Filters
total: 1435
displaying 1000 best results Help
Search results for: MARINE TURBINE ENGINE
-
Eulerian motion magnification applied to structural health monitoring of wind turbines
PublicationSeveral types of defects may occur in wind turbines, as physical damage of blades or gearbox malfunction. A wind farm monitoring and damage prediction system is built to observe abnormal vibrations of elements of wind turbine: blades, nacelle, and tower. Contactless methods are developed which do not require turbine stopping. In this work, structural health monitoring of a wind turbine is evaluated using a conversion from the captured...
-
The system for remote monitoring of a vertical axis wind farm
PublicationThe article presents a system for remote monitoring of working parameters of a wind turbine with a vertical axis. The monitoring system was built using a Raspberry PI 3 microcomputer with the Raspbian operating system and a MicroDAQ E2000 measuring card. The developed system enables monitoring the power output of the generator, torque on the turbine shaft, turbine speed and wind speed. The values of the monitored parameters are...
-
Bridge Ergonomic Design: A Review
PublicationHuman error remains the most common cause of marine incidents and it is worth emphasizing that navigator’s performance is directly affected by ergonomic factors on the bridge. Studies regarding influence of bridge design and work environment on the operator are rare, thus the main purpose of this paper is to fill in this gap. Documents issued by recognized organizations, research publications and additional sources were reviewed...
-
JOURNAL OF THE MARINE BIOLOGICAL ASSOCIATION OF THE UNITED KINGDOM
Journals -
Analysis of operations of combined STIG installation
PublicationSteam injection in gas turbines is interesting technology with good energetic and ecological properties of gas turbines. In these applications the heat of exhaust gases is used to produce steam, which is injected in the combustion chamber of a gas turbine. The steam injection increase the power and efficiency of the installation. there are some possibilities to increases the properties of STIG turbines, for example by meas of additional...
-
Guided wave propagation signals measured on corroded stiffened panels
Open Research DataThe fundamental antisymmetric Lamb mode was excited by piezoelectric transducers attached at the pre-selected points on stiffened panels, representing typical structural ship components. The specimens were exposed to accelerated marine corrosion degradation, so the signals were collected to analyze the influence of the degree of degradation on the wave...
-
Rotordynamic characteristics of a chamber seal
PublicationThe paper presents the results of numerical and experimental investigations into pressure forces generated in a turbine labyrinth seal of a modernized type. The experiments were performed on a single-stage air model turbine of the impulse type. The experiments were performed on a single-stage air model turbine of the impulse type. The experimental data were compared with theoretical results obtained by means of CFD Fluent Code....
-
SHORT REVIEW AND 3-D FEM ANALYSIS OF BASIC TYPES OF FOUNDATION FOR OFFSHORE WIND TURBINES
PublicationSome problems of the foundations of offshore wind turbines are considered in this paper. A short review is presented on the two basic types of foundations, i.e. monopiles and gravity foundations, including their basic features and applications as well as general design considerations. Also, some issues regarding analysis are discussed, including geotechnical problems and modelling techniques. A numerical model of offshores turbine...
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plans. Part A: Public Power Plants 60+
PublicationAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. Variants with regeneration and different cogeneration systems were considered. In the paper, we propose a new modification of a gas turbine cycle with the combustion chamber at the turbine outlet. A special air by-pass system of the combustor was applied and, in this way, the efficiency of the turbine cycle was increased by a few points....
-
Conception for diagnosing SI engines fed with biofuel in operation conditions
PublicationThe article deals with the question of diagnosing the high power self ignition (SI) engines fed with pro-ecologic fuels in an aspect of appearing operation problems. There has been presented the specific of action and techno-operation profile of the combustion engine foreseen as an investigations object. The preliminary conception of diagnostic investigations of the engine 7L35MC type produced in H. Cegielski - Poznan S.A. factory...
-
Thermodynamic modeling of combustion process of the internal combustion engines – an overview
PublicationThe mathematical description of combustion process in the internal combustion engines is a very difficult task, due to the variety of phenomena that occurring in the engine from the moment when the fuel-air mixture ignites up to the moment when intake and exhaust valves beginning open. Modeling of the combustion process plays an important role in the engine simulation, which allows to predict incylinder pressure during the combustion,...
