Filters
total: 5690
filtered: 4045
displaying 1000 best results Help
Search results for: COUPLED VIBRATIONS
-
Numerical study on pounding between two adjacent buildings under earthquake excitation
PublicationSeismic excitation, which results in large horizontal relative displacements, may cause collisions between two adjacent structures due to insufficient separation distance between them. Such collisions, known as earthquake-induced structural pounding, may induce severe damages. In this paper, the case of pounding between two adjacent buildings is studied by the application of single degree-of-freedom structural models. Impact is...
-
Updating Finite Element Model of a Wind Turbine Blade Section Using Experimental Modal Analysis Results
PublicationThis paper presents selected results and aspects of themultidisciplinary and interdisciplinary research oriented for the experimental and numerical study of the structural dynamics of a bend-twist coupled full scale section of awind turbine blade structure.Themain goal of the conducted research is to validate finite elementmodel of themodified wind turbine blade section mounted in the flexible support structure accordingly to the...
-
An approach for the response of buildings subjected to impact load after soft-story failure due to earthquake excitation
Publicationhe soft-story failure is one of the most typical types of damage observed in buildings during earthquakes. The failure of an intermediate soft story of a structure results in large impact loading acting on the lower floors due to the fall of the upper stories. The aim of the present paper is to study the behavior of the structural members exposed to such extreme load conditions occurring under ground motion excitation. Special...
-
Detection of Delamination in Laminate Wind Turbine Blades Using One-Dimensional Wavelet Analysis of Modal Responses
PublicationThis paper demonstrates the effectiveness of a nondestructive diagnostic technique used to determine the location and size of delamination in laminated coatings of wind turbine blades. This is realized based on results of numerical and experimental investigations obtained by the use of the finite element method (FEM) and laser scanning vibrometry (LSV). The proposed method is based on the one-dimensional continuous wavelet transform...
-
Dynamics Conscious Approach to Tribometer Design and Tribo-testing
PublicationIn the paper findings are discussed on the issue of dynamic characteristics of a tribometer as a factor influencing the result of the tribological experiment. An advanced approach to tribo-testing is attempted with integrated dynamic analysis of the tribometer and the sliding pair. The fundamental idea is explored of the tribometer being regarded as any machine in which friction is inflicted with all the resulting consequences...
-
Assessment of Subsoil Subsidence Under the Railway Surface with the Use of Fuzzy Sets
PublicationThe cause of the subsidence of the railway track is the subsidence of the track bed itself and it is often related to the subsidence of the subsoil. Such settlement leads to: uneven longitudinal railways and track twist. These phenomena have a negative impact on the comfort and safety of driving, and in extreme cases lead to a train derailment. It has been shown that the magnitude of these settlements is determined by many parameters...
-
Design and Experiments of a Piezoelectric Motor Using Three Rotating Mode Actuators
PublicationThis paper represents a numerical and experimental investigation of the multicell piezoelectric motor. The proposed design consists of three individual cells that are integrated into the stator, double rotor, and a preload system combined into a symmetrical structure of the motor. Each of the cells is characterized by a traveling wave and rotating mode motor. A finite element numerical analysis is carried out to obtain optimal...
-
Synthesis and characterization of mononuclear Zn(II), Co(II) and Ni(II) complexes containing a sterically demanding silanethiolate ligand derived from tris(2,6-diisopropylphenoxy)silanethiol
PublicationFour heteroleptic complexes of zinc(II), cobalt(II) and nickel(II) containing a monodentate silanethiolate ligand derived from tris(2,6-diisopropylphenoxy)silanethiol (TDST), were prepared and characterized. The geometries of ligands in the complexes are typical: distorted tetrahedral in zinc and cobalt(II) complexes and square planar in nickel(II) compound. Magnetic studies performed for Ni(II) and Co(II) compounds confirm the...
-
Selected Aspects of 3D Printing for Emergency Replacement of Structural Elements
PublicationThe paper presents a synthetic characterization of modern methods of manufacturing or regenerating machine elements. Considered methods are machining and additive methods, in particular 3D printing in the FDM/FFF technique. For the study, the authors made samples of the holder bracket using selected methods. Samples made by machining operations, 3D printing with various filling were tested. The paper contains a technical and economic...
