Search results for: STEEL STRUCTURE
-
Evaluation of time and space distribution of magnetic flux density in a steel plate magnetized by a C-core
PublicationBadano wpływ częstości magnesowania płyty stalowej na rozkład przestrzenny indukcji magnetycznej wewnątrz tej płyty. Rozkład ten oceniano na podstawie pomiaru natężenia emisji magnetoakustycznej a także rozkładu na powierzchni płyty natężenia efektu Barkhausena. Wyniki dyskutowane są ilościowo i porównane z wynikami modelowania metodą elementów skończonych, w której uwzględniono efekt powstawania prądów wirowych.
-
Cavitation erosion behavior of 18/8 stainless steel after its laser alloying of manganese
PublicationW pracy przedstawiono wyniki badań własności kawitacyjnych stali nierdzewnej gatunku 18/8 po jej laserowym stopowaniu różną zawartością manganu. Stwierdzono, że przy zawartości Mn w ilości 7,13% występuje największy wzrost twardości po stopowaniu a głębokość umacniania na skutek działania obciążeń kawitacyjnych jest najmniejsza.
-
Potential and strain rate impact on the electrochemical properties of 304L stainless steel under tensile stresses.
PublicationPraca skupia się na badaniach aspektu elektrochemicznego i mechanicznego pękania warstwy pasywnej obecnej na stali 304L. Przedstawione zostały wyniki chwilowych zmian impedancji oraz zmiany parametrów elektrochemicznych warstwy pasywnej podczas testów rozciągania przy różnych poziomach polaryzacji anodowej oraz szybkości rozciągania. Na ich podstawie można stwierdzić, że zarówno czynnik elektrochemiczny, jak i mechaniczny wpływają...
-
Structural and Microhardness Changes After Turning of the AISI 1045 Steel for Minimum Quantity Cooling Lubrication
Publication -
SURFACE TEXTURE ANALYSIS AFTER BALL END MILLING WITH VARIOUS SURFACE INCLINATION OF HARDENED STEEL
Publication -
Optimisation of machining parameters during ball end milling of hardened steel with various surface inclinations
Publication -
Suspension and process parameters selection for electrophoretic deposition of Mn–Co spinel coating on steel interconnects
PublicationMetallic interconnect coatings, consisting of MnCo2O4 spinel, were effectively applied to Crofer 22 APU using the electrophoretic deposition (EPD) method in both H2O: ethanol and pure ethanol solvents. The primary goal of this method was to prevent chromium migration, minimize evaporation, and control the oxidation rate. The study aimed to assess the quality, adhesion, and thickness of the Mn–Co coating, with the objective of...
-
Effect of the Post-Weld Surface Condition on the Corrosion Resistance of Austenitic Stainless Steel AISI 304
PublicationSurfaces of welded elements made of corrosion-resistant (stainless) steels develop temper colours. The removal of thickened oxide layers off steels exposed to temperatures below 300°C is necessary and entails the restoring of high corrosion resistance of the stainless steel. The article presents tests concerned with the effect of a method applied to remove post-weld temper on the corrosion resistance of austenitic stainless steel...
-
High temperature corrosion of steel equipment in modern rafinery environments with high and low sulphur content
PublicationPrzedstawiono charakterystykę i mechanizmy procesów wysokotemperaturowej korozji elementów ze stali we współczesnych rafineriach ropy naftowej podczas eksploatacji we frakcjach węglowodorowych o niskiej i wysokiej zawartości siarki. Zwrócono uwagę na procesy korozji siarkowej w obecności wodoru i bez obecności wodoru oraz proces pylenia metalu pod wpływem węgla ze środowiska - w wypadku niskiej zawartości siarki w środowisku.
-
Influence of the laser remelting parameters on the thickness of surface layers created on the stainless steel X5CrNi18-10
PublicationIn this work the surface of austenitic stainless steel type X5CrNi18-10 was treated by using laser. Laser remelting was done by means of laser MLT 2500 CO2 with different parameters of treatment: P - power beam (800 [W], 1000 [W], 1100 [W], 1200 [W]); v - scanning velocity (6 [mm/s], 7 [mm/s], 8 [mm/s]); diameter of laser beam (1.4 [mm], 1.6 [mm]). The influence of these parameters on the thickness and shape of layers in manufacturing...
-
Evaluation of porous ferritic Fe22Cr stainless steel for solid oxide fuel cells at high temperature
PublicationW pracy przedstawiono wyniki badań korozji stali Fe22Cr w wysokich temperaturach.