-
Marcin Ciołek dr inż.
People -
Współdziałanie planowania przestrzennego ląd-woda: jak wykorzystać doświadczenia pilotażowego planu zagospodarowania dla zachodniej części Zatoki Gdańskiej = Co-operation/coexistence of land based and marine spatial planning - how to use the MSP Western Gulf of Gdańsk pilot plan experience
Publication -
The influence of settable parameters of switching gasoline/LPG on exhaust toxic emissions
PublicationThe main objective of the studies shown in the paper was to develop a proper strategy for settable parameters of ECU to decrease total emission of toxic components in composition of exhaust during a cold start phase. The experimental research has been performed for engine running at idle and for engine running on the chassis dynamometer (performing European Driving Test NEDC).
-
ANALIZA AERODYNAMICZNA ŁOPAT NA PRZYKŁADZIE PROJEKTU DWUWIRNIKOWEJ TURBINY WIATROWEJ MAŁEJ MOCY
PublicationW artykule przedstawiono proces projektowania oraz analizy aerodynamicznej łopat turbiny wiatrowej z wykorzystaniem metody BEMT (ang. Blade Element Momentum Theory). Dokonano doboru profili aerodynamicznych oraz opisano procedurę wyznaczania optymalnego rozkładu kątów zwichrowania i długości cięciw profili w funkcji długości łopaty dla założonych parametrów wejściowych. Dokonano obliczenia działających sił oraz generowanej mocy...
-
ANALIZA MOŻLIWOŚCI ZASTOSOWANIA STEROWANIA PREDYKCYJNEGO TURBINĄ PAROWĄ ELEKTROWNI JĄDROWEJ
PublicationArtykuł przedstawia wyniki wstępnej analizy możliwości zastosowania sterowania predykcyjnego MPC turbiną parową elektrowni jądrowej. Tradycyjnie przyjmuje się, że turbina pracuje w jednym punkcie pracy odpowiadającym jej mocy nominalnej, co pozwala na stosowanie klasycznych regulatorów PID. Synteza sterowania dla warunków zmiennego punktu pracy wymaga uwzględnienia nieliniowego charakteru procesów turbiny oraz możliwości naruszania...
-
Carbon dioxide potential reduction using Start-Stop system in a car
PublicationOperating fuel consumption increases significantly when the vehicle stops frequently while driving or when the engine is idling during braking. In such cases, the internal combustion engine consumes the fuel but the mechanical energy is not used by the drive system. The amount of fuel that is consumed in this time by the engine can potentially be saved if the car is equipped with a Stop-Start system. Start-Stop system automatically...
-
Jan Schmidt dr inż.
People -
Acoustical images of the Gulf of Gdansk
PublicationAcoustic images of seabed are of interest to specialists in the field of marine engineering, marine navigation, marine archeology, hydrogeology, etc. New technolo gies based on use of elastic waves, predominantly acoustic waves that allow detecting complexity of geometric forms of seabed, ensure progress in studying the bathymetric structure of seafloor. Use of parametric sources of waves generated...
-
ALGORYTMY STEROWANIA SILNIKA WYSOKOPRĘŻNEGO Z UKŁADEM COMMON RAIL
PublicationRozwój wiedzy i technologii związanej z procesami spalania paliwa w silniku i prowadzeniem kontrolowanego procesu spalania, skutkuje wzrostem sprawności silników i lepszą ochroną środowiska. Ciekawym rozwiązaniem technicznym jest silnik z zapłonem samoczynnym pracujący z bardzo wysokim ciśnieniem wtrysku paliwa i często z recyrkulacją spalin – silnik z układem Common Rail. Do sterowania silnika stosowane są złożone układy mechatroniczne...
-
Negative carbon dioxide gas power plant integrated with gasification of sewage sludge
PublicationOne of the primary objectives of the negative carbon dioxide gas power plant (nCO2PP) is to develop an innovative technology confirming the possibility of the use of sewage sludge to produce electricity while having a positive impact on the environment. In this paper, a mathematical model is presented to estimate thermodynamic parameters of the system in relation to the gasification process and changes in such parameters in the...
