Filters
total: 1325
displaying 1000 best results Help
Search results for: MAGNETIC SEMICONDUCTORS
-
Structure and hyperfine interactions in Bi1−xNdxFeO3 solid solutions prepared by solid-state sintering
PublicationThe series of polycrystalline ceramic powders, Bi1xNdxFeO3 (x = 0.11) was successfully synthesized by mixed oxide method followed by pressureless sintering. X-ray diffraction and Mössbauer spectroscopy were used as complementary methods to study structure and hyperfine interactions of the samples. It was found that with an increase of Nd content, within the range of x = 0.20.3 a structural phase transition from rhombohedral to...
-
Effect of power frequency on the stress state of disc actuator
PublicationThis paper presents the concept of determining the optimum frequency of coil supply in inductive-dynamic drive. As a criterion to obtain the sought frequency, the smallest value of reduced stress in the disc was assumed while maintaining the desired dynamics. The disc stress is determined on the basis of solution of vibrating thin plate equation. Magnetic pressure acting on the disc is obtained from a hybrid circumferentially-field...
-
Sample Rate Conversion with Fluctuating Resampling Ratio
PublicationIn this paper a sample rate conversion with continuouslychanging resampling ratio has been presented. The proposed implementation is based on variable fractional delay filter implemented using a Farrow structure. It have been demonstrated that using the proposed approach instantaneous resampling ratio can be freely changed. This allows for simulation of audio recored on magnetic tape with nonuniform velocity as well as removal...
-
Resonant Frequencies in Microstrip Structure with Omega Medium Substrate
PublicationThe paper presents the research on a rectangular microstrip structure with multilayer substrate containing dielectric and omega medium layers. The effect of pseudochiral medium layer location in the substrate and its thickness on the resonant frequency of the rectangular microstrip structure is investigated. The numerical analysis of investigated structures is based on expansion of electric and magnetic fields. Utilizing the continuity...
-
Taguchi sensors under temperature modulation
PublicationSemiconductor gas sensors are widely used in gas- analyzing applications for various gas species determination due to their low cost and possibility to detect number of different gases. However, one of the main problems with such sensors is their lack of selectivity. To overcome this issue different ap- proaches can be used. One of them is the operation with sensor temperature modulation combined with dedicated data process- ing...
-
Quality evaluation of agricultural distillates using different types of electronic noses
PublicationThe paper presents the results of investigation on quality evaluation of agricultural distillates using a prototype of electronic nose instrument and a commercial electronic nose of Fast/Flash GC type – HERACLES II. The prototype was equipped with TGS type semiconductor sensors. HERACLES II included two chromatographic columns with different polarity of stationary phase and two FID detectors. In case of the prototype volatile fraction...
-
Microfluidic devices for photo-and spectroelectrochemical applications
PublicationThe review presents recent developments in electrochemical devices for photo- and spectroelectrochemical investigations, with the emphasis on miniaturization (i.e., nanointerdigitated complementary metal-oxide-semiconductor devices, micro- and nano-porous silicon membranes or microoptoelectromechanical systems), silica glass/microreactors (i.e., plasmonic, Raman spectroscopy or optical microcavities) or polymer-based devices (i.e.,...
-
Dielectric Spectroscopy Studies and Modelling of Piezoelectric Properties of Multiferroic Ceramics
PublicationCompounds and solid solutions of bismuth ferrite (BiFeO3)—barium titanate (BaTiO3) system are of great scientific and engineering interest as multiferroic and potential high-temperature lead-free piezoelectric materials. In the present paper, the results of research on the synthesis and characterisation of 0.67Bi1.02FeO3–0.33BaTiO3 (67BFBT) ceramics in terms of crystal structure and dielectric and piezoelectric properties are reported....
-
Design and Preparation of Magnetically-Oriented Poly(styr-co-MMA)-3MPS Capped Fe(ZnO) Hybrid Microspheres for Ion Exchange Removal of Toxic Pollutants from Wastewater
PublicationIn this work, polymeric microspheres derived from polystyrene-co-methyl methacrylate embedded with magnetic ZnO nanoparticles (poly(styrene-co-MMA)-3MPS-Fe (ZnO)) were synthesized using the suspension polymerization method. The surfaces of polymeric Fe(ZnO) microspheres were improved by functionalization with amino and sulphonate groups. The physicochemical analysis indicated a large number of positively charged (anion exchange)...