-
Impact of Tensile and Compressive Stress on Classical and Acoustic Barkhausen Effects in Grain-Oriented Electrical Steel
PublicationIn this paper, we present the results of the investigation of impact of tensile and compressive stress on the classical Barkhausen effect, magnetoacoustic emission (MAE) signal properties, and B(H) hysteresis loops for grain-oriented (GO) electrical steel. Samples have been glued to a nonmagnetic steel bar and stressed within elastic range (±800 μdef) by means of four-point bending method. The samples were cut out in two directions...
-
Safety of erection and repair of steel tanks with geometric imperfections using heavylift jack-up system
PublicationSafety analysis is performed of cylindrical vertical steel tanks during erection using heavylift jack up system. During an assembly or repair process a set of hydraulic supports is used. It allows to use the in-place lifting of heavy steel constructions on the required height. Wind can strongly influence stability of the lifted tank. Any geometric imperfections can reduce the critical or limit load. In the work failures of the...
-
Application of wavelet transform in analysis of guided wave propagation signals for damage detection in a steel plate
PublicationThe paper presents results of experimental investigations on damage detection using guided wave propagation technique. The tested specimen was a steel plate with a defect in the form of a rectangular notch. Lamb waves were excited by a PZT actuator and sensed by a laser vibrometer. Since reflections from damage in registered signals are often masked by measurement noise, for identification of time of reflections from damage, continuous...
-
The determination of deformations and stresses of laser welds used for fatigue assessment of steel sandwich panel joints
PublicationPanele typu sandwich znajdują szerokie zastosowanie w wielu gałęziach przemysłu. W przypadku niektórych zastosowań wymagających ocenę ryzyka dużą rolę odgrywa ocena trwałości zmęczeniowej spoin laserowych paneli. W pracy prezentowane są metody wyznaczania lokalnych odkształceń i naprężeń w połączeniach spawanych w celu oceny trwałości zmęczeniowej według hipotez lokalnych naprężeń i odkształceń.
-
THE COST ANALYSIS OF CORROSION PROTECTION SOLUTIONS FOR STEEL COMPONENTS IN TERMS OF THE OBJECT LIFE CYCLE COST
PublicationSteel materials, due to their numerous advantages - high availability, easiness of processing and possibility of almost any shaping are commonly applied in construction for carrying out basic carrier systems and auxiliary structures. However, the major disadvantage of this material is its high corrosion susceptibility, which depends strictly on the local conditions of the facility and the applied type of corrosion protection system....
-
Influence of laser processing of the low alloy medium carbon structural steel on the development of the fatigue crack
PublicationThe paper contains the results of the structural analysis, hardness tests and fatigue tests conducted for the medium carbon structural steel with low content of Cr and Ni after its processing with CO2 laser beam. Pre-cracks were made in the round compact tension (RCT) specimen used for fatigue test. Next, four paths, parallel to each other, were melted on both sides of the samples using a laser beam. The paths were perpendicular...
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublicationThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Performance of Vector-valued Intensity Measures for Estimating Residual Drift of Steel MRFs with Viscous Dampers
PublicationViscous Dampers (VDs) are widely used as passive energy dissipation system for improving seismic performance levels especially in retrofitting of buildings. Residual Inter-story Drift Ratio (R-IDR) is another important factor that specifies the condition of building after earthquake. The values of R-IDR illustrates the possibility of retrofitting and repairing of a building. Therefore, this study aims to explore the vector-valued...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATION ON SPECIMEN GEOMETRY EFFECT ON THE CTOD VALUE FOR VL-E36 SHIPBUILDING STEEL
PublicationThere are special cases in the marine industry, where additional material tests, such as the fracture toughness test, must be performed. Additional fracture toughness tests, such as CTOD (Crack Tip Opening Displacement), are typically performed on three-point bend specimens. The dimension that defines all the specimen dimensions is the thickness of the material to be tested. It is recommended by classification societies (e.g. DNVGL)...
-
Glass-ceramic sealants and steel interconnects: accelerated interfacial stability and reactivity tests at high temperature
PublicationHigh-temperature reactions between glass-ceramic sealants and Fe-Cr alloy interconnects may lead to the formation of undesirable phases, and consequently degradation of solid oxide fuel/electrolyser devices. In this work, three different glass-ceramic sealants (Na-containing, Ba-containing, Sr-containing compositions) and Fe22Cr stainless steel powders (raw and pre-oxidised) are considered in order to test their chemical reactivity...
