Search
Filters
total: 512
Search results for: connection control
-
Determination of flow properties of a serial connection of two pneumatic elements with (C=2.4, b=0.26) and (C=2.0, b=0.11) from changes in air pressure in a tank being emptied
Open Research DataThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for two directional control valves arranged in-line. Four test configurations were used: (1) being emptied tank -> the first DCV -> ambient atmosphere, (2) being emptied...
-
Determination of flow properties of a serial connection of two pneumatic elements with (C=2.4, b=0.26) and (C=5.7, b=0.32) from changes in air pressure in a tank being emptied
Open Research DataThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for two directional control valves arranged in-line. Four test configurations were used: (1) being emptied tank -> the first DCV -> ambient atmosphere, (2) being emptied...
-
Determination of flow properties of a serial connection of two pneumatic elements with (C=2.8, b=0.25) and (C=5.7, b=0.32) from changes in air pressure in a tank being emptied
Open Research DataThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for two directional control valves arranged in-line. Four test configurations were used: (1) being emptied tank -> the first DCV -> ambient atmosphere, (2) being emptied...
-
Determination of flow properties of a serial connection of two pneumatic elements with (C=2.4, b=0.26) and (C=5.5, b=0.37) from changes in air pressure in a tank being emptied
Open Research DataThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for two directional control valves arranged in-line. Four test configurations were used: (1) being emptied tank -> the first DCV -> ambient atmosphere, (2) being emptied...
-
Determination of flow properties of a serial connection of two pneumatic elements with (C=2.4, b=0.26) and (C=2.8, b=0.25) from changes in air pressure in a tank being emptied
Open Research DataThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for two directional control valves arranged in-line. Four test configurations were used: (1) being emptied tank -> the first DCV -> ambient atmosphere, (2) being emptied...
-
Dual drive control under SVPWM, experimental results
Open Research DataThe dataset contains the experimental results of the project: A universal algorithm of space vector pulse width modulation for three-level three and multi-phase NPC inverters with DC-link voltage balancing. The analysis includes the behaviour of the drive system, examining the dynamic system response to speed and angle changes, and encompassing data...
-
Extensions of ETSI performance measurements methodology for statistical results analysis =Rozszerzenia metodologii pomiarów wydajności zaproponowanej przez ETSI przy statystycznej analizy wyników
PublicationNext Generation Network (NGN) architecture was proposed by International Telecommunication Union Telecommunication Standardization Sector (ITU-T) to deliver telecommunication services satisfying the needs of modern society for an access to information. The core of NGN service stratum are IP Multimedia Subsystem (IMS) elements acting as service controls units. To assess performance of IMS components, European Telecommunications...
-
Sustainable Waste Management for Implementation of a Circular Economy Model in a Port
PublicationThe manuscript presents the management of waste from marine vessels and cargo handling companies in a selected European Union port. The main objective of the paper is to analyse and evaluate the existing waste management model in the port of Szczecin in the context of circular economy. The expert research carried out is aimed, inter alia, at identifying which of the solutions currently in use need to be improved from an environmental...
-
Jakość usług w optycznej sieci wielodomenowej z hierarchiczną strukturą płaszczyzn sterowania
PublicationW rozprawie przedstawiono przegląd architektur sieci z gwarancją jakości klas usług oraz stan prac w zakresie realizacji optycznych sieci ASON, GMPLS oraz ASON/GMPLS. Opisano wymagania i zaawansowanie prac w realizacji sieci ASON/GMPLS z hierarchiczną strukturą płaszczyzn sterowania oraz problemy związane z zagadnieniem jakości klas usług w tej sieci. Zaprezentowano założenia, koncepcję oraz realizację modelu symulacyjnego optycznej...
-
Modyfikacja połączenia dźwigara ze słupem w konstrukcji stalowej Terminalu T2 Portu Lotniczego w Gdańsku
PublicationW2015 r. ukończono rozbudowę Terminalu T2 Portu Lotniczego im. Lecha Wałęsy wGdańsku. Politechnika Gdańska pełniła nadzór naukowy nad rozbudową obiektu. Wykonano wiele analiz, których celem była weryfikacja pracy konstrukcji w fazach montażu oraz w stanie docelowym. Wnioski z przeprowadzonych badań doprowadziły do modyfikacji oparcia dźwigarów dachowych na stalowych słupach nośnych, z uwagi na stwierdzone lokalne przekroczenia...