-
Sample Rate Conversion with Fluctuating Resampling Ratio
PublicationIn this paper a sample rate conversion with continuously changing resampling ratio has been presented. The proposed implementation is based on variable fractional delay filter implemented using a Farrow structure. It have been demonstrated that using the proposed approach instantaneous resampling ratio can be freely changed. This allows for simulation of audio recored on magnetic tape with nonuniform velocity as well as removal...
-
Gains selection of non-proportional observers of an induction motor with dyadic methods
PublicationThe paper presents issues related to calculation of gains of non-proportional observers of magnetic fluxes of an induction motor. A transformation is discussed, based on dyadic matrices, that affords possibility of applying well-known methods used in single-output systems to observers of multi-output systems. The impact of dyadic transformation on possibility of poles placement of the observer is analyzed....
-
The Effects of Cross-Link Density and Chemical Exchange on Magnetization Transfer in Polyacrylamide Gels
Publication -
The description of non-linear interactions of wave and non-wave modes in a non-adiabatic plasma flow
PublicationThe method of derivation of non-linear equations for interacting modes is explained and applied to a plasma's flow affected by a magnetic field. It is based on the linear projecting of the total perturbation field into specific variations of variables in individual modes of a flow. The method may be applied in many examples of fluid flows with different mechanisms of non-adiabaticity. It is of special importance in complex flows...
-
Evaluation of structural change during fast transformation process of cross-linked NR into liquid NR by light pyrolysis
PublicationThe presence of cross-linked networks in rubber creates a tremendous problem for recycling and reusing of waste rubber. Fast transformation of cross-linked natural rubber (NR) into liquid natural rubber was carried out by light pyrolysis in temperature range from 240 to 300 °C in variable time (in range: 1–30 min). The transformation efficiency was evaluated by measuring the sol fraction and the cross-link density of the gel fraction....
-
Biocompatibility and potential functionality of lanthanum-substituted cobalt ferrite spinels
PublicationBulk and nanostructurized lanthanum-cobalt spinels have attracted a lot of interest from researchers, due to their unique physical and chemical properties as well as functionalities, which are interesting for biomedical and electronic industries. In this manuscript we show that introducing small lanthanum (La3+) content can tune magnetic, electronic and cytotoxic properties of the CoFe2− xLaxO4 system (x ≤ 0.1). The mechanisms...
-
Spin-glass behavior in a binary Pr 3 Ir intermetallic compound
PublicationPolycrystalline Pr3Ir was synthesized by arc melting. Its cementite-type crystal structure (Pnma) was confirmed by powder X-ray diffraction and estimated lattice parameters are in agreement with literature. Physical properties were measured by means of the ac and dc magnetic susceptibility, electrical resistivity and heat capacity. Our results indicate spin-glass behavior in Pr3Ir with a freezing temperature Tf = 6.58 K and activation...
-
Absence of superconductivity in fluorine-doped neptunium pnictide NpFeAsO
PublicationX-ray diffraction, specific heat, magnetic susceptibility and inelastic x-ray scattering measurements on the transurarium oxypnictides NpFeAsO and NpFeAsO0.85F0.15 are presented. No superconductivity down to 2 K was observed upon fluorine doping, contrary to the structurally analogous rare-earth pnictides. No modification of the phonon density of states was observed upon doping with fluorine. We discuss our results in light of...
-
Superconductivity and appearance of negative magnetocaloric effect in Ba1–xKxBiO3 perovskites, doped by Y, La and Pr
PublicationRecently, substantial attention is given to the bismuth-based perovskites for variety of electronic applications. The perovskites are used for quantum dots displays (QLED), photovoltaic systems and superconducting (HTS) devices. In this paper comprehensive studies of Ba1–xKxBi1–yREyO3 bismuth perovskites (REBKBO, RE = Y , La or Pr) are reported. Apart from structural anomalous behavior at low temperatures, the electronic properties...
-
Assessment of dynamic characteristics of thin cylindrical sandwich panels with magnetorheological core
PublicationBased on the equivalent single-layer linear theory for laminated shells, free and forced vibrations of thin cylindrical sandwich panels with magnetorheological core are studied. Five variants of available magnetorheological elastomers differing in their composition and physical properties are considered for smart viscoelastic core. Coupled differential equations in terms of displacements based on the generalized kinematic hypotheses...
-
Analogue CMOS ASICs in Image Processing Systems
PublicationIn this paper a survey of analog application specific integrated circuits (ASICs) for low-level image processing, called vision chips, is presented. Due to the specific requirements, the vision chips are designed using different architectures best suited to their functions. The main types of the vision chip architectures and their properties are presented and characterized on selected examples of prototype integrated circuits (ICs)...
