Filters
total: 6097
displaying 1000 best results Help
Search results for: RISK, INVESTMENT PROCESS
-
Instrumented end notched flexure - Crack propagation and process zonemonitoring Part II: Data reduction and experimental
PublicationA mode II instrumented end notched flexure three point bending (ENF) adhesion test is described. The adhesive joint consists of two aluminium alloy (AW7075-T6) plates bonded with a structural epoxy adhesive (Hysol EA 9395™). Strain gauges are attached to the outer surface (backface) of the substrates in the lengthwise direction to measure local surface strain during crack propagation. Simultaneously, load/displacement measurements...
-
Removal of Siloxanes from Model Biogas by Means of Deep Eutectic Solvents in Absorption Process
PublicationThe paper presents the screening of 20 deep eutectic solvents (DESs) composed of tetrapropylammonium bromide (TPABr) and glycols in various molar ratios, and 6 conventional solvents as absorbents for removal of siloxanes from model biogas stream. The screening was achieved using the conductor-like screening model for real solvents (COSMO-RS) based on the comparison of siloxane solubility in DESs. For the DES which was characterized...
-
Monitoring of n-butanol vapors biofiltration process using an electronic nose combined with calibration models
PublicationMalodours, by definition, are generally unpleasant, nuisance smells that are a mixture of volatile chemical compounds which can be perceptible even at low concentrations. Due to the more frequent occurrence of odour nuisance associated with the odour sensations, and thus the need to remove them from the air, deodorization techniques are commonly used. Biofiltration is one of the methods of reducing odorants in the air stream. In...
-
Spectroscopic studies of a ring opening process between epoxy- and aminosilanes and imine formation reactions in aqueous solutions
PublicationNMR and Raman spectroscopy studies were performed for different 3-aminopropyl(trimethoxy)- and 3-glycidoxypropyl (trimethoxy)silane based sol-gel systems containing different ketones. Exceptionally stable imine products were obtained depending on a reaction system at alkaline pH conditions and in the presence of water. These imine formation reactions were carried out without further catalyst. In addition, effect of water for the...
-
Effect of some organic solvent - water mixtures composion on precipitated calcium carbonate in carbonation process
PublicationPrecipitated calcium carbonate particles were obtained during carbonation of calcium hydroxide slurry with carbon dioxide. Aqueous solutions of isopropyl alcohol, n-butanol and glycerol were used as solvents. Concentration of organic additives in the reactive mixture was from 0 to 20 % (vol.). Precipitation process were performed in a stirred tank reactor equipped with gas distributor. Multimodal courses of particles size distribution...
-
The impact of hydrological research, municipal authorities, and residents on rainwater management in Gdańsk (Poland) in the process of adapting the city to climate change
PublicationAim of the study The city of Gdańsk faces changing climatic conditions that result in a higher frequency of extreme weather events. In response to the increasingly frequent appearance of flash floods, scientific research was carried out on changes in the probability of the occurrence of maximum daily precipitation in Gdańsk. The purpose of this paper is to show the role of hydrological research (science), decisions of local authorities...
-
Coda wave interferometry in monitoring the fracture process of concrete beams under bending test
PublicationEarly detection of damage is necessary for the safe and reliable use of civil engineering structures made of concrete. Recently, the identification of micro-cracks in concrete has become an area of growing interest, especially using wave-based techniques. In this paper, a non-destructive testing approach for the characterization of the fracture process was presented. Experimental tests were made on concrete beams subjected to mechanical...
-
Assessing ecotoxicity, synergic and antagonistic actions of commonly used components of polymerization mixture in molecularly imprinted polymers preparation process
PublicationIncreasingly, the challenge is the optimal process of developing a suitable MIP-type sorptive material (taking into account its final form and application area), which is mainly related to the efficiency/effectiveness of the polymerization process. The lack of reaction or its low efficiency generates additional waste and puts it into the environmental cycle. The main aim of the performed research was the estimation of ecotoxicity,...
