Filters
total: 602
filtered: 412
Search results for: BI5FETI3O15 CERAMICS
-
Study of Phase and Chemical Composition of Bi1-xNdxFeO3 Powders Derived by Pressureless Sintering
PublicationIn the present paper studies on Bi1xNdxFeO3 for x =0.1-0.4 are reported. The mixed oxide method followed with pressureless sintering was employed for ceramics fabrication. Thermal behavior of stoichiometric mixtures of simple oxide powders, viz. Bi2O3, Nd2O3 and Fe2O3 was studied by simultaneous thermal analysis. It was found that with an increase in neodymium content the weight loss increased from 0.75% to 3.16% for x =0.1 and...
-
Materiały ceramiczne w łożyskach ślizgowych
PublicationOpisano obszary zastosowań ceramiki maszynowej w węzłach ślizgowych maszyn. Przedstawiono rodzaje ceramiki stosowane w łożyskowaniu ślizgowym. Przedstawiono produkowane fabrycznie ceramiczne łożyska ślizgowe.
-
Optymalizacja warunków pracy grubowarstwowych bolometrów LSFO
PublicationOpisano sposób produkcji bolometrów wykorzystujących ceramiczne, przewodzące warstwy typu perowskitu z niestechiometrycznych tlenków lantanowo-strontowo żelazowych (LSFO) wykonanych technologią LTCC (Low Temperature Co-fired Ceramics). Zaprezentowano wyniki pomiarów parametrów tych bolometrów oraz pozwalające na wybór optymalnych warunków pracy.
-
Effect of chemical composition on corrosion and wear behaviour of the composite Ni-Fe-Al2O3 coatings.
PublicationPrzedstawiono wyniki badań powłoki kompozytowej otrzymanej przez osadzanie katodowe galwaniczne w roztworze zawierającym sole niklu, żelaza oraz cząstki ceramiki Al2O3 o różnej wielkości i stężeniu. Wykazano, że charakterystyka ceramiki posiada wpływ na szybkość korozji i zużycia ściernego. W szczególności, zawartość ceramiki wpływa dodatnio na odporność na zużycie ścierne, ale nieco obniża odporność na zużycie korozyjne.
-
Barium boron aluminum silicate glass system for solid state optical gas sensors
PublicationRecent increasing demand for new eco-friendly materials and for low cost fabrication process for use in optical sensors field, raise concern about alternative materials for this application. We have designed two glass-ceramics compositions from the quaternary ROAl2O3- SiO2-B2O3(R=Ba) alkali-earth aluminum silicate system, labeled B72 and B69, with high refractive index (>1.6), large values of Abbe number (94.0 and 53.0, respectively),...
-
Gigantic electro-chemo-mechanical properties of nanostructured praseodymium doped ceria
PublicationSome oxygen defective fluorites are non-Newnham electrostrictors, i.e., the electromechanical response does not depend on their dielectric properties. Here, we show gigantic electrostriction in nanocrystalline 25 mol% praseodymium doped ceria (PCO) bulk ceramics. The material was fabricated with a fieldassisted spark plasma sintering (SPS) process from high-purity nanoscale PCO powders (<20 nm). The SPS process consolidates the...
-
Self-Organized Nanotubular Oxide Layers on Ti and Ti Alloys
PublicationTo improve bioactivity of titanium and titanium, the implant surface modification by formation of self-organized TiO2 nanotube arrays with electrochemical techniques is presented. The influence of electrolyte composition and deposition parameters during anodization is characterized. The enhancement of phosphates deposition by titanium nanotubular structure is discussed. The calcium phosphate ceramics is shown to be uniformly deposited...
-
Silicon oxycarbide-tin nanocomposite derived from a UV crosslinked single source preceramic precursor as high-performance anode materials for Li-ion batteries
PublicationIn this work, we report an innovative and facile UV light-assisted synthesis of a nanocomposite based on silicon oxycarbide (SiOC) and tin nanoparticles. SiOC ceramic matrix, containing a conductive free carbon phase, participates in lithium-ion storage, and buffers the volume changes of Li-alloying/de-alloying material. The reported synthesis procedure through a polymer-derived ceramic route involves the preparation of a single-source...
