Filters
total: 7061
displaying 1000 best results Help
Search results for: high-intensity sweeteners
-
High Resolution Sea Ice Floe Size and Shape Data from Knox Coast, East Antarctica
PublicationThis dataset contains floe size distribution data from a very high resolution (pixel size: 0.3 m) optical satellite image of sea ice, acquired on 16 Feb. 2019 off the Knox Coast (East Antarctica). The image shows relatively small ice floes produced by wave-induced breakup of landfast ice between Mill Island and Bowman Island. The ice floes are characterised by a narrow size distribution and angular, polygonal shapes, typical...
-
Compact High Efficiency and Zero-Emission Gas-Fired Power Plant with Oxy-Combustion and Carbon Capture
PublicationReduction of greenhouse gases emissions is a key challenge for the power generation industry, requiring the implementation of new designs and methods of electricity generation. This article presents a design solution for a novel thermodynamic cycle with two new devices—namely, a wet combustion chamber and a spray-ejector condenser. In the proposed cycle, high temperature occurs in the combustion chamber because of fuel combustion...
-
Safety issues referred to induced sheath voltages in high-voltage power cables – case study
PublicationLoad currents and short-circuit currents in high-voltage power cable lines are sources of the induced voltages in the power cables’ concentric metallic sheaths. When power cables operate with single-point bonding, which is the simplest bonding arrangement, these induced voltages may introduce an electric shock hazard or may lead to damage of the cables’ outer non-metallic sheaths at the unearthed end of the power cable line. To...
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plans. Part A: Public Power Plants 60+
PublicationAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. Variants with regeneration and different cogeneration systems were considered. In the paper, we propose a new modification of a gas turbine cycle with the combustion chamber at the turbine outlet. A special air by-pass system of the combustor was applied and, in this way, the efficiency of the turbine cycle was increased by a few points....
-
Pin-on-Substrate Gap Waveguide: An Extremely Low-Cost Realization of High-Performance Gap Waveguide Components
PublicationConsidering the limitations of currently available technologies for the realization of microwave components and antennas, a trade-off between different factors including the efficiency and fabrication cost is required. The main objective of this letter is to propose a novel method for the realization of gap waveguides (GWGs) that take advantage of conventional PCB fabrication technology, thus are low cost and light weight. Moreover,...
-
Experimental study of flow boiling pressure drop and heat transfer of R1233zd(E) at moderate and high saturation temperatures
PublicationThe paper presents the results of experimental study of flow boiling of R1233zd(E) in minichannel at moderate and high saturation temperatures. The heat transfer coefficient and pressure drop were measured for flow boiling in a stainless steel tube with 2 mm inside diameter and a length of 300 mm. Experiment has been conducted for saturation temperatures ranging from 83 to 145 °C which corresponds to values of reduced pressures...
-
Implementation of failover and load balancing algorithms in SIP PBX High Availability system
PublicationGoal of the project was to design a High Availability SIP VoIP system that guarantees access to additional services like auto-attendent and automatic call distribution. The realization of the project required system to have load balancing and failover algorithms implemented. From the end users’ point of view the whole system had to figure as a single element. After taking under consideration the known methods of implementations...
-
Seismic Response of High-Rise Buildings Equipped with Base Isolation and Non-Traditional Tuned Mass Dampers
PublicationOne of the methods in structural control is the application of combinational control systems in order to reduce the response of structures during earthquakes. The aim of the present paper is to verify the effectiveness of a hybrid control strategy, combining base isolation and non-traditional tuned mass dampers (TMDs) (i.e., TMDs with dashpots directly connected to the ground) in suppressing structural vibrations of high-rise buildings....
-
Determination of Moisture Content Profiles of Spruce Wood After High Temperature Process and Air Drying
PublicationThe results of moisture content of wood after the process of its drying under high temperature conditions and air drying are presented. Wood samples, namely spruce (Picea abies Karst.) from the northern part of Pomerania region in Poland, were subject of steam and air drying.The aim of experiments was to measure moisture content of wood in its cross sections using moisture meter WRD-100. The samples of thickness 70 mm and length...
-
On the use of the cumulative strain energy density for fatigue life assessment in advanced high-strength steels
PublicationIn this paper, the applicability of the cumulative strain energy density is explored as a fatigue indicator parameter for advanced high-strength steels subjected to strain-controlled conditions. Firstly, the cyclic stress-strain responses of nine steels, selected from three multiphase families, encompassing different elemental compositions and different heat treatment routes, were studied. Then, the predictive capabilities of the...
