Filters
total: 7295
-
Catalog
displaying 1000 best results Help
Search results for: heat%20and%20biogas%20plant%20measurements
-
Multi-objective optimization of the ORC axial turbine for a waste heat recovery system working in two modes: cogeneration and condensation
PublicationDue to the demand of the district heating network and electric power grid ORC turbines can operate in the condensation and cogeneration modes. This approach requires the design of an expander which is characterized by high efficiency in each mode of operation. The paper is devoted to a multi-objective efficiency optimization of a one stage axial ORC turbine working on MM (Hexamethyldisiloxane). An Implicit Filtering algorithm (IF)...
-
Investigation on polypropylene friction stir joint: effects of tool tilt angle on heat flux, material flow and defect formation
PublicationTool tilt angle (TTA) is a critical factor that can control material flow in polymeric materials' friction stir joining (FSJ). This study selected a TTA range between 0° to 4° for FSJ of polypropylene (PP) polymer sheet. A modified computational fluid dynamic (CFD) technique was implemented to gain a deep understanding of the effects of TTA during FSJ of PP. The PP joint's internal flow, defect formation, heat generation, and tensile...
-
The Influence of Loop Heat Pipe Evaporator Porous Structure Parameters and Charge on Its Effectiveness for Ethanol and Water as Working Fluids
PublicationAbstract: This paper presents the results of experiments carried out on a specially designed experimental rig designed for the study of capillary pressure generated in the Loop Heat Pipe (LHP) evaporator. The commercially available porous structure made of sintered stainless steel constitutes the wick. Three different geometries of the porous wicks were tested, featuring the pore radius of 1, 3 and 7 um. Ethanol and water as two...
-
Comparison of traditional district heating with low temperature district heating systems featuring organic Rankine cycle and heat pump
PublicationPaper presents a comparison between a traditional district heating system with conventional boilers as a source of heat and electricity purchases from power utilities and a low temperature DH system incorporating the CHP with organic Rankine Cycle providing electricity and local heat pump raising the temperature of the DH fluid to the required temperature in the dwelling, meaning that both heat and electricity are produced within...
-
Antibiotics Act with vB_AbaP_AGC01 Phage against Acinetobacter baumannii in Human Heat-Inactivated Plasma Blood and Galleria mellonella Models
Publication -
Geldanamycin-Induced Osteosarcoma Cell Death Is Associated with Hyperacetylation and Loss of Mitochondrial Pool of Heat Shock Protein 60 (Hsp60)
Publication -
Specificity of automatic control of micro-turbines (steam or gas -driven and expanders) in dispersed generation system of heat and electric power
PublicationThis paper presents specific problems of automatic control of steam micro-turbines and expanders intended for the dispersed, combined generating of heat and electric power. The investigations concern ensurance of certainty of energy supply and its required quality.
-
Ekonomična efektivnist` teplovoï pompi v sistemi opalennâ = Economical efficiency of heat pump system in heating system
PublicationW artykule opisano wynik porównawczych obliczeń kosztów ogrzewania budynku jednorodzinnego. Porównano koszty konwencjonalnego ogrzewania z kotłem olejowym jako źródłem ciepła z kosztami ogrzewania układem hybrydowym, w którym współpracują ze sobą dwa żródła ciepła: konwencjonalny kocioł olejowy i sprężarkowa pompa ciepła. Wykonano studium parametryczne kosztów ogrzewania z wykorzystaniem metody kosztów narastających.
-
Heat transfer and pressure drop during flow boiling of pure efrigerants and refrigerant/oil mixtures in tube with porous coating
PublicationW pracy przedstawiono wpływ powłoki porowatej na średni współczynnik przejmowania ciepła oraz opory przepływu podczas wrzenia wybranych czynników chłodniczych wewnątrz poziomych rurek. Badania przeprowadzono dla techniczne czystych czynników chłodniczychR22, R134a i R407C oraz ich mieszanin z olejem poliestrowym 1% i 5% wrzących w rurkach wykonanych ze stali nierdzewnej, o wewnętrznej powierzchni gładkiej oraz z metaliczną powłoką...