-
Modulation of dielectric properties in low-loss polypropylene-based composites at GHz frequencies: theory and experiment
PublicationPolymer composites with high dielectric constant and low loss tangent are highly regarded as substrates for modern high-speed electronics. In this work, we analyze the high-frequency dielectric properties of two types of composites based on polypropylene infused with high-dielectric-constant microparticles. Two types of fillers are used: commercial ceramics or titanium oxide ( TiO2) with different concentrations. The key observation...
-
Materiały stosowane do wytwarzania implantów kości
PublicationMateriały stosowane do wytwarzania implantów kostnych muszą być biokompatybilne, nietoksyczne, bioaktywne oraz wykazywać odpowiednie właściwości mechaniczne, takie jak wytrzymałość na ściskanie, na zginanie oraz sztywność i twardość. Gama stosowanych materiałów jest bardzo szeroka, obejmuje metale, polimery, ceramikę oraz ich kompozyty. Każdy z tych materiałów ma swoje mocne i słabe strony. Praca stanowi przegląd materiałów stosowanych...
-
THE POSSIBILITY OF USE OF LASER-MODIFIED Ti6Al4V ALLOY IN FRICTION PAIRS IN ENDOPROSTHESES
PublicationThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the Ti6Al4V alloy used for orthopedic applications. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. The paper presents the abrasive wear of the base and laser remelted material in association with ceramics Al2O3. Despite the surface cracking after laser treatment the...
-
Wpływ posuwu nagniatania na chropowatość powierzchni przedmiotów ze stali w stanie utwardzonym
PublicationPrzedstawiono wyniki badań eksperymentalnych procesu nagniatania stali twardej (62 HRC) narzędziem ceramicznym (kulką) z dociskiem hydrostatycznym. Analizowano wpływ posuwu nagniatania oraz parametrów poprzedzającej obróbki toczeniem na twardo na stan powierzchni opisanej wybranymi parametrami chropowatości.
-
Water uptake analysis of acceptor-doped lanthanum orthoniobates
PublicationIn this work, lanthanum orthoniobates doped with either antimony, calcium, or both have been synthesized and studied. The water uptake of the investigated materials has been analyzed by means of thermogravimetric studies. The results show the difference between the thermodynamics of hydration between the lanthanum orthoniobate system and other proton conducting ceramics. The relation between the water uptake and effective acceptor...
-
Mixed ionic-electronic conductivity and structural properties of strontium-borate glass containing nanocrystallites of Bi2 VO5.5
PublicationSamples of strontium borate glass containing bismuth vanadate nanocrystallites were prepared. Nanocomposites containing up to 45mol% of the Bi2VO5.5 phase exhibit electrical properties closer to the strontium-borate glass than to the ferroelectric Bi2VO5.5 ceramic. The glass matrix still may contain some part of bismuth and vanadium ions even after crystallization process and there is too little of crystalline phase to observe...
-
Investigation of electrocatalytic gas sensor properties in presence of chlorine
PublicationIn this paper performance of an electrocatalytic sensor in presence of chlorine is investigated. Presented studies concern sensor prepared in ceramic technology based on NASICON as a solid electrolyte with two round shaped platinum electrodes. Measurements in different temperatures have been performed in order to determine optimal sensor working temperature.
-
Stanowisko do pomiaru termicznej stałej czasowej bolometrów
PublicationPrzedstawiono stanowisko umożliwiające pomiar termicznej stałej czasowej bolometrów. Stanowisko to składa się z dwóch układów pomiarowych połączonych z cyfrowym analizatorem sygnału i umożliwia pomiar stałej czasowej w zakresie od pojedynczych milisekund do kilku sekund. Omówiono budowę i działanie opracowanych układów i zaprezentowano wyniki pomiarów stałej czasowej bolometrów z niestechiometrycznych tlenków lantanowo-strontowo-żelazowych...
