Search results for: AMPHIPHILIC COPOLYMERS
-
MXene-based composites for capacitive deionization – The advantages, progress, and their role in desalination - A review
PublicationMXenes, a novel large family of 2D transition metal carbides, carbonitrides and nitrides are currently a “hot topic” in science due to their several fascinating physical and chemical properties. It follows from a rich diversity of their elemental compositions and chemical functionalities. MXenes can form composites with many substances, including polymers or metal oxides, which allows to effective “tune” MXene characteristics to...
-
Polyether-block-amide PEBA membranes for gas separation and pervaporation; current design and applications
PublicationPolyether-block-amide (PEBA) membranes have attracted considerable attention for their exceptional efficacy in gas separation and pervaporation processes. This comprehensive review delves into the precise definition, distinguishing characteristics, and diverse applications of PEBA membranes over the past five years. A primary research objective focuses on enhancing gas separation efficiency, primarily through augmenting membrane...
-
Clays as Inhibitors of Polyurethane Foams’ Flammability
PublicationPolyurethanes are a very important group of polymers with an extensive range of applications in different branches of industry. In the form of foams, they are mainly used in bedding, furniture, building, construction, and automotive sectors. Due to human safety reasons, these applications require an appropriate level of flame retardance, often required by various law regulations. Nevertheless, without the proper modifications,...
-
Tensile validation tests with failure criteria comparison for various GFRP laminates
PublicationThe paper studies the mechanical properties of glass fibre reinforced polymers (GFRP) with various types and orientation of reinforcement. Analyzed specimens manufactured in the infusion process are made of polymer vinyl ester resin reinforced with glass fibres. Several samples were examined containing different plies and various fibres orientation [0, 90] or [+45, –45]. To assess the mechanical parameters of laminates, a series...
-
Liquefaction of alder wood as the source of renewable and sustainable polyols for preparation of polyurethane resins
PublicationLiquefaction of wood-based biomass gives different polyol properties depending on the reagents used. In this article, alder wood sawdust was liquefied with glycerol and poly(ethylene glycol) solvents. Liquefaction reactions were carried out at temperatures of 120, 150 and 170 °C. The obtained bio-polyols were analyzed in order to establish the process efficiency, hydroxyl number, acid value, viscosity and structural characteristics...
-
Noise and Electro-Ultrasonic Spectroscopy of Conducting PolymerThick Films
PublicationThick conducting films based on conducting polymer are characterized by DC conductivity and noise in temperature range 10 to 300 K. Conducting polymers could be used e.g. for the top electrode (cathode) in the solid tantalum or niobium capacitors. On the conducting polymer layer the top layer of carbon/graphite and/or silver polymer based pastes is applied in the capacitor technology. Our samples structure consists of conducting...
-
Structure and properties of the exopolysaccharides produced by Pseudomonas mutabilis T6 and P. mutabilis ATCC 31014
PublicationThis paper presents a study on the purification, primary structure, and rheological properties of exopolysaccharides isolated from cultures of Pseudomonas mutabilis T6 and P. mutabilis ATCC 31014. Both polymers are exopolysaccharides of D-mannose. The mannan isolated from P. mutabilis T6 contains on average about 5% of residual b-D-glucose, in contrast to the mannan from P. mutabilis ATCC 31014, which contained only trace amounts...
-
Waterborne polyesters partially based on renewable resources
PublicationA new experimental approach for preparing biobased, water-soluble polyesters via titanium(IV) n-butoxide-catalyzed bulk polycondensation is presented. In the described method polymers were obtained from isosorbide, maleic anhydride and poly(ethylene glycol). The chemical structure of the synthesized polyesters was confirmed using 2D NMR spectroscopy and by titration methods. Careful analysis of 2D NMR spectra viz. Correlation Spectra...
-
Comparative Analysis of Carbon, Ecological, and Water Footprints of Polypropylene-Based Composites Filled with Cotton, Jute and Kenaf Fibers
PublicationComposites containing natural fibers are considered environmentally friendly materials which is related to the reduced use of fossil fuels and the emission of carbon dioxide compared to petroleum-based polymers. Nevertheless, a complete evaluation of their environmental impact requires a broader view. This paper presents a carbon, ecological, and water footprints assessment of polypropylene-based composites filled with cotton,...