-
BADANIE EFEKTYWNOŚCI WYKRYWANIA ANOMALII PROCESOWYCH W DZIAŁANIU TURBINY PAROWEJ ELEKTROWNI JĄDROWEJ PRZY POMOCY METOD WIELOWYMIAROWEJ ANALIZY STATYSTYCZNEJ
PublicationW artykule przedstawiono analizę możliwości wykrywania anomalii procesowych w działaniu turbiny parowej elektrowni jądrowej przy pomocy metod wielowymiarowej analizy statystycznej. Zasymulowano symptomy dwóch rodzajów uszkodzeń turbiny parowej tj. uderzenie wodne oraz, wyciek pary z zaworu części niskoprężnej. Jako narzędzie diagnostyczne wykorzystano Metodę Składników Podstawowych PCA (z ang. Principal Component Analysis). Jako...
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 1/2
PublicationWind power plants are considered as ecologically-clean source of energy. However, manufacturing processes cannot be treated that way. Manufacturing processes consume huge amount of electrical and thermal energy and significant amount of materials, e.g. steel, polymers, oils and lubricants. All of the above could be potentially harmful for environment. There are not many works and publications regarding life-cycle analysis of wind...
-
M2M communications system proposal for maritime applications
PublicationThis article describes the proposal to use the M2M communication to enhance the safety of people, ships and other marine infrastructure, in broadly defined marine systems. In addition, there are numerous examples of planned solutions to be implemented in the near future as well as new services. The proposal for M2M communication system architecture is described below. In addition, the use of the STRUGA system radio interface as...
-
Advanced Control Structures of Turbo Generator System of Nuclear Power Plant
PublicationIn the paper a synthesis of advanced control structures of turbine and synchronous generator for nuclear power plant working under changing operating conditions (supplied power level) is presented. It is based on the nonlinear models of the steam turbine and synchronous generator cooperating with the power system. Considered control structure consists of multi-regional fuzzy control systems with local linear controllers, including...
-
Advanced Control Structures of Turbo Generator System of Nuclear Power Plant
PublicationIn the paper a synthesis of advanced control structures of turbine and synchronous generator for nuclear power plant working under changing operating conditions (supplied power level) is presented. It is based on the nonlinear models of the steam turbine and synchronous generator cooperating with the power system. Considered control structure consists of multi-regional fuzzy control systems with local linear controllers, including...
-
Determination of probabilities defining safety of a sea-going ship during performance of a transportation task in stormy weather conditions
PublicationThe paper presents the possibility of applying the theory of semi-Markov processes to determine the limiting distribution for the process of changes of technical states being reliability states of the systems of sea-going ships significantly affecting safety of such ships, which include main engine, propeller and steering gear. The distribution concerns the probabilities of occurrence of the said states defined for a long time...
-
Stirling engines - the state of technology development and computational models
PublicationStirling engines represent a technologically important solution in combined heat and power systems. Their use enables the achievement of over 90 percent efficiency in the management of the primary energy source with a very high durability of the device, mainly due to the lack of contact of the working gas with external factors and a very small number of mechanical components. The use of a Stirling engine may be equally important...
-
Domestic ORC micro-CHP combined with a commercial gas boiler
PublicationThe chapter presents the results of experimental studies conducted during the launch of the first in Poland demonstration prototype of the micro ORC coupled to a domestic gas boiler. The accomplished studies indicated the possibility for the ORC module to work with such boiler (autonomous source of heat) with a prototype single-stage axial micro turbine as the expansion machine. Confirmation of that fact has been delineated in...
-
Wind Turbines Modeling as the Tool for Developing Algorithms of Processing their Video Recordings
PublicationIn the real world, many factors exist disturbing observation of the examined phenomena and causing various noises and distortions in recorded signals. It very often makes it difficult or even impossible to optimize various signal processing algorithms, through finding appropriate parameters. In this paper, we show an application, that retrieves wind turbine rotor speed from recorded video. Next, we describe the process of reduction...