-
Partially Isolated Multi-Active Bridge DC-DC Converter with Bidirectional EV Charging Ports
PublicationThere is a growing interest in multiport converters due to their ability to interconnect various energy sources and loads using reduced number of components. Regarding electric vehicle (EV) chargers connection, existing multiport solutions either lack scalability, featuring only one isolated charging port or the operation of ports depend on each other, complicating the converter control algorithm. This article proposes a partially...
-
Zaawansowany układ samoczynnego załączania rezerwy oparty na sterowniku WAGO PFC200
PublicationArtykuł opisuje projekt i wykonanie układu samoczynnego załączania rezerwy (SZR) na potrzeby stacji elektroenergetycznej Laboratorium LINTE^2 na Politechnice Gdańskiej. Układ SZR został zbudowany na podstawie modułowego sterownika PLC WAGO PFC200. W artykule omówiono zasadę działania układu, a także jego program sterowania i aplikację panelu HMI, opracowane w zintegrowanym środowisku programistycznym CoDeSys 3.5. Oprócz zadań typowego...
-
Hydraulic potential of the Lower Vistula (Poland)
PublicationThe Vistula is the largest river in Poland. Lower Vistula (part of the river discussed in this paper) is almost four hundred kilometers long river section extending from the tributary Narew to the outflow to the Baltic Sea. In the 17th century the Vistula was the most navigable river in Europe. After partitioning of Poland the Vistula lost its significance. Now the Lower Vistula should provide a navigation connection to the Europe...
-
Mechanical properties of single V2O5 nanocrystal - nanoindentation measurement in control of the max-load
Open Research DataThe DataSet contains the nanoindentation curves (indentation force Fn vs penetrationPd) for a single V2O5 nanocrystal supported on a substrate. The measurements were performed in control of the maximum load of Berkovich indenter force from 2 to 50 mN.
-
Mechanical properties of single V2O5 nanocrystal - nanoindentation measurement in control of the max-depth
Open Research DataThe DataSet contains the nanoindentation curves (indentation force Fn vs penetrationPd) for a single V2O5 nanocrystal supported on a substrate. The measurements were performed in control of the maximum depth of Berkovich indenter penetration: 60, 70, and 100 nm.
-
Lack of control over work and organizational citizenship behavior: overwork climate as a suppressor variable
Open Research DataThis study investigates a suppressor effect in the relationship between lack of control over work and organizational citizenship behavior (OCB). Suppressor effects operate when the addition of a predictor (in our study it is an overwork climate) increases the predictive power of another variable (lack of control over work) in predicting an outcome variable...
-
Embedded gas sensing setup for air samples analysis
PublicationThis paper describes a measurement setup (eNose) designed to analyze air samples containing various volatile organic compounds (VOCs). The setup utilizes a set of resistive gas sensors of divergent gas selectivity and sensitivity. Some of the applied sensors are commercially available and were proposed recently to reduce their consumed energy. The sensors detect various VOCs at sensitivities determined by metal oxide sensors’ technology...
-
Closed Form Constraint Equations Used to Express Frictionless Slip of Multibody Systems Attached to Finite Elements—Application to a Contact between a Double Pendulum and a Beam
PublicationThis paper focuses on the numerical modeling of the dynamics of mechanical systems. Robots that can inspect high-voltage lines inspired this research. Their control systems must anticipate potential grab positions appropriately. We intend to formulate equations dedicated to the numerical description of the robot/cable contact. The investigated problem is not straightforward, since parts of the modeled systems are numerically inhomogeneous....