-
Potential applications of by-products from the coffee industry in polymer technology – Current state and perspectives
PublicationCoffee is one of the most popular beverages in the world, and its popularity is continuously growing, which can be expressed by almost doubling production over the last three decades. Cultivation, processing, roasting, and brewing coffee are known for many years. These processes generate significant amounts of by-products since coffee bean stands for around 50% of the coffee cherry. Therefore, considering the current pro-ecological...
-
Synthesis and Characterization of Poly(zwitterionic) Structures for Energy Conversion and Storage
PublicationZwitterions are unique class of molecules that possess two functional groups bearing electric charges, one positive and second negative. This setup results in peculiar properties such as high water retention and anti-fouling capability. Therefore, zwitterionic coatings and gels are commonly applied in e.g. biosensing and bioelectronic devices. Despite those applications, there are other perspectives for zwitterionic materials....
-
Effect of Ion and Binding Site on the Conformation of Chosen Glycosaminoglycans at the Albumin Surface
PublicationAlbumin is one of the major components of synovial fluid. Due to its negative surface charge, it plays an essential role in many physiological processes, including the ability to form molecular complexes. In addition, glycosaminoglycans such as hyaluronic acid and chondroitin sulfate are crucial components of synovial fluid involved in the boundary lubrication regime. This study presents the influence of Na+, Mg2+ and Ca2+ ions...
-
Impact and stretching standardized tests as useful tools for assessment of viscoelastic behavior for highly rubberized asphalt binder
PublicationAsphalt binder is generally identified as a brittle material at low service temperature or under high-speed load, and the brittleness becomes serious after weathering aging. Improving the toughness of asphalt binder through adding high-content of crumb tire rubber is an efficient method to solve this problem. Devulcanized rubber modified asphalt binder (DRMA) with different contents (15–40%) of devulcanized rubber (DR) were prepared...
-
Shape Memory Polyurethane Materials Containing Ferromagnetic Iron Oxide and Graphene Nanoplatelets
PublicationIntelligent materials, such as memory shape polymers, have attracted considerable attention due to wide range of possible applications. Currently, intensive research is underway, in matters of obtaining memory shape materials that can be actuated via inductive methods, for example with help of magnetic field. In this work, an attempt was made to develop a new polymer composite—polyurethane modified with graphene nanoplates and...
-
Introduction to MIP synthesis, characteristics and analytical application
PublicationOne of the trends in analytical chemistry is associated with designing and developing new types of sample preparation techniques, which might significantly increase the efficiency and selectivity of the analytes isolation or/and preconcentration process. One of the most widely employed solutions are selective sorption materials, defined as molecularly imprinted polymers (MIPs), as well as the sorbents with the molecular fingerprint....
-
Implementing fermentation technology for comprehensive valorisation of seafood processing by-products: A critical review on recovering valuable nutrients and enhancing utilisation
PublicationFermentation technology is a biorefining tool that has been used in various industrial processes to recover valuable nutrients from different side streams. One promising application of this technique is in the reclamation of nutritional components from seafood side streams. Seafood processing generates significant amounts of waste, including heads, shells, and other side streams. These side streams contain high quantities of valued...
-
The influence of chemical composition of amide block on the thermal properties and structure of terpoly(ester-b-ether-b-amide) elastomers
PublicationMultiblock terpolymers-(PBT-b-PTMO-b-PA12,10)(n)- constituting the polymer systems, in which one of the three blocks (PBT) does not dissolve in PA12,10 block (hard phase) and, depending on its molecular weight is slightly soluble in PTMO block (soft phase), have been obtained. The DSC method was applied to investigate the thermal properties of these polymers and it was found that PBT block acts as an element that produces stiffness...
