Filters
total: 1141
filtered: 937
-
Catalog
Chosen catalog filters
Search results for: PBE
-
Fracture surface topography measurements analysis of low-alloyed corrosion resistant steel after bending-torsion fatigue tests
PublicationIn this paper, an assessment of a topography measurement method for fracture surfaces of 10HNAP steel after bending-torsion fatigue tests was performed. Surface roughness was measured by using a non-contact Focus Variation Microscopy (FVM) technique in which the non-measured points (NMPs) and outliers (spikes) were removed by the application of general methods. The results revealed, that the optical measurement method introduced...
-
Infographics in Educational Settings: A Literature Review
PublicationInfographics are visual representations of data that utilize various graphic elements, including pie charts, bar graphs, line graphs, and histograms. Educators and designers can maximize the potential of infographics as powerful educational tools by carefully addressing challenges and capitalizing on emerging technologies. However, current education systems showcase the need for development guidelines and the best practices targeted...
-
Powojenny rozdział w historii architektury i zagospodarowania portu gdyńskiego
PublicationThe port of Gdynia, considered one of the largest civil construction projects of the 20th century in Europe, was built at an express pace for only a dozen or so years from the mid-1920s to the end of the 1930s. Unusual solutions from the construction period in the port engineering category, as well as outstanding architectural works The industrial area quickly became architectural symbols of economic growth and the general rebirth...
-
Towards Carbon Neutral Settlements. The Importance of Early-Stage Urban and Energetic Optimizations
PublicationThe aim of the research was to verify the essence of interdisciplinary energy optimizations in earlystage urban design process. A further aim was to the find most optimal design variant and scenario in terms of urban energy efficiency for the future development in Nowy Port, located in Gdansk, Poland - a place requiring complex revitalization. The research combined qualitative and quantitative approaches; an urban design layer...
-
Hybridized Space-Vector Pulsewidth Modulation for Multiphase Two-Level Voltage Source Inverter
PublicationIn space vector pulsewidth modulation (SVPWM) algorithms for multiphase two-level voltage source inverters (VSI), the components of active vectors in all orthogonal spaces have to be calculated within the processor and stored in its memory. These necessitate intensive computational efforts of the processor and large memory space. This article presents a hybridized SVPWM for multiphase two-level VSI. In this algorithm, elements...
-
Earthquake-induced pounding between asymmetric steel buildings
PublicationEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phe-nomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Seeding enhancement for microcrystaline diamond layers growth on non-diamond substrates
PublicationThe present paper gives an overview on the possible methods of seeding substrates for diamond layers growth. Diamond in reason of his properties is very desirable material in microelectronic, biomedical and waste treatment sensors. Microcrystalline diamond for these applications must be grown on silicon substrate in microwave plasma assisted chemical vapor deposition (MPACVD). To grow diamond on non-diamond surface pre-growth...
-
Evolutionary Sets of Safe Ship Trajectories Within Traffic Separation Schemes
PublicationThe paper presents the continuation of the author's research on Evolutionary Sets of Safe Ship Trajectories (ESoSST) methodology. In an earlier paper (Szlapczynski, 2011) the author described the foundations of this methodology, which used Evolutionary Algorithms (EA) to search for an optimal set of safe trajectories for all the ships involved in an encounter. The methodology was originally designed for open waters or restricted...
-
Bio polyetherurethane composites with high content of natural ingredients: hydroxylated soybean oil based polyol, bio glycol and microcrystalline cellulose
PublicationIn our study, we focused on obtaining bio-polyurethane composites using bio-components such as bio glycol, modified natural oil-based polyol, and microcrystalline cellulose (MCC). The pre-polymer method was used to prepare the bio polyurethane matrix. Prepolymer was synthesized using 4,4’-diphenylmethane diisocyanate (MDI) and a polyol mixture containing 50 wt.% of commercial polyether and 50 wt.% of hydroxylated soybean oil (H3)....
-
Nanoporous TiO2 electrode grown by laser ablation of titanium in air at atmospheric pressure and room temperature
PublicationRecently, fabrication of the nanoporous TiO2 photoelectrode on metal foils by means of sputtering of the Ti film on preheatedmetal substrate followed by the TiO2 deposition (doctor blade technique) and sintering represents the frequently applied technique. This is despite the relatively complicated procedure and number of parameters to be controlled in order to fabricate films of required properties. In this work an approach is...