-
Syntheses and structures of the first terminal phosphanylphosphido complex of hafnium [cp2hf(cl){η1-(me3si)p-p(net2)2}] and the firstzirconocene-phosphanylphosphinidene dimer [cp2zr{μ2-p-p(net2)2}2zrcp2]
PublicationReactions of (Et2N)2P-P(SiMe3)Li with [Cp2MCl2] (M= Zr, Hf) in toluene or pentane yield the related terminal phosphanylphosphido complexes [Cp2M(Cl){η1-(Me3Si)P-P(NEt2)2}]. The solid statestructure of [Cp2Hf(Cl){η1-(Me3Si)P-P(NEt2)2}] was established by single crystal X-ray diffraction. The reaction of (Et2N)2P-P(SiMe3)Li with [Cp2ZrCl2] in THF or DME solutions leads to the formationof deep red crystals of the first neutral diamagnetic...
-
Reactions of cobalt(ii) chloride and cobalt(ii) acetate with hemisalen-type ligands: ligand transformation, oxidation of cobalt and complex formation. Preliminary study on the cytotoxicity of Co(ii) and Co(iii) hemisalen complexes
PublicationSeveral molecular cobalt(II) complexes, one Co(II) coordination polymer, and one ionic cobalt(III) complex with imine hemisalen ligands were synthesized. The hemisalen ligands were synthesized from o-vanillin (oVP) and diverse aminopyridines (compounds HL1–HL4) or aminophenol (compound HL5). It was observed that cobalt(II) chloride in dry acetonitrile catalyzes a transformation of HL1 and HL3 instead of complex formation. The conversion...
-
Influence of Additional Loads on Chosen Gait Parameters and Muscles Activity
PublicationThis paper is devoted to human motion analysis and comparison of chosen kinematics parameters during normal gait with and without additional load in a form of backpack. A stability in both cases were compared in both frontal and sagittal planes, by applying a video tracking system. Experimental tests performed on treadmill, passive markers, placed on volunteers bare skin were used. Additionally, an infra-red camera was employed...
-
The modelling method of discrete-continuous systems
PublicationThe paper introduces a method of discrete-continuous systems modelling. In the proposed method a three-dimensional system is divided into finite elements in only two directions, with the third direction remaining continuous. The thus obtained discrete-continuous model is described by a set of partial differential equations. General difference equations of discrete system are obtained using the rigid finite element method. The limit...
-
Hybrid Reduced Model of Continuous System
PublicationThe paper introduces an alternative method of modelling and modal reduction of continuous systems. Presented method is a hybrid one. It combines the advantages of modal decomposition method and the rigid finite element method. In the proposed method continuous structure is divided into one-dimensional continuous elements. For each 1D element modal decomposition and reduction is applied. Interactions between substructures are...
-
Modelling and Identification of Tower Type Historic Buildings
PublicationW pracy omawia się problemy modelowania i identyfikacji zabytkowych murowanych budowli wieżowych na przykładzie wieży Twierdzy Wisłoujście. Przedstawiono analizę modalną na podstawie dwukierunkowych pomiarów przyspieszeń na 9 poziomach wieży. Wyniki analizy posłużyły do identyfikacji modelu matematycznego budowli w postaci sztywnego bloku na podłożu sprężystym. Wykorzystano hierarchiczną procedurę opartą na analizie wrażliwości.
-
Dynamics of mechanical model of implant-tissue system in ventral hernia repair
PublicationThe paper deals with a finite element modelling of implants in the problem of ventral hernia repair. The synthetic mesh implanted in the abdomen during surgery is here modelled as a membrane structure. Thesystem undergoes the internal abdominal pressure that occurs during the postoperative cough, the load identified in the literature as the main cause of the connection failure and hernia recurrence. The model can be used to estimate...