-
Mn-Co spinel coatings on Crofer 22 APU by electrophoretic deposition: Up scaling, performance in SOFC stack at 850 °C and compositional modifications
PublicationCeramic coatings for metallic interconnects play a key role in limiting corrosion and chromium evaporation in solid oxide cells. This study presents the upscaling of the electrophoretic deposition (EPD) technique to process Mn-Co spinels on real-dimension Crofer 22 APU interconnects and the test in a SOFC stack. Area specific resistance of long-term test conducted for 5000 h at 850 °C demonstrated that two-steps sintering has a...
-
Assessment of Trace Metals Leaching During Rainfall Events from Building Rooftops with Different Types of Coverage – Case Study
PublicationRunoff water is an important medium transporting various types of pollution originating from the atmosphere and washed out from roofing materials. The study presents a quality assessment of runoff from different roofs in the context of trace metal concentrations. The analysed rooftops were covered with copper, tar paper and ceramic tile. The quality of the rain water collected at the same time satisfies the demands of the first...
-
CLAY MINERALS – MINERALOGY AND PHENOMENON OF CLAY SWELLING IN OIL & GAS INDUSTRY
PublicationAmong the minerals found in the earth's crust, clay minerals are of the widest interest. Due to the specific properties such as plasticity, absorbing and catalytic properties clay minerals are used in many industries (oil & gas, chemistry, pharmacy, refractory technology, ceramics etc.). In drilling, a phenomenon of swelling clays is frequently observed. It has an important impact on the cementing quality. During the last few decades...
-
Ocena stanu powierzchni kulek ceramicznych po nagniataniu tocznym stali hartowanej Cf53
PublicationW artykule przedstawiono wyniki z badań eksperymentalnych dotyczących przydatności kulek wykonanych z ceramiki technicznej, do nagniatania tocznego, narzędziami z dociskiem hydrostatycznym. W badaniach wykorzystano narzędzie umożliwiające wymianę kulek nagniatających. Badania wykonano poprzez nagniatanie wałków wykonanych ze stali Cf53 w stanie utwardzonym (zahartowanym). Wyniki badań obejmują charakterystyki stanu powierzchni...
-
Results of abrasive slurry dosage in lapping process
PublicationPrzedstawiono wyniki badań dawkowania zawiesiny ściernej w docieraniu powierzchni płaskich elementów ceramicznych. Analizowano wpływ dawkowania na podstawowe parametry chropowatości powierzchni ceramiki Al2O3 i Al2O3-ZrO2.
-
In Vitro Dissolution of Na-Ca-P-Oxynitrides
Publication: Sodium-calcium-phosphate based oxynitride glasses and glass-ceramics doped with Mg, Si, and Nb were studied in vitro in simulated body fluid (SBF) under static conditions. The release of ions and pH changes up to 7 days of immersion were investigated. The nitrogen incorporation into phosphate glass matrix was found to notably influence in vitro dissolution only of homogenous glasses. Increasing the nitrogen content in the samples...
-
Novel Low-Loss Substrates for 5G Applications
PublicationThis paper presents a feasibility study of a new type of microwave low-loss dielectric substrates for 5G network applications. The new substrate materials are composites of polypropylene and high-dielectric-constant micro-ceramics. This combination is expected to form a very low-loss dielectric material at low fabrication cost. Two substrate samples with different dielectric properties are fabricated and their characteristics at...
-
Allergic reactions as a defense of the organism to the influence of implants components made of stainless steel
PublicationDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
-
Development of polyurethanes for bone repair
PublicationThe purpose of this paper is to review recent developments on polyurethanes aimed at the design, synthesis, modifications, and biological properties in the field of bone tissue engineering. Different polyurethane systems are presented and discussed in terms of biodegradation, biocompatibility and bioactivity. A comprehensive discussion is provided of the influence of hard to soft segments ratio, catalysts, stiffness and hydrophilicity...