-
Toward Fast Calculation of Communication Paths for Resilient Routing
PublicationUtilization of alternate communication paths is a common technique to provide protection of transmission against failures of network nodes/links. However, a noticeable delay is encountered when calculating the relevant sets of disjoint paths using the available algorithms (e.g., using Bhandari’s approach). This, in turn, may have a serious impact on the ability of a network to serve dynamic demands...
-
Application of soil nailing technique for protection and preservation historical buildings
PublicationSoil nailing is one of the recent in situ techniques used for soil improvement and in stabilizing slopes. The process of soil nailing consists of reinforcing the natural ground with relatively small steel bars or metal rods, grouted in the pre-drilled holes. This method has a wide range of applications for stabilizing deep excavations and steep slopes. Soil nailing has recently become a very common method of slope stabilisation...
-
High-Resolution Discharge Forecasting for Snowmelt and Rainfall Mixed Events
PublicationDischarge events induced by mixture of snowmelt and rainfall are strongly nonlinear due to consequences of rain-on-snow phenomena and snowmelt dependence on energy balance. However, they received relatively little attention, especially in high-resolution discharge forecasting. In this study, we use Random Forests models for 24 h discharge forecasting in 1 h resolution in a 105.9 km 2 urbanized catchment in NE Poland: Biala River....
-
Brain-computer interaction based on EEG signal and gaze-tracking information = Analiza interackji mózg-komputer wykorzystująca sygnał EEg i informacje z systemu śledzenia punktu fiksacji wzroku
PublicationThe article presents an attempt to integrate EEG signal analysis with information about human visual activities, i.e. gaze fixation point. The results from gaze-tracking-based measurement were combined with the standard EEG analysis. A search for correlation between the brain activity and the region of the screen observed by the user was performed. The preliminary stage of the study consists in electrooculography (EOG) signal processing....
-
Investigation on Filaments for 3D Printing of Nasal Septum Cartilage Implant
PublicationSeptoplasty is a widely used method in treating deviated septum. Although it is successfully implemented, there are problems with excessive bleeding, septal perforation, or infections. The use of anatomically shaped implants could help overcome these problems. This paper focuses on assessing the possibility of the usage of a nasal septum cartilage implant 3D printed from various market-available filaments. Five different types...
-
Ekspertyza z pomiarów drgań linii wałów na jednostce ORP "ORKAN"
PublicationEkspertyza diagnostyczna dotycząca stanu technicznego trzech linii transmisji mocy (linii wałów) opracowana na podstawie przeprowadzonych pomiarów drgań w 14 punktach pomiarowych, przy jednoczesnej pracy silników napędowych L, ŚR i PB (wspólnej pracy wszystkich linii wałów), w III zakresach ustalonego obciążenia. Pomiary prędkości i przyspieszeń drgań generowanych przez węzły konstrukcyjne okrętowego układu napędowego wykonano...
-
Conductivity and superconductivity in granular materials
PublicationMetale i nadprzewodniki granulaste są bardzo ciekawymi materiałami dzięki jednoczesnej obecności oddziaływań kulombowskich, tunelowania elektronów i par Coopera oraz różnych zjawisk związanych z nieuporządkowaniem. W pracy przedstawiono i porównano niektóre właściwości granulastych nisko- i wysokotemperaturowych nadprzewodników. Granulasty nadprzewodnik wysokotemperaturowy otrzymano metodą krystalizacji w fazie stałej szkła (Bi,Pb)-Sr-Ca-Cu-O....
-
Przykłady zastosowań
PublicationW rozdziale przedstawiono przykładowy sposób analizy funkcji systemów sterowania i zabezpieczeń w odniesieniu do turbozespołu o strukturze typu: kocioł-turbina-generator. Ryzyko związane z eksploatacją turbozespołu zależy od różnych czynników i rozwiązań technicznych, organizacyjnych oraz od zastosowanych podsystemów sterowania, zabezpieczeń oraz systemów E/E/PE związanych z bezpieczeństwem. Jednym z elementów takiego podsystemu...
