Search
Filters
total: 305
filtered: 271
Search results for: CHROMIUM EVAPORATION
-
Mn-Co spinel coatings on Crofer 22 APU by electrophoretic deposition: Up scaling, performance in SOFC stack at 850 °C and compositional modifications
PublicationCeramic coatings for metallic interconnects play a key role in limiting corrosion and chromium evaporation in solid oxide cells. This study presents the upscaling of the electrophoretic deposition (EPD) technique to process Mn-Co spinels on real-dimension Crofer 22 APU interconnects and the test in a SOFC stack. Area specific resistance of long-term test conducted for 5000 h at 850 °C demonstrated that two-steps sintering has a...
-
Low temperature processed MnCo2O4 and MnCo1.8Fe0.2O4 as effective protective coatings for solid oxide fuel cell interconnects at 750 °C
PublicationIn this study two materials, MnCo2O4 and MnCo1.8Fe0.2O4 are studied as potential protective coatings for Solid Oxide Fuel Cell interconnects working at 750 °C. First powder fabrication by a modified Pechini method is described followed by a description of the coating procedure. The protective action of the coating applied on Crofer 22 APU is evaluated by following the area specific resistance (ASR) of the scale/coating for 5500...
-
Experimental review of the performances of protective coatings for interconnects in solid oxide fuel cells
PublicationFerritic stainless steel interconnects are used in solid oxide fuel cells; however, coatings are required to improve their performance. Although several types of coatings have been proposed, they have been scarcely investigated under similar conditions. This study compares the characteristics of uncoated Crofer 22 APU and eight different coatings on Crofer 22 APU for up to 3000 h at 800 ◦C. The coatings were deposited at various...
-
Suspension and process parameters selection for electrophoretic deposition of Mn–Co spinel coating on steel interconnects
PublicationMetallic interconnect coatings, consisting of MnCo2O4 spinel, were effectively applied to Crofer 22 APU using the electrophoretic deposition (EPD) method in both H2O: ethanol and pure ethanol solvents. The primary goal of this method was to prevent chromium migration, minimize evaporation, and control the oxidation rate. The study aimed to assess the quality, adhesion, and thickness of the Mn–Co coating, with the objective of...
-
EFFECT OF NANOFLUID CONCENTRATION ON TWO-PHASE THERMOSYPHON HEAT EXCHANGER PERFORMANCE
PublicationAn approach – relaying on application of nanofluid as a working fluid, to improve performance of the two-phase thermosyphon heat exchanger (TPTHEx) has been proposed. The prototype heat exchanger consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. Distilled water and nanofluid water-Al2O3...
-
High-temperature Corrosion of ~ 30 Pct Porous FeCr Stainless Steels in Air: Long-Term Evaluation Up to Breakaway
PublicationIn this work, a long-term (up to 6000 hours) corrosion evaluation of three porous (~ 30 pct of initial porosity) ferritic iron-chromium alloys with different Cr contents (20, 22, and 27 wt pct of Cr) was carried out at 600 C, 700 C, 800 C, and 900 C in air. Mass gain measurements and SEM analyses revealed that at temperatures above 600 C, all alloys exhibit breakaway corrosion, whereas at 600 C, none of the alloys were heavily...
-
Structural and electrical properties of Cr-doped SrTiO 3 porous materials
PublicationSeries of single-phase materials with assumed formula SrTi1−xCrxO3 (where x = 0, 1, 4, 6 mol.%) were obtained by sol-gel method. The structure and microstructure of materials were characterised by X-ray diffraction and scanning electron microscopy methods. Moreover, the study of electrical properties and evaluation of chemical stability in CO2/H2O atmosphere was performed by electrochemical impedance spectroscopy and thermogravimery...
-
Optimization and Modeling of Cr (VI) Removal from Tannery Wastewater onto Activated Carbon Prepared from Coffee Husk and Sulfuric Acid (H2SO4) as Activating Agent by Using Central Composite Design (CCD)
PublicationThe primary goal of this research is to lower the hexavalent chromium (Cr (VI)) concentration that has occurred from the growth of the tannery industry. As a result, the potential for heavy metal concentration is increasing day by day. Industrial effluent containing Cr (VI) contributes significantly to water pollution. Chromium hexavalent ion (Cr (VI)) in wastewater is extremely hazardous to the environment. It is critical to address...