-
Allergic Reactions as a Defense of the Organism to the Influence of Implants Components Made of Stainless Steel
PublicationDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
-
ZUŻYCIE POWIERZCHNI KULEK CERAMICZNYCH W PROCESIE NAGNIATANIA TOCZNEGO STALI HARTOWANEJ
PublicationPrzedstawiono wyniki z badań eksperymentalnych dotyczących przydatności kulek wykonanych z ceramiki technicznej, do nagniatania tocznego, narzędziami z dociskiem hydrostatycznym. W przeprowadzonych badaniach zastosowano narzędzie umożliwiające wymianę kulek ceramicznych zastosowanych jako elementów nagniatające. Badania wykonano poprzez nagniatanie próbek - wałków wykonanych ze stali Cf53 w stanie utwardzonym (zahartowanym). Wyniki...
-
Electrocatalytic Gas Sensor with Reference Layer
PublicationThis paper presents studies of gas sensors prepared in ceramic technology with Nasicon as a solid electrolyte. Sensors work in the voltammetric mode thus based on the excitation of a sensor with a periodic potential signal while current response is recorded. The main aim is to investigate a Bi8Nb2O17 reference layer influence on sensor properties. Sensors I-V characteristics in different concentration of nitrogen dioxide have been...
-
Vertical vibration reduction and audible sound analysis in surface grinding with electroplated tools
PublicationOne of the first approaches to the development of a grinding process monitoring system based on audible sound sensors is presented in the paper. Electroplated diamond tools (abrasive D64 and D107) were used in a modified single-disc lapping machine configuration for flat grinding of ceramics (Al2O3). The main aim of the machine modification was to reduce the vertical vibration in order to decrease the tool wear and to increase...
-
Wpływ dawkowania zawiesiny ściernej na efekty docierania powierzchni płaskich
PublicationPrzedstawiono wyniki badań dawkowania zawiesiny ściernej podczas docierania powierzchni płaskich. Określono wpływ wielkości dawki ścierniwa na wydajność obróbki i podstawowe parametry chropowatości powierzchni. Obrabiano elementy z ceramiki tlenkowej oraz miedziane.
-
Analiza czasochłonności docierania jednotarczowego powierzchni płaskich elementów ceramicznych - studium przypadku
PublicationPrzedstawiono analizę czasochłonności docierania elementów ceramicznych. Badano czasochłonność obróbki na dwóch docierarkach jednotarczowych o znacząco różniących się średnicach tarcz docierających. Porównano czasy jednostkowe docierania elementów płaskich z ceramiki technicznej Al2O3
-
Characteristics of La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 3-δ -supported micro-tubular solid oxide fuel cells with LaCo 0.4 Ni 0.6-x Cu x O 3-δ cathodes
PublicationIn this study, micro-tubular solid oxide fuel cells (T-SOFCs) with extruded La0.8Sr0.2Ga0.8Mg0.2O3-δ (LSGM) electrolyte as the mechanical support and LaCo0.4Ni0.6O3-δ (LCNO) or LaCo0.4Ni0.4Cu0.2O3-δ (LCNCO) as cathodes were prepared and characterized. Partial substitution of Cu for the Ni-ion positions in the LCNO lattices was found to significantly enhance the densification and accelerate the grain growth. The porosity-corrected...
-
Injectable bone cement based on magnesium potassium phosphate and cross-linked alginate hydrogel designed for minimally invasive orthopedic procedures
PublicationBone cement based on magnesium phosphate has extremely favorable properties for its application as a bioactive bone substitute. However, further improvement is still expected due to difficult injectability and high brittleness. This paper reported the preparation of novel biocomposite cement, classified as dual-setting, obtained through ceramic hydration reaction and polymer cross-linking. Cement was composed of magnesium potassium...
-
Analiza czasochłonności docierania technologicznego powierzchni płaskich w operacjach montażowych.