-
A commercial gas boiler fitted with the ORC module as perspective solution for households
PublicationIn this paper the applicability of the commercial gas boiler (De Dietrich DTG X23N) coupled with the laboratory prototype micro ORC setup was experimentally studied. The main objective was to determine the working fluid capability to obtain required temperatures of vapour prior to the turbine, attainable heat rates and efficiencies of the whole system. The boiler thermal power was 25 kW. Tests were carried out with a single stage...
-
Wind Turbines Modeling as the Tool for Developing Algorithms of Processing their Video Recordings
PublicationIn the real world, many factors exist disturbing observation of the examined phenomena and causing various noises and distortions in recorded signals. It very often makes it difficult or even impossible to optimize various signal processing algorithms, through finding appropriate parameters. In this paper, we show an application, that retrieves wind turbine rotor speed from recorded video. Next, we describe the process of reduction...
-
Maritime Communications Network Development Using Virtualised Network Slicing of 5G Network
PublicationThe paper presents the review on perspectives of maritime systems development at the context of 5G systems implementation and their main properties. Firstly, 5G systems requirements and principles are discussed, which can be important for maritime applications. Secondly, the problems of network softwarisation, virtualisation and slicing, and possible types of services for potential implementation in 5G marine applications are described....
-
Understanding Fuel Saving and Clean Fuel Strategies Towards Green Maritime
PublicationDue to recent emission-associated regulations imposed on marine fuel, ship owners have been forced to seek alternate fuels, in order to meet the new limits. The aim of achieving low-carbon shipping by the year 2050, has meant that alternative marine fuels, as well as various technological and operational initiatives, need to be taken into account. This article evaluates and examines recent clean fuels and novel clean technologies...
-
IDENTIFICATION OF THE INTERFECE OF LATERAL SLIDE BEARINGS
PublicationIn the paper, the model of slide bearings of motor engine, the metodology of research on this type of bearings and its results are presented measurement standpoint consisting of main elements of Briggs & Stratton 550 serie 10 T 802 model piston motor engine driven by three phase elektric engine is introduced . On the measurement standpoint are measurements were done, needed for specification...
-
Investigating the sustainability, utilisation, consumption and conservation of sea mammals – A systematic review
PublicationAlmost 80 % of the oceans, especially the Arctic and Subarctic are primarily inhabited by marine mammals. Marine species depend mostly on sea ice for food, raising their young ones and safeguarding themselves from predators. Consumption of marine mammals has always been recommended as healthy, but the truth is that it can be detrimental for human health because of sea water pollution from trash and chemicals. This systematic review...
-
ENHANCED MASTER CYCLE - SIGNIFICANT IMPROVEMENT OF STEAM RANKINE CYCLE
PublicationThe present paper focuses on an enhancement of the Master Cycle. In the first part, the paper presents a classical Master Cycle which is a modification of the double reheat Rankine cycle. This modification allows to slightly increase efficiency, resolves problems caused by superheated steam on bleeds and decreases mass flow rate of steam directed to reheat. These improvements include the implementation of a tuning turbine from...
-
AC Motor Voltage and Audible Noise Dataset
PublicationThe dataset titled AC motor voltage and audible noise waveforms in ship’s electrical drive systems with frequency converters contains the voltage and sound measurement results recorded in a marine frequency controlled AC drive system. The dataset is part of research focussing on the impact of the ship’s electrical drive systems with frequency converters on vibrations and the level of audible noise on ships. The dataset allows the...
-
System informacji przestrzennej dla morskich rejonów przybrzeżnych. Logistyka i obronność.
PublicationAutorzy wskazują na możliwość poprawienia jakości zarządzania decyzjami oraz dowodzeniem na wypadek działań wojennych lub wypadków morskich poprzez jednoznaczne i metodyczne połączenie cyfrowych map morskich wykonanych w standardzie ENC/S-57 i DNC/VPF oraz danych z zasobu geodezyjnego dotyczącego obszaru lądowego. Aktualnie nie funkcjonuje w Polsce system informacji przestrzennej obejmujący polskie wybrzeże, który mógłby zostać...
-
Lech Kilian dr inż.
