater Vehicle Manipulator Systems (UVMS). The tracking performancecan be affected by robot dynamical model uncertainties and applied external disturbances. Nevertheless, the MPCas a known proficient nonlinear control approach should be improved by the...
-
Development of the urban rail vehicle acoustic model
Publication -
Mathematical Model of the Vehicle Exploitation System of the Tactical Air Base
Publication -
Model of the hydraulic pump powertrain of refuse collection vehicle compaction mechanism
PublicationW pracy przedstawiono symulację pracy układu napędowego pompy hydraulicznej mechanizmu prasującego śmieciarki oraz wpływ różnych konfiguracji elementów składowych tego urządzenia na zużycie paliwa silnika napędowego w warunkach przyjętego cyklu obciążenia. W tym celu wykorzystano model układu napędowego pompy hydraulicznej mechanizmu prasującego śmieciarki w formie grafów wiązań oraz wyniki pomiarów ciśnienia roboczego w siłownikach...
-
Transmission system model in the track-vehicle relationship based on Long Term Evolution technology
Publication -
Social change: from the Solidarity y tmovement too urban movements -– a Design Thinking approach in co-producing city of Gdansk
PublicationThis paper presents a model of bottom-up revitalization of Gdansk's urban quarter using Design Thinking approach as users needs oriented method co-producing of space. This project is introduced as a possible canva to elaborate the model of intervention for other spaces in need of similar intervention.
-
Consequences of russia’s military invasion of Ukraine for Polish-Ukrainian trade relations
PublicationAn accurate forecast of interstate trade volume allows for short-term and long-term planning, particularly deciding on state budget revenues, foreign exchange earnings, border arrangement, other infrastructure, migration and social policies. Hostilities are destructive so the russian military aggression against Ukraine in 2022 needs to be assessed in terms of its effects on key economic aspects of Polish-Ukrainian relations, as...
-
Impact of the surface evenness and texture on tire/road rolling resistance
PublicationThis paper deals with the issue of a surface's roughness and texture impact on tire/road rolling resistance. It includes a brief description of research aims, measurements and an analysis of results. It also presents observations and conclusions regarding drum facility modernisation which allows studies concerning surface's roughness and texture impact on tire/road rolling resistance.
-
Modeling of performance and safety of a multi-task unmanned autonomous maritime vehicle = Modelowanie ruchu i bezpieczeństwa wielozadaniowego bezzałogowego autonomicznego pojazdu wodnego
PublicationAt the beginning of the paper the aim of research is presented. Then the method is introduced. Next, the unmanned autonomous maritime vehicle is briefly described. The following chapter concerns a model of vehicle performance including the ballasting and motion. Some information on an integrated steering, positioning and stabilization system of the vehicle is briefly presented in the paper. Such the system enables to obtain a fully...
-
The Dynamics of Trade Relations between Ukraine and Romania: Modelling and Forecasting
PublicationThe article examines the monthly dynamics of exports, imports and balance of trade between Ukraine and Romania in the period from 2005 to 2021. Time series from 2015 to 2021 were used for modelling and forecasting (since the date the European Union–Ukraine Association Agreement took effect). Adequate models of the dynamics series of the Box-Jenkins methodology were built: additive models with seasonal component ARIMA (Autoregressive...
-
Vibration of the bridge under moving singular loads - theoretical formulation and numerical solution
PublicationThe paper presents the results of the numerical analysis of a simple vehicle passing over a simply supported bridge span. The bridge is modelled by a Euler-Bernoulli beam. The vehicle is modelled as a linear, visco-elastic oscillator, moving at a constant speed. The system is described by a set of differential equations of motion and solved numerically using the Runge-Kutta algorithm. The results are compared with the solution...
-
On the validation of the LS-DYNA Geo Metro numerical model
PublicationThe paper presents experiences gained during work with numerical model of Geo Metro vehicle used for simulations of crash tests with road safety barriers. Attention is drawn to the subject of tire/wheel breakage during collision events. Some methods for improvement of the model are presented in the paper. Several results for the normative vehicle numerical tests are introduced. Simulations were carried out using LS-DYNA finite...
-
Analysis of the regenerative braking process for the urban traffic conditions
PublicationIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
Microfluidically Frequency-Reconfigurable Self-Quadruplexing Antenna Based on Substrate Integrated Square-Cavity
PublicationIn this article, a novel concept of self-quadruplexing tunable antenna (SQTA) enabled by microfluidic channels is investigated. The operating channels are either filled with air or dielectric liquids to enable frequency tunability. The proposed SQTA is implemented on the substrate-integrated square-cavity (SISC). A swastika-shaped slot is milled on the top-surface of the SISC to create four quarter-mode resonators. The resonators...
-
Deep Learning-Based Intrusion System for Vehicular Ad Hoc Networks
PublicationThe increasing use of the Internet with vehicles has made travel more convenient. However, hackers can attack intelligent vehicles through various technical loopholes, resulting in a range of security issues. Due to these security issues, the safety protection technology of the in-vehicle system has become a focus of research. Using the advanced autoencoder network and recurrent neural network in deep learning, we investigated...