-
Comparison of heat transfer characteristics in surface cooling using microjets with water, ethanol and HFE7100 as test fluids
PublicationAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the dimensions of the size of nozzle leads to an increase in the economy of cooling and improves its quality. Present study describes research related to the design and construction of the nozzles and microjet study, which may be applied in many technical applications such as in metallurgy, electronics, etc....
-
CuMn1.7Fe0.3O4 – RE2O3 (RE=Y, Gd) bilayers as protective interconnect coatings for Solid Oxide Cells
PublicationEfficient replacement of materials based on critical elements such as cobalt is one of the greatest challenges facing the field of solid oxide cells. New generation materials, free of cobalt show potential to replace conventional materials. However, these materials are characterized by poor ability to block chromium diffusion. This article described the study of CuMn1.7Fe0.3O4 (CMFO) spinel combined with single metal oxide (Y2O3...
-
Społeczni, ale czy przedsiębiorczy? Gotowość organizacji pozarządowych do ekonomizacji
PublicationW artykule autorki podejmują dyskusję czy i w jakim stopniu organizacje pozarządowe są przygotowane do ekonomizacji. W artykule wyodrębniono i określono zjawisko ekonomizacji, zidentyfikowano czynniki sprzyjające temu procesowi, prowadzące do rozwoju przedsiębiorczości społecznej: potrzebę zapewnienia stabilności finansowej i niezależności organizacji pozarządowych od innych podmiotów (w tym głównie administracji publicznej). Autorki...
-
A Multi Rig Screening Test for Thin Ceramic Coatings in Bio - Tribological Applications
PublicationA method is presented for the comparative testing of wear resistance of ceramic coatings made from materials potentially feasible in tribo - medical applications, mainly orthopaedic implants made from ceramics coated metals for low cost, long life and low wear particle emission into the body. The method was devised as the main tool for use in research and is comprised of flat on flat and ball on flat surface (sliding) tests. Seven...
-
Possibilities of Increasing the Overall Efficiency of Gas-steam CHP Microplant
PublicationThe paper presents ways to increase the efficiency of a gas-steam micro power plant by modifying the cycle combination. The modification consists in partial release of the fluid downstream of the gas turbine and using it for ORC fluid overheating and evaporation. Advantages of this solution over the simplest gas and steam cycles’ combination are demonstrated.
-
Inlet air fogging of marine gas turbine in power output loss compensation
PublicationThe use of inlet air fogging installation to boost the power for gas turbine engines is widely applied in the power generation sector. The application of fogging to mechanical drive is rarely considered in the literature [1]. This paper will cover some considerations relating to its application to gas turbines in ship drive. There is an important evaporative cooling potential throughout the world when the dynamic data is evaluated,...
-
Preparation of Hydrogen Electrodes of Solid Oxide Cells by Infiltration: Effects of the Preparation Procedure on the Resulting Microstructure
PublicationIn this work, the infiltration technique was used to produce hydrogen electrodes for solid oxide cells. Different infiltration methodologies were tested in order to try to shorten the infiltration cycle time. The porous scaffolds used for infiltration were based on highly porous yttria-stabilized zirconia (YSZ) obtained by etching the reduced nickel from the Ni-YSZ cermet in HNO3 acid. The support had a complex structure which...
-
Annual variability of heavy metal content in Svalbard reindeer faeces as a result of dietary preferences
PublicationDuring both winter and summer, Svalbard reindeer selectively feed on different types of vegetation that are not only a source of nutritional value, but also a place of heavy metal accumulation. In the present study, the content of cadmium, chromium, copper, iron, lead, nickel, manganese, and zinc in reindeer excrement was measured. The main aims were to determine the seasonal content of several heavy metals in Svalbard reindeer...