People -
Combined operation of 900MW power plant with the ORC through the bleed steam extraction point and CO2 recovery system
PublicationThe work presented here is aimed at utylisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90 C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach...
-
The efficiency of turbomachinery in the zero-and three-dimensional approaches
PublicationEfficiency of turbomachinery is usually defined using an isentropic process. This approach provides a reliable reference point only when pressure and temperature measurements are available, e.g. at the casing inlet and outlet. In the case of a single stage internal efficiency determination the reference point is difficult. Computational fluid dynamics allows for an exact calculation of values of losses occurring in a turbine...
-
Power enhancement of the Brayton cycle by steam utilization
PublicationThe paper presents thermodynamic analysis of the gas-steam unit of the 65 MWe combined heat and power station. Numerical analyses of the station was performed for the nominal operation conditions determining the Brayton and combined cycle. Furthermore, steam utilization for the gas turbine propulsion in the Cheng cycle was analysed. In the considered modernization, steam generated in the heat recovery steam generator unit is directed...
-
A new method of wind farm active power curve estimation based on statistical approach
PublicationThe purpose of this paper is to solve the wind farm active power estimation problem, introducing the method which is based on a statistical approach and robust fitting. The proposed algorithm uses a statistical approach and compared to existing ones- includes a wind direction as well as the influence of turbine start-up procedure on the estimation. The results show that additional estimation inputs i.e. the wind direction and the...
-
Projekt stanowiska badawczego do wyznaczania charakterystyki ogólnej silnika spalinowego ZS przy wykorzystaniu hydraulicznego układu odbioru mocy
PublicationPrzedstawiono projekt stanowiska badawczego służącego do wyznaczania charakterystyki ogólnej silnika pojazdu ciężarowego, wykorzystując przystawkę odbioru mocy do napędu układu hydraulicznego generującego obciążenie silnika w różnych punktach jego pracy. Przedstawiono założenia projektowe oraz ograniczenia konstrukcyjne. Omówiono zasadę działania stanowiska i metodę wyznaczania charakterystyki. Opisano układ hydrauliczny oraz układ...
-
Aleksander Schmidt mgr inż.
People -
Heavy duty vehicle fuel consumption modelling using artificial neural networks
PublicationIn this paper an artificial neural network (ANN) approach to modelling fuel consumption of heavy duty vehicles is presented. The proposed method uses easy accessible data collected via CAN bus of the truck. As a benchmark a conventional method, which is based on polynomial regression model, is used. The fuel consumption is measured in two different tests, performed by using a unique test bench to apply the load to the engine. Firstly,...
-
Jacek Tomków dr hab. inż.
PeopleEducation:1. 2018 - Ph.D. of Technical Sciencesin field of Materials Engineeringthesis: Influence of underwater welding conditions on cold cracking of high strength low alloy steel 2. 2012 - Master of Science Engineer, Gdansk University of Technologyin the field of: Mechanical Engineeringwith specialization in: Manufacturing Engineering and Computer Aided Manufacturing Processesthesis: Non-destructive testing of welding joints...
-
Modelling the impact of the agricultural holdings and land-use structure on the quality of inland and coastal waters with an innovative and interdisciplinary toolkit
PublicationThe changes taking place in the marine coastal zones are extremely important, as about 40% of the human population currently lives in the coastal areas (within 100 kilometres of the coastline) increasing anthropogenic pressure on the marine ecosystems. Agriculture is a significant source of nutrients to the marine environment that increase hypoxia, eutrophication and may pose a threat to the services provided by ecosystems. In...
-
Opinia na okoliczność wykonania (prawidłowego lub nie, w części lub całości ) umowy 01/11/2010 dotyczącej remontu statku m/v „AKERO” w sprawie z powództwa Quadrant Marine Consultancy Sp. z o.o. przeciwko Northwind Shipping A.S. w Enebakk, Norwegia
PublicationOpinia na temat prawidłowości (nieprawidłowości) przebiegu remontu statku M/V Akero (później M/V North Wind), wydana na zlecenie Sądu Okręgowego w Gdańsku. Opinię sporządzono na podstawie akt sprawy IXGC 14/12.