-
Modeling, simulation, and validation of a TB41 crash test of the H2/W5/B concrete vehicle restraint system
PublicationThe paper addresses numerical simulations of a concrete vehicle restraint system. The model is described in detail. The advanced material law of the continuous surface cap model was used to analyze the damage locations in concrete barrier segments. The results were validated against the TB41 full-scale crash test. The test was conducted in compliance with European standard EN 1317, and the validation was performed in accordance...
-
Estimation of the Regenerative Braking Process Efficiency in Electric Vehicles
PublicationIn electric and hybrid vehicles, it is possible to recover energy from the braking process and reuse it to drive the vehicle using the batteries installed on-board. In the conditions of city traffic, the energy dissipated in the braking process constitutes a very large share of the total resistance to vehicle motion. Efficient use of the energy from the braking process enables a significant reduction of fuel and electricity consumption...
-
Dynamic risk assessment in autonomous vehicles motion planning
PublicationArguing that an autonomous mobile system is sufficiently safe to operate in presence of other vehicles and objects is an important element in development of such systems. Traditional approach to assure safety is to distinguish between safe and unsafe area and prevent the autonomous vehicle from entering the unsafe area. The paper presents a model of autonomous vehicle control system which uses risk assessment...
-
Microfluidically Frequency-Reconfigurable Compact Self-Quadruplexing Tunable Antenna with High Isolation Based on Substrate Integrated Waveguide
PublicationThis communication presents a novel concept of microfluidically frequency-reconfigurable self-quadruplexing tunable antenna for quad-band applications. At the initial design stage, a substrate-integrated square cavity is divided into four unequal quarter-mode cavity resonators by inserting an X-shaped slot on the top surface of the cavity. Applying four 50-ohm microstrip feed-lines to these four quarter-mode cavity resonators enables...
-
STUDY ON THE RELATIONSHIP BETWEEN VEHICLE MAINTENANCE AND FUEL CONSUMPTION
PublicationA contemporary road vehicle (RV) is a rather complex system, consisting of a large number of subsystems, assemblies, units, and elements (parts). While operating, an RV interacts with the environment, and its elements interact with each other. Consequently, the properties (parameters) of these elements change in the process - hardness, roughness, size, relative position, gapping, etc. A partial solution to the presented problems...
-
Inline Microstrip Bandpass Filter With Two Transmission Zeros and Increased Order Using Spurious Resonance of Frequency-Dependent Inverter
PublicationA design method for a class of fourth-order inline microstrip bandpass filter with two transmission zeros and 20% fractional bandwidth is presented. The filter consists of two quarter-wavelength transmission-line resonators coupled by a frequency-dependent inverter. The inverter is composed of two open-ended stubs that are connected by an interdigital capacitor and introduces two poles and two transmission zeros in the filter response....
-
Analytical modeling of electric drives for vehicle traction control systems
PublicationWheel-torque control bandwidth in vehicle dynamics model is crucial in evaluating optimal tracking ability of tire slip and in analysis of control system stability. Electric drives’ control dynamics are influenced by timing of digital control events, e.g. by sampling instant of motor currents. Reflecting this timing in drive analytical models is therefore important for analysis of vehicle traction systems. The paper considers five...
-
Analiza ruchowa pojazdów szynowych z uwzględnieniem zmian napięcia na odbieraku prądu
PublicationW artykule zaproponowano metodykę wykonywania analizy ruchowej pojazdów szynowych, która uwzględnia wpływ zmieniającego się napięcia zasilającego pojazd a jego właściwości ruchowe. Wykorzystując model opracowany w programie Simulink wskazano na istotne różnice w czasie przejazdu oraz w wartościach napięcia zasilającego pomiędzy proponowanym sposobem analizy a powszechnie stosowanym podejściem uproszczonym.
-
Practical Eco-Driving Strategy for Suburban Electric Multiple Unit
PublicationIn this paper, a practical approach to velocity profile optimization for electric multiple unit was presented. The study focuses on a case of fast urban railway, which is a popular mean of transport across Tricity, Poland. Based on observations and measurements, a potential for improvement of energy efficiency by modifying the speed profile was recognized. In order to conduct necessary calculations, simulation model of railway...
-
Speed estimation of a car at impact with a W-beam guardrail using numerical simulations and machine learning
PublicationThis paper aimed at developing a new method of estimating the impact speed of a passenger car at the moment of a crash into a W-beam road safety barrier. The determination of such a speed based on the accident outcomes is demanding, because often there is no access to full accident data. However, accurate determination of the impact speed is one of the key elements in the reconstruction of road accidents. A machine learning algorithm...
-
A compact microstrip rat-race coupler constituted by nonuniform transmission lines
PublicationIn this work, a step-by-step development of a compact microstrip rat-race coupler (RRC) has been presented and discussed. A high degree of miniaturization has been obtained by substituting six quarter-wavelength uniform atomic building blocks of a RRC by their nonuniform counterparts. The miniaturization procedure has been realized in three progressive steps: (i) the first layout solution of a miniaturized RRC has been acquired...