-
Pool boiling heat transfer of water-Al2O3 and water-Cu nanofluids on horizontal stainless steel smooth and rough tubes
PublicationPrzedstawiono wyniki badań eksperymentalnych przejmowania ciepła przy wrzeniu nanocieczy woda-Al2O3 i woda-Cu na poziomych rurkach ze stali nierdzewnej. Ustalono, że niezależnie od badanej koncentracji nanocząstek (0.01%, 0.1% oraz 1%) współczynnik przejmowania ciepła dla nanocieczy był wyższy niż dla wody i rósł ze wzrostem koncentracji. Ponadto współczynnik przejmowania ciepła dla nanocieczy wzrastał ze wzrostem ciśnienia.
-
OCCUPATIONAL RISK ASSESSMENT USING THE RISK SCORE METHOD DURING GEODETIC MEASUREMENTS
Publication -
Quantitative Ultrasound Bone Measurements in Pre-Pubertal Children with Type 1 Diabetes
Publication -
Geospatial Coverage and Signal Quality Measurements of Terrestrial DAB+ Network in Northern Poland
PublicationModern signal coverage maps are prepared based on industry-standard radio propagation models, which take into account a number of parameters, including: type of antenna, distance from the transmitter, type of terrain, etc. However, such simulations are prone to location-specific inaccuracies, and should be verified with in-situ measurements. This paper presents results of a field test of a terrestrial DAB+ (Digital Audio Broadcasting...
-
Verification of GNSS Measurements of the Railway Track Using Standard Techniques for Determining Coordinates
PublicationThe problem of the reproduction of the railway geometric layout in the global spatial system is currently solved in the form of measurements that use geodetic railway networks and also, in recent years, efficient methods of mobile positioning (mainly satellite and inert). The team of authors from the Gdańsk University of Technology and the Maritime University in Gdynia as part of the research project InnoSatTrack is looking for...
-
Space vector modulation in multilevel inverters of the servo drives of the trajectory measurements telescopes
PublicationUsing the MatLab/Simulink mathematical model of a three-phase three-level voltage inverter, the influence of the space-vector modulation (SVM) algorithm on the pulsations of the current (torque) of an AC motor in the range of low rotation speeds is considered. It is shown that the SVM of the second kind does not provide a pulsations level comparable to the pulsations of a sinusoidal pulse-width modulation (SPWM), both in the static...
-
Assessment of Adjustment of GNSS Railway Measurements with Parameter-Binding Conditions in a Stationary Scenario
PublicationThe study aims to assess the applicability of the ordinary least squares method, robust estimation, and conditions-binded adjustment in processing the six synchronous coordinate pairs of global navigation satellite system (GNSS) receivers. The research is part of the research project InnoSatTrack, focused on the enhancement of the determination of geometrical parameters of railway tracks using GNSS, inertial, and other sensors....
-
Testing of the longest span soil-steel bridge in Europe – new quality in measurements
PublicationThe article describes interdisciplinary and comprehensive diagnostic tests of final bridge inspection and acceptance proposed for a soil – steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure response was collected. The load test design was based on the nonlinear numerical simulations performed by...
-
Measurements of Two-phase Flows in Pipelines Using Radioisotopes and Statistical Signal Processing
PublicationThis paper presents an application of radiotracers and gamma absorption method in two-phase flow measurements in pipelines. Two different methods were implemented to analysis of acquired signals. Investigated methods are based on the cross-correlation function and the phase of the cross-spectral density distribution. The examples presented in the article illustrate the application of the radioisotopes to evaluation of liquid-gas...
-
Tyre/road noise measurements on ISO tracks using the modified CPX method
PublicationTyre rolling noise test method specified in the UNECE Regulation 117 is directly used in the Tyre Labelling Directive. Noise level specified on EU Tyre Label of each new tyre available on the European market was determined based on vehicle coast-by noise measurements performed on the standard reference road surface proscribed in the ISO 10844:2014. Available data from investigations by the vehicle and tyre industry and results...