-
Thermal and Mechanical Behavior of Elastomers Incorporated with Thermoregulating Microcapsules
PublicationPolyurethane (PU) is one of the principal polymers in the global plastic market thanks to its versatility and continuous improvement. In this work, PU elastomeric materials having thermoregulating properties through the incorporation of microcapsules (mSD-(LDPE·EVA-RT27)) from low-density polyethylene and vinyl acetate containing paraffin®RT27 as PCM were produced. Elastomers were synthesized while varying the molar ratio [NCO]/[OH]...
-
Shape memory thin films of Polyurethane: Does graphene content affect the recovery behavior of Polyurethane nanocomposites?
PublicationThin nanocomposite films of polyurethane have received remarkable attention due to their shape memory properties. As most of the reports focus on the beneficial aspects of the presence of nanofillers such as graphene nanoplatelets (GNPs) introduced into shape memory polymers, some research results reveal the opposite trend. The polyether/polyester-based polyurethane was synthesized through a condensation polymerization and the...
-
Investigation of poly(3,4-ethylenedioxythiophene) deposition method influence on properties of ion-selective electrodes based on bis(benzo-15-crown-5) derivatives
PublicationGlassy carbon electrodes modified by conductive polymers and membrane with derivatives of bis(benzo-15-crown-5) were tested as solid contact ion selective electrodes for K+ ions concentration determination. PEDOT with PSS, Cl- and ClO4- counter ions was electrochemically deposited onto glassy carbon substrates using four different electrochemical approaches (potentiostatic, galvanostatic, potentiodynamic and potentiostatic pulses)....
-
Salt melt synthesis of curved nitrogen-doped carbon nanostructures: ORR kinetics boost
PublicationImplementing metal-free electrocatalysts for the oxygen reduction reaction (ORR) and revealing crucial chemical or topographical parameters driving their activity are vital for the development of power cells. The carbon-based catalysts are very often synthesized through carbonization of biopolymers, in particular, those one containing nitrogen groups such as chitosan. Unfortunately, the resulting carbonaceous materials usually...
-
Green engineered biomaterials for bone repair and regeneration: Printing technologies and fracture analysis
PublicationDespite the exceptional self-regeneration properties of bone, severe injuries often require additional surgical intervention such as using artificial bone constructs. These structures need to meet a number of criteria regarding their structure, performance, alongside the rate and the mechanism of erosion and fracture when implanted, for stimulating the regeneration of defected bone and, more critically providing support in the...
-
Chemical Characteristics and Thermal Oxidative Stability of Novel Cold-Pressed Oil Blends: GC, LF NMR, and DSC Studies
PublicationPlant oils contain a high content of unsaturated fatty acids. Studies of food products have revealed a considerable disproportion in the ratio of ω6 to ω3. This article presents information on the healthful qualities of eight new oil blends that contain a beneficial proportion of ω6 to ω3 fatty acids (5:1), as well as their degradation during heating at 170 and 200 °C. The fatty acid profile was analyzed by gas chromatography (GC),...
-
The Reactivity of Phosphanylphosphinidene Complexes of Transition Metals Toward Terminal Dihaloalkanes
PublicationThe reactivities of phosphanylphosphinidene complexes [(DippN)2W(Cl)(η2-P−PtBu2)]− (1), [(pTol3P)2Pt(η2- P=PtBu2)] (2), and [(dppe)Pt(η2-P=PtBu2)] (3) toward dihaloalkanes and methyl iodide were investigated. The reactions of the anionic tungsten complex (1) with stochiometric Br(CH2)nBr (n = 3, 4, 6) led to the formation of neutral complexes with a tBu2PP(CH2)3Br ligand or neutral dinuclear complexes with unusual tetradentate...
-
Tailoring of SiOC composition as a way to better performing anodes for Li-ion batteries
PublicationPolymer derived silicon oxycarbide (SiOC) ceramics are investigated as potential anodes for lithiumion batteries. Different SiOC ceramics are prepared by pyrolysis (1000 °C and 1400 °C under controlled argon atmosphere) of polysiloxanes ceramic precursors. Preceramic polymers are synthesized using the sol–gel method. Phenyltriethoxysilane (PhTES) and methyltriethoxysilane (MTES) have been used as starting precursors and mixed with...