-
Impact of new, navigable canal through the Vistula spit on the hydrologic balance of the Vistula lagoon (Baltic Sea)
PublicationThe object of research - the Vistula Lagoon is one of the two lagoons on the Polish coast, which is of great importance not only from an economic point of view, but also an environmental one. The purpose of the paper is to provide calculations on the current water balance for the Vistula Lagoon, before and after construction of a canal through the Vistula Spit. This is important because the construction of a new connection between...
-
Advanced ultra super critical power plants: role of buttering layer
PublicationDissimilar metal welded (DMW) joint plays a crucial role in constructing and maintaining ultra-supercritical (USC) nuclear power plants while presenting noteworthy environmental implications. This research examines different welding techniques utilized in DMWJ, specifically emphasizing materials such as P91. The study investigates the mechanical properties of these materials, the impact of alloying elements, the notable difficulties...
-
Review of non- welded piping technologies on offshore equipment projects
PublicationThe aim of this article are considerations on welded and non-welded tube connection technologies, with advantages and disadvantages of both. After choosing non-welded solutions as the assembly method of choice, the thesis progresses to describing the most widely-used tube connection technologies (JIC, Ermeto, retain ring flanges, flared tube flanges and other, minor, solutions) and their properties.
-
Enhancing seismic performance of rigid and semi-rigid connections equipped with SMA bolts incorporating nonlinear soil-structure interaction
PublicationNowadays, using smart connections can improve the performance of buildings with some recentering features that are from the superelastic behavior of Shape Memory Alloys (SMAs). It seems that there is different rigidity between the designed connection and the real one in Steel Moment-Resisting Frames (SMRFs), which can be considered as a problematic issue due to the importance of connections in seismic performance assessment. This...
-
Influence of Property Division on the Technical Condition of a Building
PublicationIn this article, the correlation between a technical condition of a building and property division is analyzed and assessed. In the course of the usage of a building, the process of its degradation and the increase in the demands of property occupants can be observed. There is a direct connection between the difficult technical condition of a building and the fragmentation of the ownership structure. Although not considered in...
-
Cross-border transmission line configuration influence on the electrical power and energy billing process
PublicationIn 2015 a connection between the Polish and Lithuanian power systems become fully operational. The connection consists of a 400 kV double circuit transmission line and a back-to-back HVDC substation located on the Lithuanian side. A magnetic couplings between the circuits of the transmission line cause that during power transmission a different values of active power losses are observed in both circuits. This situation may cause...
-
Do We Need a Lighting Detox for Sustainable Cities in the 21st Century?
PublicationThis article looks at relearning our connection to light and dark in context of sustainability, climate change and urban lighting.
-
Quality measure of VoIP services in carrier grade systems
PublicationThis paper describes passive measurement method of VoIP services quality in carrier grade systems, engaging slight system resources. Measurement is based on analyzing quality information in sender and receiver reports in RTCP packets sent by the end points of RTP session. Data is analyzed and stored by Session Boarder Controllers SBC. Objective evaluation of VoIP calls is based on quality information of IP connection and voice...
-
Estimation of a single balun parameters on the base of back-to-back measurements
PublicationA method of estimation of a single balun S parameters based on the measured parameters of back-to-back configuration is presented in the paper. Proposed approach is to measure two back-to-back circuits: i) direct connection of baluns and ii) connection with additional transmission line segment between the baluns. Coupling effects in both circuits are calculated from full-wave simulations. Next they are applied to estimate the parameters...
-
Opinion about causes of framing of Kingston chest (box cooler) damage, on PSV vessel VS4411 DF-PSV (B-855)
PublicationThe subject of analysis is a damage of welded connection of box cooler framing segments, made as separate bars 50mm thickness, connected by the welds in corners. Studies of documents delivered by Customer shows cracks on the fusion of filet welds and twisting of box cooler frame. The subject of analysis is a damage of welded connection of box cooler framing segments, made as separate bars 50mm thickness, connected by the welds...
-
Research on assessment of bolted joint state using elastic wave propagation
PublicationThe work contains results of experimental investigation of elastic wave propagation in a bolted single-lap joint. Tests were carried out for the excitation perpendicular to the connection plane. In experimental studies, PZT transducers were used for both excitation and registration of ultrasonic waves. The analyses took into account varying contact conditions between the elements of the connection depending on the value of the...