-
Thickness and structure change of titanium (IV) oxide thin films synthesized by the sol–gel spin coating method
PublicationTitanium dioxide is a well-known material in nanotechnology, while it provides new opportunities due to its interesting properties, for example, as a semiconductor with a quite significant forbidden band gap energy of 3.2 eV. In this study, thin films of titanium dioxide (TiO2) were synthesized in amorphous and crystallographic systems using the sol–gel process. Atomic Force Microscopy (AFM), Raman spectroscopy and X-ray diffraction...
-
Non-metaldoped TiO2 nanotube arrays for high efficiency photocatalytic decomposition of organic species in water
PublicationTitanium dioxide is a well-known photoactive semiconductor with a variety of possible applications. The procedure of pollutant degradation is mainly performed using TiO2 powder suspension. It can also be exploited an immobilized catalyst on a solid support. Morphology and chemical doping have a great influence on TiO2 activity under illumination. Here we compare photoactivity of titania nanotube arrays doped with non-metal atoms:...
-
Detection of gaseous compounds with different techniques
PublicationSensing technology has been developed for detection of gases in some environmental, industrial, medical, and scientific applications. The main tasks of these works is to enhance performance of gas sensors taking into account their different applicability and scenarios of operation. This paper presents the descriptions, comparison and recent progress in some existing gas sensing technologies. Detailed introduction to optical sensing...
-
Ring thruster - a preliminary optimisation study of ferrofluid seal and propeller
PublicationThe article reports the course of preliminary examination of a ferrofluid seal applied in liquid environment.A newly built research rig is described, and results of pressure tests performed for different shaft rotationsare discussed. Other studies carried out in the past only referred to the gas environment, while the presentexamination aims at finding an answer to the question whether magnetic liquids can be successfully used...
-
Cross-border transmission line configuration influence on the electrical power and energy billing process
PublicationIn 2015 a connection between the Polish and Lithuanian power systems become fully operational. The connection consists of a 400 kV double circuit transmission line and a back-to-back HVDC substation located on the Lithuanian side. A magnetic couplings between the circuits of the transmission line cause that during power transmission a different values of active power losses are observed in both circuits. This situation may cause...
-
Experimental comparison of the transition speed of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublicationA journal bearing test bench is used to find the transition speed between the hydrodynamic and mixed lubrication regimes for a modified magnetorheological (MR) fluid. It is shown that the transition speed of the bearing can be reduced by applying a local magnetic field near minimum film when it is lubricated with the MR fluid, and that this will only marginally increase friction. The lubricating performance of the MR fluid is compared...
-
Locating and Identifying Ferromagnetic Objects
PublicationThe new non-iterative method of determining the dipole moment and location is presented in this paper. The algorithm of an object's localization and identification was achieved by using numerical calculations and approximation method. The arbitrary shapes of an object were assumed in the identification algorithm - axially symmetric spheroid (a prolate and an oblate). Several examples of localization and identification of an object's...
-
Multi-Transformer Flyback Converter for Supplying Isolated IGBT and MOSFET Drivers
PublicationA multi transformer flyback converter topology for supplying transistor drivers is presented. The topology presents some advantages over typical multi output single transformer, as reduction of effective leakage inductance, equal magnetic coupling between primary and secondary circuits and better isolation between outputs. Simulation study carried out in the LTSpice IV program and preliminary experimental results indicate high...
-
Hysteresis modelling of a medium frequency single-phase transformer
PublicationThe article describes a feedback Preisach hysteresis model equivalent circuit implementation of a medium frequency single-phase transformer being a part of a high power and high efficiency DC-DC converter. The macroscopic models of magnetic hysteresis are introduced and the feedback Preisach model is selected for further analysis. The hysteresis model is developed for a prototype transformer and the hysteresis loops are compared...
-
Locating and Identifying Ferromagnetic Objects
PublicationThe new non-iterative method of determining the dipole moment and location is presented in this paper. The algorithm of an object's localization and identification was achieved by using numerical calculations and approximation method. The arbitrary shapes of an object were assumed in the identification algorithm - axially symmetric spheroid (a prolate and an oblate). Several examples of localization and identification of an object's...
-
Improved methods for stator end winding leakage inductance calculation
PublicationCalculating the stator end-winding leakage inductance, taking into account the rotor, is difficult due to the irregular shape of the end-winding. The end-winding leakage may distribute at the end of the active part and the fringing flux of the air gap. The fringing flux belongs to the main flux but goes into the end-winding region. Then, not all the magnetic flux occurring in the end region is the end-winding leakage flux. The...