-
High temperature oxidation behavior of SUS430 SOFC interconnects with Mn-Co spinel coating in air
PublicationIn this study, SUS430 alloy is evaluated for its high temperature corrosion properties as a possible material for interconnects of solid oxide fuel cells (SOFCs). Samples are coated with Mn-Co by commercial physical vapor deposition (PVD) process and oxidized in air for 1250 h at 800 °C. A dense cubic Mn-Co-Fe spinel layer is formed on the surface, showing great effect on corrosion reduction compared with the samples without coating....
-
Improving the Performance of a Graphite Foil/Polyaniline Electrode Material by a Thin PEDOT:PSS Layer for Application in Flexible, High Power Supercapacitors
PublicationIn this study, we present a novel strategy for enhancing polyaniline stability and thus obtaining an electrode material with practical application in supercapacitors. A promising (graphite foil/polyaniline/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) GF/PANI/PEDOT:PSS) electrode material was characterized and used in the construction of a symmetric supercapacitor that provides an outstanding high power density. For this...
-
Preparation of methanation catalysts for high temperature SOEC by β-cyclodextrin-assisted impregnation of nano-CeO2 with transition metal oxides
PublicationThe aim of this work was to prepare and examine the catalytic activity of nanometric CeO2 decorated with transition metal oxides – Ni, Co, Cu, Fe and Mn – towards a high-temperature methanation process under SOEC CO2/H2O simulated co-electrolysis conditions. Samples were prepared using the wet impregnation method via the conventional process and with the addition of native cyclodextrin. The influence of β-cyclodextrin (βCD) onto...
-
High Signal Resolution Pulse Oximetry as a Prognostic Indicator of Radiotherapy Toxicity: A Pilot Study
PublicationIntroduction: Radiotherapy plays a prominent role in the multidisciplinary treatment of cancers. Despite new irradiation techniques, radiation-induced cardiotoxicity remains a leading cause of morbidity and mortality. Therefore, prognostic indicators of radiotherapy toxicity are essential. This study aimed to investigate the influence of applied radiotherapy on the pulse wave recording and thereby on...
-
Machine-learning methods for estimating compressive strength of high-performance alkali-activated concrete
PublicationHigh-performance alkali-activated concrete (HP-AAC) is acknowledged as a cementless and environmentally friendly material. It has recently received a substantial amount of interest not only due to the potential it has for being used instead of ordinary concrete but also owing to the concerns associated with climate change, sustainability, reduction of CO2 emissions, and energy consumption. The characteristics and amounts of the...
-
High-density Polyethylene - Expanded Perlite Composites: Structural Oriented Analysis of Mechanical and Thermomechanical Properties
PublicationAs part of this work, research was carried out on the effect of the addition of expanded perlite (PR) on the mechanical and thermomechanical properties of high-density polyethylene (PE) composites. Composites containing from 1 to 10 wt% of the inorganic filler were produced. Polyethylene-based composites manufactured by twin-screw extrusion and formed in the compression molding process were subjected to mechanical, thermomechanical,...
-
Systematic Water Uptake Energetics of Yttrium-Doped Barium Zirconate—A High Resolution Thermochemical Study
PublicationA combination of surface area analyzer and microcalorimetry was employed to investigate the in situ water uptake energetics and the mechanism of proton incorporation in yttrium-doped barium zirconate in the temperature range 200–400 °C. The BaZr1–xYxO3 solid solutions are made with variable yttrium content (x = 10, 20, and 30 mol %) by a controlled oxidant-peroxo synthesis method. The water uptake increases as the partial pressure...
-
Optimization-Based High-Frequency Circuit Miniaturization through Implicit and Explicit Constraint Handling: Recent Advances
PublicationMiniaturization trends in high-frequency electronics have led to accommodation challenges in the integration of the corresponding components. Size reduction thereof has become a practical necessity. At the same time, the increasing performance demands imposed on electronic systems remain in conflict with component miniaturization. On the practical side, the challenges related to handling design constraints are aggravated by the...
-
Identification of High-Value Dataset determinants: is there a silver bullet for efficient sustainability-oriented data-driven development?
PublicationOpen Government Data (OGD) are seen as one of the trends that has the potential to benefit the economy, improve the quality, efficiency, and transparency of public administration, and change the lives of citizens, and the society as a whole facilitating efficient sustainability-oriented data-driven services. However, the quick achievement of these benefits is closely related to the “value” of the OGD, i.e., how useful, and reusable...
-
Use of response surface methodology in characterization of properties of recycled high density polyethylene/ground tire rubber compositions
PublicationSearching for newways to utilize rubber and polymerwaste has been the focus of many studies conducted by research centers and companies worldwide. In this study, the influence of extrusion conditions on the properties of thermoplastic compositions containing post-production recycled high density polyethylene (PE-HD) and ground tire rubber (GTR) at 50:50 mass ratiowas examined. Response Surface Methodology (RSM) was used to determine...