-
Modelowanie bezpieczeństwa maszyn i instalacji krytycznych
PublicationW rozdziale zostały omówione metody modelowania bezpieczeństwa instalacji krytycznych. W złożonym obiekcie podwyższonego ryzyka wyróżniono warstwy procesu technologicznego, systemów monitorowania i sterowania, alarmów krytycznych i interwencji operatorów, warstwy systemów automatyki zabezpieczeniowej SIS, zabezpieczeń inżynieryjnych, oraz warstwy przeciwdziałań wewnętrznych i zewnętrznych. Zwrócono uwagę na rolę jaką pełnią systemy...
-
Superconducting transition in granular Bi-Sr-Ca-Cu-O superconductors
PublicationW układzie(Bi,Pb)-Sr-Ca-Cu-O poprzez krystalizację w fazie stałej można wytworzyć materiały o bardzo różnych właściwościach elektrycznych i nadprzewodzących. W zależności od warunków krystalizacji, można wytworzyć nadprzewodnik o temperaturze krytycznej między 8 a 105 st. K lub materiał nie przechodzący do stanu nadprzewodzącego. Przejście do stanu nadprzewodzacego w materiałach granulastych ma charakter dwustopniowy. Zbadano wpływ...
-
Effect of bitumen characteristics obtained according to EN and Superpave specifications on asphalt mixture performance in low-temperature laboratory tests
PublicationThe paper aims to identify those characteristics of bitumen which have the greatest impact on asphalt mixture low-temperature performance. It was observed that stiffness and m-value of bitumen from BBR test were moderately related to stiffness and m-value of asphalt mixture obtained from 3 PB test. Simultaneously those rheological properties significantly impact on cryogenic stresses induced during TSRST test. The multiple regression...
-
Ekspertyza z pomiarów drgań linii wałów na jednostce TRB631
PublicationEkspertyza diagnostyczna dotycząca stanu technicznego dwóch linii transmisji mocy (linii wałów) opracowana na podstawie przeprowadzonych pomiarów drgań w 26 punktach pomiarowych, przy jednoczesnej pracy silników napędowych L i PB (wspólnej pracy linii wałów obu burt), w II zakresach ustalonego obciążenia „pół-naprzód” i „cała-naprzód”. Pomiary prędkości i przyspieszeń drgań generowanych przez węzły konstrukcyjne okrętowego układu...
-
RAPORT - EKSPERTYZA Z POMIARÓW DRGAŃ LINII WAŁÓW NA JEDNOSTCE ORP „RESKO”
PublicationEkspertyza diagnostyczna dotycząca stanu technicznego dwóch linii transmisji mocy (linii wałów) opracowana na podstawie przeprowadzonych pomiarów drgań w 26 punktach pomiarowych, przy jednoczesnej pracy silników napędowych L i PB (wspólnej pracy linii wałów obu burt), w II zakresach ustalonego obciążenia „pół-naprzód” i „cała-naprzód”. Pomiary prędkości i przyspieszeń drgań generowanych przez węzły konstrukcyjne okrętowego układu...
-
METODA ANALIZY NIEZAWODNOŚCI CZŁOWIEKA SPAR-H W APLIKACJI ProSIL-EAL
PublicationW referacie przedstawiono zagadnienie wyznaczania prawdopodobieństwa błędu człowieka HEP za pomocą metody SPAR-H w oprogramowaniu ProSIL-EAL. Oprogramowanie wspomaga proces zarządzania bezpieczeństwem funkcjonalnym w cyklu życia systemów technicznych. Prawdopodobieństwo błędu człowieka jest zagadnieniem związanym z etapem weryfikacji określonych poziomów nienaruszalności bezpieczeństwa SIL dla funkcji bezpieczeństwa. ProSIL-EAL...
-
Funcional safety concept for hazardous systems and new challenges
PublicationPrzedstawia się wybrane zagadnienia bezpieczeństwa funkcjonalnego według norm międzynarodowych IEC 61508 i IEC 61511. Opisuje się proces wyznaczanie poziomu nienaruszalności bezpieczeństwa (SIL) systemów elektrycznych, elektronicznych i programowalnych elektronicznych (E/E/PE). Podkreśla się znaczenie modelowania probabilistycznego tych systemów i weryfikowania SIL. Omawia się nowe aspekty analizy bezpieczeństwa funkcjonalnego...