-
Koncepcja i modelowanie silnika o wirującym tworniku oraz magneśnicy do zastosowania w napędzie miejskiego samochodu elektrycznego
PublicationW artykule zaprezentowano koncepcję, model oraz prototyp silnika z wirującym twornikiem oraz magneśnicą. Opisano historię powstania i zastosowania tego typu silników w motoryzacji. Przedstawiono nowoczesne rozwiązania konstrukcyjne i zastosowania we współczesnych samochodach elektrycznych i hybrydowych. Opracowano model silnika z wirującym twornikiem i magneśnicą oraz przedstawiono wybrane wyniki symulacji przeprowadzone w programie...
-
Hybrid quantum-classical approach for atomistic simulation of metallic systems
PublicationThe learn-on-the-fly (LOTF) method [G. Csanyi et al., Phys. Rev. Lett. 93, 175503 (2004)] serves to seamlessly embed quantum-mechanical computations within a molecular-dynamics framework by continual local retuning of the potential's parameters so that it reproduces the quantum-mechanical forces. In its current formulation, it is suitable for systems where the interaction is short-ranged, such as covalently bonded semiconductors....
-
Ionic liquids for nano- and microstructures preparation. Part 2: Application in synthesis
PublicationIonic liquids (ILs) are widely applied to prepare metal nanoparticles and 3D semiconductor microparticles. Generally, they serve as a structuring agent or reaction medium (solvent), however it was also demonstrated that ILs can also play a role of a co-solvent, metal precursor, reducing as well as surface modifying agent. The crucial role and possible types of interactions between ILs and growing particles have been presented in...
-
Selected dynamic properties of adaptive proportional observer of induction motor state variables
PublicationThis paper presents problems related to the design and the stability of adaptive proportional observer which is used for estimation of magnetic flux and motor speed in sensorless control systems of induction motor. The gain matrix of the observer was chosen by genetic algorithm and alternatively by pole placement method. It has been shown that adaptive proportional observer is stable if the...
-
Determination of leakage inductances of multi-winding and single-phase transformer
PublicationThis paper presents the method for determination of leakage inductances of single-phase and multi-winding transformer. The matrix of leakage inductances takes into account leakage self and also leakage mutual magnetic couplings. It is assumed that there is a flux common to all windings and several leakage fluxes referred to a particular winding. The flux linkages of each coil needed fo calculation of leakage inductances was computed...
-
Quality Evaluation of Agricultural Distillates Using an Electronic Nose
PublicationThe paper presents the application of an electronic nose instrument to fast evaluation of agricultural distillates differing in quality. The investigations were carried out using a prototype of electronic nose equipped with a set of six semiconductor sensors by FIGARO Co., an electronic circuit converting signal into digital form and a set of thermostats able to provide gradient temperature characteristics to a gas mixture. A volatile fraction...
-
Comparison of the Measurement Techniques Employed for Evaluation of Ambient Air Odour Quality Influenced by Operation of Industrial Sewage Treatment Plant
PublicationThe paper presents the results of investigation on ambient air quality evaluation with respect to concentration of odorants in a vicinity of a sewage treatment plant of the LOTOS Group S.A. petroleum plant. The investigation was performed during winter season using a prototype of electronic nose and the Nasal Ranger field olfactometers. The prototype was equipped with a set of six semiconductor sensors by FIGARO Co. and one PID-type...
-
Evaluating experimental molecular physics studies of radiation damage in DNA*
PublicationThe field of Atomic and Molecular Physics (AMP) is a mature field exploring the spectroscopy, excitation, ionisation of atoms and molecules in all three phases. Understanding of the spectroscopy and collisional dynamics of AMP has been fundamental to the development and application of quantum mechanics and is applied across a broad range of disparate disciplines including atmospheric sciences, astrochemistry, combustion and environmental...
-
Monitoring of odour nuisance in the Tricity Agglomeration
PublicationThe paper describes a principle of operation of odour nuisance monitoring network, which is being designed in the Tricity Agglomeration. Moreover, it presents the preliminary results of an investigation on ambient air quality with respect to odour nuisance in a vicinity of the municipal landfill. The investigation was performed during spring-winter season using a prototype of electronic nose and the Nasal Ranger field olfactometers. The...