-
Boron-Enhanced Growth of Micron-Scale Carbon-Based Nanowalls: A Route toward High Rates of Electrochemical Biosensing
PublicationIn this study, we have demonstrated the fabrication of novel materials called boron-doped carbon nanowalls (B:CNWs), which are characterized by remarkable electrochemical properties such as high standard rate constant (k°), low peak-to-peak separation value (ΔE) for the oxidation and reduction processes of the [Fe(CN)6]3–/4– redox system, and low surface resistivity. The B:CNW samples were deposited by the microwave plasma-assisted...
-
Flow boiling of R1233zd(E) in a 3 mm vertical tube at moderate and high reduced pressures
PublicationThe results of flow boiling of R1233zd(E) in a 3 mm vertical stainless steel tube are presented at moderate and high saturation temperatures. Integral flow characteristics in the form of pressure drop and heat transfer coefficient are discussed for saturation temperatures ranging from 115 to 145 °C (corresponding reduced pressures from 0.2 to 0.7), mass velocity of 800 kg/m2s and heat flux of 20 kW/m2. All of the obtained heat...
-
On Improved-Reliability Design Optimization of High-Frequency Structures Using Local Search Algorithms
PublicationThe role of numerical optimization has been continuously growing in the design of high-frequency structures, including microwave and antenna components. At the same time, accurate evaluation of electrical characteristics necessitates full-wave electromagnetic (EM) analysis, which is CPU intensive, especially for complex systems. As rigorous optimization routines involve repetitive EM simulations, the associated cost may be significant....
-
Bodybuilders and high-level meat consumers’ behavior towards rabbit, beef, chicken, turkey, and lamb meat: A comparative review
PublicationIn bodybuilders’ diets, protein plays a crucial role in supporting muscle growth and repairing damaged muscle tissue. These individuals meet their protein needs by combining dietary sources with supplements. Animal-based proteins are often preferred over plant-based proteins because they are believed to better support muscle protein synthesis. This review explores the meat consumption patterns of bodybuilders and high-level meat...
-
Optimization of clamping stiffness during milling of high-dimensional structures with the use of techniques of experiment – aided virtual prototyping
PublicationThe subject of this paper is a method of searching for conditions of minimizing the vibration level of a tool-high dimensional flexible workpiece, at unchangeable technological parameters of the machining process. It depends on repeatable change of the values of the stiffness coefficients as soon as an optimal vibration state of the workpiece approaches. There are assessed the values of dominant ”peaks” in the frequency spectra...
-
Independent dynamics of low, intermediate, and high frequency spectral intracranial EEG activities during human memory formation
PublicationA wide spectrum of brain rhythms are engaged throughout the human cortex in cognitive functions. How the rhythms of various frequency ranges are coordinated across the space of the human cortex and time of memory processing is inconclusive. They can either be coordinated together across the frequency spectrum at the same cortical site and time or induced independently in particular bands. We used a large dataset of human intracranial...
-
State-of-the-art framework for high-speed camera and photogrammetric use in geometry evaluation of prestressed concrete failure process
PublicationPrestressed structures are a key to the realization of the boldest architectural ideas, regardless of shape complexity, great height and large span. A characteristic feature of the prestressed structure is the better use of concrete material properties by insertion of internal forces. The internal forces are opposed to external loads effects (forces and deformations of structure). Prestressed reinforced concrete beams are characterized...
-
Pressure effects on the electronic structure and superconductivity of (TaNb)0.67(HfZrTi)0.33 high entropy alloy
PublicationEffects of pressure on the electronic structure, electron-phonon interaction, and superconductivity of the high entropy alloy ( TaNb ) 0.67 ( HfZrTi ) 0.33 are studied in the pressure range 0–100 GPa. The electronic structure is calculated using the Korringa-Kohn-Rostoker method with the coherent potential approximation. Effects of pressure on the lattice dynamics are simulated using the Debye-Grüneisen model and the Grüneisen...
-
Gaoya Wuli Xuebao/Chinese Journal of High Pressure Physics
Journals -
Review of High Pressure Science and Technology/Koatsuryoku No Kagaku To Gijutsu
Journals -
Qiangjiguang Yu Lizishu/High Power Laser and Particle Beams
Journals -
Photocatalytic degradation of acetaldehyde in high temperature reaction chamber
Open Research DataThis dataset contains chromatograms recorded during the decomposition of acetaldehyde in a high-temperature reaction chamber under UV irradiation using TiO2 (titanium dioxide) as photocatalysts. It includes data on the influence of flow rate, TiO2 (titanium dioxide) filling the entire reactor, a thin layer of TiO2 (titanium dioxide) supported on KBr...
