Filters
total: 893
-
Catalog
Search results for: SICN CERAMIC
-
Fabrication of wormhole-like YSZ and Ni-YSZ by the novel soft-hard template CTAB/NaCl-assisted route. Suppressing Ni coalescence in SOFC
PublicationA novel one-pot synthesis route leading to the formation of a wormhole-like structure was developed for the successful fabrication of porous YSZ and Ni-YSZ systems. This method involved co-precipitation in the presence of the micelle-forming agents CTAB/Pluronic P123 and crystallising NaCl. The obtained skeletons were mechanically stable and presented almost 50% uniform, open porosity without using any additional pore-formers....
-
Electrophoretic co-deposition of Fe2O3 and Mn1,5Co1,5O4: Processing and oxidation performance of Fe-doped Mn-Co coatings for solid oxide cell interconnects
PublicationThe “in-situ” Fe-doping of the manganese cobalt spinel was achieved by electrophoretic co-deposition of Mn1,5Co1,5O4 and Fe2O3 powders followed by a two-step reactive sintering treatment. The effects on the coating properties of two different Fe-doping levels (5 and 10 wt.% respectively) and two different temperatures of the reducing treatment (900 and 1000 °C) are discussed. Samples with Fe-doped coatings demonstrated a lower...
-
Processing of Ce0.8Gd0.2O2-δ barrier layers for solid oxide cells: The effect of preparation method and thickness on the interdiffusion and electrochemical performance
PublicationCe0.8Gd0.2O1.9 (CGO) barrier layers are required to mitigate the chemical reactions between Sr-containing oxygen electrode materials and Zr-based oxygen ion conductors in high-temperature solid oxide cells. Barrier layers produced by different methods were studied in this work. As a reference, a cell with no barrier layer was measured. The application of the powder-processed barrier layers, considerably increases the performance....
-
Low temperature deposition of dense MnCo 2 O 4 protective coatings for steel interconnects of solid oxide cells
PublicationIn this work manganese cobalt spinel (MnCo2O4) coatings were deposited on steel substrates by spray pyrolysis at 390 °C. This is at much lower temperatures than previously reported (typically in excess of 900 °C). It was possible to produce coatings with well controlled thickness (2-5-10 μm). The as-deposited coatings were evaluated for their microstructural changes and electrical conductivity up to 800 °C. Results confirm the...
-
Antimony substituted lanthanum orthoniobate proton conductor – structure and electronic properties.
PublicationX‐ray and neutron diffraction have been utilized to analyze the crystalline and electronic structure of lanthanum orthoniobate substituted by antimony. Using X‐ray absorption spectroscopy and photoelectron spectroscopy, changes in the electronic structure of the material upon substitution have been analyzed. The structural transition temperature between fergusonite and scheelite phases for 30 mol% antimony substitution was found...
-
Preparation and characterisation of iron substituted Mn1.7Cu1.3-xFexO4 spinel oxides (x = 0, 0.1, 0.3, 0.5)
PublicationSpinel oxides with the general formula Mn1.7Cu1.3-xFexO4 (x= 0, 0.1, 0.3, 0.5) were prepared and evaluated in this work for their properties at high temperatures. The effect of partially substituting Cu by Fe has not been studied so far for this group of materials and is thus evaluated in this work. Mn1.7Cu1.3-xFexO4 powders were synthesised by a soft chemistry process and studied in terms of crystallographic phase analysis, electrical...
-
Electric and magnetic properties of Lanthanum Barium Cobaltite
PublicationThe cubic Ba0.5La0.5CoO3‐δ was synthesized using solid state reaction. The structural properties were determined by the simultaneous refinement of Synchrotron Powder X‐ray Diffraction and Neutron Powder Diffraction data. Iodometric titration was used to examine the oxygen stoichiometry and average cobalt oxidation state. Low‐temperature magnetic studies show soft ferromagnetic character of fully oxidized material, with θP = 198(3)...
-
Wojciech Sadowski prof. dr hab. inż.
PeopleWojciech Sadowski (born 2 February 1954 in Ostaszewo, Poland), scientist, engineer, professor at Gdansk University of Technology, specialist in solid state body physics, nanotechnology, optoelectronics. In 1973 he completed his high school education at High School Nicolaus Copernicus in Chelmno. In 1979 he graduate from Leningrad Electrotechnical Institute in Russia (former Soviet Union) with specialism in dielectrics and semiconductors....