-
Experimental Investigation of the Thermal Performance of a Wickless Heat Pipe Operating with Different Fluids: Water, Ethanol, and SES36. Analysis of Influences of Instability Processes at Working Operation Parameters
PublicationIn this study, the influences of different parameters on performance of a wickless heat pipe have been presented. Experiments have been carried out for an input power range from 50 W to 300 W, constant cooling water mass flow rate of 0.01 kg/s, and constant temperature at the inlet to condenser of 10 C. Three working fluids have been tested: water, ethanol, and SES36 (1,1,1,3,3-Pentafluorobutane) with different filling ratios (0.32,...
-
Determination of causes of accelerated local corrosion of austenitic steels in water supply systems
PublicationThis paper concerns an inspection of a water supply system, made of AISI 304 steel, which showed signs of local corrosion at the weld. Such corrosion caused material perforation after very short periods of operation. It was revealed that steel was sensitised during the welding process. It was also proven that chromium micro-segregation occurred in the alloy leading to galvanic cell formation which initialised the process of pitting...
-
Zanieczyszczenie metalami ciężkimi osadów dennych małych miejskich zbiorników wodnych.
PublicationW pracy przedstawiono badania zawartości sześciu metali ciężkich (cynku, miedzi, ołowiu, niklu, chromu i kadmu) w osadach dennych zbiorników miejskich zlokalizowanych w Gdańsku. Wyniki wskazują na znaczne różnice w zawartości metali w osadach różnych zbiorników zależnie od ich lokalizacji. Zawartość cynku wahała się w zakresie 31,9÷254,4 mg/kg s.m., miedzi 5,20÷338,5 mg/kg s.m., ołowiu 10,3÷103,7 mg/kg s.m., niklu 5,9÷17,5 mg/kg...
-
Właściwości złączy różnoimiennych stopu niklu Incoloy 800H ze stalą odporną na korozję 316L
PublicationW artykule przedstawiono problemy związane z wykonywaniem połączeń różnoimiennych typu Incoloy 800HT – austenityczna stal odporna na korozję 316L. Wykonano badania nieniszczące oraz niszczące, których wyniki pozwoliły na weryfikacje jakości wykonanych złączy próbnych. Nie stwierdzono występowania niezgodności spawalniczych oraz uzyskano wysokie właściwości wytrzymałościowe złączy. Badania metalograficzne ujawniły poprawne struktury...
-
Self-assembled concentric stripes of diamond particles by a pinning-depinning mechanism
PublicationWe describe the novel mechanism of spontaneous formation of the concentric stripe patterns of microdiamonds via gradual solvent evaporation from a suspension confined in a teardrop well. The self-organized patterns exhibit a series of arcs with regular spacings varying between hundreds of micrometers and millimeters. They result from an interplay between the directional forced circulation of the solvent and a stick-slip movement...
-
Interaction of yttria stabilized zirconia electrolyte with Fe2O3 and Cr2O3
PublicationW pracy przedstawiono badania interakcji pomiędzy domieszkowanym tlenkiem cyrkonu a tlenkiem chromu i tlenkiem żelaza. Tlenek chromu wpływa głównie na zwiększenie rezystacji granic międzyziarnowych, zaś tlenek żelaza zwiększa zarówno rezystancje ziaren jak i granic międzyziarnowych.
-
High temperature corrosion evaluation and lifetime prediction of porous Fe22Cr stainless steel in air in temperature range 700–900 °C
PublicationThis work describes a high temperature corrosion kinetics study of ~30% porous Fe22Cr alloys. The surface area of the alloy (~0.02 m2 g-1) has been determined by tomographic microscopy. The weight gain of the alloys was studied by isothermal thermogravimetry in the air for 100 hours at 700 - 900 °C. Breakaway oxidation was observed after oxidation at 850 °C (~100 hours) and 900 °C (~30 hours). The lifetime prediction shows the...
-
Aspects of intergranular corrosion of AISI 321 stainless steel in high-carbon-containing environments
PublicationPurpose – The purpose of this paper is to present a case study of unexpected sensitization to intergranular corrosion of highly resistant AISI 321 steel in petrochemical conditions, where it was subjected to the simultaneous influence of elevated temperature of 250°C and vapors from the asphalt production process. Design/methodology/approach – Corrosion coupons were exposed in an installation carrying asphalt vapors. To identify...