-
Tyre/road noise measurements on ISO tracks according to the UNECE Regulation 117
PublicationWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on 3 ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance, and this directive is based on the measurement procedures defined in the UN ECE Reg.117. The same test car, test tyres and measurement equipment as well as personnel were used...
-
Verification of GNSS measurements of the railway track using standard techniques for determining coordinates
Publication -
Digital filtering of railway track coordinates in mobile multi-receiver GNSS measurements
Publication -
Evaluation of fouling potential of nanofiltration membranes based on the dynamic contact angle measurements
Publication -
Assessment of Adjustment of GNSS Railway Measurements with Parameter-Binding Conditions in a Stationary Scenario
Publication -
Total cross-section measurements for electron collision with α-tetrahydrofurfuryl alcohol (C5H10O2)
PublicationPrzedstawiono całkowite przekroje czynne (TCS) na rozpraszanie elektronów na drobinach α-tetrahydrofurfurylu, zmierzone w zakresie energii zderzenia 1-370 eV oraz policzone powyżej 50 eV. Przedyskutowano otrzymaną zależność TCS od energii. Wyniki porównano z dostępnymi teoretycznymi i eksperymentalnymi przekrojami czynnymi.
-
Application of pH measurements for the following the course of biological treatment of wastewater and its control
PublicationZaprezentowano wyniki badań przeprowadzonych w skali laboratoryjnej w reaktorze imitującym działanie reaktora SBR. Oczyszczaniu poddano ścieki syntetyczne z dodatkiem glukozy. W trakcie oczyszczania ścieków monitorowano zmiany pH, redox, przewodności oraz stężenia azotu amonowego, azotanów i fosforanów. Stwierdzono korelację między pH i zmianami stężenia fosoranów oraz brak podobnej zależności dla związków azotowych.
-
Road noise mapping in the city area: measurements compared to model-based estimations
PublicationThe paper presents an approach to the verification of noise prediction models in selected localization in the city of Gdansk. The experiments described include a comparison between environmentalmeasurement results performed in the terrain and the noise level prediction results. The NMPB-96 (Nouvelle Méthode de Prévision du Bruit) and Harmonoise models outcomes provide the subject ofthe analysis. The proposed solution of continuous...
-
Measurements of absolute elastic and vibrational cross sections for electron scattering from tetrahydrofuran
PublicationPrzedstawiono wstępne wyniki pomiaru absolutnych przekrojów czynnych na zderzenie elektronów z drobinami tetrahydrofuranu przy energii 10eV.
-
Measurements of inelastic electron scattering from molecular oxygen at high scattering angles
PublicationBadano procesy wzbudzenia oscylacyjnego poziomów v = 1-9 stanu podstawowego X3 sigma g oraz v=0 stanu wzbudzonego a1 delta g cząsteczki tlenu dla energii 10eV w przedziale kąta rozproszenia od 90 do 180 st. Dla pomiaru v=1 stanu X3 sigma g wyznaczono różniczkowy przekrój czynny na wzbudzenie. W pomiarach wykorzystano podwójny hemisferyczny spektrometr elektrostatyczny wykorzystujący nowozaprojektowane źródło lokalnego pola magnetycznego.
-
Experimental measurements of artificial hip joint surfaces and applications for the preassure and capacity distributions
PublicationZe względu na wzrastającą potrzebę wszczepiania człowiekowi endoprotez stawu biodrowego, niniejsza praca przedstawia badania geometrycznej struktury ich powierzchni, które mają znaczący wpływ na proces smarowania, eksploatacji oraz funkcjonowanie narządów ruchu.
-
PtCo cathode electrocatalyst behaviour viewed by in-situ XAFS fuel cell measurements
PublicationW pracy zostały przedstawione wstępne wyniki analizy XAS (X-ray absorption spectroscopy), TEM (transmission electron microscopy) i XRD (X-ray diffraction) nanostruktur PtCo 1:1 (20% fazy metalicznej osadzonej na węglu, Vulcan XC-72) używanych jako elektrokatalizatory w polimerowych ogniwach paliwowych (PEM FC). Pomiary realizowane były również w warunkach pracy ogniwa paliwowego za pomocą specjalnie zoptymalizowanej do pomiarów...