-
Chosen aspects of skeletal system modeling: Numerical solid and shell models of femur part
PublicationThe purpose of this paper is to present a new method of femur part modeling by using the finite element method. This method treats a femur part as a system composed of cortical and trabecular bone. For the purpose of determining a proper shape of femur part model there were created three models: a) the first one describes a femur part as a solid structure; b) the second one describes a femur part as a connection of cortical bone...
-
Modelling the malware propagation in mobile computer devices
PublicationNowadays malware is a major threat to the security of cyber activities. The rapid develop- ment of the Internet and the progressive implementation of the Internet of Things (IoT) increase the security needs of networks. This research presents a theoretical model of malware propagation for mobile computer devices. It is based on the susceptible-exposed- infected-recovered-susceptible (SEIRS) epidemic model. The scheme is based on...
-
Throughput-Coverage Characteristics for Soft and Partial Frequency Reuse in the LTE Downlink
PublicationThe paper presents results of simulation and evaluation of throughput-coverage characteristics for the OFDMA-based LTE network with Soft Frequency Reuse or Partial Frequency Reuse. Firstly, simulation results of throughput characteristics for a single user connection are presented, which allow the evaluation of the stability and availability of bit rate achieved in different areas of a cell. Secondly, the capacity characteristics...
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublicationAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
Orthotropic membrane as a mechanical model of surgical implant in abdominal hernia repair
PublicationEven though the incisional hernia repair surgery is a well known procedure, mechanical properties of the tissue-implant system are unknown so the implantation of the repairing mesh is quite intuitive and, recurrences of the illness still take place. The main objective of the study is to define an operated hernia model that can be used for surgery planning and the assessment of the repair persistence. The load applied to the structure...
-
Bearing Capacity of aluminum bars with built-up cross section and glued or welded connections
PublicationThe paper is focused on numerical analysis and experimental test of aluminum bars with glued and welded connections between separate members. The connection properties were tested experimentally. The numerical analysis were conducted for the beam and shell model of the structure. The shape and magnitude of initial geometric imperfection was taken into account
-
Historical carpentry corner log joints—Numerical analysis within stochastic framework
PublicationThe paper presents the results of numerical analysis performed on historical, traditional carpentry corner logjoints of two basic topologies: the short-corner dovetail connection and the saddle notch connection. These types of carpentry joints are commonly used in currently preserved objects of wooden architecture. All connections have been modelled in pinewood, which has been defined in the Finite Element software MSC.Marc/Mentat...
-
Simulation model for evaluation of packet sequence changed order of stream in DiffServ network
PublicationCurrent packet networks use a large variety of mechanisms which should support QoS (Quality of Service). One of those mechanisms is routing (calculating connection paths for incoming service requests). The most effective mechanism in QoS context is dynamic routing, which is based on the current network state described by the offered traffic matrix and link states. After switching between calculated available paths, connection...
-
Pitch estimation of narrowband-filtered speech signal using instantaneous complex frequency
PublicationIn this paper we propose a novel method of pitch estimation, based on instantaneous complex frequency (ICF). New iterative algorithm for analysis of ICF of speech signal in presented. Obtained results are compared with commonly used methods to prove its accuracy and connection between ICF and pitch, particularly for narrowband-filtered speech signal.
-
Pitch estimation of narrowband-filtered speech signal using instantaneous complex frequency
PublicationIn this paper we propose a novel method of pitch estimation, based on instantaneous complex frequency (ICF). New iterative algorithm for analysis of ICF of speech signal in presented. Obtained results are compared with commonly used methods to prove its accuracy and connection between ICF and pitch, particularly for narrowband-filtered speech signal.
-
UKŁAD PRZENIESIENIA NAPĘDU TURBINY WIATROWEJ
PublicationIn a most commonly met design of a wind turbine the power is transmitted from the rotor to the generator through the system composed of the main shaft, friction connection, multiplicating gearbox and a flexible coupling. The driving system comprises almost a complete set of the machine elements being described during machine design lectures and can serve as an interesting illustration of the lectures.