-
Safety integrity level verification for safety-related functions with security aspects
PublicationThe article is devoted some important issues of the functional safety analysis, in particular the safetyintegrity level (SIL) verification of safety functions to be implemented within the distributed controland protection systems with regard to cyber security aspects. The procedure for functional safety man-agement includes hazard identification, risk analysis and assessment, specification of overall safetyrequirements and definition...
-
Assessment of the devulcanization process of EPDM waste from roofing systems by combined thermomechanical/microwave procedures
PublicationEthylene-propylene-diene rubber (EPDM) is a elastomer widely used in common industrial applications. EPDM can be shaped into sheets and employed as isolating material for roofing systems. In this study, scraps of EPDM from commercial, industrial and residential roofing systems were treated by combined thermo-mechanical and microwave devulcanization processes including peroxide of benzoyl (BPO). The devulcanized EPDM (Dev-EPDM)...
-
The clamping selection method to reduce the vibration of large-size workpieces during the face milling process
PublicationThe article introduces a method for selecting the best clamping conditions to obtain vibration reduction during milling of large-size workpiece. It is based on experimental modal analysis performed for a set of assumed, fixing conditions of a considered workpiece to identify Frequency Response Functions (FRFs) for each tightening torque of the mounting screws. Simulated plots of periodically changing nominal cutting forces are...
-
Journal of Property Investment & Finance
Journals -
Influence of process of straightening ship hull structure made of 316L stainless steel on corrosion resistance and mechanical properties
PublicationThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries, for architectural elements, and many others. The chemical composition of corrosion-resistant...
-
Denitrification Process Enhancement and Diversity of the Denitrifying Community in the Full Scale Activated Sludge System after Adaptation to Fusel Oil
PublicationImplementation of anaerobic digestion of primary sludge in modern wastewater treatment plants (WWTPs) limits the availability of organic carbon for denitrification in conventional nitrification-denitrification (N/DN) systems. In order to ensure efficient denitrification, dosage of the external carbon source is commonly undertaken. However, application of commercial products, such us ethanol or acetate, greatly increases operational...
-
Influence of reduction process on the structural and mechanical properties of (Pb,Bi)-(Si,Ge)-O oxide glasses
PublicationThe effect of the reduction process in H2 at 380 °C on the microstructure and elemental composition of a glass Bi0.4Pb0.2Si0.4Ox has been investigated. It has been shown that after reduction a clearly separated top layer with a thickness of approx. 50 µm was formed on the surface of the sample. This layer is depleted of oxygen and has higher electrical conductivity than the interior of the glass. It has also been found that some...
-
Virtual Engineering Object / Virtual Engineering Process: A specialized form of Cyber Physical System for Industrie 4.0
PublicationThis paper reviews the theories, parallels and variances between Virtual Engineering Object (VEO) / Virtual Engineering Process (VEP) and Cyber Physical System (CPS). VEO and VEP is an experience based knowledge representation of engineering objects and processes respectively. Cyber–physical systems (CPSs) are the next generation of engineered systems in which computing, communication, and control technologies are tightly integrated....
-
Automation of the Road Gate Operations Process at the Container Terminal—A Case Study of DCT Gdańsk SA
PublicationThe future increased terminal capacity will result in more container movement through the road complex and rail siding, which are one of the most critical areas (potential bottlenecks) in the container terminal. Truck turnaround time is one of the major factors that customers take into account while deciding how many container volumes they will handle through the container terminal. To enable to optimize increased traffic with...
-
Influence of Fragment Size on the Time and Temperature of Ethylene Vinyl Acetate Lamination Decomposition in the Photovoltaic Module Recycling Process
PublicationPhotovoltaics is a commercially available and reliable technology with significant potential for long-term growth in nearly all global regions. Several research institutes and companies are working on recycling concepts for thin film modules and modules with crystalline cells. The establishment of recycling and reuse technologies appropriate and applicable to all photovoltaics (PV) modules is a key issue to be addressed as part...