-
A tool for designing water tanks for measuring hydroacoustic transducers
PublicationSpecial water tanks are commonly used to measure the parameters of underwater acoustic systems. They must meet specific requirements, the fulfilment of which ensures very small but acceptable measurement errors. These requirements define the size of the tank and its shape as well as the strong attenuation of reflected waves. At the design stage, it is necessary to determine the impact of the tank structure on the measurement errors...
-
Synchronization system for underwater acoustic communications using in shallow waters
PublicationA reliable synchronization system of the transmitted data frame has a significant impact on the efficiency of the underwater communication system. This applies in particular to communication systems dedicated to work in shallow waters, where the phenomenon of multipath permanently occurs. To overcome these difficulties, the concept of a synchronization system consisting of two broadband signals of opposite monotonicity was presented....
-
Noise effect on parameters of quiet sonar with code modulation
PublicationEarlier publications of the paper authors have shown that the use of code keying mixed with the CW FM sound signal allows the significant reduction in the distance measurement error, compared to classic silent CW FM sonar. In addition to the code modulation parameters, the magnitude of this error is influenced by the received input acoustic noise. The article shows the dependence of the input signal-to-noise ratio and the sound...
-
Pursuing Analytically the Influence of Hearing Aid Use on Auditory Perception in Various Acoustic Situations
PublicationThe paper presents the development of a method for assessing auditory perception and the effectiveness of applying hearing aids for hard-of-hearing people during short-term (up to 7 days) and longer-term (up to 3 months) use. The method consists of a survey based on the APHAB questionnaire. Additional criteria such as the degree of hearing loss, technological level of hearing aids used, as well as the user experience are taken...
-
Conditions for Multiple Acquisition of Echoes from Stationary Targets in Successive Transmissions of Active Sonars
PublicationIn echolocation, the highest possible number of contacts with a detected target is clearly decisive on the possibilities of echo processing to optimise the estimation of distinctive characteristics of the observed target. In hydrolocation, the slow propagation of acoustic waves in water reduces the number of contacts of echosounders and sonars with detected targets. The article considers model conditions for acquiring multiple...
-
Method for the correlation coefficient estimation of the bottom echo signal in the shallow water application using interferometric echo sounder
PublicationThe article presents a new method for the assessment of bottom echo correlation coefficient in the presence of multiple echoes. Bottom correlation coefficient is a parameter that characterizes spatial properties of echo signal. Large variability of the bottom shape or properties (for example caused by the presence of bottom objects) and the presence of the acoustic shadow strongly influence the value of the correlation coefficient....
-
Timber-frame house resistant to dynamic loads - analysis of wall panel filled with polyurethane foam
PublicationThe present study shows the experimentally and numerically determined response of a single timber-frame house wall panel filled with polyurethane (PU) foam under dynamic loads. The harmonic tests were conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified displacement. Based on the results of the comparison between the experimental tests and the numerical analyses, the numerical...
-
Underwater acoustic communication system using broadband signal with hyperbolically modulated frequency
PublicationThe implementation of reliable acoustic underwater communication in shallow waters is a scientific and engineering challenge, mainly due to the permanent occurrence of the multipath phenomenon. The article presents the concept of a transmission system using a broadband signal with hyperbolically modulated frequency (HFM) to transmit data symbols and synchronize data frames. The simulation tests were carried out in channels with...
-
A New Direct-Sequence Spread Spectrum Signal Detection Method for Underwater Acoustic Communications in Shallow-Water Channel
PublicationDirect-Sequence Spread Spectrum (DSSS) is one of the modulation and coding techniques used in Underwater Acoustic Communication (UAC) systems for reliable data transmision even at low signal levels. However, in a shallow water channel, there is a strong multipath propagation which causes a phase fluctuation of the received signal, affecting the performance of the spread-spectrum system. The article presents a differential method...
-
Simulation of Direct-Sequence Spread Spectrum Data Transmission System for Reliable Underwater Acoustic Communications
PublicationUnderwater acoustic communication (UAC) system designers tend to transmit as much information as possible, per unit of time, at as low as possible error rate. It is a particularly difficult task in a shallow underwater channel in which the signal suffers from strong time dispersion due to multipath propagation and refraction phenomena. The direct-sequence spread spectrum technique (DSSS) applied successfully in the latest standards...