-
Modulation of dielectric properties in low-loss polypropylene-based composites at GHz frequencies: theory and experiment
PublicationPolymer composites with high dielectric constant and low loss tangent are highly regarded as substrates for modern high-speed electronics. In this work, we analyze the high-frequency dielectric properties of two types of composites based on polypropylene infused with high-dielectric-constant microparticles. Two types of fillers are used: commercial ceramics or titanium oxide ( TiO2) with different concentrations. The key observation...
-
Werkzeugübergreifende Konsistenzsicherung von Artefakten bei der Entwicklung softwarebasierter Systeme im Automobil
PublicationDie Entwicklung von eingebetteten Systemen im Auto mobilbereich zeichnet sich zunehmend durch steigende Komplexität der zu entwickelnden Fahrzeugfunktionen aus. Die Handhabung dieser Kompl exität wird über entsprechend mächtige Werkzeuge, welche die verschi edenen Aktivitäten des Softwareentwicklungsprozesses unterstützen, angestr ebt. Als eine Schwachstelle erweist sich dabei, dass die eingesetzten Werkzeugk etten im Automobilbereich...
-
Monotone iterative method for first-order differential equations at resonance
PublicationThis paper concerns the application of the monotone iterative technique for first-order differential equations involving Stieltjes integrals conditions. We discuss such problems at resonance when the measure in the Stieltjes integral is positive and also when this measure changes the sign. Sufficient conditions which guarantee the existence of extremal, unique and quasi-solutions are given. Three examples illustrate the results.
-
Influence of controlled crystallization and SrF2 content on the structure and properties of Eu3+ doped phosphate glasses
Open Research DataThe attached data contains the results of measurements of phosphate glasses and glass-ceramics doped with Eu. On their basis, the new material was characterized and the influence of the SrF2 addition on the glass structure was determined. In addition, the influence of the SrF2 content and controlled crystallization on the luminescent properties of Eu3+...
-
The new tool of inverse analysis applied in geotechnics.
PublicationW pracy przedstawiono przykład prostego zastosowania analizy wstecznej do tzw. Współoddziaływującego Układu Projektowania (Systeme Interactif de Conception -SIC). Zastosowanie analizy wstecznej w tym układzie oparte jest na procedurze zaproponowanej przez Gens´a i innych. W omawianej pracy ograniczono się do określenia liniowej odkształcalności wartości modułowej ośrodka ciągłego. Wykorzystano algorytm minimalizujący funkcje...
-
Power devices in Polish National Silicon Carbide Program
PublicationArtykuł zawiera informacje o polskim rządowym programie ''Nowe technologie na bazie węglika krzemu i ich zastosowania w elektronice wielkich częstotliwości, dużych mocy i wysokich temperatur''. Program zawiera trzy główne zadania zawierające następujące cele: wytworzenie podłoży z SiC, wytworzenie przyrządów z SiC oraz ocenę działania wybranych przyrządów w układach aplikacyjnych. Omówiono zastosowane metody wytwarzania podłoży,...
-
Ochrona zdrowia i życia na morzu. Statki szpitale
PublicationRatowanie życia oraz opieka nad chorym w środowisku morskim jest szczególnym wyzwaniem i zadaniem. Na początku XX-tego wieku nastąpił przełom w niesieniu pomocy osobom rannym oraz chorym, którzy ze względu na pobyt na obiekcie pływającym miały ograniczony dostęp do lekarza czy ośrodka zdrowia. Pojawiły się statki, które pełniły rolę pływających szpitali. Ich działalność wynikała z określonych sytuacji niosących zagrożenie dla zdrowia...
-
Effect of User Mobility upon Trust Building among Autonomous Content Routers in an Information-Centric Network
PublicationThe capability of proactive in-network caching and sharing of content is one of the most important features of an informationcentric network (ICN). We describe an ICN model featuring autonomous agents controlling the content routers. Such agents are unlikely to share cached content with other agents without an incentive to do so. To stimulate cooperation between agents, we adopt a reputation and trust building scheme that is able...
-
THE POSSIBILITY OF USE OF LASER-MODIFIED Ti6Al4V ALLOY IN FRICTION PAIRS IN ENDOPROSTHESES
PublicationThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the Ti6Al4V alloy used for orthopedic applications. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. The paper presents the abrasive wear of the base and laser remelted material in association with ceramics Al2O3. Despite the surface cracking after laser treatment the...
-
Materiały stosowane do wytwarzania implantów kości
PublicationMateriały stosowane do wytwarzania implantów kostnych muszą być biokompatybilne, nietoksyczne, bioaktywne oraz wykazywać odpowiednie właściwości mechaniczne, takie jak wytrzymałość na ściskanie, na zginanie oraz sztywność i twardość. Gama stosowanych materiałów jest bardzo szeroka, obejmuje metale, polimery, ceramikę oraz ich kompozyty. Każdy z tych materiałów ma swoje mocne i słabe strony. Praca stanowi przegląd materiałów stosowanych...