-
Emerging oxidized and defective phases in low-dimensional CrCl3
PublicationTwo-dimensional (2D) magnets such as chromium trihalides CrX3 (X ¼ I, Br, Cl) represent a frontier for spintronics applications and, in particular, CrCl3 has attracted research interest due its relative stability under ambient conditions without rapid degradation, as opposed to CrI3. Herein, mechanically exfoliated CrCl3 flakes are characterized at the atomic scale and the electronic structures of pristine, oxidized, and defective...
-
Pre-oxidation of porous ferritic Fe22Cr alloys for lifespan extension at high-temperature
PublicationPre-oxidation of porous ferritic Fe22Cr alloys was extensively studied in this paper. Weight gain measurements and SEM analysis revealed that pre-oxidation performed at 900◦C for 40 min increased the lifespan of the alloy. A Cr evaporation study did not disclose any significant influence of the pre-oxidation process on the Cr content in the alloy. For a more detailed assessment, TEM imaging and X-ray tomography measurements of...
-
Flow Boiling in Minigap in the Reversed Two-Phase Thermosiphon Loop
PublicationThe paper presents the results of experimental investigations of a model of a heat exchanger featuring a minigap, which is perceived as an evaporator for an inverted thermosiphon. The system works with a single component test fluid. The tested evaporator generates pumping power in the test loop in a way similar to the mammoth pump. The tests regarded a module of the heat exchanger, consisting of a hot leg and a cold leg with the...
-
Synthesis, structural characterization, and thermal properties of Ca‐ and La‐doped soda‐lime glasses by laser melting
PublicationLaser melting techniques have been used in the preparation of unconventional glass compositions with high melting temperatures. Thus, we wanted to test the feasibility of using a CO2 laser in the preparation of nitrogen-rich oxynitride glasses and nitride silicate glasses. Melting from oxides and metallic raw materials, we wanted to study first glass formation and possible evaporation losses of the glass components. Two glass series...
-
Raport dotyczący wyników badań w zakresie diagnozy ekonomii społecznej w mieście Gdynia. Od ekonomii społecznej do przedsiębiorczości społecznej.
PublicationEkspertyza jest dotyczy wyników badań wykonanych na zlecenie MOPS w Gdyni, na temat ekonomii społecznej i przedsiębiorczości społecznej w mieście Gdynia.
-
KU GDYŃSKIEMU EKOSYSTEMOWI. Refleksje badawcze na podstawie diagnozy ekonomii społecznej w Gdyni.
PublicationW raporcie przedstawiono podsumowanie wniosków i rekomendacji dla miasta Gdynia w zakresie rozwoju przedsiębiorczości społecznej i ekonomii społecznej
-
Analysis of features of stainless steels in dissimilar welded joints in chloride inducted corrosion
PublicationStainless steels of femtic-austenitic microstructure that means the duplex Cr-Ni-Mo steels, in comparison with austenitic steel includes less expensive nickel and has much better mechanical properties with good formability and corrosion resistance, even in environments containing chloride ions. Similar share of high chromium ferrite and austenite, which is characterized by high ductility, determines that the duplex steels have...
-
NEW ORGANIC MATERIALS FOR PHOTOVOLTAICS
PublicationThis report presents the results of investigations carried out for polymer- and low-weightmolecular materials prepared in the form of thin films by various methods, namely the thermalvacuum evaporation and chemical vapour deposition. The influence of the technologicalconditions on the structure, surface morphology, and electronic properties of selected organic thinfilms, including polyazomethines, phthalocyanines, and perylene...
-
Effects of La Content on the Densification, Microstructure, and Conductivity of Doped La10−x Ge6 O26±δ Electrolytes
PublicationIn this study, the influence of La content on the characteristics of Nb-, Mo-, and W-doped LaxGe6O26±δ electrolytes was investigated through sintering study, X-ray diffraction, scanning electron microscopy, and conductivity measurement. The densification of LaxGe5.5Nb0.5O26±δ and LaxGe5.5W0.5O26±δ was retarded as the x reached 9.75, while that of LaxGe5.5Mo0.5O26±δ improved with increasing La content. The average grain size slightly...