-
Experimental investigation and process parameter optimization of sheet metal bending by line heating method
PublicationThe present study is concerned with the experimental investigation of sheet metal deforming by line heating method that incorporates the combined effect of traverse speed of the torch, thickness of the sheet metal, and the number of passes of the torch. For the numerical analysis of metal bending by line heating, the
-
The variant allele of the rs188140481 polymorphism confers a moderate increase in the risk of prostate cancer in Polish men
Publication -
Model of identification of events and accident scenarios for a method of risk and safety assessment of ships in damaged conditions
PublicationW pracy opisano podstawowe problemy związane z identyfikacją zdarzeń i scenariuszy wypadku oraz modelowaniem ryzyka dla alternatywnej metody oceny bezpieczeństwa statków w stanie uszkodzonym. Zastosowano podejście do bezpieczeństwa statków oparte na ocenie zachowania się statku i ocenie ryzyka wypadku. Wskazano możliwości zastosowania modelowania do analizy bezpieczeństwa statków na etapie projektowania, w czasie eksploatacji i...
-
Human Health Risk Assessment on the Consumption of Apples Growing in Urbanized Areas: Case of Kharkiv, Ukraine
Publication -
Risk factors of depressive and anxiety symptoms 8 years after coronary artery bypass grafting
Publication -
Telomere Length and Risk of Major Adverse Cardiac Events and Cancer in Obstructive Sleep Apnea Patients
Publication -
Reference intervals for common carotid intima-media thickness measured with echotracking: relation with risk factors
Publication -
Daytime, home and office blood pressures in treated hypertensive patients according to accretion of cardiovascular risk
Publication -
A Method of Risk and Safety Assessment During the Ship Salvage Using the Hazard, Release and Consequence Analysis
Publication -
Financial performance under influence of credit risk in non-financial firms: evidence from Pakistan
Publication -
COVID-19-Associated Mucormycosis (CAM): Case-Series and Global Analysis of Mortality Risk Factors
Publication -
Associations of Nutritional Behavior and Gut Microbiota with the Risk of COVID-19 in Healthy Young Adults in Poland
Publication -
The Risk Indicators of Construction Projects’ Cost Overruns Assessed with PCA, Decision Trees, and Pearson’s Correlations
Publication -
Inhalation risk to PAHs and BTEX during barbecuing: The role of fuel/food type and route of exposure
Publication -
Cardiovascular risk and response to lipid lowering therapy in patients with HIV infection according to different recommendations
Publication -
The Assessment of Risk and Predictors of Sleep Disorders in Patients with Psoriasis—A Questionnaire-Based Cross-Sectional Analysis
Publication -
The Level of FGF 21 as a New Risk Factor for the Occurrence of Cardiometabolic Disorders amongst the Psoriatic Patients
Publication -
Patient rights, risk, and responsibilities in the genetic era – a right to know, a right not to know, or a duty to know?
Publication -
Cold Start Emissions of Spark-Ignition Engines at Low Ambient Temperatures as an Air Quality Risk
Publication -
In vitro to in vivo extrapolation to support the development of the next generation risk assessment (NGRA) strategy for nanomaterials
Publication -
PCDDs, PCDFs and PCBs in locally produced foods as health risk factors in Silesia Province, Poland
Publication -
Optical method supported by machine learning for urinary tract infection detection and urosepsis risk assessment
PublicationThe study presents an optical method supported by machine learning for discriminating urinary tract infections from an infection capable of causing urosepsis. The method comprises spectra of spectroscopy measurement of artificial urine samples with bacteria from solid cultures of clinical E. coli strains. To provide a reliable classification of results assistance of 27 algorithms was tested. We proved that is possible to obtain...
-
Problem of optimal load distribution between generators minimizing risk of enegretic ship system overload.
PublicationOmówiono system rozdziału mocy czynnych pomiędzy generatorami w systemie energetycznym statku. Minimalizuje się ryzyko przeciążeń systemu przy jednoczesnej minimalizacji kosztów wytwarzania energii w systemie.