-
Water uptake analysis of acceptor-doped lanthanum orthoniobates
PublicationIn this work, lanthanum orthoniobates doped with either antimony, calcium, or both have been synthesized and studied. The water uptake of the investigated materials has been analyzed by means of thermogravimetric studies. The results show the difference between the thermodynamics of hydration between the lanthanum orthoniobate system and other proton conducting ceramics. The relation between the water uptake and effective acceptor...
-
Ocena stanu powierzchni kulek ceramicznych po nagniataniu tocznym stali hartowanej Cf53
PublicationW artykule przedstawiono wyniki z badań eksperymentalnych dotyczących przydatności kulek wykonanych z ceramiki technicznej, do nagniatania tocznego, narzędziami z dociskiem hydrostatycznym. W badaniach wykorzystano narzędzie umożliwiające wymianę kulek nagniatających. Badania wykonano poprzez nagniatanie wałków wykonanych ze stali Cf53 w stanie utwardzonym (zahartowanym). Wyniki badań obejmują charakterystyki stanu powierzchni...
-
Aneta Sobiechowska-Ziegert dr
PeopleShe works at the Department of Statistics and Econometrics at the Faculty of Management and Economics. She is passionate about using modern teaching methods in quantitative subjects. She is a certified coach and tutor. She teaches courses in economic forecasting and spatial econometrics. She is also the chair of the Faculty's Quality of Education Committee and oversees the EMOS education track, certified by Eurostat. Currently,...
-
Results of abrasive slurry dosage in lapping process
PublicationPrzedstawiono wyniki badań dawkowania zawiesiny ściernej w docieraniu powierzchni płaskich elementów ceramicznych. Analizowano wpływ dawkowania na podstawowe parametry chropowatości powierzchni ceramiki Al2O3 i Al2O3-ZrO2.
-
Retinit im mittleren Geiseltal und in Nordwestsachsen
PublicationEs werden historische fossile Harzfunde, bekannt unter dem Namen Retinit, aus ehemaligen Braunkohlenvorkommen in Nordwestsachsen und dem Geiseltal beschrieben. Die Harzproben aus dem Geiseltal wurden mittels Infrarotspektrometer untersucht. Der Vergleich der Spektren mit Referenzspektren zeigt, dass es sich bei den „historischen“ Harzproben um ein Harz vom Retinit- Typ, den oxidierten Krantzit (Oxikrantzit), handelt.
-
A Method and Device for 3D Recognition of Cutting Edge Micro Geometry
Publication -
Roofing Materials as Pollution Emiters - Concentration Changes During Runoff
PublicationThe influence of roofing material on concentration of pollutants in roof runoff waters and changes of pollution concentration in time were investigated. In field studies four roofing material types were taken into consideration - ceramic tile, bituminous membrane, asbestos tile and zinc sheeting. Samples were collected since November 2007 to March 2008, anions, cations, metals, PAHs, pesticides and PCB were determined. The existence...
-
Electromagnetic forced vibrations of composite nanoplates using nonlocal strain gradient theory
PublicationThis article is intended to analyze forced vibrations of a piezoelectric-piezomagnetic ceramic nanoplate by a new refined shear deformation plate theory in conjunction with higher-order nonlocal strain gradient theory. As both stress nonlocality and strain gradient size-dependent effects are taken into account using the higher-order nonlocal strain gradient theory, the governing equations of the composite nanoplate are formulated....
-
Effect of MAO coatings on cavitation erosion and tribological properties of 5056 and 7075 aluminum alloys
PublicationTwo ceramic coatings have been applied on 5056 and 7075 aluminum alloy by microarc oxidation (MAO) technology. The mass losses, surface morphologies and the phase constituents of the MAO coatings before and after cavitation tests were examined by means of digital scales, scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. In order to assess the impact of the mechanical properties of the surface layer on...
-
Nanokrystaliczne warstwy ceramiczne otrzymywane metodą pirolizy aerozolowej w tlenkowych ogniwach paliwowych
PublicationNiniejsza rozprawa doktorska dotyczy badań materiałów wytwarzanych w postaci cienkich, nanokrystalicznych warstw ceramicznych metodą pirolizy aerozolowej dla zastosowań w tlenkowych ogniwach paliwowych (SOFC). Badane są trzy możliwe obszary zastosowań wytwarzanych warstw tj. osadzanie powłok ochronnych na stalowych interkonektorach dostarczających gazy do elektrody tlenowej, wytwarzanie bariery ochronnej zapobiegającej dyfuzji...