-
Cyclic deformation and fracture behaviour of additive manufactured maraging steel under variable-amplitude loading
PublicationThe cyclic deformation and fracture behaviour of 18Ni300 maraging steel produced by laser beam powder bed fusion is studied under variable-amplitude loading. The tests were conducted under fully-reversed strain-controlled conditions with a loading sequence comprising three ascending cycles and three descending cycles repeated sequentially until failure. After the tests, fracture surfaces were examined using height and volume surface...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublicationThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
Fracture Areas Quantitative Investigating of Bending-Torsion Fatigued Low-Alloy High-Strength Steel
PublicationIn this study, the impact of pseudo-random non-proportional bending-torsion fatigue loadings proportion on the fatigue life and the fracture surface topography was analyzed. Investigation was carried out for 24 specimens made of S355J2 steel with 11 different ratios of maximum stresses λ. For these cases, after the fatigue tests, the surface topography measurements were carried out using an optical profilometer, using the focus...
-
Stress–strain model of lower corroded steel plates of normal strength for fitness-for-purpose analyses
PublicationThis study investigates the mechanical properties of specimens made of normal strength steel subjected to lower marine immersed corrosion degradation levels (below 25 %). The specimens were corroded in laboratory conditions, and only natural factors were controlled to raise the corrosion rate (reaching the level of 1 mm/year). Three different thicknesses of plates made of normal strength of shipbuilding steel are investigated (between...
-
Przygotowanie przemysłowego obiektu o stalowej konstrukcji nośnej do remontu po pożarze
PublicationW artykule przedstawiono warunki i sposób podejścia do naprawy stalowej konstrukcji nośnej kilkukondygnacyjnego obiektu przemysłowego, który uległ uszkodzeniu w wyniku oddziaływania wysokiej temperatury pożaru. Omówiono rodzaje badań i sprawdzeń oraz sposób przeprowadzenia kontroli konstrukcji, które stały się podstawą do wydania oceny technicznej o możliwości odbudowy i remontu obiektu, bez jego nadmiernej rozbiórki. Wskazany...
-
Impact performance of novel multi-layered prepacked aggregate fibrous composites under compression and bending
PublicationMulti-layered Prepacked aggregate fibrous composite (MLPAFC) is a new type of concrete, which is prepared in two subsequent stages of aggregate-fibre skeleton prepacking and cementitious grouting. In this study, ten MLPAFC mixtures were prepared in three subsequent layers incorporating different contents of four different types of steel fibres. Long and short hooked-end and crimped steel fibers were adopted with 3.0 and 1.5% dosages...
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublicationDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
The impact of material degradation on the resistance and reliability of truss structures
PublicationThe paper analyses limit load-carrying capacity and buckling load of truss towers used to support high voltage power lines. The analysed typical structure was subjected to characteristic loads and their combinations. The results were applied to assess structural resistance with regard to steel corrosion in the long-term operation. The extent of structural deterioration was assessed due to Young's modulus decrement in the course...
-
Finite element method simulations of various cases of crash tests with N2/W4/A steel road barrier
PublicationThe subject of this study is performance of N2/W4/A steel road safety barrier investigated in numerical simulations. System was checked under several types of initial conditions, which were assumed basing on the TB11 and TB32 normative crash tests. The main goal of present study is to investigate the relationship between initial conditions (angle and velocity) of the impact and the severity indices (associated to the vehicle occupant) during...
-
Influence of nonlinearities on the efficiency and accuracy of FEM calculations on the example of a steel build-up thin-walled column
PublicationDue to the increase of computing capabilities of standard processing units, it is possible to perform complex analyses, considering a number of nonlinearities, such as geometric, material and boundary (contact) even on personal computers. In the paper, the authors have analysed the efficiency and accuracy of standard PC’s FEM calculations performed in Abaqus CAE 2017 software on the example of a critical load assessment of a thin-walled...
-
Analysis of load carrying capacity and destruction mechanism of an intermediate anchorage steel plate for pillar jib crane
PublicationPillar jib cranes are often mounted to existing floors with the use of an intermediate anchorage steel plate instead of using independent foundations, what is shown in the figure. Standards for steel design provide only basic rules for the design of such an intermediate plate. This study presents a simple design approach by using a numerical model in order to analyze different parameters that have significant influence in the anchorage...