-
Surface Roughness Evaluation in Thin EN AW-6086-T6 Alloy Plates after Face Milling Process with Different Strategies
PublicationLightweight alloys made from aluminium are used to manufacture cars, trains and planes. The main parts most often manufactured from thin sheets requiring the use of milling in the manufacturing process are front panels for control systems, housing parts for electrical and electronic components. As a result of the final phase of the manufacturing process, cold rolling, residual stresses remain in the surface layers, which can influence...
-
Mechanochemically synthesized Mn3O4@β-cyclodextrin mediates efficient electron transfer process for peroxymonosulfate activation
PublicationThe rational surface engineering of heterogeneous catalysts is of great significance in advanced oxidation processes (AOPs) for eliminating refractory contaminants but remains challenging. In this study, β-cyclodextrin modified Mn3O4 (Mn3O4@β-CD) was prepared through a mechanochemical approach for peroxymonosulfate (PMS) activation, which achieved efficient bisphenol A (BPA) removal via electron transfer process (ETP). The reactive...
-
SEMG signal database for the automated upper limb rehabilitation process
Open Research DataAn automated rehabilitation device control system requires information about the patient's physiological condition. This is possible thanks to the use of biological feedback in the form of electromyography and surface signals (Surface Electromyography, SEMG).
-
STRUCTURE AND MAGNETIC PROPERTIES OF Bi5Ti3FeO15 CERAMICS PREPARED BY SINTERING, MECHANICAL ACTIVATION AND EDAMM PROCESS. A COMPARATIVE STUDY
PublicationThree different methods were used to obtain Bi5Ti3FeO15 ceramics, i.e. solid-state sintering, mechanical activation (MA) with subsequent thermal treatment, and electrical discharge assisted mechanical milling (EDAMM). The structure and magnetic properties of produced Bi5Ti3FeO15 samples were characterized using X-ray diffraction and Mössbauer spectroscopy. The purest Bi5Ti3FeO15 ceramics was obtained by standard solid-state sintering...
-
Influence of selected CO2 absorption promoters on the characteristics of calcium carbonate particles produced by carbonation of the post-distillation liquid from the Solvay process
PublicationThe aim of this work is to compare the effect of selected process parameters, gas flow rate, CO2 absorption promoter concentration and its pKa, on the precipitation of CaCO3 by the gas-liquid method using a model post-distillation liquid from the Solvay process. To ensure effective capture of CO2, the absorption promoters used were ammonia, triethanolamine and triethylamine. The Box-Behnken Design was applied to plan the experiments....
-
Georisk-Assessment and Management of Risk for Engineered Systems and Geohazards
Journals -
The Staged Combustion of Meat-and-Bone Meal:The Characteristics of Conversion Sub-processes and Large-Scale Process Outputs
Publicationt Organic waste has been playing an increasingly important role in the energy market as those that may support the economies in pursuing towards decarbonization by increasing the share of renewables in the overall energy balance. In this group of alternative fuels, meat-and-bone meals being a post-production waste of the steadily developing meat industry, constitute a considerable proportion. Though they are rich in minerals, their...
-
The effect of beech wood (Fagus sylvatica L.) steaming process on the colour change versus depth of tested wood layer
PublicationThe results of experimental research on the colour changes of beech wood at different depths of the tested layer are presented. Beech wood (Fagus sylvatica L.) dried in a conventional kiln was tested. Half of the wood samples were steamed prior to the drying process. Colour changes were measured at various depths after the face milling process was used to remove the material to expose to the deeper surface. The colour changes were...
-
The influence of different glycerine purities on chemical recycling process of polyurethane waste and resulting semi‐products
PublicationChemical recycling is the most favourable recycling method due to the possibility of polyol recovery. This work is dedicatedto the utilisation of crude glycerine and polyurethane waste. It aims at determining the impact of the use of glycerine fromthe production of biodiesel with various degrees of purity as a cleavage agent on the decomposition process of polyurethanefoam. The influence of glycerine purit y on the chemical structure...