-
A new procedure for the determination of distillation temperature distribution of high-boiling petroleum products and fractions
PublicationThe distribution of distillation temperatures of liquid and semi-fluid products, including petroleum fractions and products, is an important process and practical parameter. It provides information on properties of crude oil and content of particular fractions, classified on the basis of their boiling points, as well as the optimum conditions of atmospheric or vacuum distillation. At present, the distribution of distillation temperatures...
-
Some coatings of high cavitation resistance produced by CO2 laser beam. XIV International Symposium on Gas Flow, Chemical Lasers and High Power Lasers.
PublicationPrzedstawiono wyniki badań odporności kawitacyjnej stali 2H13, 45 i żelaza Armco po laserowym stopowaniu ich powierzchni różnymi kompozycjami proszków Co, Mo, Ni, Mn i Cr, Ti. Wykazano różne własności kawitacyjne otrzymanych warstw w zależności od otrzymanej mikrostruktury.
-
Analysis of possible application of high-temperature nuclear reactors to contemporary large-output steam power plants on ships
PublicationThis paper is aimed at analysis of possible application of helium to cooling high-temperature nuclear reactor to be used for generating steam in contemporary ship steam-turbine power plants of a large output with taking into account in particular variable operational parameters. In the first part of the paper types of contemporary ship power plants are presented. Features of today applied PWR reactors and proposed HTR reactors...
-
Performance of a new commercial high-definition 3D patient specific quality assurance system for CyberKnife robotic radiotherapy and radiosurgery
PublicationConventional two dimensional and low-definition measurement techniques for dosimetric verification of radiotherapy treatment deliveries are no longer adequate in the era of hypofractionation and extremely high dose gradients. New quality assurance (QA) tools with 3D capability and high definition are urgently needed. The purpose of this study was to evaluate the performance of one of the first such commercial systems as applied...
-
Modeling the impact of rotor movement on non-linearity of motor currents waveforms in high-speed PMSM drives
PublicationMotor current measurement techniques as well as predictive control algorithms for electric drives rely on an assumption of linear motor currents changes resulting from constant inverter output voltages. Recent research has reported that this assumption does not hold in motors with short electrical time constant, and in drives whose rotor position advances substantially during a control period. This paper proposes a simulation model...
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublicationThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
Laser Welding of UNS S33207 Hyper-Duplex Stainless Steel to 6061 Aluminum Alloy Using High Entropy Alloy as a Filler Material
PublicationThe high entropy alloy (HEA) filler used during the fabrication method determines the reliability of HEAs for steel-aluminum dissimilar alloy configuration. HEAs have a direct impact on the formation of intermetallic compounds (IMC) formed by the interaction of iron (Fe) and aluminum (Al), and influence the size of the joint’s interaction zone. A novel welding process for Fe-Al alloy joints was developed to prevent the development...
-
Spectroscopic study of atmospheric pressure 915 MHz microwave plasma at high argon flow rate
PublicationIn this paper results of optical emission spectroscopic (OES) study of atmospheric pressure microwave 915 MHz argon plasma are presented. The plasma was generated in microwave plasma source (MPS) cavity- resonant type. The aim of research was determination of electron excitation temperature Texc gas temperature Tg and electron number density ne. All experimental tests were performed with a gas flow rate of 100 and 200 l/min and...
-
High accuracy hydroacoustic system to study codend model parameters
PublicationWażnym zadaniem projektantów narzędzi połowowych jest stworzenie efektywnych narzędzi połowowych działających selektywnie poprzez optymalizacje ich geometrii. Hydroakustyczny system pomiaru geometrii modeli worków dorszowych opisany w artykule został zaprojektowany dla opracowania konstrukcji worka dorszowego na potrzeby rybołówstwa na Morzu Bałtyckim.System składa się z 10 par przetworników ultradźwiękowych, mikroprocesorowego...
-
Grinding specifics of plasma coatings melted with high-frequency currents
Publication -
Study of the process of tool forming made of high-strength materials
Publication -
High pressure luminescence and time resolved spectra of La2Be2O5:Pr3+
Publication -
Spectral properties of Cr3+ in SrLaGaO4 under high hydrostatic pressure.
Publication -
High pressure studies of Eu2+ and Mn2+ doped NaScSi2O6 clinopyroxenes
Publication -
High-pressure X-ray Diffraction Study of SrSi2O2N2:Eu2+
Publication -
High pressure luminescence and time resolved spectra of LiNbO3:Pr3+
Publication -
Porous, High Capacity Coatings for Solid Phase Microextraction by Sputtering
Publication -
Treatment of high blood pressure in acute stroke – The SCAST Study
Publication