-
Evaluation of cavitation erosion–corrosion degradation of mild steel by means of dynamic impedance spectroscopy in galvanostatic mode
Publication -
Fatigue Damage Development in 14MoV6-3 Steel for Power Plant Pipes Monitored by Digital Image Correlation
Publication -
Experiments and Numerical Simulations of the Annealing Temperature Influence on the Residual Stresses Level in S700MC Steel Welded Elements
Publication -
Appliance of High Speed Camera during Industrial Exploitation on the Example of Static and Dynamic Tests of Steel Probes
Publication -
Strengthening mechanism and precipitate evolution of a multi-application special engineering steel designed based on a hybrid idea
Publication -
Complex Corrosion Properties of AISI 316L Steel Prepared by 3D Printing Technology for Possible Implant Applications
Publication -
Surface Layer Properties of Sintered Ferritic Stainless Steel Remelted and Alloyed with FeNi and Ni by HPDL Laser
Publication -
Laser Thermal Oxidation by Ytterbium-Doped Fibre Laser of the Hot and Cold-Rolled Stainless Steel Surface
Publication -
Effect of high temperature exposure on the fatigue damage development of X10CrMoVNb9-1 steel for power plant pipes
Publication -
Comparison of properties of magnetoacoustic emission and mechanical Barkhausen effects for P91 steel after plastic flow and creep
PublicationW artykule przedstawiono wyniki pogłębionej analizy sygnału szumowego efektu Barkhausena dla próbek ze stali krzemowej Fe-2%Si po deformacji plastycznej. Badane były próbki po walcowaniu na zimno powodującym odkształcenie względne w zakresie do 8%. Pierwsze podejście polegało na analizie w dziedzinie czasu widma badanego sygnału. Analiza ta została uzupełniona o analizę liczby zliczeń impulsów w funkcji napięcia progowego, zarówno...
-
Experimental validation of the use of energy transfer ratio (ETR) for damage diagnosis of steel-concrete composite beams
Publication -
Evaluation of hydrogen degradation susceptibility of high-strength weldable steel subjected to cathodic polarization in sea-water
PublicationOcenę podatności stali spawalnych o wysokiej wytrzymałości ich złączy spawanych na kruchość wodorową przeprowadzono z wykorzystaniem próby rozciągania ze stałą, niską szybkością odkształcenia w środowisku wody morskiej przy polaryzacji katodowej. Wykonano próby elektrochemiczne przenikania wodoru w wodzie morskiej dla oceny dyfuzji i pułapkowania wodoru. Badano wpływ bakterii redukujących siarczany na absorpcję wodoru w środowisku...
-
Impact of eddy currents on Barkhausen and magnetoacoustic emission intensity in a steel plate magnetized by a C-core electromagnet.
PublicationZbadano (zmierzono i modelowano metodą elementów skończonych) wpływ częstości magnesowania na przestrzenny i czasowy rozkład indukcji magnetycznej wewnątrz płyty stalowej. Wyznaczono i zmierzono natężenie polowego rozkładu Barkhausena (HEB) na powierzchni płyty oraz natężnie emisji magnetoakustycznej (EMA) z całej magnesowanej objętości. Wykazano, iż obserwowane zmiany w natężeniu HEB i EMA są wynikiem zmian w rozkładzie indukcji...
-
Development and experimental validation of a novel double-stage yield steel slit damper-buckling restrained brace
PublicationThis research is focused on the development and experimental validation of a novel double-stage yield steel slit damper-buckling restrained brace (SSD-DYB) system designed for seismic resistance of steel structures. The SSD-DYB integrates the energy dissipation capability of a steel slit damper (SSD) in its initial segment, enhancing performance in the case of lower seismic intensities levels while employing a larger segment for...
-
Wpływ obróbki cieplnej na strukturę stali krzemowej. The heat treatment influence on the silicon steel morphology
PublicationStal sprężynową 55S2 poddano obróbce cieplnej przy poprawnych i zawyżonych paramatrach temperaturowo-czasowych. Dla materiału o wadliwej strukturze wyjściowej, dobór wyższych temperatur i czasów obróbki pozwolił na otrzymanie bardziej poprawnych struktur i własności materiału.
-
Wear of carbide inserts during turning of C45 steel in dry cutting conditions and in presence of emulsion mist
Publication -
Formation of Surface Topography During Turning of AISI 1045 Steel Considering the Type of Cutting Edge Coating
Publication -
Numerical analysis of influence of intermediate stiffeners setting on the stability behaviour of thin-walled steel tank shell
Publication