-
Performance of Coherent Modulation Scheme Used in Acoustic Underwater Communication System
PublicationThe development of an acoustic underwater communication system for shallow waters is still a big scientificand construction challenge. Currently, non-coherent modulations in combination with strong channel coding are used to achieve reliable communication with low rate in such a channel. To obtain transmission with a higher transmission rate, it is required to use coherent modulation. This paper presents the assumptions of such...
-
The effect of fishing basin construction on the behaviour of a footbrdge over the port channel
PublicationThe paper analyses possible causes of failure of the rotating footbridge over the Ustka port channel. In July, 2015, strange behaviour of this object was observed in the form of excessive vibrations of bridge platform suspension rods, with the accompanying acoustic effects. A preliminary geotechnical analysis has revealed that this destructive effect was caused by the nearby construction works, namely construction of a fishing...
-
The influence of Be addition on the structure and thermal properties of alkali-silicate glasses
PublicationBe-Na-(Li)-Si oxide glasses containing up to 15 mol% of BeO were prepared. Their structure was characterized by X-ray powder diffraction and Raman as well as infrared spectroscopic techniques, while their chemical compositions were examined by Inductively Coupled Plasma Optical Emission Spectrometry. All materials were found to be amorphous and contain Al contaminations from minor dissolution of the alumina crucibles. The results...
-
A pilot study to assess manufacturing processes using selected point measures of vibroacoustic signals generated on a multitasking machine
PublicationThe article presents the method for the evaluation of selected manufacturing processes using the analysis of vibration and sound signals. This method is based on the use of sensors installed outside the machining zone, allowing to be used quickly and reliably in real production conditions. The article contains a developed measurement methodology based on the specific location of microphones and vibration transducers mounted on...
-
On dynamic modeling of piezomagnetic/flexomagnetic microstructures based on Lord–Shulman thermoelastic model
PublicationWe study a time-dependent thermoelastic coupling within free vibrations of piezomagnetic (PM) microbeams considering the flexomagnetic (FM) phenomenon. The flexomagneticity relates to a magnetic field with a gradient of strains. Here, we use the generalized thermoelasticity theory of Lord–Shulman to analyze the interaction between elastic deformation and thermal conductivity. The uniform magnetic field is permeated in line with...
-
Manganese(II) tri-tert-butoxysilanethiolate complexes with imidazole based coligands. A neutral complex with four independent ligands and MNOS2 core (M=Mn) related to the liver alcohol dehydrogenase catalytic center (M=Zn)
PublicationReakcja silanotiolanu manganu(II) z imidazolem oraz dwiema jego metylowymi pochodnymi prowadzi do uzyskania kompleksów heteroleptycznych o różnym typie. Gdy do syntez wykorzystano 2-metyloimidazol uzyskano związek zawierający w komórce elementarnej dwie różniące się od siebie cząsteczki, powiązane wiązaniami wodorowymi typu N-H…S. W jednej z tych molekuł centralny atom manganu jest skoordynowany z czterema ligandami: dwoma podstawnikami...
-
Evolution of artificial single-cell organisms foraging for resources in a 3-dimensional environment
PublicationForaging for resources is a simple cognitive task that even one-celled biological organisms can ac- complish. We present an Artificial Life system in which artificial unicellular organisms (animats) forage for food in a 3-dimensional simulated liquid environment. The movement of animats is controlled by evolving artificial gene regulatory networks encoded in linear genomes. When an animat consumes enough food, it produces offspring...
-
Characterization of corrosion in reinforced concrete beams using destructive and non-destructive tests
PublicationThe paper presents both non-destructive and destructive experimental tests on steel-reinforced concrete beams subjected to electrochemical corrosion. To examine the condition and behavior of the specimens, destructive tests were carried out, i.e., a three-point bending together with a modulated ultrasonic wave test. In addition, a series of non-destructive experiments were conducted, such as the potential measurement method, low-frequency...