-
Effect of the Road Environment on Road Safety in Poland
PublicationRun-off-road accidents tend to be very severe because when a vehicle leaves the road, it will often crash into a solid obstacle (tree, pole, supports, front wall of a culvert, barrier). A statistical analysis of the data shows that Poland's main roadside hazard is trees and the severity of vehicles striking a tree in a run-off-road crash. The risks are particularly high in north-west Poland with many of the roads lined up with...
-
Wybrane wyniki badań potrzeb transportowych mieszkańców województwa pomorskiego
PublicationNa potrzeby opracowania Planu Zrównoważonego Rozwoju Publicznego Transportu Zbiorowego Województwa Pomorskiego w czwartym kwartale 2013 roku konsorcjum Fundacji Rozwoju Inżynierii Lądowej oraz z Politechniki Gdańskiej wykonało badania potrzeb transportowych mieszkańców województwa pomorskiego oraz wielkości popytu na usługi przewozowe. Uzyskane wyniki były podstawą do budowy transportowego modelu symulacyjnego podróży realizowanych...
-
Estimation of Vehicle Energy Consumption at Intersections Using Microscopic Traffic Models
PublicationThis paper addresses issues related to modeling energy consumption and emissions using microscopic traffic simulations. This paper develops a method in which a traffic model is used to calculate the energy needed to travel through selected types of intersections. This paper focuses on energy consumption and derived values of calculated energy, which can be, for example, carbon dioxide emissions. The authors present a review of...
-
Prediction of the fatigue lifetime of PUR structural elements using a combined experimental-numerical approach
PublicationThis paper presents a method for estimating the fatigue life of polyurethane elastomeric components. A rubber replacement - polyurethane of hardness 80ShA commonly used in vibration damping systems, for example, in motor vehicle suspensions, was used for the study. A metal-rubber bushing component was selected for analysis, and numerical analysis was carried out along with a fatigue model proposal based on a modification of the...
-
Modelling of dark fermentation of glucose and sour cabbage
PublicationIn the article, modified Anaerobic Digestion Models 1 (ADM-1) was tested for modelling dark fermentation for hydrogen production. The model refitting was done with the Euler method. The new model was based on sets of differential equations. The model was checked for hydrogen production from sour cabbage in batch and semi-batch in 5 g VSS (volatile solid suspension)/L and at the semi-batch process from glucose at 5 and 10 g VSS/L....
-
Space vector modulation in multilevel inverters of the servo drives of the trajectory measurements telescopes
PublicationUsing the MatLab/Simulink mathematical model of a three-phase three-level voltage inverter, the influence of the space-vector modulation (SVM) algorithm on the pulsations of the current (torque) of an AC motor in the range of low rotation speeds is considered. It is shown that the SVM of the second kind does not provide a pulsations level comparable to the pulsations of a sinusoidal pulse-width modulation (SPWM), both in the static...
-
Travel Time of Public Transport Vehicles Estimation
PublicationEffective prediction of speed is central to advanced traveler information and transportation management systems. The speed of public transport vehicles is affected by many external factors including traffic volume, organization and infrastructure. The literature presents methods for estimating travel time on sections of a transport network and vehicle arrival at stops, often making use of the AVL (automatic vehicle location). The...
-
Robust identification of quadrocopter model for control purposes
PublicationThe paper addresses a problem of quadrotor unmanned aerial vehicle (so-called X4-flyer or quadrocopter) utility model identification for control design purposes. To that goal the quadrotor model is assumed to be composed of two abstracted subsystems, namely a rigid body (plant) and four motors equipped with blades (actuators). The model of the former is acquired based on a well-established dynamic equations of motion while the...
-
Oddziaływania taboru na mosty kolejowe przy zmiennych parametrach ruchu
PublicationW pracy poruszono zagadnienia związane z identyfikacją oraz modelowaniem układu dynamicznego most-pojazd ruchomy. Za element szczególnie istotny uznano czynnik obciążający. Opracowano i wdrożono metodykę identyfikacji cech dynamicznych rzeczywistego pojazdu szynowego. Eksperyment badawczy przeprowadzono dla jednostki trakcyjnej EN57, jednak nie ma żadnych ograniczeń w stosowaniu metody dla innego, konwencjonalnego taboru szynowego....
-
Novel proposal for V2X systems and WBAN cooperation to improve road safety
PublicationIn this paper, a novel proposal of the automotive Vehicle-to-Everything system solution is presented. In this proposal, there are included the Machine to Machine type communication system and the sensor system based on a short-range the Wireless Body Area Network communication. The aim of this paper is the analysis of the model for communication, especially its architecture and signals structure for the proposed solution. The use...
-
Modelowanie i symulacja ruchu pojazdu zabytkowego podczas hamowania
PublicationOpracowano model samochodu zabytkowego z wykorzystaniem metody masa-sprężyna, służącego do symulacji procesu hamowania pojazdu zabytkowego z możliwością pomiaru drogi hamowania. Konfiguracja sieci połączeń między punktami mas elementów zawieszenia oraz opony okazuje się mieć bardzo duży wpływ na zachowanie symulowanego samochodu podczas hamowania. Poprawność symulacji sprawdzono porównując wyniki uzyskane z symulacji oraz z pomiarów...