PublicationPrzedstawiono wyniki analiz docierania i mikroszlifowania elementów płaskich na docierarce jednotarczowej mikroziarnami węglika krzemu. Obrabiano elementy ze stali 100Cr oraz z tlenkowej ceramiki technicznej Al2O3. Analizowano czas obróbki i koszty operacji.
-
Correlation between structural and electrical properties in highly porous (Y,Sr)(Ti,Nb)O3-delta SOFC anodes
PublicationIn order to find a relationship between structural and electrical properties, niobium and yttrium doped SrTiO3 ceramics were prepared via solid-state reaction. The samples were sintered in hydrogen and air conditions. The samples were also fabricated with a pore-former to obtain highly porous specimens. The electrical properties of Nb-doped SrTiO3 samples and yttrium and niobium co-doped SrTiO3 were compared. The comparable electrical...
-
Forming Ni-Fe and Co-Fe Bimetallic Structures on SrTiO3-Based SOFC Anode Candidates
PublicationThe aim of this work was to verify the possibility of forming Ni-Fe and Co-Fe alloys via topotactic ion exchange exsolution in Fe-infiltrated (La,Sr,Ce)0.9(Ni,Ti)O3-δ or (La,Sr,Ce)0.9(Co,Ti)O3-δ ceramics. For this purpose, samples were synthesized using the Pechini method and then infiltrated with an iron nitrate solution. The reduction process in dry H2 forced the topotactic ion exchange exsolution, leading to the formation of...
-
Udział nośny powierzchni elementów ceramicznych i węglików spiekanych po docieraniu.
PublicationPrzedstawiono wyniki badań docierania jednotarczowego powierzchni elementów z ceramiki technicznej i węglików spiekanych. Analizowano jakość obróbki i udział nośny powierzchni po docieraniu. Docieranie powierzchni płaskich jest technologią pozwalającą uzyskać duży udział nośny.
-
Ocena czynnej powierzchni narzędzia w mikroszlifowaniu powierzchni płaskich z kinematyką docierania jednotarczowego
PublicationPrzedstawiono wyniki badań eksperymentalnych mikroszlifowania z kinematyką docierania w układzie jednotarczowym. Badania miały na celu wyznaczenie okresu trwałości narzędzia i zmieniających się w czasie jego właściwości ściernych. Badania przeprowadzono na próbkach z ceramiki aluminiowej.
-
Wpływ zawiesiny ściernej dawkowanej w sposób wymuszony na wydajność docierania jednotarczowego elementów ceramicznych
PublicationPrzedstawiono zagadnienia związane z przygotowywaniem zawiesiny ściernej w docieraniu maszynowym powierzchni płaskich. W badaniach zastosowano wymuszony sposób dozowania zawiesiny na docierak żeliwny. Badano docieranie elementów z ceramiki tlenkowej zawiesiną na bazie mikroziaren węglika krzemu.
-
Coatings in arthroplasty [online]
PublicationThe modern coatings used in arthroplasty for long term implants are reviewed. The phosphate coatingsare the most popular technique to improve the bone-implant interfacial strength and promote theosseointegration. The plasma spraying, electrophoretic precipitation, powder metallurgy, ion beamsputtering, high velocity oxy-fuel (HVOF) combustion spraying, sol-gel technique, biomimeticdeposition are mostly used to obtain the phosphate,...
-
KTaO3 a perovskite for water and air treatment
PublicationPerovskites are inorganic compounds that exhibit dielectric properties. These minerals belong to the crystal ceramics family. These compounds are described by the formula: ABX3 where, A and B are 2, 3 or 4 valuable metal ions, and X is an ion of oxygen or fluorine. An example of perovskite is the compound KTaO3. There are many methods for producing KTaO3, but the hydrothermal method is most commonly used. Perovskites can be characterized...