-
ZUŻYCIE POWIERZCHNI KULEK CERAMICZNYCH W PROCESIE NAGNIATANIA TOCZNEGO STALI HARTOWANEJ
PublicationPrzedstawiono wyniki z badań eksperymentalnych dotyczących przydatności kulek wykonanych z ceramiki technicznej, do nagniatania tocznego, narzędziami z dociskiem hydrostatycznym. W przeprowadzonych badaniach zastosowano narzędzie umożliwiające wymianę kulek ceramicznych zastosowanych jako elementów nagniatające. Badania wykonano poprzez nagniatanie próbek - wałków wykonanych ze stali Cf53 w stanie utwardzonym (zahartowanym). Wyniki...
-
Wpływ dawkowania zawiesiny ściernej na efekty docierania powierzchni płaskich
PublicationPrzedstawiono wyniki badań dawkowania zawiesiny ściernej podczas docierania powierzchni płaskich. Określono wpływ wielkości dawki ścierniwa na wydajność obróbki i podstawowe parametry chropowatości powierzchni. Obrabiano elementy z ceramiki tlenkowej oraz miedziane.
-
Analiza popytu dla potrzeb zarządzania cenami na przykładzie rynku paliw wPolsce.**2002, 180 s. 32 rys. 32 tab. 32 wykr. bibliogr. 76 poz. maszyn. Rozprawa doktorska (12.06.2002). P. Gdań. Wydz. ZiE. Promotor: dr hab. Jerzy C. Ossowski, prof. nadzw. PG
Publication.
-
A miniaturized solid-contact potentiometric multisensor platform for determination of ionic profiles in human saliva
PublicationThis paper describes a miniaturized multisensor platform (MP-ISES) consisting of electrodes: a reference one (RE) and ion-selective electrodes (ISEs) for monitoring Na+, K+, Ca2+, Mg2+, Cl−, and SCN− ions and pH in human saliva. Gold electrode surface was modified by deposition of two layers: electrosynthesized PEDOT:PSS forming an intermediate layer, and ion-selective membrane. The developed ISEs were characterized by a wide linear...
-
Analiza czasochłonności docierania technologicznego powierzchni płaskich w operacjach montażowych.
PublicationPrzedstawiono wyniki analiz docierania i mikroszlifowania elementów płaskich na docierarce jednotarczowej mikroziarnami węglika krzemu. Obrabiano elementy ze stali 100Cr oraz z tlenkowej ceramiki technicznej Al2O3. Analizowano czas obróbki i koszty operacji.
-
Marta Kuc-Czarnecka dr
PeopleMarta Kuc-Czarnecka is the deputy head of the Department of Statistics and Economics at the Faculty of Management and Economics of the Gdańsk University of Technology. She also serves as the Dean's proxy for AMBA accreditation. She is a co-founder of Rethinking Economics Gdańsk and a member of the Foundation Edward Lipiński for the promotion of pluralism in economic sciences. In 2018-2022, she was Eurofound’s quality of life and...
-
Sliding friction of alumina (Al2O3) with friction induced vibrations
Open Research DataTest files containing data on experiments in self mated sliding contact of alumina Al2O3 lubricated with either water or paraffin oil. Tests run in variable load/velocity conditions and with different dynamic settings of the test rig (PT-3 tribometer). The aim of the research was to attempt in finding correlations between the dynamic characteristics...
-
Udział nośny powierzchni elementów ceramicznych i węglików spiekanych po docieraniu.
PublicationPrzedstawiono wyniki badań docierania jednotarczowego powierzchni elementów z ceramiki technicznej i węglików spiekanych. Analizowano jakość obróbki i udział nośny powierzchni po docieraniu. Docieranie powierzchni płaskich jest technologią pozwalającą uzyskać duży udział nośny.
-
Stanowisko do pomiaru termicznej stałej czasowej bolometrów
PublicationPrzedstawiono stanowisko umożliwiające pomiar termicznej stałej czasowej bolometrów. Stanowisko to składa się z dwóch układów pomiarowych połączonych z cyfrowym analizatorem sygnału i umożliwia pomiar stałej czasowej w zakresie od pojedynczych milisekund do kilku sekund. Omówiono budowę i działanie opracowanych układów i zaprezentowano wyniki pomiarów stałej czasowej bolometrów z niestechiometrycznych tlenków lantanowo-strontowo-żelazowych...