-
Comparison of commercial thermoluminescent readers regarding high-dose high-temperature measurements
Publication -
Radioisotope measurements of the liquid-gas flow in the horizontal pipeline using phase method
PublicationThe paper presents application of the gamma-absorption method to a two-phase liquid-gas flow investigation in a horizontal pipeline. The water-air mixture was examined by a set of two Am-241 radioactive sources and two NaI(Tl) scintillation probes. For analysis of the electrical signals obtained from detectors the cross-spectral density function (CSDF) was applied. Results of the gas phase average velocity measurements for CSDF...
-
An in-depth look at the tire rubber hardness influence on tire/road noise measurements
PublicationWhen assessing the acoustic quality of a road pavement with the close-proximity (CPX) or the on-board sound intensity (OBSI) method, the rubber hardness of the reference tire substantially affects the measurement. Practical experience shows that measurement tires can get significantly harder within a single measurement season. This is why one would like to normalize measurements to a reference rubber hardness. The recently published...
-
Measurements of passive components using of an IEEE 1149.4 mixed-signal test bus
PublicationW pracy przedstawiono wyniki badań nad wykorzystaniem magistrali testującej mieszanej sygnałowo IEEE 1149.4 do pomiarów elementów pasywnych zamontowanych na pakietach elektronicznych. Do badań użyto wyposażonych w magistralę układów scalonych typu STA400. Zaprezentowano metody pomiaru rezystancji pojedynczych elementów z wykorzystaniem źródła prądowego oraz źródła VH znajdującego się w analogowych modułach ABM układu STA400. Pokazano...
-
Designing of Track Axis Alignment with the Use of Satellite Measurements and Particle Swarm Optimization
PublicationDesigning of the track’s alignment is a key issue from the point of view of maintaining of proper geometries. The paper presents a design method for sections of railway line located in the horizontal arch. The method is adapted to the technique of mobile satellite measurements. The general principles of this measurement method have been described in the article. A project's solution has been presented using mathematical notation...
-
Composite Sandwich Footbridge – Numerical ESL FEM Calculations vs. In Situ Measurements
PublicationSelected results of the static analysis of composite sandwich footbridge with the corresponding in situ measured values are compared in the paper. The analysed bridge is a research object, which was built in 2015 and is currently located at the Gdańsk University of Technology campus. Since it is a novel structure, a proper definition of the bridge numerical model, allowing its safe design, is very important. Therefore, instead...
-
The process of identification of the track's geometrical layout and the alignment project based on the of satellite measurements
PublicationIn the paper a methodology of restoring of railway track’s geometrical shape in a horizontal plane on the base of conducted mobile satellite surveying was presented. The authors proposed a calculating algorithm for designing the track sections placed in horizontal arcs. In the algorithm an analytical methodology with mathematical formulas is applied. The procedure has an universal character, i.e. provides the possibility of varying...
-
Computer-Aided Design of Railroad Horizontal Arc Areas in Adapting to Satellite Measurements
PublicationThis paper presents a method of designing railway sections located in horizontal arcs. The adopted procedure is universal, i.e., it creates the possibility of varying both the type and the length of the assumed transition curves. This means that the applied analytical formulas apply to the boundary conditions of the transition curves and all of the simplifications widely existing in common algorithms have been eliminated. The presented...
-
Galvanostatic impedance measurements for the efficient adsorption isotherm construction in corrosion inhibitor studies
PublicationWe present an approach towards an accurate and time-efficient adsorption isotherm determination to evaluate the corrosion inhibitor interaction in electrolytic environments. The approach is based on dynamic impedance spectroscopy measurements in galvanostatic mode (g-DEIS). The studied corrosion inhibitor is continuously injected between the secondary cell and the corrosion cell. The efficiency corresponding to instantaneous inhibitor...