-
THE ANALYSIS OF THE INFLUENCE OF STRESS DISTRIBUTION ON WEAR PROFILE IN LUBRICATED SLIDING CONTACT OF UHMW-PE VS TITANIUM Ti-13Nb-13Zr ALLOY
PublicationMetal – polymer sliding contacts are a typical combination in industry and medicine. For decades such a set of materials has been the primary choice in human joints endoprosthetic technology. In this paper tribological issues of are presented from a research on the potential for practical use of Ti-13Nb-13Zr/UHMW-PE couple for orthopedic endoprosthesis. In tests on simplified models it is critically important to carefully...
-
Comparative analysis of the flow control over a circular cylinder with detached flexible and rigid splitter plates
PublicationA comparative study is performed on a circular cylinder with both flexible and rigid splitter plates (SPs). This study has the novelty of using single and dual detached SPs located downstream of the cylinder. The dimensionless gap distance between the first splitter plate and the cylinder as well as the distance between the SPs are varied. The strain of flexible SPs can be used for energy harvesting from the flow. Therefore, a...
-
Thermal degradation of polylactic acid (PLA)/polyhydroxybutyrate (PHB) blends: A systematic review
PublicationPolylactic acid (PLA) and polyhydroxybutyrate (PHB) are two biopolyesters obtained from renewable resources like corn or sugar under bacterial fermentation. PLA is the most widely used biopolymer in diverse applications. Addition of PHB to PLA can improves the crystallinity of PLA, and thereby its mechanical strength. However, both PLA and PHB suffer from poor thermal stability, which limits their potential industrial application....
-
Mater-Bi/Brewers’ Spent Grain Biocomposites—Novel Approach to Plant-Based Waste Filler Treatment by Highly Efficient Thermomechanical and Chemical Methods
PublicationThermoplastic starch (TPS) is a homogenous material prepared from native starch and water or other plasticizers subjected to mixing at a temperature exceeding starch gelatinization temperature. It shows major drawbacks like high moisture sensitivity, poor mechanical properties, and thermal stability. To overcome these drawbacks without significant cost increase, TPS could be blended with bio-based or biodegradable polymers and...
-
The Influence of Drying Temperature on Color Change of Hornbeam and Maple Wood Used as Surface and Inner Layers of Wood Composites
PublicationThe thermal treatment of wood changes its structure due to the degradation of wood polymers (cellulose, hemicellulose and lignin), so the physical properties of wood are either improved or degraded. Color changes apply not only to natural wood, but also to such wood composites for which some amount of glue is used in their construction (e.g., plywood, blockboard or laminboard). This article is focused on the analysis of hornbeam...
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 1/2
PublicationWind power plants are considered as ecologically-clean source of energy. However, manufacturing processes cannot be treated that way. Manufacturing processes consume huge amount of electrical and thermal energy and significant amount of materials, e.g. steel, polymers, oils and lubricants. All of the above could be potentially harmful for environment. There are not many works and publications regarding life-cycle analysis of wind...
-
Mechanical Properties, Microstructure and Surface Quality of Polypropylene Green Composites as a Function of Sunflower Husk Waste Filler Particle Size and Content
PublicationAgricultural waste is a still untapped source of materials that can, in case of proper utilization, significantly improve the sustainability of polymers and their composites. In this work, polymer composites based on isotactic polypropylene were produced incorporating ground sunflower husk in the amount of 10 wt% and 20 wt%. The work’s main objective is to evaluate how preliminary fractioning of this agricultural waste filler affects...
-
Experimental study on the effect of selected sterilization methods on mechanical properties of polylactide FFF specimens
PublicationPurpose: Biodegradable polymers are widely used in personalized medical devices or scaffolds for tissue engineering. The manufacturing process should be finished with sterilization procedure. However, it is not clear how the different sterilization methods have an impact on the mechanical strength of the three-dimensional (3D)-printed parts, such as bone models or personalized mechanical devices. This paper aims to present the...