-
Water uptake kinetics and electrical transport in BaCe0.6Zr0.2Y0.1M0.1O3−δ (M = Tb, Pr, Fe) protonic conductors
PublicationBaCe0.6Zr0.2Y0.1M0.1O3−d (M = Fe, Pr, Tb) is a mixed conducting oxide in which three mobile charge carriers – oxygen ion, electron/hole, and protonic defects – are present. These types of materials have gained much interest as electrode materials for protonic ceramic fuel cells (PCFCs) and protonic ceramic electrolysis cells (PCECs). In this study, the water uptake and oxygen transport properties of different BaCe0.6Zr0.2Y0.1M0.1O3−d...
-
Analiza gniazda docierarek dwutarczowych do płaszczyzn - studium przypadku.
PublicationPrzedstawiono analizę gniazda trzech docierarek dwutarczowych do płaszczyzn. Analizowano przypadki obróbki pierścieni stalowych i krążków z ceramiki technicznej. Badano czasy główne docierania oraz składowe czasów pomocniczych w analizowanych operacjach obróbki wstępnej, dokładnej i bardzo dokładnej.
-
Problematyka mycia elementów obrabianych po operacjach docierania jednotarczowego powierzchni płaskich
PublicationW artykule omówiono wybrane zagadnienia mycia elementów po wykończeniowej obróbce ściernej luźnym ścierniwem. Przedstawiono technikę pooperacyjnego mycia ultradźwiękowego, czasochłonność oczyszczania drobnych elementów z ceramiki technicznej oraz skuteczność mycia ręcznego i ultradźwiękowego żeliwa sferoidalnego po docieraniu.
-
Oxygen deficient YBa2Cu3O7-r: two superconducting phases
PublicationZestaw próbek ceramiki YBa2Cu3O7-r w postaci pudru i granulatupoddawano stopniowemu odtlenianiu i badano za pomocątermograwimetrii oraz absorbcji mikrofalowej. Stosowanie tychmetod pokazało, że występująca faza $Trm_c=60$~K w związkuYBa2Cu3O7-r, powstała poprzez odtlenianie jest niestabilna.
-
Recent advances on spinel-based protective coatings for solid oxide cell metallic interconnects produced by electrophoretic deposition
PublicationThe application of ceramic protective coatings to the metallic interconnects in solid oxide cells (SOCs) is a viable and effective method to limit interconnect degradation issues. This featured letter provides a critical overview of the main outcomes of current research on the use of the electrophoretic deposition (EPD) technique to produce protective coatings for SOC metallic interconnects, specifically focusing on different approaches...
-
Material Design and Optimisation of Electrochemical Li-Ion Storage Properties of Ternary Silicon Oxycarbide/Graphite/Tin Nanocomposites
PublicationIn this work, we present the characterization and electrochemical performance of various ternary silicon oxycarbide/graphite/tin (SiOC/C/Sn) nanocomposites as anodes for lithium-ion batteries. In binary SiOC/Sn composites, tin nanoparticles may be produced in situ via carbothermal reduction of SnO2 to metallic Sn, which consumes free carbon from the SiOC ceramic phase, thereby limiting the carbon content in the final ceramic nanocomposite....
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublicationThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
Fabrication of solid oxide fuel cell supported on speciallyperformed ferrite-based perovskite cathode
PublicationW pracy przedstawiono warunki technologiczne niezbedne do wytworzenia tlenkowego ogniwa paliwowego na elencie nośnym z materiału perowskitowego LSF. Jako elektrolit stosowana była ceramika z tlenku ceru. Między innymi badany były właściwości elektryczne zarówno materiału katodowego jak i ogniwa.
-
Optical monitoring of thin oil film thickness in extrusion processes
PublicationPraca porusza problem pomiaru grubości cienkiej warstwy przyściennej -oleju, podczas procesu wyciskania ceramiki modelowej. Szczegółowo opisuje zjawiska fizyczne zachodzące w warstwie przyściennej oraz dynamiczne parametry wykorzystywane do oceny grubości. Autorzy opisują także metodę pomiaru oraz konstrukcję układów pomiarowych.