-
Algorytmy przetwarzania widm Ramana w procesie detekcji substancji chemicznych
PublicationRozprawa przedstawia szczegółowo algorytmy, jakie są stosowane podczas przetwarzania widm Ramana, rejestrowanych przenośnym spektrometrem o skończonej rozdzielczości. Pracę podzielono na osiem rozdziałów. W pierwszym określono cel i tezy pracy. Rozdział drugi opisuje podstawowe pojęcia dotyczące zjawiska Ramana oraz zasady budowy urządzeń do pomiarów widm Ramana. W rozdziale trzecim scharakteryzowano błędy występujące podczas pomiarów...
-
Glass-ceramic sealants and steel interconnects: accelerated interfacial stability and reactivity tests at high temperature
PublicationHigh-temperature reactions between glass-ceramic sealants and Fe-Cr alloy interconnects may lead to the formation of undesirable phases, and consequently degradation of solid oxide fuel/electrolyser devices. In this work, three different glass-ceramic sealants (Na-containing, Ba-containing, Sr-containing compositions) and Fe22Cr stainless steel powders (raw and pre-oxidised) are considered in order to test their chemical reactivity...
-
Light-improved glucose sensing on ordered Au-Ti heterostructure
PublicationNon-enzymatic electrochemical platforms sensitive towards glucose presence have attracted a worldwide attention during last decades. We report on influence of solar light onto response of gold-titanium heterostructures prepared via controllable approach. The material based on Au nanoparticles orderly distributed over the structured titanium foil was obtained by electrochemical anodization followed by chemical etching, magnetron...
-
A Flexible Nafion Coated Enzyme‐free Glucose Sensor Based on Au‐dimpled Ti Structures
PublicationThe detection of glucose at low concentrations using electrochemical sensors is of great importance due to the possibility of using different human body fluids than blood, such as e.g. urine, saliva, sweat or tears. The interest behind those biofluids is related to their utility in non-invasive sugar determination. In this work, we present flexible, fully biocompatible electrode material based on Au nanoparticles immobilized onto...
-
Accelerated design optimization of miniaturized microwave passives by design reusing and Kriging interpolation surrogates
PublicationElectromagnetic (EM) analysis has become ubiquitous in the design of microwave components and systems. One of the reasons is the increasing topological complexity of the circuits. Their reliable evaluation—at least at the design closure stage—can no longer be carried out using analytical or equivalent network representations. This is especially pertinent to miniaturized structures, where considerable EM cross-coupling effects occurring...
-
Reliable Surrogate Modeling of Antenna Input Characteristics by Means of Domain Confinement and Principal Components
PublicationA reliable design of contemporary antenna structures necessarily involves full-wave electromagnetic (EM) analysis which is the only tool capable of accounting, for example, for element coupling or the effects of connectors. As EM simulations tend to be CPU-intensive, surrogate modeling allows for relieving the computational overhead of design tasks that require numerous analyses, for example, parametric optimization or uncertainty...
-
A selection of the optimal eluent components for separation of carnivorous plants metabolites by planar chromatography chromatography
PublicationAbstract: The development of the new procedures of the separation components with the complicated chemical structure from natural complex matrix by column chromatography is very difficult and in many cases expensive. Therefore to pre-select the conditions of the separation process the use of thin layer chromatography (TLC) is proffered. The possibility of proceeding the chromatographic process for several mixtures on single plate,...
-
Effects of thermal history on the performance of low-temperature solid oxide fuel cells with Sm0.2Ce0.8O2-δ electrolyte and LiNi0.81Co0.15Al0.04O2 electrodes
PublicationIn this study, low-temperature solid oxide fuel cells with an ∼560 μm thick Sm0.2Ce0.8O2−δ (SDC) electrolyte and ∼890 μm thick LiNi0.81Co0.15Al0.04O2−δ (NCAL) electrodes are constructed and characterized under three experimental conditions. The cell with an NCAL cathode pre-reduced under an H2 atmosphere at 550 °C presents the best electrochemical performance. This is ascribed to facts that the reduction reaction generating Ni–Co...
-
FTIR, Raman spectroscopy and HT-XRD in compatibility study between naproxen and excipients
PublicationDetection of incompatibility between an active pharmaceutical ingredient (API) and excipients, including the selection of the most biopharmaceutical advantageous excipients is extremely important in the pre-formulation process of developing a solid dosage form technology. Therefore, having fast and reliable methods for identifying incompatibility is fundamental in pharmaceutical technology. For this purpose, combined Fourier transform...