-
Fully Isohexide-Based Polyesters: Synthesis, Characterization, and Structure-Properties Relations
PublicationHere we present a novel series of biobasedpolyesters solely based on renewable isohexide building blocks,synthesized via melt polymerization. The recently developedisoidide dicarboxylic acid (IIDCA) was polymerized with rigidrenewable diols such as isosorbide (IS), isomannide (IM),isoidide (II), and the novel 2,5-methylene-extended isoididedimethanol (IIDML). Both IIDCA and IIDML weredeveloped to increase the reactivity of the...
-
Toughness augmentation by fibrillation and yielding in nanostructured blends with recycled polyurethane as a modifier
PublicationIn the present paper, we have carefully investigated the morphology and fracture mechanism of the recycled polyurethane (RPU) /epoxy blend system. The second phase (RPU) added to the epoxy resin has a positive effect on the overall mechanical properties. Interestingly, the recycled polymer has a remarkable effect on the fracture toughness of epoxy resin. The mechanism behind the fracture toughness improvement up on the addition...
-
Abual Hassan Mr.
PeopleI have completed my B.Sc in Industrial and Manufacturing Engineering in 2017 from the University of Engineering and Technology in Lahore, Pakistan. In 2017 Chinese Govt Offered me a Fully funded scholarship and completed my MEng in Mechanical Engineering from Northwestern Polytechnical University Xi'an, China. There I graduated with the honor of Excellent Post-Graduate Student of the Year 2020. My research interests include Additive...
-
Polysaccharide nanocomposites in wastewater treatment: A review
PublicationIn modern times, wastewater treatment is vital due to increased water contamination arising from pollutants such as nutrients, pathogens, heavy metals, and pharmaceutical residues. Polysaccharides (PSAs) are natural, renewable, and non-toxic biopolymers used in wastewater treatment in the field of gas separation, liquid filtration, adsorption processes, pervaporation, and proton exchange membranes. Since addition of nanoparticles...
-
Recycling of Industrial Waste as Soil Binding Additives—Effects on Soil Mechanical and Hydraulic Properties during Its Stabilisation before Road Construction
PublicationTo improve the in situ soil stabilization, different chemical additives are used (ion exchange compounds, additives based on H2SO4 or vinyl polymers, and organic additives using lignosul- fonates). One interesting alternative is the production of additives from various waste materials. The extensive testing of waste-based blends with soil was performed; the mechanical (unconfined compressive strength (UCS)) and hydraulic (capillary...
-
Emissions of selected monoaromatic hydrocarbons as a factor affecting the removal of single-use polymer barbecue and kitchen utensils from everyday use
PublicationThe main focus of this study is the emission of monoaromatic hydrocarbons because these are the preliminary factors of potential solvent and monomer residues present in single-use plastic barbecue and kitchen utensils comprising polystyrene, polypropylene, natural cellulose, and biodegradable polymers intended for use with hot meal or beverages. Herein, the emissions of monoaromatic hydrocarbons (styrene, benzene, toluene, ethylbenzene,...
-
Time-frequency analysis in optical coherence tomography for technical objects examination
PublicationOptical coherence tomography (OCT) is one of the most advanced optical measurement techniques for complex structure visualization. The advantages of OCT have been used for surface and subsurface defect detection in composite materials, polymers, ceramics, non-metallic protective coatings, and many more. Our research activity has been focused on timefrequency spectroscopic analysis in OCT. It is based on time resolved spectral analysis...
-
Processing of Biomass Prior to Hydrogen Fermentation and Post-Fermentative Broth Management
PublicationUsing bioconversion and simultaneous value-added product generation requires purifica- tion of the gaseous and the liquid streams before, during, and after the bioconversion process. The effect of diversified process parameters on the efficiency of biohydrogen generation via biological pro- cesses is a broad object of research. Biomass-based raw materials are often applied in investigations regarding biohydrogen generation using...