-
Polymeric Bearings – A New Base Isolation System to Reduce Structural Damage during Earthquakes
PublicationBase isolators, like lead rubber bearings, high damping rubber bearings or friction pendulum systems are extensively used in practice in many seismically active regions to protect structures against earthquake forces. The present paper reports the results obtained from the experimental study aimed to determine the effectiveness of the Polymeric Bearings in suppressing structural vibrations during dynamic excitations and therefore...
-
Behaviour of Asymmetric Structure with Base Isolation Made of Polymeric Bearings
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. Due to randomness of earthquake occurrence, lack of visible causes and their power of destructiveness, structural engineers need to develop new technical solutions and protection systems against...
-
Reactions of (Ph)tBuP-P(SiMe3)Li·3THF with [(PNP)TiCl2] and [MeNacNacTiCl2·THF]. Synthesis of first PNP titanium(IV) complex with phosphanylphosphinidene ligand [(PNP)Ti(Cl){η2-P-P(Ph)tBu}]
PublicationLithium derivative of diphosphane (Ph)tBuP-P(SiMe3)Li (1) was isolated for the first time and investigated in reactions with β-diketiminate (MeNacnac− = [Ar]NC(Me)CHC(Me)N[Ar]; Ar = 2,6-iPr2C6H3) and PNP-pincer (PNP = N[2-PiPr2-4-methylphenyl]2) Ti(III) complexes. The β-diketiminate titanium(III) complex containing phosphanylphosphido ligand [MeNacNacTi(Cl){η2-P(SiMe3)-P(Ph)tBu}] (2) was prepared in reaction of [MeNacNacTiCl2·THF]...
-
The Method of reduction of aerodynamic forces generated in turbine blade seals
PublicationThe distibution of pressure in the seal gaps does not only affect the so called '' leakage losses'' and the turbine stage overall efficiency but also plays an important role in the generation of aerodynamic forces which may cause self-excited rotor vibrations. The paper describes a chamber seal applied for the reduction of the aerodynamic forces created in shroud seals. This kind of turbine seal was patented and tested.
-
Experimental study on earthquake-induced pounding between steel structures
PublicationPounding between adjacent structures has been repeatedly observed during major earthquakes. The phenomenon may cause some local damage at the points of interactions, it may also lead to substantial destruction, permanent deformations or total collapse of colliding structures. The effects of earthquake-induced structural pounding have been studied for more than three decades now. However, most of the studies concerned masonry as...
-
Bending analysis of functionally graded nanoplates based on a higher-order shear deformation theory using dynamic relaxation method
PublicationIn this paper, bending analysis of rectangular functionally graded (FG) nanoplates under a uniform transverse load has been considered based on the modified couple stress theory. Using Hamilton’s principle, governing equations are derived based on a higher-order shear deformation theory (HSDT). The set of coupled equations are solved using the dynamic relaxation (DR) method combined with finite difference (FD) discretization technique...
-
Finite-element analysis of a base-isolated multi-storey steel building under seismic motions
PublicationNumerical simulation of the seismic behaviour of a multi-storey steel building, both fixed-base and base-isolated, under the 1940 El Centro earthquake was performed in this paper. The analyzed 4-storey building was decoupled from the shaking ground with the Polymeric Bearings, which can be considered a proposal of a new seismic isolation system. It consists of rectangular-shaped blocks made of a specially prepared flexible polymeric...
-
Lower rim substituted tert-butylcalix[4]arenes (II). Complexing ability of5,11,17,23-tetra-tert-butyl-25,26,27,28-tetrakis-O-(piperidinylcarbonyl)me- thylenecalix[4]arene. The crystal structures of the ligand and its sodium complex
PublicationSyntezowano kompleksy wymienionego w tytule liganda z chlorkiem sodu i azotanami itru(III), lantanu(III), samaru(III) i gadolinu(III) w reakcji liganda i odpowiedniej soli, które charakteryzowano za pomocą widm IR, UV-vis,1H NMR, FAB-MS, a także za pomocą analizy elementarnej. W reakcji wymiany z kompleksu z sodem otrzymywano kompleksy z lantanowcami. Określono strukturę krystaliczną wolnego liganda i jego kompleksu z sodem za...