-
Method of Monitoring of the Grinding Process with Lapping Kinematics Using Audible Sound Analysis
PublicationUtilising microphones as audible sound sensors for monitoring a single-side grinding process with lapping kinematics is presented in the paper. The audible sound generated during grinding depended on the cutting properties of electroplated tools with D107 diamond grains and different thicknesses of the nickel bond. The tool wear affected the obtained technological effects such as material removal rate and the surface roughness...
-
Nanotubular oxide layers and hydroxyapatite coatings on ‘Ti–13Zr–13Nb’ alloy
PublicationThe presented research was aimed to determine the mechanical properties of the nanotubular oxide layer covered with hydroxyapatite coating. The Ti–13Zr–13Nb alloy was oxidised in 1M phosphoric acid with an addition of 0?5% HF for HF solution at 20 V voltage. The electrochemically assisted deposition of hydroxyapatite was performed at cyclic polarisation in NH4H2PO4 and CaCl2 solution at 80uC. The mechanical properties were determined...
-
Thermochemical Conversion of Biomass and Municipal Waste into Useful Energy Using Advanced HiTAG/HiTSG Technology
PublicationAn advanced thermal conversion system involving high-temperature gasification of biomass and municipal waste into biofuel, syngas or hydrogen-rich gas is presented in this paper. The decomposition of solid biomass and wastes by gasification is carried out experimentally with a modern and innovative regenerator and updraft continuous gasifier, among others. A ceramic high-cycle regenerator provides extra energy for the thermal conversion...
-
Effects of La Content on the Densification, Microstructure, and Conductivity of Doped La10−x Ge6 O26±δ Electrolytes
PublicationIn this study, the influence of La content on the characteristics of Nb-, Mo-, and W-doped LaxGe6O26±δ electrolytes was investigated through sintering study, X-ray diffraction, scanning electron microscopy, and conductivity measurement. The densification of LaxGe5.5Nb0.5O26±δ and LaxGe5.5W0.5O26±δ was retarded as the x reached 9.75, while that of LaxGe5.5Mo0.5O26±δ improved with increasing La content. The average grain size slightly...
-
Influence of yttria surface modification on high temperature corrosion of porous Ni22Cr alloy
PublicationProtective coatings for porous alloys for high temperature use are relatively new materials. Their main drawback is high temperature corrosion. In this work protective coatings based the on Y-precursor infiltrated into the sintered Ni22Cr alloys are studied at 700°C. Effects of the amount of the protective phase on the resulting corrosion properties are evaluated in air and humidified hydrogen. Weight gain of the samples, their...
-
Selection of material for X-ray tomography analysis and DEM simulations: comparison between granular materials of biological and non-biological origins
PublicationPhysical properties and X-ray tomography images of five different granular materials: glass bead, glass grit, short grain white rice, sorghum and clay granules (Seramis) are investigated to select the most promising materials for numerical simulations and time-lapse X-ray tomography imaging. The examined materials represent granular materials of non-biological origin (glass bead, glass grit and Seramis) and granular plant materials...
-
Ocena czynnej powierzchni narzędzia w mikroszlifowaniu powierzchni płaskich z kinematyką docierania jednotarczowego
PublicationPrzedstawiono wyniki badań eksperymentalnych mikroszlifowania z kinematyką docierania w układzie jednotarczowym. Badania miały na celu wyznaczenie okresu trwałości narzędzia i zmieniających się w czasie jego właściwości ściernych. Badania przeprowadzono na próbkach z ceramiki aluminiowej.
-
Wpływ zawiesiny ściernej dawkowanej w sposób wymuszony na wydajność docierania jednotarczowego elementów ceramicznych
PublicationPrzedstawiono zagadnienia związane z przygotowywaniem zawiesiny ściernej w docieraniu maszynowym powierzchni płaskich. W badaniach zastosowano wymuszony sposób dozowania zawiesiny na docierak żeliwny. Badano docieranie elementów z ceramiki tlenkowej zawiesiną na bazie mikroziaren węglika krzemu.
-
CERVIX UTERI, Exocervix - Female, 33 - Tissue image [9160729581057141]
Open Research DataThis is the histopathological image of CERVIX UTERI tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
CERVIX UTERI, Exocervix - Female, 33 - Tissue image [9160729581053791]
Open Research DataThis is the histopathological image of CERVIX UTERI tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
CERVIX UTERI, Exocervix - Female, 33 - Tissue image [9160729581058731]
Open Research DataThis is the histopathological image of CERVIX UTERI tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
CERVIX UTERI, Exocervix - Female, 33 - Tissue image [9160729581051671]
Open Research DataThis is the histopathological image of CERVIX UTERI tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
CERVIX UTERI, Exocervix - Female, 33 - Tissue image [9160729581056491]
Open Research DataThis is the histopathological image of CERVIX UTERI tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.