-
Non-Isocyanate-Based Waterborne Polyurethanes
PublicationNon-isocyanate polyurethanes (NIPUs) are a greener alternative for the conventional polyurethanes synthesized using toxic and moisture-sensitive di- or polyisocyanates. The most often described method of NIPU synthesis involves the reaction of five-membered cyclic carbonates with amines, and resulting polymers containing primary and secondary hydroxyl groups (so they are also known as polyhydroxyurethanes), which can be further...
-
Electrically Conductive Carbon‐based (Bio)‐nanomaterials for Cardiac Tissue Engineering
PublicationA proper self-regenerating capability is lacking in human cardiac tissue which along with the alarming rate of deaths associated with cardiovascular disorders makes tissue engineering critical. Novel approaches are now being investigated in order to speedily overcome the challenges in this path. Tissue engineering has been revolutionized by the advent of nanomaterials, and later by the application of carbon-based nanomaterials...
-
Real-time monitoring of volatiles and particles emitted from thermoplastic filaments during 3D printing
PublicationThe proliferation of consumer-grade three-dimensional (3D) printers using fused deposition, also known as fused filament fabrication, has given rise to concerns over the exposure of users to potentially harmful substances. Thermoplastic filaments made of different polymers are extruded through a heated printer nozzle and deposited layer by layer on a build platform to form the printed object. This process leads to the emission...
-
Fabrication methods of smart composite coatings - review
PublicationPostoperative bacterial infections are one of the main reasons for unsuccessful implantation of long-term implants. The development of bacterial infection requires antibiotic therapy, in extreme cases a reimplantation procedure is necessary. In order to provide materials for implants with antibacterial properties, they are subjected to modifications to create a coating that will release the drug substance, when the inflammation...
-
Structural, mechanical and thermal behavior assessments of PCL/PHB blends reactively compatibilized with organic peroxides
PublicationThe efficiency of two commercially available organic peroxides, dicumyl peroxide (DCP) and di-(2-tert-butyl-peroxyisopropyl)-benzene (BIB), during reactive processing of poly (ε-caprolactone)/poly (3-hydroxybutyrate) (PCL/PHB) blends was investigated. The changes in chemical structure of PCL/PHB blends, as a function of organic peroxide type (DCP/BIB) and content (in range: 0–1.0 parts by weight - pbw), were characterized by Fourier...
-
Advanced polarization sensitive analysis in optical coherence tomography
PublicationThe optical coherence tomography (OCT) is an optical imaging method, which is widely applied in variety applications. This technology is used to cross-sectional or surface imaging with high resolution in non-contact and non-destructive way. OCT is very useful in medical applications like ophthalmology, dermatology or dentistry, as well as beyond biomedical fields like stress mapping in polymers or protective coatings defects detection....
-
Recycled rubber wastes-based polymer composites with flame retardancy and electrical conductivity: Rational design, modeling and optimization
PublicationPolymer recycling techniques experience a maturity period of design and application. Rubbers comprise a high proportion of polymer wastes, highly flammable and impossible to re-melt. Polymer composites based on ground tire rubber (GTR) and ethylene-vinyl acetate copolymer (EVA) containing carbon black (CB) (1–50 phr), with variable EVA/GTR weight composition (10/90, 25/75, 50/50, 75/25 and 90/10), and processing temperature (Low:...
-
Rubber wastes recycling for developing advanced polymer composites: A warm handshake with sustainability
PublicationRecycling and management of rubber wastes experiences an early-stage maturity in the quest for sustainable and circular materials. Up to now, solutions proposed for sustainable development of rubber wastes are limited, so that properties and performance features of recycled products are inadequate for practical applications. Herein, an experimental protocol is introduced for manufacturing semi-sustainable polymer composites based...
-
More than just a beer – Brewers' spent grain, spent hops, and spent yeast as potential functional fillers for polymer composites
PublicationBeer is among the most popular beverages in the world, with the production distributed uniformly between the biggest continents, so the utilization of brewing by-products is essential on a global scale. Among their potential recipients, the plastics industry offers extensive range of potential products. Herein, the presented study investigated the application of currently underutilized solid brewing by-products (brewers' spent...