-
Comparison of the measurement techniques employed for evaluation of ambient air odour quality
PublicationThe paper presents the results of investigation on ambient air odour quality in a vicinity of the industrial sewage treatment plant being a part of the crude oil processing plant. The investigation was performed during spring-winter season using a prototype of electronic nose and the Nasal Ranger field olfactometers. The prototype was equipped with a set of six semiconductor sensors by FIGARO Co. and one PID-type sensor. The field...
-
Iridium 5d -electron driven superconductivity in ThIr3
PublicationA polycrystalline sample of superconducting ThI r 3 was obtained by arc-melting Th and Ir metals. Powder x-ray diffraction revealed that the compound crystalizes in a rhombohedral crystal structure (R-3m, s.g. #166) with the lattice parameters: a = 5.3394 ( 1 ) Å and c = 26.4228 ( 8 ) Å . Normal and superconducting states were studied by magnetic susceptibility, electrical resistivity, and heat capacity measurements. The results...
-
Chemical Characteristics and Thermal Oxidative Stability of Novel Cold-Pressed Oil Blends: GC, LF NMR, and DSC Studies
PublicationPlant oils contain a high content of unsaturated fatty acids. Studies of food products have revealed a considerable disproportion in the ratio of ω6 to ω3. This article presents information on the healthful qualities of eight new oil blends that contain a beneficial proportion of ω6 to ω3 fatty acids (5:1), as well as their degradation during heating at 170 and 200 °C. The fatty acid profile was analyzed by gas chromatography (GC),...
-
Photovoltaic bulk heterojunctions with interpenetrating network based on semiconducting polymers
PublicationPhotovoltaic cells are supposed to be the most common generators of useful electricity in the nearest future as they utilize inexhaustible carriers of renewable energy called photons. Despite the fact that 95% of worldwide applied photovoltaic devices are based on inorganic semiconductors the area of organic photovoltaics grows successively due to possibility of considerable reduction of manufacturing costs. Since the Heeger's...
-
SSFR Test of Synchronous Machine for Different Saturation Levels using Finite-Element Method
PublicationIn this paper the StandStill Frequency Response characteristics (SSFR) of saturated synchronous generator (SG) have been calculated using Finite Element Method (FEM) analysis. In order to validate proposed approach for unsaturated conditions FEM simulation from Flux2D software has been compared with the measurements performed on the 10 kVA, 4- poles synchronous machine ELMOR GCe64a of salient rotor construction, equipped with a...
-
Superconducting properties of vn-sio 2 sol-gel derived thin films
Publicationin this work studies of structure and superconducting properties of vnsio2 films are reported. the films were obtained through thermal nitridation (ammonolysis) of solgel derived v2o3sio2 coatings (in a proper v2o3/sio2 ratio) at 1200 ◦c. this process leads to the formation of disordered structure with vn metallic grains dispersed in the insulating sio2 matrix. the structural transformations occurring in the lms as a result...
-
What are the true volumes of SEGA tumors? Reliability of planimetric and popular semi-automated image segmentation methods
Publication -
Calibration-Free Single-Anchor Indoor Localization Using an ESPAR Antenna
PublicationIn this paper, we present a novel, low-cost approach to indoor localization that is capable of performing localization processes in real indoor environments and does not require calibration or recalibration procedures. To this end, we propose a single-anchor architecture and design based on an electronically steerable parasitic array radiator (ESPAR) antenna and Nordic Semiconductor nRF52840 utilizing Bluetooth Low Energy (BLE)...
-
Comparison of Impedance-Source Networks for Two and Multilevel Buck–Boost Inverter Applications
Publicationmpedance-source networks are an increasingly popular solution in power converter applications, especially in single-stage buck-boost power conversion to avoid additional front-end dc-dc power converters. In the survey papers published, no analytical comparisons of different topologies have been described, which makes it difficult to choose the best option. Thus, the aim of this paper is to present a comprehensive analytical comparison...
-
The influence of the size of a one-faced metallic head in Janus nanoparticles as a co-catalyst on the photocatalytic efficiency of hydrogen evolution under vis light irradiation
PublicationJanus nanoparticles (NPs) consisting of MoOxSy nanospheres and silver (Ag) head, successfully developed by a simple, controlled method were in the first time they were applied as a co-catalysts in photocatalytic hydrogen generation reaction under vis light irradiation (λ > 420 nm). The MoOxSy-Ag as a co-catalysts were deposited on the obtained ZnIn2S4 microspheres (ZIS) using physical absorption method. The influence of the size...