-
Ultrasound-Assisted Dispersive Liquid-Liquid Microextraction Using Deep Eutectic Solvents (DESs) for Neutral Red Dye Spectrophotometric Determination
PublicationDeep eutectic solvents (DES), which have low toxicity and are low cost, biodegradable, and easily synthesized, were used for the extraction of neutral red (NR) dye before its spectrophotometric analysis. DES, containing choline chloride as a hydrogen bond acceptor and phenol as a hydrogen bond donor with a molar ratio of 1:2, was used for the extraction of NR dye from aqueous media. The possible interaction of different DESs with...
-
The Multiplatform Environment for Simulation and Features Estimation of Mixed-Signal Devices
PublicationThe use of simulation laboratories is gaining popularity in thedomains of engineering programs. However, the experience in teaching showsthat the simulation itself is not very effective in didactic processes. Teachingprocesses in thefield of specialist subjects, designed for students of technicaluniversities, should be based on direct operations performed by the student onreal devices. At the same time, at the later stages of didactic...
-
Performance-driven yield optimization of high-frequency structures by kriging surrogates
PublicationUncertainty quantification is an important aspect of engineering design, as manufacturing toler-ances may affect the characteristics of the structure. Therefore, quantification of these effects is in-dispensable for adequate assessment of the design quality. Toward this end, statistical analysis is performed, for reliability reasons, using full-wave electromagnetic (EM) simulations. Still, the computational expenditures associated...
-
Study of microstress state of P91 steel using complementary mechanical Barkhausen, magnetoacoustic emission, and X-ray diffraction techniques
PublicationThe paper deals with assessment of microstress state of martensite P91 steel using three complementary techniques: mechanical Barkhausen emission, magnetoacoustic emission (MAE), and X-ray diffraction (XRD) profile analysis. Magnetic coercivity Hc and microstructure were investigated with inductive magnetometry and magnetic force microscopy (MFM), respectively. Internal stress level of P91 steel was modified by heat treatment....
-
Impact of overloaded vehicles on load equivalency factors and service period of flexible pavements
PublicationOverloaded vehicles occur less frequently in comparison to properly loaded vehicles but due to their greater potential to cause damage they significantly contribute to the distress of pavement structure. As the studies show, the phenomena of vehicles overloading intensifies when the control of traffic is poor and the average percentage of overloaded vehicles on analyzed roads varies from 6% to 23%. The main goal of the ar-ticle...
-
Optical and electrical properties of boron doped diamond thin conductive films deposited on fused silica glass substrates
PublicationThis paper presents boron-doped diamond (BDD) film as a conductive coating for optical and electronic purposes. Seeding and growth processes of thin diamond films on fused silica have been investigated. Growth processes of thin diamond films on fused silica were investigated at various boron doping level and methane admixture. Two step pre-treatment procedure of fused silica substrate was applied to achieve high seeding density....
-
Data-Driven Surrogate-Assisted Optimization of Metamaterial-Based Filtenna Using Deep Learning
PublicationIn this work, a computationally efficient method based on data driven surrogate models is pro-posed for the design optimization procedure of a Frequency Selective Surface (FSS)-based filtering antenna (Filtenna). A Filtenna acts as a as module that simultaneously pre-filters unwanted sig-nals, and enhances the desired signals at the operating frequency. However, due to a typically large number of design variables of FSS unit elements,...
-
Non-linear static stability of bi-layer carbon nanosheets resting on an elastic matrix under various types of in-plane shearing loads in thermo-elasticity using nonlocal continuum
PublicationIn this research, the shear and thermal buckling of bi-layer rectangular orthotropic carbon nanosheets embedded on an elastic matrix using the nonlocal elasticity theory and non-linear strains of Von-Karman was studied. The bi-layer carbon sheets were modeled as a double-layered plate, and van der Waals forces between layers were considered. The governing equations and boundary conditions were obtained using the first order shear...
-
GUIDED WAVES IN SHIP STRUCTURAL HEALTH MONITORING – A FEASIBILITY STUDY
PublicationShips and offshore structures operate in a severe corrosion degradation environment and face difficulty in providing long- lasting corrosion protection. The Classification Societies recommend regular thickness measurements leading to structural component replacements, to ensure structural integrity during service life. The measurements are usually performed using ultrasonic thickness gauges and such an approach requires multiple...