-
Drivetrain of a Wind Turbine
PublicationIn a most commonly met design of a wind turbine the power is transmitted from the rotor to the generator through the system composed of the main shaft, friction connection, multiplying gearbox and a flexible coupling. The driving system comprises almost a complete set of the machine elements being described during machine design lectures and can serve as an interesting illustration...
-
Radar technique in application of interlayer identification connections
PublicationOne of important issues in pavement construction is to ensure that layers applied directly one on top of the other make up a continuous whole and form an integral construction complex. An appropriate interlayer connection plays here significant role ensuring proper transmission of distortions generated by wheels of vehicles to lower layers and preventing water penetration between the layers. In case of damaged pavements where lack...
-
Investigation of some magnetospheric phenomena of geomagnetic storm on March 17, 2013 based on observations from GNSS and NOAA-15 satellite
PublicationSubstantial variations of magnetospheric electron fluxes of low and intermediate energies at an altitude of ~ 800 km at different phases of the geomagnetic storm were investigated. The ionosphere and plasmasphere response was analyzed using TEC variation maps over the Central Europe. A concept of the connection of TEC variations above the Central Europe and spatially inhomogeneous fluxes of energetic particles is being proposed.
-
Stress analysis of the bridge hangers in terms of the fatigue verification
PublicationThe paper presents the results of numerical stress analysis of the bridge rod hangers. Two types of hangers were taken into account, i.e. the bolted hanger and the welded hanger. A detailed FEM shell models of the connection area between the hanger and the bridge span have been developed. Local stress concentration effects have been investigated in terms of fatigue verification.
-
Miniaturized Metal-Mountable U-shaped Inductive-Coupling-Fed UHF RFID Tag Antenna with Defected Microstrip Surface
PublicationThis study presents a novel miniature ultra-high frequency (UHF) radio frequency identification (RFID) tag for metallic objects. Its arrangement includes a U-shaped feeder, which is inductively coupled to two E-type connected patches. Size reduction is achieved by means of utilizing the U-shaped feeder, and introducing a defection in the connection between the two E-type patches. The defection in the connection area between the...
-
Hydrodynamic Model of the New Waterway through the Vistula Spit
PublicationThe decision to build a new waterway (strait) in the Polish part of the Vistula Spit was made in 2017. The new connection between the Gulf of Gdańsk and the Vistula Lagoon is planned as an artificial navigable channel with a lock and a small port. During storm surges and wind tides in the gulf or in the lagoon, sluicing will be re-quired for vessels to tackle the Vistula Spit. This procedure does not require significant water flow...
-
Systemy Smart Cities - studium przypadku
PublicationThe paper presents the architecture of an enterprise service bus used in the construction of information systems processing large amounts of data for decision-making needs at the City Hall in Gdańsk. The key concept of processes of bus development involves installation of developing environment, database connection, flow mechanisms and data presentation. The issue was supported by models such as KPI (Key Processes Identifier) and...
-
SYNTHESIS OF PHOSPHORUS TACRINE ANALOGUES AS A NEW POTENTIAL ANTI-ALZHEIMER’S DISEASE AGENTS
PublicationA series of novel phosphorus tacrine derivatives was obtained in three steps, including synthesis of 9-chlorotacrine, connection of 9-chlorotacrine with hexamethylenediamine, 1,8-diaminooctane and 1,12-diaminododecane linkers and reaction of obtained tacrine diamine analogues with corresponding acid ester to give nine tacrine organophosphorus compounds. All of the obtained final structures were characterized by 1H NMR, 13C NMR,...
-
Strength testing machine results
Open Research DataThe aim of the research project is to determine the rotational stiffness of the connection between the purlin and the part of the truss top chord. The attached files are referred to the forces and displacements obtained from the strength testing machine (two sensors). The 16 specimens were tested on the experimental set up.
-
Inclinometers results
Open Research DataThe aim of the research project is to determine the rotational stiffness of the connection between the purlin and the part of the truss top chord. The attached files are referred to inclinometers results (four devices, two axis of rotation for each device) placed on 16 specimens (two types of inclinometers location).