-
Zespół mieszkaniowo-usługowy ZUS przy ul. Partyzantów w Gdyni, jako przykład nowoczesnego zintegrowania funkcji i formy = / ZUS residential and service complex in Partyzantów St. in Gdynia as an example of modern integration of form and function
PublicationArtykuł dotyczy zespołu zabudowy, który powstał w Gdyni pod koniec lat 30. XX w. Ukończenie założenia przerwał wybuch II wojny, ale pomimo tego zrealizowana część dowodzi, że zastosowane rozwiązania przestrzenne i funkcjonalne należały do najnowocześniejszych w ówczesnej Polsce.
-
Numerical solutions for large deformation problems in geotechnical engineering
PublicationThe problem of large deformations often occurs in geotechnical engineering. Numerical modeling of such issues is usually complex and tricky. The chosen solution has to implicate soil-soil and soil-structure interactions. In this paper, a review of the most popular numerical methods for large deformation problems is presented. The Coupled Eulerian-Lagrangian (CEL) method, the Arbitrary Lagrangian-Eulerian (ALE) method, the Smoothed...
-
Experimental dynamic study on a timber-frame house using shaking table
PublicationThe aim of this paper is to show the results of the shaking table experimental study concerning the behaviour of the model of the timber-frame house under earthquake excitation and impact loading. In order to determine the basic dynamic properties of the undamaged structure, the free vibration and the sweep-sine tests were first conducted. Then, the model was excited using the time history record of the El Centro earthquake of...
-
Optimization of the spindle speed during milling of large-sized structures with the use of technique of Experiment-Aided Virtual Prototyping
PublicationIn the paper are presented considerations concerning vibration suppression problems during milling of large-sized workpieces with the use of innovative method of matching the spindle speed of cutting tool. It depends on repeatable change of the spindle speed value as soon as the optimal vibration state of the workpiece approaches. The values of dominant “peaks” in the frequency spectra and the Root Mean Square (RMS) values of time...
-
Experimental Study on Effectiveness of a Prototype Seismic Isolation System Made of Polymeric Bearings
PublicationSeismic isolation is identified as one of the most popular and effective methods of protecting structures under strong dynamic excitations. Base isolators, such as Lead Rubber Bearings, High Damping Rubber Bearings, and Friction Pendulum Bearings, are widely used in practice in many earthquake-prone regions of the world to mitigate structural vibrations, and therefore minimize loss of life and property damage during seismic events....
-
Analysis of Modal Parameters Using a Statistical Approach for Condition Monitoring of the Wind Turbine Blade
PublicationThe primary objective of the presented paper is the numerical and experimental investigation related to developing a useful diagnostic method, which can be used for determining the site and size of damage in laminated shells of wind turbine blades. The described detection technique is based on the analysis of low frequencies bending vibrations mode shapes of rotor blades. The authors used the commonly applied statistics methods...
-
Nonlinear generation of non-acoustic modes by low-frequency sound in a vibrationally relaxing gas
PublicationTwo dynamic equations referring to a weakly nonlinear and weakly dispersive flow of a gas in which molecular vibrational relaxation takes place. are derived. The first one governs an excess temperature associated with the thermal mode, and the second one describes variations in vibrational energy. Both quantities refer to non-wave types of gas motion. These variations are caused by the nonlinear transfer of acoustic energy into...
-
FT-IR studies of molecular interactions in formamide-methanol mixtures
PublicationTechniką ATR zmierzono widma FT-IR roztworów metanolu(MeOH) i formamidu(FA) w całym zakresie ich składu. Przeprowadzono analizę faktorową widm, która wykazała obecność dwóch kompleksów molekularnych matanolu z formamidem. Na podstawie profilów stężeniowych indywiduów absorbujących wyznaczono średni skład kompleksów w zależności od składu mieszaniny. Przeprowadzono również analizę pasma CO formamidu metodą widm różnicowych. Wyniki...