-
Defected Ag/Cu-MOF as a modifier of polyethersulfone membranes for enhancing permeability, antifouling properties and heavy metal and dye pollutant removal
PublicationIn this study, a novel bimetallic metal-organic framework (MOF) i.e. Ag/Cu-MOF was synthesized using a solvothermal method and later incorporated at different concentrations (0.1–2 wt%) using a phase inversion method for modification and antifouling property improvement of polyethersulfone (PES) membranes. The resulting Ag/Cu-MOF characteristics were investigated using different techniques, such as FTIR, XRD, FE-SEM and EDX. The...
-
Rainwater chemistry composition in Bellsund: Sources of elements and deposition discrepancies in the coastal area (SW Spitsbergen, Svalbard)
PublicationDiscrepancies in rainfall chemistry in Bellsund were found to be influenced by the orographic barrier and related to the variability in the inflow of air masses as well as to the distance of sampling sites from the sea and thus the extent of sea spray impact. This study covers measurements of rainfall (P) and air temperature (T), physicochemical parameters (pH, specific electrolytic conductivity (SEC), major ions (Cl , NO3 , SO4...
-
Anthropogenic trace metals in Setiu Wetland: Spatial and seasonal distribution and implications for environmental health
PublicationThe growing urban wastewater volume poses a major global environmental challenge, especially in developing nations where inadequate treatment and discharge impact clean water availability. This study focused on Setiu Wetland, aiming to analyze seasonal and spatial variations of trace metals in particulate form from anthropogenic and pathogenic sources. Surface water samples were collected from multiple stations, measuring physical...
-
Specjacja metali ciężkich w ściekach i wodach odciekowych podczas oczyszczania ścieków w reaktorach systemu MUCT
PublicationCelem prowadzonych badań była analiza występowania i dostępności wybranych metali ciężkich po kolejnych stopniach oczyszczania w wysokoefektywnej oczyszczalni z biologicznym usuwaniem azotu i fosforu. Przeprowadzono analizę rozmieszczenia fazowego wybranych metali pomiędzy fazą rozpuszczoną i zawiesinową dla ścieków oraz wód odciekowych. Zastosowanie ekstrakcji sekwencyjnej pozwoliło na określenie stężeń wybranych metali ciężkich:...
-
Atmospheric heavy metal deposition accumulated in rural forest soils of southern Scandinavia
PublicationPrzeprowadzono obliczenia zakumulowanej ( w okresie 50 lat) atmosferycznej depozycji metali ciężkich na glebach leśnych na obszarach wiejskich. Podstawę do obliczeń stanowiły:- pomiary zawartości metali ciężkich w opadach atmosferycznych (przeprowadzone przez okres 33 lat) na terenie Danii,- europejska baza danych o emisji zanieczyszczeń.Oznaczano zawartość metali ciężkich (Pb, Cd, Cu, Zn, V, Ni, As) w próbkach opadów atmosferycznych...
-
Managing competence and certifying persons responsible for functional safety = Zarządzanie kompetencjami i certyfikacja osób odpowiedzialnych za bezpieczeństwo funkcjonalne
PublicationThis article emphasizes that knowledge and competences of managers, engineers and specialists dealing with safety-related technologies for hazardous industry should be appropriately shaped in the technical education processes and training programmes fulfilling some quality requirements and assessment criteria. It concerns especially persons dealing with the functional safety solutions in the design and operation of the electric,...
-
Ocena stanu technicznego głównego układu napędowego na jednostce "Kapitan Poinc" na podstawie pomiarów drgań
PublicationEkspertyza diagnostyczna dotycząca stanu technicznego lini transmisji mocy (linii wałów) opracowana na podstawie przeprowadzonych pomiarów drgań w 10 punktach pomiarowych, przy jednoczesnej pracy silników napędowych L i PB (wspólnej pracy linii wałów obu burt), w IV zakresach ustalonego obciążenia wyznaczanego skokiem śrub nastawnych tzn.: 20%, 40%,60% i 80%. Pomiary prędkości i przyspieszeń drgań generowanych przez węzły konstrukcyjne...