-
Radio Channel Measurements in 868 MHz Off-Body Communications in a Ferry Environment
PublicationIn this paper, a characterization of the 868 MHz off-body radio channel in BANs is presented. Measurements were carried out in a ferry environment using a specific set-up. A method for path loss using radio distance measurements (RDMs) was developed. It allows to automate the measurements process and make it independent from the variable speed of a moving person. Based on the observed path loss as a function of distance, the obtained...
-
Total electron-scattering cross section measurements for tetrahydropyran, (CH2)5O, molecules
PublicationZmierzono całkowity przekrój czynny (TCS) na rozproszenie elektronów na drobinach tetrahydropyranu. Pomiary przeprowadzono metodą transmisyjną w zakresie energii zderzenia 1 - 400 eV. Otrzymana zależność energetyczna TCS wskazuje na obecność procesów rezonansowych w zakresie 3 - 15 eV. Wyniki porównano z całkowitymi przekrojami czynnymi dla drobin tetrahydrofuranu i alkoholu alfa-tetrahydrofurfurylowego.
-
Developing electrochemical measurements in order to assess anti-corrosive coatings more effectively
PublicationCelem pracy było sprawdzenie powtarzalności wyników uzyskanych metodą pomiaru szumu (Electrochemical Noise method - ENM) elektrochemicznego wykonanych na powłokach organicznych w konfiguracji bez połączenia z podłożem metalowym (NOCS - No Connection to the Substrate). NOCS polega na wykonaniu pomiarów na trzech teoretycznie takich samych obszarach badanego układu. W takim układzie nie jest wymagane połączenie elektryczne z metalowym...
-
Raman Spectra Measurements for Chemical Identifications - Aspect of Uncertainty Sources and Reduction of Their Effects
PublicationRaman spectrometers enable fast and non-contact identification of examined chemicals. These devices measure Raman spectra and compare with the spectra database to identify unknown and often illicit chemicals (e.g. drugs, explosives) usually without any sample preparation. Raman spectra measurements are a challenge due to noise and interferences present outside the laboratories (field applications). The design of a portable Raman...
-
Adjusted subpixel method enables optimisation of bronchial measurements in high-resolution CT
PublicationArtykuł przedstawia metodę korekcji pomiaru rozmiaru oskrzeli w techice HRCT. W celu walidacji metody zastosowano fantom. W efekcie opracowano metodę nieliniowej predykcji rzeczywistych rozmiarów ścianek małych oskrzeli w obrazach HRCT.
-
Measurements of ASON/GMPLS connection control layer performance according to the ETSI methodology
PublicationMeasurements of performance have always been crucial for evaluation of telecommunication systems, especially for implementation of network control elements responsible for connection handling which regards to bandwidth reservation, modification and release. That problem also arises in Automatically Switched Optical Network/Generalized Multiprotocol Label Switching (ASON/GMLPS) architecture, which is considered as one of the components...
-
Particle Image Velocimetry Measurements of Airflow in Electrohydrodynamic Device for Dust Particle Collection
PublicationIn this paper the electrohydrodynamic (EHD)device for gas pumping and cleaning is presented. To induce an airflow in this EHD device corona discharge was used. The discharge was generated between the one-sided spike electrodes and the plate electrodes. An asymmetric electric field and generated discharge result in unidirectional gas flow through the EHD device. The current-voltage characteristics were measured and the corona discharge...
-
Efficient three-dimensional fluorescence measurements for characterization of binding properties in some plants
PublicationThe main aim of this research was to characterize some plants and to determine their similarities and differences, using spectroscopic methods. The interactions of soluble polyphenols of different plants with human serum albumin (HSA) were investigated by 3D-fluorescence. The obtained fluorescence results allow to classify the investigated plants according to their binding properties. The HSA-binding capacities of these plants...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublicationTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
Certified Reference Material - as a necessary tool for the quality control and quality assurance of measurements
PublicationReference materials are necessary to control and ensure the quality of the measurements. The demand for analytical information on the composition of different material objects makes it necessary to produce an even wider range of materials.