-
SAFE - technika izolacji związków zapachowych z próbek żywności
PublicationOznaczanie składników odpowiedzialnych za zapach produktów żywnościowych dokonywane za pomocą technik chromatograficznych obejmuje dwa zasadnicze etapy: przygotowanie próbki i identyfikację (rozdzielenie połączone z odpowiednią metodą detekcji). Ze względu na skomplikowaną matrycę, specyfikę związków zapachowych - samoistne ich uwalnianie z matrycy, jak i możliwość zachodzenia przemian, kluczowym elementem analizy żywności jest...
-
Comparison of heat transfer characteristics in surface cooling with boiling microjets of water, ethanol and HFE7100
PublicationThe basis of microjet technology is to produce jets which impinge the surface at the stagnation point with a very high kinetic energy. Main objective of this paper was to investigate the physical phenomena occurring on solid surfaces upon impingement of the single microjet in case of three fluids, namely water, ethanol and HFE7100. Intense heat transfer in the impact zone of microjet has been examined and described with precise...
-
Interplay of hydrogen bonding and aryl-perfluoroaryl interactions in construction of supramolecular aggregates
PublicationThe stacking between aryl and perfluoroaryl units is an important class of the aromatic – aromatic interactions that has attracted rapidly growing interest in recent years. Continuing interest of our group in this subject it had been prepared three new complexes of pentafluorobenzoic acid with benzyl alcohol, 4-methylbenzyl alcohol and 4-tert-butylbenzyl alcohol and in the next step investigated their self-assembly modes by...
-
BIOMATERIALS AND IMPLANTS IN CARDIAC AND VASCULAR SURGERY - REVIEW
PublicationCurrently, on prosthesis in cardiac blood vessels and heart valves are used materials of animal or synthetic origin. For animal materials include, among others pericardial sac in which is the heart. Materials such as this (natural) are characterized by a remarkable biocompatibility within the human body, but their main disadvantage is the relatively low durability. In turn, synthetic materials, which include the austenitic chromium-nickel-molybdenum...
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublicationIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Alternative cogeneration thermodynamic cycles for domestic ORC
PublicationThe Organic Flash Cycle (OFC) is suggested as a vapor power cycle that could potentially improve the efficiency of utilization of the heat source. Low and medium temperature finite thermal sources are considered in the cycle. Additionally the OFC’s aim is to reduce temperature difference during heat addition. The study examines 2 different fluids. Comparisons are drawn between the OFC and an optimized basic Organic Rankine Cycle...
-
Wpływ podwyższonych temperatur na napawane warstwy na bazie kobaltu = The elevated temperatures influence on the cobalt base cladding layer
Publicationw pracy przeanalizowano wpływ temperatur utleniania (850, 950 i 110 stopni C) na mikrostrukturę i twardośc napawanych plazmowo warstw zykonanych z proszku na bazie kobaltu zdodatkiem 28,8% chromu, 4,9% wolframu, 2,2% niklu, 2,09% żelaza, 1,2% krzemu i 1,2% węgla. W wyniku utleniania na powierzchni napoiny powstaje warstwa tlenku chromu stanowiaca dobrą ochronę w niższych temperaturach, jednak w temperaturach wyższych ulega ona...
-
Investigation of the influence of capilary effect on operation of the loop heat pipe
PublicationIn the paper presented are studies on the inestigation of the capillary forces effect inducted in the porous structure of a loop heat pipe using water and ethanol ad test fluids. The potential application of such effects is for example in the evaporator of the domestic micro-CHP unit, where the reduction of pumping power could be obtained. Preliminary analysis of the results indicates water as having the best potential for developing...
-
FEM approach to modeling of an irregular trabecular structure
PublicationThe aim of the study is elaboration of a method for creating irregular scaffolds that can be used to model the behaviour of trabecular bone placed in the proximal epiphysis of the femur. The scope of the study encompasses creating six numerical models of irregular scaffolds (two solid irregular scaffolds, two shell irregular scaffolds and two shell irregular scaffolds with fortification) and performing numerical analysis of the...
-
A study of a reduction of a micro- and nanometric bismuth oxide in hydrogen atmosphere
PublicationA reduction of bismuth oxide in hydrogen atmosphere was investigated. The reaction was performed with a material in various structural forms: powder: with micrometric grains, powder with nanometric grains and powder pressed into pellets. The process was performed in both isothermal and non-isothermal conditions. An activation energy of the reaction calculated with Friedman method was found to be about 85 kJ/mol for the reduction...
-
Effective yttrium based coating for steel interconnects of solid oxide cells: Corrosion evaluation in steam-hydrogen atmosphere
PublicationThis work describes manufacture, analysis and test of a new well conducting corrosion-protection coating that can be applied on steel types with high chromium content. Electrolytic deposition of yttrium salts is used to form thin (<100 nm) coatings on both flat steel sheets (material: Crofer 22 APU) and its properties are proven on woven wire-meshes (materials from two different sources: SUS316 and SUS316L). The oxide scale on...
-
Development of Microstructured Carbon Coatings by Substrate-Catalytic CVD
PublicationCarbon nanostructured films were synthesized by chemical vapor deposition (CVD) on H18 stainless steel (AISI 440C) sheets with an H2/CH4/N2 gas mixture at various substrate temperatures. During the synthesis, the iron and chromium oxide layer was formed between the steel and carbonaceous layer. The carbon films exhibited wall-like and spherical morphologies and structures, as characterized by scanning electron microscopy and Raman...
-
COMPARISON OF HEAT TRANSFER CHARACTERISTICS IN SURFACE COOLING WITH BOILING MICROJETS OF WATER, ETHANOL AND HFE7100
PublicationThe basis of microjet technology is to produce laminar jets which when impinging the surface have a very high kinetic energy at the stagnation point. Boundary layer is not formed in those conditions, while the area of film cooling has a very high turbulence resulting from a very high heat transfer coefficient. Applied technology of jet production can result with the size of jets ranging from 20 to 500μm in breadth and 20 to 100μm...
-
Accumulation of radioisotopes and heavy metals in selected species of mushrooms
PublicationSeven species of forest mushrooms from different regions of Poland (edible: Imleria badia, Cantharellus cibarius, Xerocomus subtomentosus, Suillus luteus and inedible by humans but being food for animals: Paxillus involutus, Tylopilus felleus and Russula emetica) were analyzed for radioisotope activity (Cs-137, K-40, Bi-214 and Pb-210) as well as concentrations of heavy metals (aluminum, chromium, cadmium, manganese, iron, lead,...
-
Determination of dryout localization using a five-equation model of annular flow for boiling in minichannels
PublicationDetailed studies have suggested that the critical heat flux in the form of dryout in minichannels occurs when the combined effects of entrainment, deposition, and evaporation of the film make the film flow rate go gradually and smoothly to zero. Most approaches so far used the mass balance equation for the liquid film with appropriate formulations for the rate of deposition and entrainment respectively. It must be acknowledged...
-
Ceramic composites for single-layer fuel cells
PublicationComposite materials consisting of acceptor doped lanthanum orthoniobate electrolyte phase (La0.98Ca0.02NbO4) and Li2O:NiO:ZnO semiconducting phase were synthesized. The precursor powder of La0.98Ca0.02NbO4 was prepared in nanocrystalline (mechanosynthesis) and microcrystalline (solid-state synthesis) form. The composite can be applied in a single-layer fuel cell, because of the presence of two phases acting as an anode and a cathode...
-
A LABORATORY STAND FOR THE ANALYSIS OF DYNAMIC PROPERTIES OF THERMOCOUPLES
PublicationIn the present elaboration, problems connected with measurements of high variable temperatures of gases are introduced and the impact of dynamic properties of different construction solutions of thermoelements on the accuracy of the measurements is considered. A laboratory stand built within research under doctoral thesis, destined for analysis of dynamic properties of thermocouples is also described. Results of numerical simulation...